Search Documents

By G. E. McElroy

[The purpose of this paper is to present type: of charts adapted to aid in the graphic solution of fan-performance problems of selection and operation, and to urge the adoption of similar charts by the National Association of Fan Manufactures as standard forms for presenting fan-performance data. As matters now stand, it is difficult for the average engineer to solve such problems because a large number of variables are involved, and performance data are not presented in a manner that permits their direct application to many problems encountered in practice. The performance of any centrifugal machine is determined not only by the machine itself but also by the fluid-flow system on which it operates. Actual performance of centrifugal fans is therefore a matter of the type, size, and speed of fan, on the one hand, anti of the relation of pressure to quantity of flow, as determined by the physical condition of the airway s: stem, on the other.]

Jan 1, 1936

By R. V. Lundquist

This report describes results of tests on the desilication of solutions resulting from the leaching of lime-soda sinters. Desilication was accomplished by heating the solutions in an autoclave. A liquor relatively free of silica was obtained after 30 minutes of heating at 200 p.s.i.g. in the presence of lime. The addition of lime improved desilication, but the rate and efficiency of desilication was effected by the quality of lime used. The optimum quantity of lime for effective desilication was about 6 grams per liter. A lesser quantity gave poorer desilication, and a greater quantity increased the alumina loss without improving desilication. The alumina loss was approximately proportional to the lime added. A complex structure, called artificial noselite in this report, was the only silica bearing compound detected in the desilication precipitate. Other compounds present were Ca(OH)2 (calcium hydroxide), CaCO3 (calcium carbonate), and Ca [A1(OH)6]2 (hydrated tricalcium aluminate). Sodium carbonate in the leach liquor retarded the formation of the calcium aluminate; hence it decreased the alumina lost to the precipitate. The extraction of alumina from aluminum silicate materials by the limestone soda-sinter process has been investigated by the Bureau of Mines for many years. The process consists of the following major operations: Blending the aluminum silicate with limestone and soda ash in such proportions that dicalcium silicate and sodium aluminate are formed on sintering; leaching the sinter in a carbonated caustic solution to extract the soluble alumina; purifying the leach liquor by the precipitation of soluble silica (this precipitate is designated desilication precipitate in this paper); precipitating alumina trihydrate from the purified liquors by carbonating with carbon dioxide gas; and calcining the trihydrate to alumina. Commercial grades of

Jan 1, 1962

By C. E. Armantrout, H. Kato, M. I. Copeland, M. Krug

The investigation of the nickel - gadolinium phase diagram was undertaken to determine the alloying behavior of these two metals . The data from meltingpoint determinations , thermal analyses , metallographic examinations , and X- ray diffraction analyses revealed a phase diagram with three eutectic points and seven intermetallic compounds . Very limited solubility of the phases in each other was observed . The five phases , Ni Gd , Ni , Gd , Ni Gd , Ni, Gd , and NiGd¸ , melted incongruently at about 1,300 ° , 1,270 ° , 1,180 ° , 1,070 ° , and 775 ° C , respectively . Ni Gd and NiGd melted congruently at approximately 1,550 ° and 980 ° C , respectively . Four of the compounds were determined to crystallize in the hexagonal system : Ni Gd , Ni Gd , Ni , Gd , and Ni Gd . Ni Gd was determined to be cubic and NiGd , orthorhombic . The crystal system of NiGd was not determined . The eutectic points occurred at 13 , 67 , and 85 wt pct gadolinium , and the isotherms at 1,290 ° , 890 ° , and 700 ° C , respectively .

Jan 1, 1964

By G. W. Weems

The specific objective of this investigation was to determine the compressibility factors for helium and carbon dioxide mixtures at -10° and -20° C and pressures to 1,000 psia. A Burnett apparatus was used. Data from the experiments were treated by the method of Barieau and Dalton. Tables of compressibility factors and approximations of the virial coefficients are presented for 10 binary mixtures as well as for helium and carbon dioxide. The results follow the same trend as data previously reported.

Jan 1, 1970

By S. H. Ash

THE INUNDATION of anthracite reserves in the Eastern Middle field of Pennsylvania affects the life of the anthracite industry in this field; it also influences the economic status of people, communities, and industries that depend wholly or in part upon anthracite for their livelihood. The trends of production and of employment in the anthracite-mining industry in this field are downward, and they probably will continue in this direction. The reserves have been depleted to the extent that the end of the active life of the industry as a. major economic factor is approaching. By removing the water in those pools where it can be done economically, the future of this industry may be extended somewhat.

