Search Documents

By Donelson A. Robertson

Literature was searched and cases of alleged water well damage were investigated. Occurrence of ground water in Appalachia is primarily in low yield, fractured, water table aquifers. Four test sites were chosen based on geographic and geologic diversity. Test wells were drilled at each site and base line data on water quality, static water level, and drawdown characteristics were obtained before surface mining commenced. Blast induced ground vibrations were measured at the surface by the wells at levels up to 5.44 inches per second maximum resultant particle velocity. Measurements made at the bottom wells indicated that vibrations were considerably attenuated at depths of 140 to 160 feet. No direct evidence of change in water quality or well performance was produced by blast vibrations, but removal of downslope support by excavation does cause lateral stress relief which permits the water-bearing fractures to become more open. This additional storage capacity causes the static water level to drop and for well-bore permeability to improve. Static water level recovers if sufficient recharge is available and well performance is improved.

Jan 1, 1980

By E. C. Lane

"INTRODUCTION The first important discovery of petroleum in New Mexico was near Dayton, Eddy County, where the Brown well was drilled in 1909, and small quantities of oil were produced. In 1911 and 1912 wells were drilled in McKinley County, but commercial production did not begin until the discovery of the Hogback field, San Juan County, in 1922. The discovery well in the Artesia field, Eddy County, drilled in 1923, gave impetus to active drilling in many areas. Since 1924 New Mexico has produced petroleum in commercial quantities and since 1930 the State has joined the ranks of the big produc¬ing States, being sixth or seventh in total production in recent years.Production by years. 1924 to 1940, inclusive, taken from annual figures in Bureau of Mines Minerals Yearbook, are given in table 1. The total production shown is 274,331,000 barrels. Andreas 3/ has published production figures for the year 1940 and a resume of all production to the end of 1940. Data from his report are presented in table 2 for each field sampled. The cumulative production, as given by Andreas, is 270,618,575 barrels."

Aug 1, 1942

By Lloyd Williams

1. The investigation shows that the Sewanee bed is the only bed of major importance in Marion County, 97 percent of the coal mined in the county having come from this bed. There are coal reserves in minor quantity in the Battle Creek bed, and production from this bed depends on a few small truck mines. The Richland bed, or Lower Sewanee, has been mined in the past, but no coal has been produced from it in late years. There are no production records of any other beds in the county, although same coal has been produced from them. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated to be 61 million short tons as of January 1, 1953. Of this total, 55 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate where available data relative to the bed characteristics are too meager to permit making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By Frederick C. Trutt

A guide to the utilization and development of extensions and modifications to the APL Mine-electrical-system Load-flow Program is presented. These modifications include the development of algorithms to minimize computational operations within the iterative-solution techniques, as well as minimization of the number of required iterations. Extensions to the load-flow program include the development of algorithms for the calculation of balanced faults, simplified specification of fault parameters, optional inclusion of pre-fault currents, and an alternate-solution technique.

Jan 1, 1978

By Manuel Gomez

This report presents experimental work conducted on a number of coals found within the boundaries of the Missouri River Basin, which were, to an extent, a selection of coals typical of that region. In the min, the laboratory work falls into three general classifications: (1) Laboratory distillation assay of coal to establish yields on carbonization; (2) chemical analyses of the coal samples before drying or carbonization; and (3) chemical analyses of the products of carbonization. It will be seen in the following discussion that these data derived from the small-scale laboratory apparatus are useful in predicting yields from pilot plants or industrial units. Coal is produced in about 48 general areas or mining fields in the Western States, of which approximately 18 fall within the limits of the Missouri Basin.3/ Beginning with the Northern Colorado field, through the Central and Western Wyoming fields, the coal is principally bituminous and subbituminous rank. The western Montana coals are also of these ranks. Progressing northeast from central Wyoming the coal decreases in rank, as shown by the subbituminous C coals of the Gillette field in northern Wyoming and the lignites of eastern Montana and North Dakota.

