Search Documents

By Dean H. Ambrose

This paper presents the results of a study using computer human modeling to examine machine appendage speed. The objective was to determine the impact of roof bolter machine appendage speed on the likelihood of the operator coming in contact with. A contact means two or more objects intersecting or touching each other, e.g., appendage makes contact with the operator?s hand, arm, head or leg. Incident investigation reports do not usually contain enough information to aid in studying this problem and laboratory experiments with human subjects are also not feasible because of safety and ethical issues. As an alternative, researchers developed a computer model approach as the primary means to gather data. By simulating an operator?s random behavior and machine?s appendage velocity, researchers can study potential hazards of tasks where it is not possible to perform experiments with human subjects. Analysis information is helpful to the mining industry in terms of making recommendations that reduce the likelihood that roof-bolter operators experience injury due to contact with a moving boom. Data analysis of roof bolter simulations show that the virtual-operator?s response time has little effect on the number of contacts experienced. Based on frequency and cross-tabulation, regardless of other variables, contact incidents were always greater when the boom was moving up, were always greater on the palm, and were always greater for the boom part of the machine. Also, regardless of boom speed, the 25th-percentile-sized operators experienced more contacts than did other operator sizes. Furthermore, regardless of boom speed, the 152-cm mine seam experienced more contacts than did other seam heights tested. Results of a survival analytic approach suggest that controlling the boom speed is the most important factor in determining the risk of an operator making contact. Based on the data collected, boom speed greater than 41 cm/s results in a substantial increase in risk to the roof bolter operator and should probably be avoided. At speeds less than or equal to 25 cm/s are associated with a more modest relative risk, which represents an acceptable level of risk. Also, at speeds between 25 and 41 cm/s, there could be a particular boom speed in this range at which a significant inflection point in the relative risk estimates occurs. Based on the results, this issue needs to be addressed by future research.

Jan 1, 2003

By George A. Savanick

The objective of this research is to develop a method for measuring the tensile strength at the interface between minerals in rock. These measurements reflect the strength of the attractive forces operating at crystalline interfaces in rock. Since these forces act in opposition to the forces set up in various rock fragmentation processes, measuring their strength may help in designing more efficient methods of rock fragmentation. The method developed for measuring the strength of intergranular adhesion in rock involves separating a bicrystal from the rock and determining the tensile strength at its solid-solid interface. This technique has been successfully applied to the study of quartz-feldspar interfaces separated from massive pegmatites, graphic granite, and the Rockville granite, yielding average tensile strengths of 5.86, 8.62, and 10.65 meganewtons per meter squared (MN/m2) (850, 1,250, and 1,524 psi, respectively). The data this technique provides indicate that the members of these bicrystals are strongly adherent. Examirtation of bicrystals broken at the crystalline interfaces indicates that the bonds responsible for this adhesion operate over only a portion of the interfacial area. This work conclusively demonstrates that tensile strength tests can be conducted on small selected areas; for example, grain boundaries in rock. The small-scale zones of strength or weakness determined in this way can be related to the overall strength of the rock.

Jan 1, 1972

By Fun-Den Wang

Rock bolting has become a major method of coal mine roof support because of its effectiveness, economy, and convenience. The polymeric-resin-bonded bolt has generally proved to be more effective than the mechanically anchored bolt, but the higher cost of the resin bolt limits it to applications where the increased support is essential. The low-cost high-early-strength cement grout developed during this project will encourage more widespread use of fully grouted roof bolts provided practical installation techniques can be developed. Laboratory tests of four types were performed on various rapid-set and accelerated cement products to find a material with properties suitable for replacing resins. A proprietary gypsum cement was ultimately used with good success. A field test of the cement grout was made in an operating coal mine. An intersection was bolted in the standard pattern with cement-grouted bolts and instrumented. A nearby resin-grouted intersection was also instrumented and observations were carried out in both intersections for 2 months. No substantial difference was found between the support provided by the cement and the resin.

