Search Documents

By Seth C. Schaefer

The Bureau of mines investigated thermodynamic properties of MnSO4 and 2CdO CdSO4 to obtain basic thermodynamic data applicable to the treatment of mineral concentrates during roasting and sintering processes. Standard Gibbs energies of formation were determined with high-temperature galvanic cells using stabilized Zr02 as the electrolyte. Potential measurements were obtained from the cells?

Jan 1, 1983

By R. E. Kennedy

The presence in air of combustible cases and vapors can constitute an extremely serious explosion hazard. This hazard is even greater when explosive mixtures are confined under high pressures, as the pressure can become tremendous immediately before the container is ruptured. Because of its interest in safety in mining and allied industries, the Federal Bureau of Mines has investigated the flammability (explosibility) of various types of combustible atmospheres and has published Its findings. 4/ The explosibility of ethane has been studied, and its limits of flammability have been determined and published. The development of secondary recovery methods of stimulating oil production has intensified interest in the effect of high pressure on the explosibility of natural gas-air mixtures. The limits of flammability of natural gas-air mixtures at pressures ranging from 50 mm. Hg to 350 p.s.i.a. have been determined and published. More recently, the limits have been determined at pressures up to 3,00C p.s.i. in mixtures of natural gas-air-nitrogen.

Jan 1, 1950

By W. D. Mcmillan

The Dempsey tract in Washington County, Mo., had a small production of lead-zinc ore from shallow workings. Old dumps from early-day lead mining contain about 25,000 tons of ore averaging about 3 percent combined zinc and lead. Because of the urgent war requirements for lead and zinc, the Dempsey property was examined by Otto Ruhl, formerly an engineer of the Bureau of Mines in August 1942 and selected for further investigation by churn drilling twenty holes totaling 1,309 feet were bored in the fall of 1943. The results of the work are presented in this paper.

Jan 1, 1948

By Joseph C. Zelanko, Christopher Mark

During August, two eastern Kentucky coal miners died in a roof fall during retreat mining operations. They had just finished extracting one pillar block and were moving to the next one when the intersection they were standing in collapsed. Regrettably, this was not an isolated incident. Since the end of 2000, there have been 28 ground fall fatalities in U.S. coal mines. Of these, 10 occurred during pillar recovery operations. Although pillar recovery has been associated with about one third of recent ground fall fatalities, it accounts for only about 10% of U.S. underground coal production. Statistically, a coal miner engaged in pillar recovery is several times more likely to be killed in a ground fall than a miner on an advancing section of a longwall. Pillar recovery is dangerous because it creates an inherently unstable situation. Once the pillars are extracted, the roof is expected to cave. Safe pillar recovery does not mean preventing roof collapse, it means ensuring that it only occurs after the miners have completed their work and have left the area. Fortunately, there are a number of proven techniques that can greatty reduce the hazards of pillar recovery. These include better mine planning, improved roof support, and safer work procedures. The goal of this article is to describe the most significant "risk factors" associated with pillar recovery, and prescribe control techniques that, taken together, can reduce the overall risk to miners. The conclusions are based on extensive studies conducted by the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) that have included detailed analysis of every fatal retreat mining incident since 1992 (25 incidents resulting in 30 fatalities). Risk reduction strategies for pillar recovery can be divided into three main groups: Global Stability: Prevention of section- wide pillar failure; Local Stability: Prevention of roof falls in the working area; and Work procedures and worker location: Minimizing exposure to hazardous areas.

By Albert J. Forney

Extensive studies have been made of the various effluents found in the Synthane coal-to-gas process. Analyses have been made of the waters, gases, and trace elements present in some of the streams. Results of analyses show the water effluents are the area where extensive research is needed.

Jan 1, 1974

By Joseph A. Sutton, John D. Corrick

The chemistry involved in the microbial dissolution of iron and copper from such sulfide minerals as pyrite, chalcopyrite, chalcocite, cove11ite, and bornite is described. The chemical criteria used to evaluate the activity of microorganisms on these minerals were changes in pH, ferric iron produced, and oxygen consumption. In a series of experiments in which a ferrous sulfate nutrient solution was percolated over small portions of the above-mentioned copper sulfide minerals for 56 days, the iron-oxidizing bacteria Ferrobaci11us ferrooxidans and Thiobaci11us ferrooxidans were capable of bringing about the dissolution of 23.7 percent of the copper from chalcocite, 56.3 percent of the copper from cove11ite, and 29.8 percent of the copper from bornite by the microbial production of ferric sulfate which reacted with these minerals. Laboratory tests have demonstrated that pure strains of the iron-oxidizing bacteria act as catalysts to the ferrous iron being oxidized by the Oxygen of a system containing pyrite and chalcopyrite. In a series of experiments during which nutrient solution was percolated over pyrite for 70 days, the ferric iron produced by the iron-oxidizing bacteria was 112 to 120 times greater than that produced atmospherically.

