Search Documents

By R. H. Thompson

Preliminary safe distances for blasting wiring from typical electromagnetic sources are presented. The distances are for underground coal mines and electromagnetic sources in the frequency range below 10 MHz. The distances are based on measurements performed at 3 locations in each of 3 coal mines. The measurement apparatus, measurement procedure, measurement results and the rationale used in the calculation of the safe distances are all described. The safe distances presented are dependent on the measurement results and their interpretation. More measurements are clearly necessary to establish the validity of the suggested distances.

Jan 1, 1985

By Charles D. Litton

An overview of state-of-the-art technology in fire detectors is presented by the Bureau of Mines regarding their use in the mining industry. Detectors are categorized according to the characteristics of a fire to which they respond. Operating principles of the various detectors, their application, and the advantages and disadvantages of each are discussed.

Jan 1, 1979

By Floyd C. Bossard

Major air-cooling facilities have been installed and are operating underground in U.S. copper mines (at Butte, Montana and Superior, Arizona), South African gold mines, European coal mines, Zambian copper mines, Kolar gold mints in India, Coeur d'Alene mines of Idaho, plus other locations. Mining districts that utilize spot cooling and local air-cooling facilities would increase the above listing many times. The principal objectives of underground mine air cooling systems are to; 1. Extract heat and water vapor from the mine air and provide for their removal from the mine via (a) water pumped to surface or (b) discharged mine exhaust air. 2. Provide acceptable artificial ambient conditions for efficient working mine development and production areas. 3. Recondition used air, thus supplementing the limited mine ventilation balance. In deep South African gold mines, when rock temperatures exceed about 105°F, cooling of underground air becomes necessary for the poorly ventilated sections of the mine. By U.S. standards, air conditioning in poorly ventilated mines usually commences when the virgin rock temperature exceeds 100°F. On the other hand, well ventilated deep vein-type mines in the U.S. have been able to forego general cooling of mine air until the mines have been extended to such depths that the virgin wallrock temperatures have exceeded 115° - 120°F. It must be noted that spot-cooling of selected development headings may be required in many mines where rock temperatures exceed 100°F. Such local air-cooling practices permit the driving of long headings for exploration or extended development prior to holings which result in establishment of primary ventilation circuitry. The following summary reports on current practices of cooling and dehumidifying mine air. General system descriptions with important details will hopefully permit the reader to gain an understanding of the subject. A list of references is provided for this serious investigator who desires a more thorough knowledge-base and who is responsible for the design of a mine air-cooling system.

Jan 1, 1973

By Steven J. Page, Andrew B. Cecala, John A. Organiscak

In This Chapter [Drill dust control: wet and dry Enclosed cabs on drills and mobile equipment Haul road dust control] Overburden drilling generates most of the respirable dust that affects workers at surface mines. Both wet and dry methods are available to reduce this drill dust. Overburden removal by mobile excavation equipment such as bulldozers, front-end loaders, and haulage trucks can be dusty, particularly under dry and windy conditions. Tightly enclosed cabs with dust filtration systems can substantially lower the dust exposure of both drill and mobile equipment operators. Haul road dust control can be achieved by water application or chemical application. DRILL DUST CONTROL [Drill dust is controlled with wet or dry systems. Wet systems can be more efficient, but may freeze in the winter. Dry systems require careful maintenance of the drill deck shroud. An improved deck shroud is shown.] Wet Suppression. Wet drilling systems pump water into the bailing air from a water tank mounted on the drill. The water droplets in the bailing air trap dust particles as they travel up the annular space of the drilled hole, thus controlling dust as the air bails the cuttings from the hole [Page 1991]. In wet drilling systems, typical water flow rates are 0.1 to 2.0 gpm depending on the size and type of drill and the moisture level of the overburden. The drill operator controls the flow using a control valve located in the cab. Some drills are equipped with a flow meter to give the opera-tor a visual sign of the flow rate. Raising the water flow will improve dust capture, but too much water causes operational problems. Because of this, the drill operator must exercise care in find-ing the best water flow rate.