Jan 1, 1953

By H. B. Brunot

A complete list of permissible mine equipment , tested and approved by the Bureau of Mines previous to January 1 , 1947 , was published as Information Circular 7432.27 A list of permissible mine equipment tested and approved by the Bureau of Mines during the calendar year 1947 was published as Information Circular 7465.3/ The present list supplements Information Circular 7432 and includes all of the equipment approved during the calendar years 1947 , 1948 , and 1949. It therefore supersedes Information Circular 7465. The list also includes an appendix ( No. 2 ) giving the symbol that must be used by every cable manufacturer in marking trailing cables that have passed the test for flame resistance as stated in the amendment of October 21 , 1947 , to Schedule 2E . The items are numbered to indicate the consecutive order in which each type of machine or device was approved in its particular classification . Thus , Information Circular 7432 showed six air compressors on the active list ; five additional compressors , Nos . 7 to 11 , inclusive , in this category were approved during 1947 , 1948 , and 1949 . Several items that were listed in Information Circular 7432 have been repeated in this circular where it was necessary to show that approvals of such equipment were extended to cover an additional voltage rating or other changes . Equipment listed in these circulars is approved by the Bureau of Mines only when found , upon inspection and test , to comply with minimum standards of safety as outlined in schedules prepared on the basis of many years of experience in dealing with safety problems of the coal -mining industry . The use of such equipment in mines known to be gassy , as well as in those that may become so , is earnestly recommended in the interest of safety . This circular is published so that the industry may be kept informed as to the many types of machines , devices , and lamps that are available for reducing explosion and other hazards incident to coal mining . This circular and Information Circular 7432 give the complete list of permissible mine equipment that is available under the various classifications .

May 1, 1950

By C. A. Pearson, W. D. Dietzman, M. E. Hawkins

Results of chemical analyses and electrical resistivity measurements of 422 samples of oilfield brines from 120 east Texas fields in Railroad Commission of Texas Districts 5 and 6 are presented in tabular form . These samples represent water from all of the major petroleum- productive formations in the area . Water analyses and electrical resistivity data , when fully utilized by proper study techniques , are useful tools in the solution of many engineering problems such as detection of well leaks , identification of water sources , and interpretation of electrical well logs . In the area included in this study , these representative data should facilitate the solution of problems in which water analysis and water resistivity are factors .

Jan 1, 1964

By Doug Tesarik

The study of neutrinos?particles infinitesimally smaller than atoms?would be significantly advanced if a deep underground facility were available that would filter out unwanted cosmic radiation. Encouraging progress has been made in satisfying the criteria for such a facility with the selection of the Homestake Mine in Lead, SD, by the National Underground Laboratory Committee as the recommended site for a National Underground Science Laboratory (NUSL). The Homestake Mine is America?s oldest and deepest underground mine, and its well-maintained infrastructure to depths of 2438 m below the surface makes the mine an excellent site for such a laboratory. The investigation reported here is an initial study of the stability of the first of the proposed chambers. A cylindrical room with a dome-shaped roof and floor was analyzed in three dimensions using the finite-difference program FLAC3D. The results were compared to recommended support requirements based on Barton?s Tunneling Quality Index, Q. Based on model results and observations from previous mining studies, large rooms with 50-m roof spans can be constructed and will remain stable at 2141 m below the surface in the Poorman Formation when the rock is reinforced with cable bolts. Construction may be possible at lower levels in the Yates Formation if more extensive laboratory strength tests confirm initial results.

Jan 1, 2002

By R. F. Kendall

Only a limited number of mass and infrared reference spectra of high purity unsaturated hydrocarbons and oxygenates are presently available in the literature. To aid Bureau of Mines research programs requiring such references, 64 mass spectra and 70 infrared spectra were obtained and are reported. The individual compounds, acquired from commercial sources, were purified by preparatory gas chromatography. Purity determinations were made using a combination of analytical gas chromatography, microhydrogenation, and catalytic deoxygenation. These spectra will aid spectroscopists in the identification of compounds of the types reported.

Jan 1, 1966

By John H. Hild

This is a report on work done and results obtained in a minerals exploration program conducted by the Bureau of Mines on the lead-zinc deposits in the Ross Basin-Lake Como district, San Juan County, Colo., in 1948, 1949, and 1950. Four large veins--the Seven Thirty, Red Rogers, Cashier-Shorts top-Canandaigua, and Queen Anne--and several narrow spur veins were explored at relatively shallow depths with core-drill holes. Thirty-nine holes, totaling 10,491.5 feet, were drilled, and the core samples were assayed at the Bureau of Mines station at Salt Lake City, Utah.