Jan 1, 1964

By Arne Landsberg

The Bureau of Mines measured the vapor pressure of FeC12 , FeBr2, FeI2, Sb, Bi, Cd, Mg, Pb, FeC13 , and VCl2 using the Knudsen-and torsion-effusion methods, and on FeC13 -NaC1 mixtures, Au2Cl6, and MgNi2 using only the Knudsen method. Apparent vapor pressures calculated from the experimental data vary with orifice size and method of determination. Reaction with residual oxygen in the instruments was noted to have an effect on the iron halide data. Vapor pressure curves plotted as log P versus 1/T (where P is pressure and T is absolute temperature) for one substance using several orifice sizes tended to converge at a single point when extrapolated beyond the experimental region. All of the data, except those of VC12, agree with previously published results. The importance of comparing effusion measurements with those obtained by other methods and the variations encountered with various orifice sizes are discussed.

Jan 1, 1977

By Holmes, George H. Jr.

The Cherry Creek tungsten district was explored by the Bureau of Mines from April 16 to August 13, 1942. This district is in north-central White Pine County, Nev., 50 miles north of Ely. Principal work was done on the property of the Cherry Creek Tungsten Mining Co. and at the adjacent Chance mine, although the entire district was examined and mapped. The exploratory work was done in cooperation with the Federal Geological Survey and comprised surveying, trenching, sampling, long-hole and core drilling, rehabilitation of mine workings, road building, drifting, and shaft sinking. The more important tungsten occurrences were explored by trenching and diamond drilling. Sixteen holes, having a total length of 2,515 feet, were drilled. The project resulted in partial development of three new tungsten deposits and small increases in the reserve tonnage of two scheelite-bearing lenses that were being mined by the company. The following pages summarize the history of the district, outline the ownership of the properties explored, and describe the physical features and mineral deposits. Mining and milling practices at the Cherry Creek tungsten mine are outlined, and the plan and results of project work are presented in detail together with surface maps, assay maps, and drill-hole logs.

Jan 1, 1950

By B. Numerov

A numerical proceeding of corrections with respect to topography is worked out for places near the station and a graphical one for the remote parts of the terrain. The description is clear and very detailed. The numerical proceeding is very similar to that of the Eötvös and Schweydar methods which are in use already. In both methods the levelling is accomplished in certain circles and fixed azimuths around the station. While, in using the Eötvös method, the height differences are directly inserted into the final formulas with regard to the foot of the instrument and in case of accurate formulas derived by Schweydar the height differences are calculated with respect to the center of gravity of the attachment, Numerov introduces functions A and B, the heights, of the terrain and of the center of gravity, which are to be inserted into the formulas.

Jan 1, 1929

By Robert S. Warfield

The Federal Bureau of mines and U.S. Geological Survey conducted exploratory investigations and geologic mapping in the Wishbone Hill district of the Matanuska coalfield almost continuously from 1942 through 1958. These investigations delineated reserves of high-volatile bituminous coal necessary to supply the rapidly expanding military and civilian requirements in the Anchorage area. This report describes the program conducted by the Bureau of Mines from 1949 through 1958, and briefly summarizes previous investigations, the results of which have already been published. The coal-bearing structure on both the north and south limbs of the prominent Wishbone Hill syncline was explored by 8,719 feet of churn drilling and 25,460 feet of diamond-core drilling. A total of 33 holes were drilled ranging in depth from 60 to 2,114 feet. To supplement the drilling operations, bulldozer and dragline trenching were undertaken at key locations; about 25,000 cubic yards of dragline trench were excavated in the vicinity of the old Premier mine.

