Search Documents

By James E. Norman

[The flotation of mica is mentioned frequently in the literature, but most of the references have dealt with the recovery of mica by the old anionic collectors. The first use of the new cationic reagents indicated their superiority as collectors in the flotation and agglomerate tabling of micas, feldspars, guartz, clay, and other acidic minerals, but the separation of these minerals from each other necessitated of the study of the flotation of each mineral.]

Jan 1, 1941

By Edward W. Parsons

Conventional rock-bolt anchors often fail when installed in weak formations. The purpose of this work was to develop an anchor that would utilize an explosive charge to secure anchorage in any type of rock. Laboratory work to develop a rock-bolt anchored by explosive forming was initiated using rock-bolt models which had a drilled explosive chamber and were composed of various metals. This was followed by the use of several types of seamless tubing which were expanded with a water-coupled explosive capsule. By attaching a length of solid bolt to the anchor tube, a prototype explosive-anchored rock bolt was made. More than 150 laboratory models were expanded during this phase of development, During two field tests in underground mines (A and B) and one in an open- cut mine (C), 87 explosive-anchored bolts, 9 slot-and-wedge bolts, 2 bolts anchored with expanding grout, and 28 expansion-shell bolts consisting of three types of shells were installed and subjected to pull tests. The field tests were run to determine the effects of variables such as the amount and placement of the explosive charge, design changes in the bolt, and the effect on anchorage of different pull-test techniques. The field tests revealed the following: Mine A. The explosive-anchored rock bolt was feasible, but changes were necessary in bolt materials and in some details of bolt design. Mine B. The design and materials of the bolt gave excellent results in hard fractured rock, but no information was obtained concerning variations in the dimensions of the anchor unit or in the explosive charge. Nine C. Varying the explosive charge to produce a beaded surface on the bolt tube and tightening of the anchored bolt before pull-testing were found to increase significantly the anchorage obtained in soft ground.

Jan 1, 1963

By G. F. Friel

A series of experiments in the U.S. Bureau of Mines Safety Research Coal Mine at the Pittsburgh Research Center evaluated the effects of crosscuts on the travel time of carbon monoxide (CO) along an entry to improve the accuracy of a mine-fire locator program. Three entries, ten single crosscuts, and three double crosscuts were instrumented with CO sensors. One-percent CO in nitrogen was released and monitored as it traveled the entries. In addition to dispersion of CO at the front of the CO wave, CO was entrained from the entry into the crosscuts. It was determined for an entry and single-crosscut configuration that the measured travel time for a concentration change of 5 ppm was 27% greater than the predicted time based upon entry volume only, but 13% less than the predicted time based upon entry and crosscut volumes. For an entry and double-crosscut configuration, the measured travel time for the same concentration change was 25% greater than the predicted time based upon entry volume only, but 10% less than the predicted time based upon entry and crosscut volumes. An effective dispersion coefficient for CO dispersion along one of the entries was estimated to be 1.5 m2/ s.

Jan 1, 2010

By P. L. Sibrell

Electrorefining of Ti in nonaqueous solvents has been studied by the U.S. Bureau of mines as a method for recycling impure scrap Ti. Electrochemical behavior of Ti species was investigated using cyclic voltammetry. Research results showed that Ti metal can be dissolved in polar solvents such as dimethylformamide or dimethyl sulfoxide. However, deposition of Ti from these solvents was not successful. Several solvent systems were investigated for electrodeposition of Ti but no deposits were obtained. Reduction of Ti4+ complexes to Ti3+ proved to be straightforward, but reduction to lower oxidation states could not be confirmed. In dimethylformamide solutions, cyclic voltammetry results demonstrated the reduction of Ti to an oxidation state of less than three, but no Ti metal was identified. In dimethyl sulfoxide solutions containing LiCl, it was possible to deposit Li metal. After adding Ti salts to the solution, electrolysis quickly passivated the electrode. Deposition of Ti was also investigated in solutions of dimethoxyethane and propylene carbonate but, again, no reduction of Ti to oxidation states of less than three occurred. Therefore, the prospects for a nonaqueous electrorefining system for Ti metal do not appear promising.