Jan 1, 1959

By H. M. Smith

The production of oil during the early development of new oil fields is usually accompanied by large quantities of natural gas. Since in most fields gas under pressure is the main source of the energy causing the oil to move through the sands into the wells and thence to the surface, coincident production of natural gas will continue as long as present-day producing methods are used. Generally the use of this gas is restricted, since markets are not readily available. Consequently, a large portion of the gas produced is often wasted by being blown into the air. The magnitude of gas waste is well brought out in the following statement by Miller: Only a few outstanding examples need be cited to show the enormous production of gas that accompanies the discovery of new sources. In April, 1927, the Ventura field produced approximately 210,000,000 cubic feet of gas a day; and during the summer of 1927 Alamitos Heights reached a peak gas production of 102,000,000 cubic feet a day; on December 1, 1928, as a result of the summer's deeper drilling in the Long Beach field, surplus gas production amounted to 125,000,000 cubic feet a day. It is estimated that in January, 1929, the Santa Fe Springs field will have a daily gas production of 387,000,000 cubic feet from the recently discovered Buckbee oil zone. Of this amount 274,000,000 cubic feet a day will be the surplus above the amount required for field and plant fuel, taken out by utility corporations, and that used in repressuring the Meyer sand which lies above the Buckbee zone. Another example of the waste of large volumes of gas is in the Turner Valley field of Canada, 6 where 250,000,000 cubic feet of gas is being burned daily in flambeaus, as there is no present outlet except at prohibitive cost.

Jan 1, 1931

By W. H. Young

The thickness of the coal seam is one of the more important items influencing the productivity and general overall efficiency of operation of a coal mine. The average thickness of coal seams mined in the United States has changed very little in the past 40 years. The first measurement of thickness of bituminous coal and lignite seams was made for 1920, when the average thickness was 5.3 feet.2 The average thickness for later years was as follows: 1945, 5.4 feet; 1950, 5.3 feet; 1955, 5.2 feet; 1960, 5.3 feet; and 1965, 5.2 feet.3 Table 1 includes data on number and production of bituminous coal and lignite mines classified by 1-foot intervals of seam thickness mined in 1920, 1945, 1950, 1955, 1960, and 1965. Though bituminous coal and lignite are mined today from seams of exceedingly variable thickness--less than 2 feet to more than 50 feet--a large majority of the production, 62 percent in 1965, came from seams 3 to 6 feet thick. This is not surprising since the coal seam of moderate thickness presents the least mining difficulties.

Jan 1, 1967

By R. E. Campbell

Uranium metal of improved purity was prepared by electrorefining commercial magnesium-reduced uranium in a molten sodium chloride-uranium trichloride electrolyte. The best operating conditions for the preparation of refined metal were established as follows: an electrolyte containing 8.7 to 13.3 weight-percent uranium; initial cathode current densities from 300 to 1,500 amp/sq ft; and a molten salt temperature of 860° C. Ingots produced from electrorefined uranium crystals prepared with these operating conditions were substantially free of metallic impurities. The only impurities in the refined and consolidated metal were present in low or undetectable amounts.

Jan 1, 1965

By R. E. Morgan

[IN COMPILING the table of analyses of this bulletin every available source of information was studied. These sources, as listed at the end of the table, were many and varied, and it believed that the tabulation gives the best general information obtainable. However, its known accuracy and completeness of coverage necessarily fall far short of published data on coals of the United States. A table of world production of coal and lignite, as and published by the Bureau of Mine, of world resources of coals, brown coal, and lignite, as published in the Yearbook of the World Power Conference, 1948, are included for convenience of the reader. The six continental maps at the end of the bulletin show the general location of the principal coal fields.]

Jan 1, 1952

By T. N. McVay

The Bureau of Mines has developed a field test for detecting the presence of columbium in a variety of minerals containing the clement. The test consists of fusing the mineral or rock powder with potassium pyrosulfate in a porcelain crucible, digesting the melt with hot dilute hydrochloric acid to release the columbium oxide (Cb205), and subsequently reducing the columbium oxide to a lower oxide by adding tin, which gives a blue color to the contents of the crucible. The method will detect 1 percent of contained columbium oxide (Cb205) in a mineral sample provided no tungsten is present. If a mineral containing appreciable titanium is test,-!d in the same manner, the solution in the crucible becomes violet. In the presence of columbium, titanium at first causes a violet coloration of the solution, which after a few minutes is masked by the stronger blue of the reduced columbium oxide. Although tantalum oxide (Ta205) does not interfere with the columbium test, tungsten gives a blue color that is indistinguishable from the color obtained with columbium. A simple method is available to detect the presence of columbium in the absence of tungsten, but when the presence of tungsten is suspected, the sample must be subjected to somewhat more elaborate chemical tests to determine the presence or absence of columbium. Although these latter tests can be made in the field, several steps are involved that arc best performed in the laboratory with simple equipment.