Jan 1, 1962

By Raymond W. Hiteshue, Sam Friedman, Martin D. Schlesinger

The Bureau of Mines in cooperation with the El Paso Natural Gas Co. investigated the effect of high temperature and pressure at short residence times on the hydrogenation of a New Mexico coal to gaseous and liquid hydrocarbons . The study was made in a bench - scale semicontinuous unit at pressures of 500 to 6,000 psig , 480 ° to 1,000 ° C , and residence times of less than 1 minute to 15 minutes . Ammonium heptamolybdate was impregnated on the coal to furnish 1 percent molybdenum based on maf coal . Coal could be rapidly hydrogenated at elevated temperatures and pressures to yield large quantities of gaseous hydrocarbons and small quantities of lowboiling oils , high in single - ring aromatics . At 800 ° C and 6,000 psig and a residence time of 1 minute , the yield of hydrocarbon gas was 43 percent and of liquid hydrocarbons 9 percent , based on maf coal . With a 15 - minute residence time , the yield of gaseous hydrocarbons increased to 68 percent with a decrease in yield of oil to 6 percent . At higher hydrogen velocities , the yields of oil were much greater but contained large quantities of asphaltene . Low concentrations of molybdenum (0.01 and 0.1 percent ) or a high concentration of iron ( 1 percent ) were ineffective at 800 ° C , 6,000 psig , and short residence time .

Jan 1, 1964

By John Neil, John Bli ard

Coke breeze consists of the smaller particles of coke formed by handling coke on and after removal from the ovens. Its value as F, fuel is less than that of the larger pieces, both because the smaller pieces contain more ash and therefore have a lower calorific value, and because a greater draft is required to burn it.The tests described below show its value as a fuel when mixed with bituminous coal and burned in a hand fired boiler of a size considerably greater than that used in an ordinary house. The results of these tests, however, can be used to give a fairly good indication of the value of coke breeze when burned with bituminous coal in a domestic furnace.All who fire a domestic furnace know that for only a comparatively short part of the day, and then only on a few days, is it necessary to open fully the ash, pit door and stack damper to get the required rate of combustion in the average furnace in the average house. It will be practical, therefore, during the greater part of the heating season, to fire coke breeze with the coal and use more of the available draftsFor domestic heating the coke breeze should be stored separately, and used when the draft is sufficient to burn it in mixture with bituminous coal, at the rate required to warm the house.Purpose of tests: The tests were carried out at the request of the Chamber of Commerce of Pittsburgh, Pa., in order to determine the steaming value of coke breeze as a fuel when mired with Pittsburgh coal and fired by hand, and to see whether the mixture when burnt would give off an objectionable quantity of make.

May 1, 1921

By J. D. Davis

On May 15, 1936, Congress authorized the Bureau of Mines to conduct certain studies, experiments, and investigations of subbituminous coal and lignite .4/ Appropriations were made in July 1937, and since that date an active investigation has been underway to complete the provisions of the act. Part of the investigation has included a comprehensive survey of the known properties of the lower-rank non-coking coals, and provisions were made to obtain more data on certain varieties. In line with this plan, a typically subbituminous coal was selected for an extended series o tests in the standard Bureau of Mines-American Gas Association unit,5/ at the Central Experiment Station. This particular noncaking coal was the first one of its rank that ha& been tested in the apparatus; for this reason the results are of particular interest because the testing apparatus was originally designed for use in studying the coke- and gas-making properties of coking coals. The test as described below has been developed by the Bureau of Mines since 1927 through a cooperative agreement with the American Gas Association.6/ Ninety to 180 pounds of coal is heated in a circular retort, 13 to 18 inches in diameter, at wall. temperatures ranging from 540°C. to 1,110°C. in 100°C. steps. All products axe collected and measured; their physical and chemical properties axe then carefully determined to ascertain the gas- and coke-making properties of the coal.

Jan 1, 1939

By M. E. Tyrrell

The Bureau of Mines produced building brick of good quality in an investigation designed to explore the possible utilization of high-glass fractions of municipal incinerator residues in the manufacture of building products. Common clays, lime, and sodium silicate were used as binders for the nonplastic residues Test bricks were formed by dry-pressing, soft-mud molding, and stiff-mud extrusion. A run of standard-size face brick dry-pressed and fired in the West Virginia University Coal Research Bureau pilot plant demonstrated that SW-grade glass-clay face brick can be produced on a commercial scale without difficulty. A cost evaluation made for production of the brick showed an estimated cost of $42.13 per thousand bricks for a shuttle kiln plant and $28.70 per thousand for a tunnel kiln plant.