Jan 1, 2010

By Harry Dobroski

Communications with moving tracked vehicles in a rail haulage mine pose a difficult problem. These communications take place from dispatcher to vehicles or from vehicle to vehicle via the trolley line, which is a very poor communications line. As a result, deadspots and high-signal areas can occur anywhere along the line, or signal can decrease simply as a function of distance. An analysis is made of the trolley line as a communications line, and methods of improving its characteristics are discussed. Data from inmine experiments are presented, showing actual improvements in communications. Recent Bureau developments in new hardware are also discussed. These include an adaptive speaker control for existing carrier phones and a new generation of improved carrier phones.

By V. A. Marple, K. L. Rubow, S. M. Behm

"An eight-stage cascade impactor, with cut-sizes ranging from 0.056 to 18 um at a flow rate of 30 L/min, has been developed, calibrated, and tested in field programs. This impactor, called a microorifice uniform deposit impactor, has several features not normally found in cascade impactors. Ultrafine particles as small as 0.056 um are collected while keeping the pressure drop moderate by utilizing multiple nozzles (up to 2000) as small as 52 um in diameter. At each stage the collected particles are deposited uniformly over the entire impaction plate by rotating the impaction plate relative to the nozzles and by the correct radial placement of the nozzles. The particle cutoff characteristics (collection efficiency curves) of each stage and inter-stage losses were determined by means of monodisperse aerosols. The cutoff characteristics were found to be sharp and similar for all stages.Inertial impactors are widely used for the size-selective collection of aerosol particles. One reason for their wide usage is that the principle of operation is simple: a jet of particle-laden air is directed at a flat impaction plate. Large particles are collected on the plate while smaller particles follow the airflow out of the impaction region and are not collected. The division between the size of particles collected and those that are not is quite sharp. Secondly, the particles in an impactor are classified by their aerodynamic diameter (an important size parameter in many fields of study, including those related to respirable particle health effects). Thirdly, it is easy to collect particles in discrete size ranges by passing the aerosol through a number of stages (one stage consisting of a nozzle and impaction plae) in series, with each subsequent stage collecting particles smaller than the one before it. This is known as a cascade impactor. Finally, impactors can classify particles over a wide range of particle sizes: as low as 0.005 um (Fernandez de la Mora et al., 1990) and as large as approximately 50 um (Vanderpool et al., 1987).This paper describes a general purpose cascade impactor that has been developed in our laboratory and used in a variety of studies including visibility studies (McMurry et al., 1986; McMurry and Zhang, 1989), underground mine studies (Marple et al., 1986; Rubow and Marple, 1988; Rubow et al., 1988), and general atmospheric pollution studies (Macias et al., 1981; Dzubay et al., 1984). The impactor, called a microorifice uniform deposit impactor (MOUDI model 100, MSP Corp., Minneapolis, Minn.), is the integration of two earlier impactor de¬velopments: the microorifice impactor (M01) (Kuhlmey et al., 1981) and the uniform deposit impactor (UDI) (Marple et al., 1981).The MOUDI has several features normally not found in other cascade impactors. These include collection of particles as small as 0.056 um in aerodynamic diameter with a moderate pressure drop, uniform particle collection on the impaction plates, inter-changeable impaction plates to allow for the plates to be easily and quickly changed in the field, and covers for these substrates to provide a means for safe storage and/or transport of the collected particles to the laboratory for analysis."

