Search Documents

By Paul B. Harder

Round Mountain Gold (RMG) in central Nevada, reports that over a nine-year period and a million operating hours, its fleet of 150-ton and 190-ton haul trucks has averaged better than 93% availability, with some of the trucks approaching 70,000 operating hours. Repair costs have been far below industry averages. Mine operations manager Pete Kesl credits the high availability and low repair costs to a succession of Product Support Agreements between RMG and Caterpillar dealer Cashman Equipment. He adds that good equipment and a high level of trust and co­operation between all parties to these agreements have been essential to their success at Round Mountain.

Jan 1, 1998

By L. C. IlsLey

[The last previous Bureau of Mines publication relative to details of permissible methane detectors (Bulletin 331, published in 1930) describes detectors of four different types, namely flame, combustion, catalytic, and a combination Wheatstone-bridge axed catalytic type in which catalytic action at the surface of a platinum filament when in methane causes a change in the temperature and resistance of the filament, thus unbalancing the bridge circuit and giving a reading proportional to the methane concentration. Three detectors of the latter type have been approved since 1933. A brief description of each follows: U. C. C. Detector Approved No. 902, covering the U. C. C. indicating detector, as described in Bulletin 331, was entered January 27, 1330, to cover important chances in design that permit checking; the calibration of the detector at any time, whether in gas or fresh air. Essential features of the detector are shown in figure 1.]

Jan 1, 1937

By Jr. Driscoll

The thermoelectric properties of yttrium monoarsenide, yttrium monoanti-monide) and ternary materials from the Y-As-Se and Y-Sb-Te systems were investigated by the Bureau of Mines from room temperature to 1,000° C. The maximum calculated figure of merit for yttrium monoarsenide and yttrium monoantimonide was 2 x 10-5 ° C-1. YAs and YSb were semimetallic conductors with low Seebeck coefficients and electrical resistivities. The values of the Seebeck coefficient and electrical resistivity of the Y-As-Se and Y-Sb-Te materials were between those of the yttrium selenides and tellurides and of YAs and YSb, respectively. The maximum power factor calculated for the Y-As-Se materials was 2 X 10-5 watt/cm ° C2 which yielded an estimated figure of merit of 6 X 10-4 0 C-1. Most of the Y-As-Se compounds had high Seebeck coefficients and moderately low electrical resistivities. The Y-Sb-Te materials were degenerate semiconductors with power factors of 6 X 10-8 watt/cm ° C2.

Jan 1, 1967

By Edward L. McHugh, Charles Sabine, Jami Dwyer, David G. Long

Slope failure accidents were responsible for about 12% of U.S. surface mine fatalities between 1995 and 2003. Small surface movements on a mine highwall may be precursors of failure that, if detected, could provide sufficient warning to enable workers and machinery to be withdrawn to safety. Radar interferometry offers the necessary precision to detect these movements. Radar has some advantages over other methods in its ability to cover large surface areas for true two-dimensional monitoring day and night under almost any weather condition. Radar’s active transmit/receive mode of operation provides for more direct sampling than do passive optical methods that depend on solar illumination. Improvements in microprocessor speeds and capacities have led to the development of a number of small, portable, ground-based systems; such systems are now being deployed at several locations around the world. As part of an ongoing study of monitoring technologies, researchers from the National Institute for Occupational Safety and Health and Brigham Young University, Provo, UT, cooperated to assess the feasibility of using interferometric radar to monitor mine slope stability. Field tests of a device incorporating prototype equipment were successful in that small, centimeter-scale displacements on rock slopes were detected.

Jan 4, 2006

By J. M. Kuchta

The Bureau of Mines used laminar hot air jets of l/8- to 3/4-inch diam-eter to determine the hot gas ignition temperatures of various combustible vapor-air mixtures. The combustibles were n-hexane, n-octane, n-decane, a hydrocarbon jet fuel (JP-6), and an adipate ester aircraft engine oil (MIL-L- 7808). Minimum ignition temperatures occurred at a fuel to air weight ratio of about 0.5 and were not greatly sensitive to variations of fuel concentra¬tion. Moderate variations of jet velocity also had little influence on these ignition temperatures. However, these temperatures decreased with increase in heat source dimensions (jet diameter). The hot gas ignition temperatures of the combustibles were not necessarily much greater than corresponding autoignition and wire ignition temperatures when the size (,F the heat source and the ignition criterion were the same.