Jan 1, 1950

By E. W. Dean

This report on the physical and chemical properties of typical crude oils of Oklahoma is the sixth in a series of preliminary chapters of a bulletin covering the producing districts of the United. States. Preceding reports* may be obtained on request. The details of the methods used in this survey in collecting samples, making laboratory tests, and interpreting results are discussed in the first three papers. If any errors or omissions are noted by readers, it is hoped they will be brought to the attention of the Bureau of Mines for correction before the appearance of the permanent report. Samples of Oklahoma crudes analyzed in this report were taken from those fields representing the major production of the State. The Oklahoma Geological Survey designates 172 different oil and gas fields in the State, S1 being in Osage County, 14 in Tulsa County, 14 in Okmulgee County, 9 in Washington County. The list of samples collected by the Bureau of Mines represents only 5 fields in Osage County - Bigheart, Burbank, Hominy, Osage Junction, and Pershing - yet these samples, together with those from adjoining fields, are representative of nearly all crude produced in the county. The sample 'from the Pershing field, for example, is representative of the crude produced in several fields in that part of the county - such as Nelagoney, Pawhuska, Wyomona - and the sample from the Skiatook,

Jan 1, 1922

By Fred N. Kissell

In This Chapter [Early indicators of a gas problem How the methane hazard is reduced Ventilation principles for gassy tunnels Monitoring for gas Eliminating ignition sources and The all-important human factors component] This chapter gives guidelines for preventing methane gas explosions during tunnel construction. Emphasis is placed on assessing the hazard potential, on ventilation principles, and on monitoring for gas. The chapter also emphasizes the importance of human factors in reducing explosion risk. Ensuring safe conditions is much more than just good engineering design. It also involves the every-day vigilance of those working underground. This does not imply that the engineering design can be ignored, only that the job of providing safe conditions has just begun with design. EARLY INDICATORS OF A GAS PROBLEM For the engineer planning a tunnel project, reliable early indicators of methane are scarce. How-ever, the local geology can often provide some information.2 Carbonaceous rocks and tar sands are a likely methane source. Gas is also a distinct possibility if it is known to be present else-where in the same sequence of geologic formations. Swampy areas, sewerage systems, and landfills are also candidates because the decomposition of organic materials produces methane. The gas in a tunnel can originate in the strata being excavated, or it can migrate a considerable distance from adjacent strata. Test borings at the project site can also serve as initial indicators of gas. Methane has no odor, but may be emitted along with gases that do. If gas is emitted from the borehole, a sample may be collected by inserting a tube into the hole as far as possible and pumping the gas out. The gas sample should be collected in a sampling bag or canister for later analysis by a chemical laboratory.3

Jan 6, 2006

By W. L. Crentz

In Fayette County, the Pittsburgh bed has been the major source of production for almost two centuries. Although historical documentation is not available, there is evidence, that the Pittsburgh bed may have been discovered in Fayette County near Mt. Braddock, Pa., as early as 1753. The earliest known reference to coal in western Pennsylvania was recorded in 1758 by a Quaker trader, James .Kenny, who reported having seen coal in Fayette County. The production of coke from Pittsburgh coal was begun in 1841, when two 10-foot beehive ovens were erected in the Connellsville region to make coke .for shipment by river to the market. The Connellsville, region extends from Latrobe, Pa., in Westmoreland County to South of Uniontown, in Fayette County. Connellsville coke was used with great success in the Clinton furnace in 1859.

Jan 1, 1951

By William S. Miska

The study is an economic evaluation of historical, current, and projected refractory uses in the iron and steel industry of the United States. The first part of the report presents a refractories classification and identifies principal trends in the refractories industry; such as, value and volume of shipments, prices of finished refractory products, the number of manufacturers and plants for refractories production and marketing. The main part of the report treats refractory use patterns and technologic developments affecting refractories usage in the iron and steel industry. Changes in use patterns in each furnace type, refractory, and installation costs and the future outlook for refractories in ironrnaking and steelmaking are covered. The last part of the report identifies the principal raw materials used in refractories production and treats trends in refractory raw material consumption. An appendix to the report contains historical time series graphs of shipments of refractory types used primarily by the iron and steel industry and principal refractory raw materials sold or used by producers. An equation of the line of best fit was calculated from the earliest to the latest year in each time series, usually 1950 to 1965; these were extrapolated in order to derive volume estimates for the year 1975.