Mar 1, 1992

By John H. Soule

The Torpedo Copper mine in the Organ Mining District, Dona Ana County, N. Mex., was discovered In 1899. Production was begun immediately and continued until 1907. Since 1907 very little ore has been produced, although Many individuals and companies have been interested in the property at one time or another. Approximately 6,621 feet of diamond-core had been completed on the property before 1949. The results from some of this drilling were unsatisfactory because of the poor core recovery. In addition to its investigation of the Torpedo ore deposits, attention was given by the Bureau of Mines to obtaining better core recovery through the use of special equipment and techniques. This project was begun October 3, 1949, and was completed April 30, 1950. Four diamond-drill holes totaling 2,140.5 feet, which includes 18.2 feet of overlap in a deflected hole, were drilled. All drilling was done with a Government-owned hydraulic-feed drill with some special rods and core barrels, in addition to the usual equipment. The over-all core recovery was 89.5 percent. Omitting the drilling in overburden where little or no core was desired, the recovery was 94.6 percent. Core recovery in the ore zones averaged 95.2 percent. This paper describes the location, the general features of the area, the geology, the Bureau of Mines procedures, and the results attained by these procedures.

Jan 1, 1952

By Wm. F. Netzeband

The purpose of this paper is to present to the operators, in other districts a detailed description of the ruining method used and the results obtained to exploiting one of the zinc-lead deposits of the Kansas-Oklahoma-Missouri district. No. 1. mine is located in the heart of the town of Picher in the extreme northeast corner of Oklahoma. HISTORY The first prospect drilling was done at No. 1 mine late in-1914, and shaft sinking was started early in 1915. Sufficient ore was developed to start construction of the mill in April, 1016, Production begin in August, 1916, and the mine s been producing, except for short periods, to the present time. The property was originally a 40-acre tract, but additional properties have been consolidated with the original one until the mine now covers 200 acres.

Jan 1, 1929

By Thomas M. Barczak

The U.s. Bureau of Mines is conducting research to optimize the utilization and design of mine roof support systems. This report describes methods to evaluate resultant loading on longwall shields, defined as external resultant vertical and horizontal force acting on the canopy and base. Four models are considered: two rigid-body models, an elastic model, and a numerical model. The rigid-body models equate measured internal shield forces to unknown external resultant shield forces (loads) through rigid-body analysis of static equilibrium requirements. The elastic model develops a solution to shield mechanics by evaluation of the load-displacement relationship and stiffness characteristics of the support structure. The numerical model is a two-dimensional finite-element representation of a shield structure. Model determination of resultant shield loading is compared to controlled loading of a shield in the Bureau's mine roof simulator. Parameters investigated are shield height, canopy contact configuration, canopy and base horizontal constrainment, and boundary conditions imposed by vertical and horizontal shield displacements. It is concluded that rigid-body models are most applicable to in situ measurement of shield loading. Applications requirements and potential error sources are discussed.

Jan 1, 1990

By G. M. Molinda

The U.S. Bureau of Mines conducted an investigation to determine the nature and frequency of coal mine roof failure beneath valleys. A mechanism for this failure and suggestions for controlling this problem are presented. Hazardous roof conditions identified in some mines were positively correlated with mining activities beneath stream valleys. Mine maps with overlays of unstable roof and locations of stream valleys show that 52 pct of the instances of all unstable roof in the surveyed mines occurred directly beneath the bottom-most part of the valley. The survey also showed that broad, flat-bottomed valleys were more likely to be sites of hazardous roof than narrow-bottomed valleys. Evidence of valley stress relief was found beneath several valleys in the form of bedding plane faults and low-angle thrust faults. This type of failure, previously believed to be only a shallow phenomena, was found at mining depths as great as 300 ft. In situ, horizontal stress measurements beneath a valley and the adjacent hillsides, confirmed valley stress relief. Numerical analysis of 13 valleys overlying one mine property showed the effect of the valley excavation on horizontal and vertical stress.

Jan 1, 2010

By Thomas J. Peters

In 1987, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 15,174-acre Sleeping Giant study area, including the 6,112-acre Wilderness Study Area (MT-075-111), in order to evaluate its identified mineral resources. The study area is located in Lewis and Clark County, MT, about 30 miles north of Helena. Sleeping Giant Mountain trends west-northwest from the Missouri to the eastern crest of Little Prickly Pear Canyon (the route of Interstate 15), and has several summits over 6,000 ft. Geologically, the area is in the Disturbed Belt, and a large block of Middle Precambrian metasedimentary siltstone and underlying shale has been thrust northeast over younger, sedimentdry volcanic and intrusive rocks.