Jan 1, 1976

By O. C. Blade

"INTRODUCTION This report on the properties of motor fuels sold through service stations in the United States is a continuation of a series of reports made in accordance with a cooperative agreement between the Coordinating Fuel Research (CFR) Committee of the Coordinating Research Council (CRC) 3/ and the Bureau of Mines of the United States Department of the Interior. The first of these reports presented data on motor gasolines sold during the winter of 1935-36. 4/ Further reports were issued describing motor gasolines sold during the succeeding summers and winters to and including the summer of 1941. 5/ No reports were made on motor gasolines Bold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-43, the semiannual reports were resumed. 6/The present report presents analytical data for 1,499 samples, representing the products of approximately 105 companies. As in previous surveys, the companies covered by the survey include both large and small suppliers. Conforming to former reports, the data cover three groups of samples - regular-price, premium price, and third-grade gasolines.As the number of analyses submitted for samples of third-grade gaso¬line are not considered adequate to represent this type of motor fuel, data for these analyses have not been averaged, but the individual items are tabulated. The number of samples, items and brands comprising each group is as follows; Regular-price, 872 samples, 266 items, and 83 brands; -premium-price, 584 samples, 217 items, and 72 brands; third-grade, 43 samples, 32 items, and 21 brands. The meanings of those terms as used in the surveys are as follows:"

Jun 1, 1945

By Alfred L. Ransome

The consumption of slab zinc in the United States increased sevenfold in less than a half century since 1900. Therein is reflected the innate characteristics of this versatile and nearly indispensable nonferrous metal whose use has grown at more than twice the rate of industrial production. The total metal consumption was substantially stimulated during the two World War periods, which were likewise marked by notable changes in use pattern accompanied by shifts in geographic distribution. This information circular summarizes basic data collected for many years by the Bureau of Mines, but in particular presents for the 1940-45 period details derived from the comprehensive slab zinc consumption survey inaugurated in 1940. The total consumption of slab zinc has been broken down into four major categories galvanizing, brass products, rolled zinc, and zinc-base alloys -- with minor applications grouped under a fifth heading, other uses. Ex- cept for the inclusion of zinc-base alloys with other uses before 1926, the above-named segregation has been shown for the entire period 1900-45. 11- though a substantial tonnage was taken by all groups in all years, there were large shifts in the use pattern in both World War periods. In both, the Allied Powers depended heavily on the United States for zinc-bearing products, especially those required by war industrius. The departures from usual uses were, however, much more marked during the second than in the first period, mainly because the United States could not have met the tro- mendously expanded war-materiel demands had the greater slab zinc needs of a period of high industrial activity been supplied. The geography of consumption is known in detail only for 1940-45. Even in that short period, substantial shifts are observable, largely the reaction from conversion to war production in 1940-41 and reconversion to peacetime consumption in 1945. However, there is so evidence of other shifts in consumption centers that appear to reflect longer-term develop- ments.

Feb 1, 1948

By Lester J. Crow

A preliminary survey was performed to investigate the impregnation of relatively weak, porous volcanic tuff and a relatively strong, dense sandstone with five different monomers. Increases in compressive strengths by factors of 2 to 5, and elastic moduli by factors of 2 to 3.5, are reported for natural rocks (tuff., sandstone, dacite), which were impregnated with five monomers (methyl methacrylate; chlorostyrene; 40 percent TMPTMA-60 percent styrene; 40 percent TMPTMA-60 percent chlorostyrene; 60 percent polyester-40 percent styrene); polymerization took place after monomers were forced into the rock. Impregnation was performed (1) by pressurizing rock specimens from one end, or (2) by a vacuum-soak operation. Polymerization was accomplished by either radiation or chemical initiation techniques. Strength improvement is dependent on (1) the type of monomer used, (2) the amount of polymer incorporated into the rock, and (3) the degree of water saturation of the rock. Water saturation strongly reduced the effectiveness of the method for the polymer systems tested. The more viscous monomers (for example, 60 percent polyester-40 percent styrene) were more effective in displacing the water from the rock, and compressive strengths of wet rock were doubled with these systems. Water saturations ranging from 25 to 100 percent of maximum saturation gave essentially identical results. Further tests on other types of mine rock; including shale and coal, are planned. Water-compatible polymer systems should be developed, or present systems should be suitably modified. For application to tunnel stabilization, design studies evaluating the improvement in rock strength and its influence on the support system are also recommended.