Jan 1, 1972

By James J. Dowd

The investigation to evaluate the reserves of coking coal is being made by the Bureau of Mines in three parts: (1) To estimate known measured and indicated recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coal and coal blends not now widely used for metallurgical coke making. This is the tenth of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Knott County, Ky., which comprises parts of the Salyersville, Prestonsburg, Troublesome, Hindman, Pikeville, Cornettsville, and Whitesburg quadrangles. (See fig. 1.) A base map for each bed in each quadrangle was made to the scale 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds up to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick. These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and category, mined-out areas, areas excluded from the estimate but which may contain reserves based only on geologic inference, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1952

By Richard L. Unger

Equipment is the primary cause of injury in 11% of all mining accidents and a secondary cause in another 10%. Purchasers should select new equipment carefully to ensure that the machine incorporates good ergonomic design criteria that maximize the safety of their mine workers. One potential problem area is the workstation-the control center of the machine. Safety problems often occur when the workstation provides insufficient clearance or visibility to the operator or has controls that are difficult to reach. This is especially true for underground mines, where confined space is an issue. In reclined or stooped postures, operators will have less strength and agility and often experience reduced visibility. We have conducted and published much research in Human Factors design of mining machine workstations. This information is currently being compiled into a series of Human Factors design recommendation reports. The reposts dl cover many topics, including workstation layout, control design, seating, and visibility. Each topic has a list of basic or first principles of design. Understanding these principles is the key to designing or purchasing a workstation that is both safe and efficient. Following is a sampling of these main topics and first principles.

Aug 1, 1996

By James F. Devine

This Bureau of Mines report describes tests conducted at three sites to determine if, and to what extent, a vertical presplit fracture plane placed between a blast point and detection point will reduce vibration levels. Statistical analyses indicate that the presplit fracture plane did not reduce the vibration level.

Jan 1, 1965

By Howard E. Parkinson

In 1969, new coal mine health and safety legislation was enacted in the United States. As a result of this legislation, the Department of Interior, Bureau of Mines has carried out communications research aimed at developing whole mine communications for increased safety and efficient operation. The research has advanced and many promising results are now being demonstrated to the mining industry. However, there remains a challenge to further improve wireless communications within the mine workings, and through the overburden above the workings. The objectives for future research and development will be discussed, together with the physical and operational constraints that new mine communication systems must face.

Jan 1, 1973

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the fifth of a series of reports giving the results of studies by countless under part (1) of the investigation. (See appendix.) This report covers Westmoreland County, Pa., which comprises parts of New Kensington, Freeport, Elders Ridge, Pittsburgh, Greensburg, Latrobe, New Florence, Johnstown, Brownsville, Connellsville, Donegal, and Somerset quadrangles. (See fig. 1.) A short resume" of the chemical and carbonizing properties of the coals are included. Data on the coal beds in this county were obtained from mining companies, land companies, individual landowners, and other sources of authentic information. A base map for each bed in each quadrangle was made to the scale 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds up to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick. These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1951

By d&apos, Dennis V. Andrea

The Bureau of Mines and El Paso Mining and Milling Co. conducted a cooperative in situ leaching research program at the Emerald Isle mine near Kingman, Ariz. The objective of this research was to develop in situ leaching methods for 200,000 tons of ore exposed in the pit bottom and also 3,000,000 tons of ore under 200 feet of overburden adjacent to the pit. The research included core drilling for fragmentation analysis, inplace permeability testing, seismic surveys, blasting tests, blast vibration measurements, inplace leaching, and ground water monitoring. A l5,000-ton test area in the pit bottom was blasted and leached inplace for 117 days. This successful test was followed by leaching 100,000 additional tons of unblasted pit bottom ore. Two test blasts, under 205 feet of overburden and extending to 290 feet, were detonated in an area near the open pit. The second blast was detonated because the first blast did not create adequate permeability for leaching. Pit bottom leaching was discontinued and the test area under 200 feet of overburden was not leached because the company terminated operations at the Emerald Isle mine. Based on the research completed, an expanded in situ leaching system was designed, but not implemented, to recover copper from a 1,500,000-ton area at the Emerald Isle mine.

Jan 1, 1977