Jan 6, 2003

By Douglas W. Fuerstenau

A detailed experimental study of breakage kinetics in a batch rod mill indicates that while the system is inherently nonlinear, the feed disappearance kinetics for the finer sizes and the coarser sizes at high holdups is well represented by first-order behavior. The set of breakage distribution functions was found to be normalizable and independent of particle holdup in the mill. The size discretized initial breakage rate functions were found to be inversely proportional to particle holdup and almost directly proportional to particle size. A linearized grinding model that results from the first-order Taylor's series expansion of the breakage rate expression was found to give good simulations of the mill product size distributions without recourse to any parameter improvement routines. Material transport through rod mills was evaluated by investigating the effect of operating variables on the holdup and residence time distribution of particulate solids flowing through the mill. Identical experiments performed in a continuous ball mill helped delineate the fundamental differences in particulate transport through these two types of mills. Mechanistic interpretations of the observed transport phenomena are presented, and their implications in the context of tumbling mill analysis and design pointed out.

Jan 1, 1980

By J. P. Morris

An experimental blast furnace in normal operation was quenched by substituting cold nitrogen for the hot blast air. More than 2,200 samples from the stack, bosh, and hearth were taken; 500 of these were selected for detailed analysis. Deductions are made as to the patterns of burden movement and gas flow; the reduction of iron oxides, including a comparison of ore and sinter; and the behavior of sulfur above the smelting zone. Metal and slag beads from the bosh were analyzed, as were samples from the hearth metal and slag. A brief description of a petrographic examination of the quenched burden is included.

Jan 1, 1963

By W. W. Adams

The year 1937 was signalized by increased employment in the metal-and nonmetal-mining 4 industry of the United States. Measured by the number of men working, there was a 17-percent gain in employment compared with 1936. In total number of man-hours worked at all mines, the gain was slightly over 18 percent. Hazards connected with mining resulted in more accidents to the workers than in 1936, but the increase in number of accidents caused only a slight rise in the accident rate because of the much larger increase in the number of man-hours worked. In fact, the fatality rate per million man-hours of exposure was lower in 1937 than in 1936, but the rate for nonfatal injuries increased slightly.

Jan 1, 1940

By Martin Hertzberg

This Bureau of Mines report analyzes diverse observations of the rates and mechanisms for the pyrolysis and devolatilization of coal and polymethylmethacrylate (PMMA). New data are presented for PMMA, together with new morphological evidence for the microscopic structure of the pyrolysis and devolatilization wave front in coals. It is concluded that there is no substantive evidence to support the traditional viewpoint that the pyrolysis and devolatilization rate process occurs isothermally, under chemical rate control; or is described realistically by a classical, unimolecular Arrhenius function of temperature. Instead, the reaction process occurs as a highly nonisothermal, heat-flux-driven, pyrolysis and devolatilization wave front, whose speed of propagation is predictable by internal heat transport constraints. Except for the complication of its charlayer residue, whose increasing thickness insulates the pyrolysis wave front from the heat source flux that drives it, both coal and PMMA behave similarly during pyrolysis and devolatilization. For PMMA, decomposition occurs at a temperature of 3500 to 5500 C; for coal it occurs at 4500 to 6000 C. There is no evidence that the reactant temperature ever exceeds those values regardless of the source temperature to which the samples are exposed.