Jan 1, 1971

By W. A. Selvig

"The purpose of the investigation described herein was to determine how closely different laboratories can check one another in making determinations of fusibility of coal ash with the De Graaf electric coal-ash fusion furnace: how well duplicate determinations by the same laboratory will check, and how the results with the De Graaf furnace compare with those of the standard gas-furnace method of the American Society for Testing Materials.4Thanks are due the following laboratories who cooperated in this study by making fusibility tests with the Do Graaf electric coal-ash fusion apparatus: J. J. Brennan, testing engineer, Northern States Power Co.; R. E. Gilmore, superintendent, Fuel Research Laboratories, Canadian Department of Mines A. T. Leavitt, president, and W. Mueller, chief chemist, Hamilton By-product Coke Ovens. Ltd.; Edgar Stansfield, chief chemical engineer, Scientific and Industrial Research Council of Alberta. Canada; and H. S. Vassar, laboratory engineer, Public Service Electric and Gas Co.The ash-fusibility determinations by the standard gas-furnace method were made in the Coal Analysis Laboratory of the Bureau of Mines at Pittsburgh under the direction of H. M. Cooper, associate chemist. The investigation was made at the suggestion of A. C. Fieldner, chief engineer, Experiment Stations Division of the Bureau of Mines.Routine determinations of the fusibility of coal ash are made in the laboratories of the United States Bureau of Mines by the gas-furnace method. This method was standardized after considerable experimentation5 on the nature of the fusion of coal ash and the various factors which affect its determination. The method was subsequently adopted by the American Society for Testing Materials as one of its standard tests."

Jun 1, 1930

By Keith A. Heasley, Frank E. Chase, Christopher Mark

Deep cover retreat mining (overburden in excess of 750 ft) is an important emerging issue which will intensify in the future as the more easily mined shallow seam reserves are depleted. Analysis of Mine Safety and Health Administration (MSHA) statistics indicates that deep cover pillar recovery accounts for a disproportionate share of the underground coal mine roof/rib fall fatalities and injuries. Past research has shown that previously recommended Analysis of Retreat Mining Pillar Stability (ARMPS) stability factors (SF’s) may be excessive for deep cover pillar design. The objectives of this study were to evaluate the various methods and strategies by which panels, production pillars and barrier pillars are developed and extracted under deep cover, and to develop appropriate design guidelines. In the course of the research, 29 mines in 7 states were investigated to collect panel design case histories. At each mine site, underground geotechnical data were collected on the pillar line in order to document roof rock, coalbed and floor conditions. The analyses indicated that squeezes were the most likely failure mode where the depth was less than 1,250 ft, but bumps predominated in the deeper cover cases. Immediate roof rock quality, the ARMPS SF’s, and barrier pillar stability factors were all found to be important parameters in determining the outcomes of the case histories. Design guidelines, including suggestions for barrier pillars to isolate active panels from nearby gobs in bump prone ground, are also proposed.

By David D. Rabb

A report on location, sampling, assays, mineral examination, amenability leach tests, and evaluation of certain mine dumps in Mohave County, Arizona. Extractions of greater than 30 percent of the gold and silver were achieved during simulated heap leaching of selected mine dump material. Consumption of reagents was relatively low and results suggest leaching of prepared heaps is technically viable and could be economically attractive.