Jan 1, 1966

By Robert F. Chaken

The National Institute of Occupational Safety and Health (NIOSH) is dedicated to achieving "safety and health at work for all people -- through research and prevention." An important procedure in pursuing this goal is the NIOSH surveillance studies where the number of injuries are monitored according to demographic, employment, and injury characteristics. These numeric data are then used to identify injury risk factors, develop safety programs, and monitor implemented remediation methods. In essence, ongoing surveillance data form the bases for directing the resources of NIOSH in setting of research and prevention priorities, and in evaluating safety procedures. This surveillance techmque, which is based on the Public Health Service approach to identification and control of disease (1, 2, has been used quite successfully in dealing with relatively high number injuries such as hearing loss, musculoskeletal disorder, respiratory disorder, falls, etc. (2). However a problem arises when extending this paradigm to lower frequency traumatic events; particularly those often referred to as disasters (i.e., high impact events like mine explosions, airplane crashes, etc.). One can ask the question - there hasn't been a coal mine fire fatality in the U.S. for over ten years, to what extent should we be concerned with mine fire safety (resource-wise)? - The National Traumatic Occupational Fatalities (NTOF) system (4J which NIOSH uses to survey occupational fatalities annually, would suggest that underground mine fires would not be a high priority item in occupational safety. Yet, miners' (i.e., the exposed workers) do consider mine fires and explosions to be major safety concerns. I believe that we need to rethink our evaluation of work place disasters, what is worker exposure, and what are the underlying assumptions (both explicit and implicit) as to the impact that economic, societal and degree of hazard factors make on risk evaluation. The answers to all these problems, will require much broader considerations than those in current surveillance safety and health models. This paper discusses some facets of those considerations.

From the National institute for Occupational Safety and Health Disasters take many forms and demand quick response from emergency workers. They may include natural disasters such as earthquakes or hurricanes, or they may involve manmade disasters such as technological failures or terrorist attacks. As a member of an emergency response team, you and your team members are at risk of experiencing what psychologists refer to as a traumatic incident—an incident that may Involve exposure to catastrophic events, severely injured children or adults, dead bodies or body parts, or the loss of colleagues, for instance. Traumatic incidents can produce unusually strong emotional reactions that may interfere with your ability to function at the scene or later: You may experience any of the physical, cognitive, emotional, or behavioral symptoms listed below in Table 1. Some people experience emotional aftershocks weeks or months after they have passed through a traumatic event. Others may experience these reactions while still at the scene, where they must stay clearly focused on constantly changing hazards to maintain their own safety and to rescue injured victims.

To suppress the natural bacterial action in acid mine drainage (AMD), the major contributor to acid formation. Approach Recycle partially-treated affluent back to the source of AMD within a mine, or to the coal or coal-waste stockpile. This effectively eliminates any further biologically-promoted AMD by inhibiting catalyzed weathering or oxidation by acid-forming bacteria. How it Works AMO-type effluents can be largely reduced by "recycling" the acidic outflow back to the source of AMD within a mine or to the Input side of a waste pile to percolate through the reactive pyrite and bacteria mixture. The bacteria in the cell thrive on the oxidation of ferrous to ferric iron through the electron transfer, Fe2 +[=]Fe3 + + e. Its reaction product [s, therefore, essentially ferric iron. While small quantities of Fe3 + will not interfere with the exponential multiplication of the bacteria

Jan 1, 1982

By Vern L. Kegler

This paper is one off a series dealing with mining methods and costs, sponsored and published by the United States bureau of Mines. ACKNOWLEDGMENTS The author acknowledges the, constructive and helpful suggestions and criticism of W. F. Lamoreaux, vice-president, and general manager of the Ducktown Chemical & Iron Co. United States Geological Survey Professional Paper- 139, by W. H. Emmons and F. B. Laney, has been drawn upon for some of the information contained in the paragraphs or history and geology.

Jan 1, 1931

By Robert C. Steckley

The Bureau of Mines performed a fragmentation experiment in cooperation with Duval Corporation in a porphyry copper-molybdenum deposit near the Sierrita pit south of Tucson, Ariz. This experiment evaluated the fragmentation created in a 10-hole test blast having blasthole spacings of 25, 20, and 15 feet. The 10 blastholes were 9 inches in diameter and contained a total of 17,400 pounds of aluminized slurry blasting agent in 50-foot columns with 60 feet of stemming. Diamond drill core examination was the primary method used to determine the condition of the rock before and after blasting. These core examinations included study of length recovery, rock quality designation (RQD), weight recovery, and size distribution. Topographic surveys were used to measure the rock swell produced by the blast and a fragment size distribution was obtained for the broken material on the surface. Fragmentation to depths of 110 feet was excellent from the 15-to 20-foot blasthole spacing patterns. Good breakage was also produced by the 25-foot pattern although the effects of the blast were not so obvious. In situ leaching tests were not conducted. However, based only on size consideration, all three blasting patterns produced adequate breakage for successful leaching.