Jan 1, 1988

By Donald J. Frendzel

The post-World War II expansion of the Soviet petroleum industry has established the U.S.S.R. as a major oil-producing nation and has led to Russian reentry into the international petroleum trade. The rapid growth of Soviet petroleum production will allow the U.S.S.R. to displace Venezuela as the world's second largest oil-producer in 1960 and to narrow further the gap between Soviet and U.S. crude-oil production. U.S.S.R. crude oil output was only a tenth of U.S. production in 1946, but it will be more than a third at the end of 1960 and more than half in 1965. The Soviet Seven-Year Plan (1959-65) for oil provides for substantial increases in petroleum production, refining, storage, and distribution facilities. Crude oil production and primary distillation capacity are to double, considerable storage capacity is planned, and pipelines for crude oil and petroleum products are to increase threefold. According to the Soviets, the initial phases of this plan (1959 and 1960) have been completed successfully. However, this progress has been achieved with difficulty.

Jan 1, 1961

By Larry R. Powell

As part of the Bureau of Mines effort to establish a comprehensive subsidence data base for subsidence technology development, subsidence and related data are being compiled for various mining, geological, and environmental situations. This publication presents data for two longwall mining operations in the Northern Appalachian Coal Region. Vertical displacements and relative face positions are tabulated for 104 subsidence monuments. Brief physiographic and geological descriptions of the mining sites are presented along with a general account of the mining and subsidence monitoring methods.

Jan 1, 1981

By Charles W. Huggins

A study of the high magnification of some inorganic fibers which are found in nature or produced in the laboratory, has been conducted with the electron microscope. This series of electron microqraphs shows the important morphological differences exhibited by potassium-lead silicate, lead-aluminum silicate, chrysotile, wollastonite, silicon nitride, potassium titanate, cobalt chrysotile, magnesio-fluor-richterite, fluor-richterite, refractory oxide fiber, silicon carbide, massive serpentine, and palygorskite. A ribbon or a thin lath 250-2500 A. wide is the structural form of potassium-lead silicate and lead-aluminum silicate. Chrysotile, cobalt chrysotile, and massive serpentine all have a tubular structure and a fairly uniform (150-300 A.) diameter. Wollastonite, potassium titanate, fluor-richterite, and magnesio-richterite crystals have a lath shape, and potassium titanate laths are laminated ribbons. Single fibers of silicon nitride and palygorskite are ribbons, and the silicon nitride sample contains many twins (branching fibers). Palyqorskite fibers are highly flexible and have cross-sectional measurements of 150-300 A. Silicon carbide fibers differ from other fibers because their structure consists of several different forms. The sample used in this study had, predominately, a margarite-type structure. The refractory oxide fiber lost, all its apparent fibrosity after being prepared for electron microscopic examination, and only irregular fragments are visible in the electron micrographs.

Jan 1, 1962

By D. R. Corson

The Bureau of Mines instrumented an operating stope in a deep vein mine to determine the amount of wall closure and the magnitude of loads imposed on a backfilled stope. Hydraulic pressure cells used to monitor pressures in the fill) with bolt closure points to measure vein-wall movement and the procedure for their installation) are described) and the results of the laboratory calibration analysis of the reliability of these cells are given. An attempt to monitor density and moisture changes in the backfill with a nuclear density-moisture device was only partly successful) owing to either deformation of access tubing or relative displacements of the vertical vein walls relative to the emplaced tubes. Data from the instrumentation indicate vein-wall closure in excess of 20 inches and pressures within the fill approaching 600 psi. Analysis) incorporating field data with results of laboratory tests of the compressibility of timber and tests defining the constrained moduli of the fill) points out the limited restraint to vein closure offered by timber sets. Ground movement induced by mining activity could be more effectively con-trolled by the use of densely compacted backfill.

Jan 1, 1967

By J. S. Dunning

Recent developments in energy conversion, mining and minerals processing, pollution control, and chemical equipment have placed in-creased demands on heat-resistant alloys. Higher corrosion rates from oxidation, hot corrosion, and sulfidation have increased consumption of materials that contain critical and strategic minerals and in many cases have limited productivity. The Bureau of Mines is conducting re-search on substitute materials having greater resistance to high-temperature corrosive atmospheres above 6000 C compared to austenitic stainless steels such as AISI 304, 316, and 310, with the goal of conserving critical metals such as Cr and Ni. The substitute materials are based on Fe-Cr-Ni-Al compositions. Aluminum additions to Fe-Cr-Ni alloys significantly improve high-temperature corrosion resistance, particularly sulfidation resistance. In the alloy, devised by Bureau researchers, aluminum additions are held in the form of a second-phase precipitate, 8NiAl. Minor additions of Ti, Mn, and Si improve workability.