Jan 1, 1968

By D. R. Wilburn

The Bureau of Mines investigated the potential availability of magnesium from 45 properties in market economy countries (MEC's). The 38 significant deposits evaluated have demonstrated resources of approximately 29 billion short tons (st) magnesium-bearing material containing 416 million short tons (MMst) magnesium oxide (MgO). Using data it gathered, the Bureau determined the magnesium production potential for each property including a 15-pct rate of return on invested capital. Total and annual availability assessments for the next 30 yr were completed for magnesium (Mg) metal, deadburned MgO, and caustic calcined MgO. At a January 1984 market price of $1.34/Ib Mg metal, the properties evaluated could economically produce an estimated 13 MMst Mg metal. At a market price of $400/st nonmetal magnesium product, these properties could economically produce 109 MMst deadburned MgO and 43 MMst caustic MgO. These properties could produce approximately 301,000 st Mg metal, 3.0 MMst deadburned MgO, and 430,000 st caustic MgO annually at current full production levels and 1984 market prices until at least the year 2000. Total 1984 MEC production assessed in this study was 153,000 st Mg metal and 4.3 MMst nonmetallic MgO products.

Jan 1, 1986

By R. T. C. Rasmussen

"INTRODUCTION This is the second report of investigations describing tests in full-scale commercial heats of steel-using electrolytic manganese having a purity of about 99.95 percent, produced in the Bureau's pilot plant at Boulder City, Nev. The first report dealt with tests in cooperation with two companies can the use,of electrolytic manganese in the manufacture of stainless steel. 3/ Plans aril cost estimates for reasonably large commercial, electrolytic plants based upon pilot-plant experience, as well as the comments of a number of concerns where electrolytic manganese has been tried, are contained in another publication.4/ The tests in cooperation with industry are part of the Bureau of Mines program of investigations of methods of utilizing low-grade domestic manganese ores, thereby the United States leas dependent upon foreign sources of manganese for metallurgical use. The Boulder City pilot plant already has demonstrated the feasibility of producing electrolytic manganese from several of the most important reserves of low-grade manganese ore. As the ferromanganese normally used by the steel industry represents the bulk of the Nation's manganese requirements, the usefulness and possi¬ble advantages of electrolytic manganese in the manufacture of steel must be established if electrowinning from domestic ores is to become an important factor of manganese supply.Preliminary arrangements for the cooperative tests at the Atlas Steel Casting Co., Buffalo,. N. Y., were made with E. L. Altenburg, vice president and general manager of the company, by A. A. Dow. 5/ The data on the tests at the Atlas plant presented herein are based upon reports of E. L. Altenburg and information obtained by the author during a visit to the plant to observe the initial trial heats with electrolytic manganese in the open-hearth and the electric furnace."

Nov 1, 1945

By H. D. Hess

This report presents the results of laboratory mineral evaluations conducted by the federal Bureau of Mines under the joint sponsorship of the U.S. Atomic Energy Commission (AEC) and the Bureau a! Ships, U. S. Department of the Navy. The major purpose of this investigation was to examine and evaluate zirconium minerals representing sizeable deposits in an effort to locate com¬mercial sources of high-hafnium ores. Although determination of the hafnium content was the principal objective, each of the zirconium minerals also was analyzed for combined zirconium-hafnium oxide, silica, uranium, thorium, yttrium, and cerium. The general laboratory procedure involved microscopic examination of the test samples, concentration of the hafnium-bearing zirconium mineral by standard laboratory techniques, and analysis of the derived concentrate by quantitative microscopic, chemical, and X-ray spectrographic methods. Of the several hundred samples tested under this program, 147 are discussed in this report, including 94 from domestic occurrences and 53 from widespread foreign sources.