Jan 1, 1988

By Gabriel S. Esterhuizen, Jarek Jakubec

In 2000, Laubscher’s Mining Rock Mass Rating (MRMR) classification system was updated and published. The new system brought a few fundamental changes that were in direct response to the challenges and problems encountered when applying the classification system in the mining environment, specifically caving operations. The fundamental changes introduced into the MRMR system in 2000 were the abandonment of the Rock Quality Designation (RQD) as an input parameter, accounting for healed and cemented joints, and the concept of rock block strength. The objective of this paper is not to discuss the role and usefulness of classification systems; the fact that classification systems are widely used in every stage of mining projects speaks for itself. This paper discusses some of the experiences gained with the MRMR 2000 system in various mining projects and shows how the changes to the system have resulted in improved assessment of rock mass conditions. Issues related to core logging for rock mass assessment are also presented.

Jan 5, 2007

By Sean Gallagher, John R. Bartels, Dean H. Ambrose

Remote operation of continuous miners has enhanced the health and safety of underground miners in many respects; however, numerous fatal and non-fatal continuous miner struck-by accidents have occurred when using remote controls. In an effort to prevent these injuries, NIOSH researchers at Pittsburgh Research Laboratory examined the workplace relationships between continuous miner operators and various tramming modes of the equipment using motion captured data, predicted operator response times, and field- of- view data to determine causes of operator-machine struck-by events in a virtual mine environment. Factors studied included machine speed, direction of escape, operator facing orientation relative to the machine, work posture, distance from machine, and operator anthropometry. Close proximity to the machine, high machine tramming speeds, a right-facing orientation and operator positioning near the tail all resulted in high risk of being struck. It is hoped that this data will provide an improved rationale for operator positioning for remotely operated continuous miners.

By A. F. Cohen

When location guidelines are followed in choosing sites for fixed point velocity transducers for use in underground coal mine monitoring, mine air turbulence intensities <11% are generally expected at those sites. The objective of this Bureau of Mines investigation to determine the effect of turbulence intensities <11% on vortex shedding sensors and transducers. Measurements were made at velocity levels of interest for underground coal mine monitoring use (?200, ?500, ?1,000, ?1,500 ft/min). The effect of grid-produced turbulence intensities (2% to ?14%) on the output of vortex-shedding air-velocity transducers was less than ±10%.

Jan 1, 1985

By Allen McComas, Frank Chase, Phyllip Worley

Longwall mining has gained the reputation as being the safest extraction method in underground coal mines. However, one of the most difficult tasks associated with longwall mining is moving the face once a panel is completed. Based on Mine Safety and Health Administration (MSHA) fatality reports since 1996, longwall face recovery operations have claimed the lives of 5 U.S. miners and have resulted in numerous injuries. Recovery operations can be hazardous because they involve moving large pieces of equipment in very confined spaces. They are also conducted in highly stressed ground conditions due to front abutment loads generated by panel extraction. Shield removal is the most hazardous operation during face recovery because miners are constantly exposed to the unpredictable gob edge. To protect the miners, one or more walking shields, cribbing and/or other supplemental roof and standing supports are typically employed as breaker line supports as each shield is removed. At the Harris No. 1 Mine in southern WV, mobile roof supports (MRS’s) have been used in lieu of traditional walking shields on 17 face moves since 1997. MRS’s are shield-like support units mounted on crawler tracks and are commonly used during room-and-pillar retreat mining operations. For longwall recovery, the two biggest advantages that MRS’s have over traditional walking shields are that they are remotely controlled and are highly maneuverable. MRS’s have contributed to safer shield recovery and shorter move times at the Harris No. 1 Mine. This paper will address both the safety and the operational issues associated with MRS usage during shield recovery. It will also discuss new developments, including the use of the inherently safer battery powered MRS’s, which have been recently certified by the Mine Safety and Health Administration.