Jan 1, 1962

By E. J. Lintner, J. R. Thoenen

During the period 1937-40 and until peacetime research was superseded in 1941 by wartime activities , the junior author was engaged in studies regarding the relative efficiency of operating methods in quarries producing crushed stone for mineral aggregates . The results of some of these studies were published as reports of investigations in 1939 and 1940 ; / others were discontinued due to war demands on personnel and time . The published reports discussed the efficiency of particular quarry operations with respect to the time consumed and without reference to costs or mechanical factors . • At the time , the field data were collected for the published reports other data were collected relative to the relationship of the numerous variable factors inherent in the operation of a churn drill to the ability of the drill to produce blast holes . The churn drill is essentially a crusher and depends. for its performance upon the foot-pounds of energy it can impart to the cutting edge of its bit . The gravity stamp mill , so well-known in western gold mines , is essentially the same type of crusher . The ratio of foot- pounds necessary to crush the rock , to the total theoretical energy developed by the falling churn- drill tools , affords a good means of evaluating the efficiency of the tool . This does not include to tal over-all efficiency involving the mechanical equipment of the drill itself or its power unit .

Jan 1, 1947

By Albert W. Deurbrouck

The performance of four sand cones was evaluated by the Bureau of Mines in three preparation plants that utilized cones in various flow schemes. The cone at plant A was a simple two-product one that provided clean coal and refuse. Plant B had two cones; one cone made a primary separation and the other a secondary separation. The primary cone separated salable coal from heavy rejects. The secondary cone separated a low-ash metallurgical coal and an intermediate-ash product suitable for plant fuel or steam markets. In plant C the sand cone was equipped with a middlings draw Which continually removed an intermediate specific-gravity product below the surface of the cone. The three primary separations of raw coal effected between floats and sinks were excellent. The recovery efficiencies for the plus 1/4-inch material ranged from 99.8 to 97.6 percent, the error areas ranged from 19 to 23 square centimeters, and the probable errors in specific gravity ranged from 0.033 to 0.024. The performance data of the two secondary separations varied from excellent in plant B, where the separation was on a par with the primary separations, to somewhat inferior in plant C, where the secondary separation was effected at the middlings draw.

Jan 1, 1965

By Albert W. Deurbrouck

The preparation characteristics of the coals of Buchanan County, Va., are described in this Bureau of Mines report. Twenty-one samples ,,,ere collected from 9 coalbeds in the county. Of these samples 13 were of metallurgical quality as received, and 8 required some upgrading to provide acceptable products. In general, the coals were of low to medium ash and sulfur content, and ranked as medium-to high-volatile bituminous. In 1963, production in the county was in excess of 13 million tons, of which 2.2 million tons were mechanically cleaned.

Jan 1, 1966

By George F. Dana

Oil yields, lithology, and stratigraphy have been evaluated for 15 cored wells and two sampled wells representing 10 square miles of the Tipton Member of the Green River Formation near Green River, Wyo. The area evaluated is being used by the Bureau of Mines for experimental production of oil from the oil shales in place. Lithology and oil yields were correlated to produce a stratigraphy diagram for the in situ study area, permitting precise designation of comparable sections. Because of lateral uniformity of oil shale, oil yields from eight cores and two sets of drill-cutting samples within a quarter section show the range of variation in average oil yield arising from experimental error. Variation in average oil yields from the seven cores representing the 10-square-mile study area lies within the expected experimental error. No difference in oil-shale richness across the study area is indicated. Average oil yields for three Tipton sections in the study area were deter-mined as follows: (1) The entire Tipton Member oil shale (about 145 feet thick), 13.3 gallons per ton; (2) the 40-foot upper rich zone, 21.0 gallons per ton; and (3) the 21-foot zone in which the Laramie Energy Research Center is conducting in situ experiments, 22.4 gallons per ton. One acre of the 21-foot experimental section represents 34,300 barrels of oil in place, and 1 acre of the Tipton's 40-foot rich upper layer represents 62,000 barrels.

Jan 1, 1972

By A. J. Kraemer

This report on the physical and chemical properties of typical crude oils of California is the 'eighth in a series on the producing districts of the United States. It includes discussion of results, tabulated data, and individual analyses of typical California crudes. Additional analyses of crude oils from the fields of Fresno, Kern, Los Angeles, Orange, end Ventura Counties will be published later in another Serial of the Bureau, but the summary tabulations are presented here. The samples represented in this report were collected over a rather wide interval of tine, the early samples having been obtained during the fall of 1919, and the most recent ones dating from the summer of 1923. It is thought that the samples are fairly representative, both of the older settled production and of the new flush production of the southern California fields.

Jan 1, 1924