Jan 1, 1980

By James L. Hendrix

The applicability of a rotating drum with an attached trommel as a flocculation dewatering device of Florida phosphatic claywastes was studied. Several experiments were conducted in order to determine the important fabrication and operating parameters. Results from the experiments indicated flint the dosage of polyethylene oxide required to form a satisfactory product cake could be reduced by using the rotary drum, which introduces less shear stress into the fluid than a constant stirred tank mixer. It was found that the length of the mixer was the most important parameter. Increased length increased the retention time the flocs stayed in the mixer without dewatering. Such increased time decreased the stability of the flocs. Through analysis of residence time distribution data it was found that the longer mixers approached plug flow characteristics. Other important parameters were trommel length and rotational speed. Mixers from 10 cm diameter to 35.6 cm diameter were tested with good results.

Jan 1, 1982

By William H. Holley

Thirteen additional preservative/fire retardant systems were applied to Ponderosa pine and evaluated for flammability both before and after water leaching. The more promising four systems were given a thorough evaluation for flame spread, toxic gas and smoke density levels, resistance to decay, and compressive strength. The most promising system on the basis of history of usage in the mine, ease of application and low cost as well as overall performance is the Fyreprufe/ACC Albi 107A/ 144 combination. A survey of inspection tools and instruments, identified equipment which could be assembled into an inspection kit for use in determining the extent of decay and/ or impregnant retention levels in mine timber. A literature search identified those high fire hazard areas found in a typical mine. Timber and other wooden structures used in such areas should be treated with an acceptable fire retardant system. A survey of insurance companies revealed that the use of such treated timber in the mines would probably have little or no impact on the rate structure.

Jan 1, 1980

Development of automatic fire protection systems for large, mobile mine haulage equipment was initiated under Department of Interior's Bureau of Mines-FMC Corp. contract H0122053, "Improved Sensors and Fire Control Systems for Mining Equipment June 1972 to May 1973." After successfully designing and mock-up testing an effective economical automatic fire protection system, and after having demonstrated that the system could extinguish controlled fires on 100-ton capacity haulage trucks, USBM-FMC contract 110232059 was issued in June, 1973, to conduct further development and validation testing. This report documents technical progress and activity under the latter contract. Figure 1 shows areas of the two haulage trucks that were protected by the automatic fire protection systems tested during this program. Figures 2 and 3 are composites showing hardware and schematic diagrams of the systems tested.

Jan 1, 1974

By V. A. Marple

At the Twin Cities "lining Research Center (TCMRC) a project is underway to determine how varying the parameters of a coal-cutting process would affect the amount and the size distribution of the generated dust. The cutting parameters being investigated are the cutting speed, depth of cut and shape of the cutting, tool. To accomplish this research ft is necessary to collect and transport the coal dust venerated at the cutting tool to measuring instruments for analysis. The purpose of this contract was to develop and deliver a system of instruments for measuring the size distributions of the generated coal dust. The instruments employed are essentially those developed for particulate air pollution measurements (1, 2). The instrument system covers a particle size range of 0.005 to 20 microns and is capable of performing in situ measurement and presenting data in real time.