Jan 1, 1975

By G. S. Rice, H. P. Greenwald, H. C. Howarth

"Stoppings in coal mines serve, important and. vital functions, such as coursing the ventilating current, sealing off abandoned or dangerous workings, sealing fire areas, and separating mines at boundaries. Stoppings may hold back water, but normally that is not their function; their design is, or should be very different from that of a hydraulic dap which is designed to a definite load, often a very heavy one, from one direction over an indefinitely long period. Hence, a dam usually requires an arched structure to resist hydraulic pressure, and it must be massive to meet vertical stresses due to heavy ground pressure.Stoppings are designed primarily to resist a pressure applied laterally through air or gases. Their strength cannot be stated without specifying the direction of applied load. A stopping may be placed in stress by proof pressure subsequent to erection, through extraction of pillars in the vicinity which may act direct, or by squeezing the ribs or heaving the floor. These forces act more or less parallel to the faces of the stopping and may be very great but measures must be taken suitable to each case, and it is impossible to allow for these in general specifications other than to call for normally good construction. A stopping is principally designed to resist the action of forces at right angles to its face, such as the shocks of blasting, the pressure of gas from instantaneous violent out bursts such as have occurred in certain British Columbia coal mines, sudden compression of the air by great falls of roof in closed spaces, and at time pressures that accompany an explosion of either fire damp or coal dust or both. This paper deals with the tests of pressures of explosions only."

Sep 1, 1930

By Theodore Christos

The Bureau of Mines sponsored an investigation of the thermal oxidative degradation characteristics of selected ingredients employed in the formulation and manufacture of conveyor belts. This work was done to supplement similar studies of samples from finished conveyor belts and thus provide basic data for correlation of the potential toxic behavior of a finished belt with that of the individual ingredients. This report covers the study of (1) basic polymers (styrene-butadiene, neoprene), (2) reinforcing fibers (Nylon 6,6, Dacron, viscose rayon), (3) flame-retardant plasticizers (tritolyl phosphate-isomeric mixture, tri-p-tolyl phosphate, tributyl phosphate, tris (dichloropropyl) phosphate), (4) plasticizers (diphenylphtha1ate, di-(2-ethylhexyl) sebacate), and (5) a vulcanization accelerator (2-mercaptobenzothiazole).

Jan 1, 1977

By James H. Russell

The Bureau of Mines, U.S. Department of the Interior, in cooperation with the Department of Energy, has attempted to increase the activity of nickel catalysts for converting synthesis gas, derived from coal, to a substitute natural gas. This report describes the effects of low-level additions of B, Ca, Ce, Co, Mn, Mo, Pd, Re, Ti, Y, Zn, and Zr on the methanation activity of Raney nickel. The methanation rate at 320° C and the resistance to poisoning by 2 ppm H2S were used to compare catalysts. The effects of the additions were small, and the experimental variances were large, necessitating the use of statistical methods to identify significant effects. Co, Ti, Y, and Zn improved the resistance to H2S poisoning, but only Co improved the methanation rate In some individual catalysts containing Ca, Mo, or Mn, both the methanation rate and resistance to H2S poisoning were improved.

Jan 1, 1980

By Russell E. Griffin

Dielectric constants and dissipation factors were measured for six rocks over the 20-to 100-megahertz frequency range by means of the susceptance-variation method. Results for both dry and moist specimens are presented and compared with data reported by others. Loss factors calculated from the data presented are important to the Bureau's study of rock fragmentation by means of dielectric heating.

Jan 1, 1967

By J. Douglas Causey

In 1986, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied the 7,940-acre Southern Otay Mountain Wilderness Study Area (CA-060-029), and the 5,750-acre Western Otay Mountain Wilderness Study Area (CA-060-028) in order to evaluate their mineral resources. The wilderness study areas are located in San Diego County, CA, about 20 miles southeast of San Diego. No mineral resources were identified in the Southern or Western Otay Mountain Wilderness Study Areas, based on literature, field observations, and sample results. The wilderness study areas are underlain by a complex blend of Late Jurassic, moderately metamorphosed sedimentary and volcanic rocks. Evidence of mineralization is not obvious.