Jan 1, 1962

Comparative tests of four coals used industrially for coke production have been made by three laboratories of the Federal Bureau of Mines, each using its standard equipment and procedures for evaluating coal for coking. Two of the coals were blends used in the western and eastern sections of the United States, the third was a strongly coking coal widely used for producing coke in Alabama, and the fourth was a blend typical of those used for producing foundry coke in the Birmingham district. The coals used and the cokes produced from them covered a wide range of chemical and physical properties. The tests used at all three laboratories for determining the physical properties of the cokes were made according to ASTM (American Society for Testing Materials) methods. The excellent agreement found for the physical properties of the cokes indicated that, for the coals tested, the BM-AGA (Bureau of Mines-American Gas Association) 18-inch circular retort used at Pittsburgh, Pa" the 14-inch slot-type oven used at Denver, Colo., and the 17-inch slot-type oven used at Tuscaloosa, Ala., were substantially equivalent for evaluating coals for production of coke. Thus, added value is given to data obtained previously and independently at these three Bureau laboratories. INTRODUCTION Laboratory equipment to produce coke for evaluation has not been standardized by the industry. The results obtained with anyone design of equipment have been regarded as showing only the relative values of coal to produce coke of the requisite quality. Few systematic studies have been made to correlate results obtained in different types of equipment. Results of one, in which the Bureau of Mines participated, were published recently.2/ This

Jan 1, 1961

By Louis A. Turnbull

An investigation of coal deposits near Cerrillos Santa Fe County, N. Mex., was undertaken 14 the Bureau of Mines in 1943 as part of a general program to determine sources of metallurgical coal for western steel plants. Almost all of the coal used for metallurgical purposes west of the Continental Divide Is mined from the Lower Sunnyside bed in, Carbon County,, Utah. Coke used in western steel plants that is produced from Lower Sunnyside a coal is weaker, structurally, than coke used elsewhere in this country. For this reason, western coal operators and steel manufacturers are anxious to develop new areas of coking coal of better quality then the coal produced from the Sunnyside bed. The objective of investigations of western coals was to (a) develop additional reserves of coking coal to supplement proved reserves in the Sunnyside bed. and (b) develop; if possible, reserves of coal with coking quantities superior to those of Lower Sunnyside

Jan 1, 1951

By Larry A. Haas

The U.S. Bureau of Mines, in cooperation with Cleveland-Cliffs, Inc. (Hibbing, MN), investigated ways of enhancing the quality (compressive strength, after-tumble and reducibility) of domestic acid and fluxed magnetite pellets by modifying the oxygen content during the preheat and induration periods of the firing operation . Oxidation of magnetite was best accomplished when sufficient oxygen and time were available before the peak induration temperature was reached. The rate of magnetite oxidation increased directly with the gas oxygen content during the preheat period at 7000 C and above. With 30 pct ( or more) O2 and a preheat rate of 2000 C/min, most of the magnetite was oxidized during the preheat period. With laboratory tube and mini-pot furnace tests, oxygen enrichment during the preheat period improved the pellet properties more in the simulated grate-kiln tests than in the simulated straight-grate tests. The longer induration period with the grate-kiln test resulted in more sintering of the residual magnetite and its reaction with the silicon compounds. When flux was present in the pellets, calcium silicates and calcium and magnesium ferrites were formed. More calcium ferrite was formed when the magnetite was oxidized early and less iron was present in the fayalitic calcium silicate slag.

Jan 1, 1993

By R. O. Pynnonen

Tunnel-driving is recognized as a hazardous occupation; adequate support of roof and sides for preventing accidents from falling material is usually one of the most important safety problems. Where extraordinary conditions of sand and water are found, this problem becomes even more difficult. Tunneling at the Tioga No.2 mine was stopped when a 22-foot bed of water-saturated, fine gray sand was encountered. The tunnel, designed to house an ore-conveyor belt, was being driven from both ends. Driving was extremely difficult at both the upper and lower faces when the sand horizon was reached. A distance of 178 feet remained between the faces. Heavy pressures deformed the steel-supporting rings at the upper face, and there was an inrush of mud and sand at the lower face.