Jan 1, 1984

By Virgil A. Marple

The primary purpose of this contract was to evaluate methods and techniques by which the size distribution acid concentration of mining-related dusts can be measured. One result has been the development of a portable, battery-operated optical particle counter/ multi-channel analyzer system which can he used to determine the size distribution and concentration of mining aerosols. One important aspect of this program has been the development of a calibration technique which relates the output of the optical particle counter to the penetration of the particles through an impactor: This results in a calibration curve in terms of the aerodynamic or Stokes' diameter or the aerosol particles. Using this technique, calibrations were performed on coal, silica, Arizona road dust, potash, and rock dust (corer ore) aerosols. Another task of this program was the calibration and evaluation of the GCA respirible dust monitors (RMD) 101-1 and 301. The results of evaluation showed that the instruments were within the manufacturer's specification of ±25% of the true mass concentration up to about 15 mg/m , if the dust particles were in a size range from about 0.7 to 10 µm aerodynamic diameter. Particles smaller tan about 0.7 µm were not collected by the instrument and particles larger than about 10 µm were lose in the inlet. Other tasks included performing field studies in cooperative research programs with the Bureau of Mines personnel, development of a portable polystyrene latex generator for use in optical particle counter calibrations in the field. The incorporation of impactor classification devices on the inlets of aerosol mass measuring instruments to give mass size distributions, and a study of the density of coal particles as a function of the particle size.

Jan 1, 1977

By E. C. Lane

This paper is the first putt of a report giving the results of the Bureau of Mines' twenty-third semiannual survey of motor gasoline marketed in the United States. A companion report, Part II, is in preparation and will give a more detailed discussion of the whole survey. Results of the determination of copper-strip corrosion, color, sulphur content, copper-dish evaporation residue, and gum content as given by the Bureau of Mines steam-oven method will be presented in the second paper, which will also include the prevailing retail price and the tax at the time the sample was taken. This paper deals specifically with data relative to gravity, Reid vapor pressure,' and distillation (method 100.13).6 The samples tested were divided into "competitive-price gasolines" and "premium-price motor fuels," a method of presentation that was begun with the twenty-second semiannual survey. A total of 312 samples were collected from service station pumps in 20 cities throughout the United States. Of this number of samples, 207 were "com-petitive-price gasolines" and 106 were "premium-price motor fuels." All of the samples were collected in March, 1931, and analyzed at the Petroleum Experiment Station of the United States Bureau of Mines at Bartlesville, Okla. "Competitive-price gasoline" includes those fuels that are sold at the generally recognized local base price and all fuels that are sold below that price. All fuels that are sold at an advance over the generally recognized base price are placed in the class of "premium-price motor fuels." These fuels include Ethyl gasolines, benzol blends, "high-test" fuels, and those fuels that owe their "anti-knock" rating to the process of manufacture rather than to the addition of other material such as Ethyl fluid or benzol. The term "high-test" is generally applied to motor fuels that are more volatile than the regular competitive-price gasolines. "High-test" fuels may also have a high anti-knock rating.