Jan 1, 1974

By L. G. Austin

"This paper is based on the development of the Maza-Austin technique for characterizing thousands of coal particles by approximate analysis of the major inorganic constituents Ca, Al, Si, K, Na, Fe and S in each particle. The technique has sufficient sensitivity to work on small volumes, is fast enough to handle large number of particles within a reasonable period of time, and consists of scanning electron microscopy combined with energy dispersive x-ray spectrometry (SEK-EDS). A computerized SEK-EDS system that allows the automated analysis of hundreds of coal particles per hour' is described. The analysis is based on the location and tracing of coal particles embedded in a polished specimen, the selection of sampling points on the traced particles, the collection of an x-ray spectrum from each sampled point for a defined period of time, and the processing of the x-ray intensity to calculate point composition using ZAF corrections. Procedures for correcting for dead time, background, detector efficiency and spectrum overlap are described. These corrections are essential if reasonably accurate analyses are to be obtained from unknown complex mixtures of the elements in a coal or fly ash particle. Examples are given. INTRODUCTION Coal is a complex mixture of organic and inorganic materials. The inorganic fraction is referred to as mineral matter (Gluskoter, 1978) but can occur in three modes: (i) an observable mineral species; (ii) as cations held by ion exchange to carboxylic groups; and (iii) in chelate complexes. The mineral matter content normally represents a significant proportion of a coal, with an average value of about 15% for US coals (Gluskoter, 1975). The standard methods of analysis of the mineral matter in coals are performed on a sample selected to represent the whole coal as closely as possible, and give the overall inorganic composition in the coal. Such analyses are of limited use for solving problems originating from the behavior of individual coal particles, whose compositions vary widely from the average value. This is particularly true in pulverized coal combustion, where the current methods of predicting the slagging and ·fouling potential of a coal are based on the bulk ash composition, but the fly ash particles which create the deposits originate from coal particles with large differences in mineral compo1ition. Some examples can be found where, in a comparison between two coals, the one with the smaller slagging potential according to the mean ash composition was the one that behaved worst in the furnace (Moza et al., 1980; Koza and Austin, 1983). The u1e of gravity fractionation to assess the slagging potential of pulverized coals has shown that conventional ASTM analysis is not sensitive to differences in the distribution of mineral matter when comparing coals (Borio and Narciso, 1979). Bryer (1979) concluded that coals should be examined for fouling and slagging potential by analyzing gravimetric and size-fractionated coal, preferably pulverized· and ground to the size expected at the mill outlet."

Jan 1, 1989

By M. C. Irani

This survey was conducted to determine the magnitude of the methane emission and control problem in U.S. bituminous coal mines. The resultant data indicate that the emission rate for any given coalbed depends primarily on the coal production rate and on mine depth, as well as on the nature of the coalbed and the surrounding strata. An excellent correlation was found between (1) the methane emission rate and (2) the product of coal production rate and mine depth for the mines in the Pittsburgh, Pocahontas Nos. 3 and 4, and the Illinois Nos. 5 and 6 coalbeds. The highest total emission rates found in U.S. bituminous coal mines were as follows, in million cubic feet per day: Monongalia County, W. Va., 39; Marion County, W. Va., 30.4; McDowell County, W. Va., 13.1; Washington County, Pa., 11.9; Greene County, Pa., 11.4; Buchanan County, Va., 21.6; Jefferson County, Ala., 10.3; and Franklin County, Ill., 6.6.

Jan 1, 1972

By R. F. Tenney

This report has been prepared because little detailed information has been published on the production and use of anthracite producer gas for industrial-process and brick-kiln heating. To obtain this information, an investigation was conducted by the Federal Bureau of Mines in cooperation with a building-brick manufacturer (firing both periodic and tunnel kilns with anthracite producer gas) and with a manufacturer of anthracite-gas producers. In addition to a study of available plant records, 2 weeks was spent in systematic observation and measurement during regular operation of the Hazleton Brick Co. plant, Hazleton, Pa., in July 1953. This report presents the results of this investigation and a description of producer and periodic-kiln equipment, operating procedures, and labor requirements. A summary of the conditions of producer and kiln operation is given for the 2-week observation and for the 11 preceding months. The two 10-foot standard anthracite-gas producers consumed 301 tons of Rice and Buckwheat No. 1 anthracite, as delivered, averaging over 13,000 B.t.u. per dry pound during the 2-week period, with a producer hot-gas efficiency of 95 percent, at an average gas offtake temperature of 5400 F. The yield of gas5/ of 153 gross B.t.u. per cubic foot amounted to 140,000 cubic feet per ton of fuel as fired, or 73,500 cubic feet per kiln heating hour, which was sufficient for kiln requirements.