Jan 1, 1958

By K. J. Miller

Electrophoretic mobility measurements of coal and pyrite particles in distilled water revealed a difference between the migration speeds of the two materials toward the anode in a dc electric field. This information led to the development of a laboratory electrophoresis column for separating fine pyrite from coal by utilizing the electrokinetic and the specific gravity differences between coal and pyrite. The study demonstrated on a laboratory scale that pyrite and other impurities can be separated from fine coal by electrophoresis using a stage separation technique. In a cost analysis, electrical power for electrophoresis was extrapolated to about $1 per ton of clean coal product. But, since the only successful tests ever made were in the laboratory with prewashed samples of minus 100-plus 325-mesh coal in distilled water, the cost figure derived is not representative of conditions prevalent in commercial coal cleaning operations. True conditions would reflect costs many times as great. In the course of the work, several scale-up techniques were considered but their feasibility became academic in view of the physical and economic problems associated with electrophoretic separation of pyrite from coal. Although the process and apparatus were finally deemed impractical for commercial coal preparation, the electrophoresis column may have some application as a laboratory device.

Jan 1, 1974

By Robert W. Waytulonis

The mining regulations of all 50 States were reviewed by the Bureau of Mines, and those parts pertaining to the use of internal combustion (IC) engines (particularly diesel engines) in underground mines or confined spaces were extracted. Also extracted were subjects associated with the use of IC engines; for example, storage and handling of flammable liquids, maintenance, and ventilation requirements. As the laws now stand, 29 States have specific regulations that affect the operation of diesel engines in underground coal and/or metal and nonmetal mines. The other States have no regulations because either they have no mining activities or they defer to Federal regulations. Six states have regulations expressly prohibiting the use of diesels in underground coal mines. Specific contacts (addresses and phone numbers) precede each State's regulations to facilitate inquiries about regulation revisions and interpretation.

Jan 1, 1981

By F. W. Smith

This paper is based largely on a study of experimental data obtained by the Bureau of Mines in its comprehensive 25-year survey of the carbonizing properties of American coals. Although the Bureau was interested in and conducted carbonization research-from time to time ever since it was organized in 1910 (1),4/ no systematic studies of the coke-, gas-, and byproduct-making properties of American coals were undertaken until 1927, when the American Gas Association appointed an advisory committee (2) to cooperate with the Bureau in developing equipment and techniques to obtain-data for the accurate assessment of the behavior of coals on carbonization. It was found, in general, that small-scale laboratory tests were unsuitable for the complete evaluation of the coking properties of coal; hence, larger pilot-plant-scale equipment was designed and used (3). It was decided that the scale of the test should be large enough to determine both the yield and quality of the products and yet small enough to maintain adequate control of the process variables (4). These considerations led to development of a carbonizing retort and furnace-of 80 to 200 pounds of coal capacity, suitable for operation at various temperatures up to 1,100° C. (2,0120 F.) and equipment for recovery and measurement of gas and byproducts. This apparatus and the standardized procedure for its operation became known as the Bureau of Mines-American Gas Association (EM-AGA) method or retort (5).

Jan 1, 1955

By J. D. Davis

The carbonizing properties of No. 2-bed coal from the Bartoy mine and No. 5- or Miller-bed coal from the Wilkeson-Miller mine, both at Wilkeson, Pierce County, Wash., were determined by the Bureau of Mines-American Gas Association (BM-AGA) method. Tests were made in the 13-inch retort at 500°, 600°, and 700° C. and in the 18¬inch retort at 800°, 900°, and 1,000° C. Fischer low-temperature and United States Steel Corporation high-temperature assays were made and the results compared with those of the BM-AGA tests at corresponding temperatures. Agglutinating and plastic properties were determined, and chemical and petrographic analyses were made. The No. 2 bed is 58.5 to 88.0 inches thick at three points sampled in the Bartoy mine. The coal is 98 percent bright and contains only a trace of fusain. A composite of three mine samples contained 13.8 percent ash. The washed sample, which was used in the tests described herein, contained 11.4 percent ash, 2.2 percent moisture, and 0.6 percent sulfur upon the as-carbonized basis and 68.4 percent fixed carbon upon the dry, mineral-matter-free basis. The heating value was 15,183 B. t.u. per pound upon the moist, mineral-matter-free basis. No. 2 therefore ranks as a high-volatile A coal and is very high in that, rank. The ash softens at 2,910° F. Except for its ash content, which is higher than the limit of 9.0 percent specified by the American Society for Testing Materials, No. 2 coal fulfills the requirements of a coking coal. It also is classed as extremely friable, the friability being 88.0 percent. The agglutinating index (7.6 for the 15 : 1 ratio of silicon carbide to coal) is high, and the plasticity as indicated by the Gieseler test (60 divisions per minute) is low for a high-volatile A coal.

Jan 1, 1942