Jan 1, 1931

By D. Harrington

The placing of much, sometimes practically all, of the burden of the expense of mine accidents on the shoulders of the mine operator by compensation laws, and the fact that the problem of protecting the life end limb of workers is now by public opinion largely if not wholly passed to each industry to solve (and present-day thought strongly supports the justice of both of these propositions), are forcing industrial organizations into accident-prevention. Work. This policy is being adopted not alone to protect the companies; in addition, executives alert to their opportunities and obligations are taking part in this work personally to protect themselves. The functions of industrial executives in accident-prevention work are becoming numerous and complex. Executives who are logical in their reasoning, quickly see that before a company can constantly ask or expect the workers to heed safety suggestions, the company and its officials must "put their house in order" by laying down a concrete, definite safety program. For mines this includes primarily adoption of a to a logical mining method, the installation of safe miming equipment and practice the netting forth in definite form (preferably do a printed pamphlet) of the company's minimum safety requirements, and the organization of its operating officials into an accident-prevention body. After the company has its own affairs so arranged that it can go to its workers with "clear, hands" in promoting a safety program, the real work begins; and this is especially applicable in mining.

Jan 1, 1939

By Ronald T. Mayerle

A mineral survey of portions of two contiguous WSAs (Wilderness Study Areas) along the South Fork Owyhee River in southwestern Idaho and north-central Nevada was done by the U.S. Bureau of dines in 1984. The portions of the WSAs, known as study areas, have a combined area of 47,610 acres. The Idaho study area consists of 42,430 acres of the 42,510-acre South Fork Owyhee River WSA (ID-16-53). The Nevada study area consists of 5,180 acres of the 7,840-acre South Fork Owyhee River WSA (NV-010-103A). The Idaho study area is within the Boise District of the Bureau of Land Management, and the Nevada study area is within the Elko District. In the Nevada study area, no claims or hard rock mineral occurrences are known.

Jan 1, 1986

In the three years to June 2005, 959 injuries associated with continuous miners (CMs), shuttle cars (SCs), load-haul-dump and personnel transport (PT) were reported by NSW underground coal mines, comprising 23% of all injuries reported. The present paper reports an analysis of the narrative field accompanying these reports to determine opportunities for controlling injury risks. The most common combinations of activity and mechanism were: strain while handling CM cable (96 injuries); caught between or struck by moving parts while bolting on a CM (86 injuries); strains while bolting on CM (54 injuries); and slipping off a CM during access, egress or other activity (60 injuries). For the other equipment considered, the common injury mechanism was the vehicle running over a pothole or other roadway abnormality causing the driver or passengers to be injured (169 injuries). Potential control measures include: monorails for CM services; hydraulic cable reefers; handrails on CM platforms; redesign of CM platforms and bolting rigs to reduce reach distances during drilling and bolting; improvements to guarding of bolting controls; standardisation and shape coding of bolting controls; two handed fast feed; improvements in underground roadway maintenance, vehicle suspension, visibility and seating; and pedestrian proximity warning devices.

By John P. Gooch

The solubility of 1,1,2,2-tetrabromoethane (TBE) in water was determined from 1.0° to 97.0° C. The solubility (S) of TBE in grams of solute per 100 grams water was correlated with [S = 1,920.55 [exp (40292L7 11, T2 10 T 737.577 + 9.923962 ] where T is in degrees Kelvin. A thermodynamic analysis conducted on a system consisting of a TBE phase and a water phase in equilibrium with a vapor phase led to the calculation of the activity coefficient, vapor-liquid equilibrium distribution coefficient, relative volatility, and heat of mixing for saturated solutions of TBE in water. Data required for these calculations were the solubility of TBE in water and the vapor pressures of TBE and water as a function of temperature.

Jan 1, 1972

By Joseph Grumer

Theory pertaining to the exchangeability of fuel gases on appliances has been extended to exchanges of propane or butane with mixtures of these. In particular, new considerations were developed bearing on the hazard of an occasional emission of carbon monoxide and flashback and blowoff possibilities. The new considerations involve using current requirements for approval of liquefied petroleum gas appliances. These requirements were used to predict allowable tolerances in chemical composition of liquefied petroleum gases for existing appliances. In addition, changes in gasline pressure were computed which may be substituted in place of fuel exchanges during testing of appliances,

Jan 1, 1962