Jan 1, 1987

By Irving Hartmann

Modern mechanized mining with high-speed machines, multiple-entry systems, multiple blasting, high-velocity air currents, and rapid haulage has brought many economic benefits and has on the whole enhanced safety in the coal-mining industry. It has, however, also introduced some added hazards, the control of which requires concerted effort and ingenuity. Mechanized mining has greatly increased the production and dissemination of fine coal seam or in mine entries. Use of high-speed machines has increased the probability of formation of incendive sparks, which are produced by frictional contact between moving metals and certain mineral substances in the coal seam or in the adjoining rock strata. In gassy seams rapid extraction of coal has increased the rate of gas evolution. These facts have made more urgent the need of preventing the ignition of coal dust and the development of widespread mine explosions. The ignition hazard can be controlled best by eliminating all potential igniting sources and by careful attention to ventilation designed to prevent accumulation of gas capable of triggering a coal-dust explosion. Frictional spark ignition by mining machines and suggested safeguards are discussed in a recent publication. Extensive research and long experience have shown conclusively that the propagation of coal-dust flames can be arrested and the development of widespread explosions prevented by properly applied, generalized rock dusting.

Jan 1, 1956

By J. I. Paige

The effect of fluoride inclusions on the properties of titanium produced from the Bureau of Mines developed induction slag melting process is of concern to members of the titanium industry. The objective of the research was to determine the effect of CaF2 inclusions on the properties of titanium and its survival rate during melting. The data were obtained from single induction-slag-melted ingots prepared with the normal addition of 4 pct and also with 2- and 1-pct additions of CaF2 slag. The results of this effort showed that the mechanical properties of single-induction-slag-melted Ti-6Al-4V alloy exceed the minimum values specified in Aerospace Materials Specification for Titanium Alloy Bars and Forgings AMS4928H, but these materials are much more notch sensitive in fatigue than normal Ti-6A1-4V alloy titanium. First and second vacuum-arc remelts of single-induction-slag-melted ingots fragmented and increased the number of inclusions, while reductions in the amount of flux resulted in an upward trend in the spatial distance between pores in an x-y plane.

Jan 1, 1988

By B. J. Moore

This Bureau of Mines publication reviews U.S. helium resources as of January 1, 1973. These resources, estimated to be 693.7 billion cubic feet, are broken down into four classifications, as follows: helium in storage, 34.9 billion cubic feet; helium in measured helium-rich natural gas reserves, 119.5 billion cubic feet; helium in measured helium-lean natural gas reserves, 62.8 billion cubic feet; and helium in indicated or undiscovered natural gas resources, 476.5 billion cubic feet. The helium in undiscovered natural gas is considered a national resource; however, this gas may not be discovered depending on many factors beyond the scope of this paper, and most of the helium in natural gas will be dissipated as the gas is consumed for fuel and other purposes.

Jan 1, 1976

By Lulie H. Crump

U.S. supply and demand data for dry natural gas by source, form, and major consuming sectors--within and between States and defined regions--were tabulated for the years 1960 and 1965. State-by-State quantitative data are provided for the natural gas industry that can be arranged into regional groupings and used to determine regional flow patterns. The tables show the derivation of the total supply of gas available for consumption from total marketed production. The tables also report the distribution of the supply among the major consuming sectors (household and commercial, industrial, transportation, and electricity generation, utilities). The summarized data show an increase in the absolute demand for natural gas in all regions for the period 1960-65, although the relative posit ions of the various subregions, with respect to national consumption, remained about the same. To enable comparison of data on dry natural gas with data on other energy sources, quantities in terms of million cubic feet were converted to British thermal unit (Btu) equivalents.

Jan 1, 1969

By D. W. Frommer, M. M. Fine

Laboratory investigations have produced flotation concentrates contain- ing 91 to more than 92 percent titania, with fair recoveries, from the Christy property, Hot Spring County, Ark. The titanium-bearing ore on the Christy property occurs in a quartz-clay- iron oxide mineralization, which contains, on the average, about 6.0 percent TiO2, chiefly as the mineral brockite; brookite and rutile are different crys- talline forms of titanium dioxide. Recent work by the Bureau of Mines has shown that titanium chloride can be produced readily from the rutile-type mineral by reduction with coke fol- lowed by low-temperature chlorination. Metallic titanium is in turn derived etallic from the chloride by the Kroll process .

Mar 1, 1952