By W. P. Yant

Canister-type gas masks have become an essential part of the equipment of many industries not only for use in emergencies, but also in performing normal operations of industrial processes and procedures, particularly where ventilation is not practically or economically feasible. They are also used widely for enhancing safety of operations which previous to the development of gas masks had been performed in harmful atmospheres. Since the inception of industrial gas masks the Bureau of Mines has been actively engaged in endeavoring to increase the efficiency and safety of these devices and this bureau has become a source of advice to manufacturers in producing devices of good quality and to industry in the proper selection and use of these devices. In order to give first-hand information and keep current with the demands and needs of industry it is necessary to perform investigations from time to time. This report deals with tests of certain types of commercial gas-mask canisters for protection against mercury vapor.

Jan 1, 1932

By Richard D. Miller

This Bureau of Mines publication contains analyses and related source data for 271 natural gas samples from 22 States collected during calendar year 1982. All samples were obtained and analyzed as part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by the mass spectrometer and chromatograph. The results of the investigation of the occurrences of helium are published annually to make the information available to the petroleum industry and the general public. Twenty-six publications have presented the results of 13,051 gas analyses vide prior to 1982. The first 3 bulletins (1-3)3 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960; these bulletins have been supplemented annually by information circulars (4-17, 19-24, 26) containing 7,833 analyses of samples collected since 1960.

Jan 1, 1983

By S. P. Howell

"Technical statistical study has been made of accidents in the anthracite region of Pennsylvania in which explosives were involved. The data have been taken from the accident reports in the files of the department of mines of Pennsylvania, supplemented by inquiries in the field.This study has disclosed a wealth of information regarding the nature and the cause of accidents that occurred where different means of firing shots of explosives were employed. In the anthracite region shots are fired with fuse, with squibs, and with electricity,Many of the salient features of this accident experience are illustrated in this report of investigations, and a number of recommendations are made to reduce the hazards of each of these three methods of shot firing.Experience seems to demonstrate that, under conditions in the anthracite region, electric firing of shots is substantially the safest method; that accidents wherein fuse is employed are more frequent than accidents in which electric firing is employed; and that the number of accidents when squibs are employed far exceeds those in which either fuse or electric firing is used."

Mar 1, 1930

By M. J. Ackerman

This study was undertaken to make a comparison between the cost of mining coal under roof bolt and under conventional timber methods of roof support. Studies were made at 14 mines in Pennsylvania, eastern Ohio, and northern and southern West Virginia. At each mine data were obtained for sections of the mine where the physical conditions, mining equipment, and mining systems were similar. Coal, recognized as one of the basic industrial fuels, is very competitive with other fuels, and management, in order to protect and enlarge its market, must be continually alert to find more efficient methods of production. Continuous production of coal is desired by all operators but never obtained. In mechanized mining the performance and production vary with operating time, which can be interrupted by many variable factors, such as condition of the roof, method of roof support, condition of equipment, water, ventilation, power, transportation, efficiency of operating crew, and supervision.

Jan 1, 1961

By J. F. Barkley

Field tests were made on the rate of corrosion of 30 materials used in air preheaters under regular operating conditions, and the buildup of deposits was observed. Twenty-three materials were tested with coal as the fuel on an underfeed stoker and seven with oil, including a short period with pulverized coal as fuel, The plant equipment is described, and pertinent plant operating data are tabulated. Figures 17 and 19 (pp. 24 and 27) give the results of corrosion tests on the uncoated metal test specimens. The information obtained from these tests follows the general pattern described in Bureau of Mines Report of Investigations 4996, Corrosion and Deposits in Regenerative Air Preheaters. The deposits were similar, and the corrosion rates of Cor-Ten and Mayari-R steel (previously found to be essentially the same at the Harding Street Station using coal) continued to show little difference at the Marion Generating Station using principally oil. The one high-alloy steel tested, type 321, showed a much higher corrosion rate than the low-alloy steel, Cor-Ten.

Jan 1, 1959