Jan 1, 1960

By Philip Thompson

The Bureau of Mines investigated a selective flocculation-flotation technique to remove insoluble slimes from low-grade potash ore in a continous 45-kilogram-per-hour (100-pound-per-hour) process investigation unit (PIU). This research is part of the Bureau's program to improve resource recovery from low-grade ores. Results showed that 84 percent of the insoluble slimes were removed from an ore containing 5.5 percent water-insolubles and 14 percent K20 using a Bureau-developed, cationic flocculant-glycol ester-diesel oil reagent. Subsequent potash flotation recovered 75 percent of the potash in a cleaner concentrate assaying 56 percent K20. Concentrate leaching upgraded the product to market specifications of 60 percent K2O. An economic evaluation by the Bureau suggested that the rate of return on investment, after taxes, should be about 20 percent for such an enterprise.

Jan 1, 1980

By R. L. Stein

For the past several years, the Bureau of Mines has been actively engaged in developing two new oxygen self-rescuers through research contracts with private industry. These new oxygen self-rescuers are designed to be carried by a miner while he is at work and are used during emergency escape, supplying high-purity oxygen to the user and, at the same time, absorbing carbon dioxide (C02), The first of the two new self-rescue breathing devices is a 10-minute, self-contained apparatus developed by the Mine Safety Appliance Co, Size and weight of the unit are comparable to the currently used self-rescue devices. The second device, designed and developed by Lockheed Missiles and Space Corp., is 8. 4.5-lb package which supplies 1 hour of oxygen to the miner. Both devices have a canister which contains the oxygen-producing and CO2-absorbing potassium superoxide chemical, a breathing bag, a bite-type mouthpiece, noseclip, goggles, and hoses connecting the canister and mouthpiece. When needed in an emergency, the miner removes the outer protective cover and dons the unit. For both devices oxygen is immediately available once the mouthpiece is placed in the mouth. These two new units have received prototype approval from the National Institute for Occupation and Safety Health (NIOSH) and the Mining Enforcement and Safety Administration (MESA).

Jan 1, 1976

By L. C. IlsLey

In January, 1922, a conference relative to trailing cables for use with permissible mining machines was held at the Pittsburgh Experiment Station of the U. S. Bureau of Mines. At this conference it was recommended that the bureau take steps to investigate the rubber-sheathed type of cables and to bring about the establishment of a list of approved cables. Effective until such time as a complete investigation could be made, the bureau asked the several manufacturers holding approvals for mining machines to recommend cables for use with their machines. In general the cables recommended were tentatively approved. Due to the lack of available personnel, no actual tests of cables were made until mid-1927. Meanwhile a field investigation of trailing cables was made at 20 mines of three coal companies in western Pennsylvania, and samples of cables were obtained from the manufacturers for laboratory tests. Twenty-five samples of the concentric-type cable, representing the product of five manufacturers, were obtained for the tests. These cables were of four sizes, as follows: 3 cables of No. 2 B & S gage, 17 cables of No. 3 B & S gage, 3 cables of No. 4 B & S gage, and 2 cables of No. 6 B & S gage.

Jan 1, 1929

By A. E. Gooch

The Bureau of Mines conducted research in an attempt to provide a more sound basis for recommending improved artificial support during deepening of the main shaft of the Lucky Friday mine in the Coeur d'Alene mining district of northern Idaho. Field measurements of closure across the short axis of the 13-by 26-foot shaft were as high as 16 inches. Elastic/plastic finite-element (F/E) analyses were made, reducing the values of large-scale in situ rock mass properties until field closure measurements generally corresponded to displacements in the F/E analyses. Resulting plots of rock mass displacements, stresses, and areas of plastic failure display the results of creating openings (shaft, in this case) in deep mines in difficult ground conditions requiring artificial support.

Jan 1, 1976