Search Documents

By M. D. Aldridge

The results of a two-year research effort aimed at improving communication systems in coal mines is reported. A review of communication methods presently used in coal mines is presented. Theoretical and-experimental results of a four pronged effort in the areas of (1) through-the-earth propagation, (2) paging system design, (3) improvement of wired telephone systems, and (4) carrier current systems are described. Auxiliary systems not included in the above are considered briefly. Various conclusions are drawn in light of practical constraints and the needs of the mining industry. The study clearly demonstrated the need for nine communications to be designed on system basis. The viability of new technology for providing reliable mine communication for improving mine safety and operating efficiency is shown.

Jan 1, 1973

By Russel R. Bohn

The objectives of this study were to: (a) determine the state of the art for the control effectiveness of various chemical dust suppressants, (b) field test the effectiveness of the dust suppressants, and (c) develop technical guidelines for selecting and implementing cost effective tailings pond dust control programs. Chemical stabilizers evaluated under field conditions were: Coherax, Calcium Lignosulfonate, Nalco 656, 655, and Magnesium Chloride. Testing in the field utilized a portable field in-situ wind tunnel. The wind tunnel was placed on the tailings surface and simulated wind speeds of up to 80 mph were used to determine wind erosion threshold velocities. Emission rate testing was performed with the wind tunnel through the use of a real-time cascade impactor. A control cost effectiveness evaluation was performed to determine how efficient the chemical stabilizers were on a dollars expended per acre basis.

Jan 1, 1983

By John R. Rhodes

The objective of this project was to investigate the feasibility of analytical techniques potentially capable of determination of Mg, Al, Si, S, Ca and Fe in 1 to 2 mg samples of respirable coal mine dust, in a total analysis time of not more than 10 minutes per sample, using equipment capable of being truck mounted for field-laboratory operation. It was not essential that the technique be non-destructive, but the chosen technique is, and this enables the analysis to be performed directly on the 37 mm diameter membrane filter on which the respirable dust sample is normally collected. The sensitivity requirements are therefore quoted in terms of the units of measurement, µg/cm2. The detection limit (3o of the background criterion) should be 0.5 µg/cm2 or less. The precision should be 5% or better, at concentrations above which the detection limit is not the determining factor.

Jan 1, 1972

By Steven A. Hawkins

This report details the conduct and results of a 5-month study to collect data on the use of steel support for ground control in European underground coal mines. The report summarizes European steel support design practices and describes the applicability of steel supports to U.S. mining conditions.

Jan 1, 1980

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

C THRM 1 C CALCULATION OF MINE HEAD LOSSES FROM ALTIMETER SURVEY DATA TURN 2 C PENNSYLVANIA STATE UNIVERSITY - MINERAL ENGINEERING DEPARTMENT THRM 3 C THRM 4 C THRM 5 C THIS PROGRAM CALCULATES PRESSURE LOSSES USING THERMODYNAMIC RELATION- THRM 6 C SHIPS BASED ON POLYTROPIC FLOW BETWEEN STATIONS. FOR REFERENCE SEE THRM 7 C "A NEW TREATMENT OF MINE BAROMETER SURVEYS" BY M. J. MCPHERSON IN THRM 8 C 'THE MINING ENGINEER' NO. 109, VOL. 129, P 23. THRM 9 C THRM 10 C THRM 11 C THRM 12 C IDENTIFICATION OF ARRAYS THRM 13 C NOTE THE PROGRAM HAS BEEN DIMENTIONED FOR FOURTY (40) DATA POINTS THRM 14 C BASEC(6;2) BASE INSTRUMENT TEMPERATURE CORRECTIONS THRM 15 C TRAVC(6,2) TRAVERSE INSTRUMENT TEMPERATURE CORRECTIONS THRM 16 C BASER(I) BASE INSTRUMENT READING THRM 17 C TRAVR(I) TRAVERSE INSTRUMENT READING THRM 18 C TDRY(I) DRY BULB TEMPERATURE AT TRAVERSE STATION THRM 19 C TWET(I) WET BULB TEMPERATURE AT TRAVERSE STATION THRM 20 C ELEV(I) ELEVATION AT TRAVERSE STATION THRM 21 C VEL(I) AIR VELOCITY AT TRAVERSE STATION THRM 22 C TBDRY(I) DRY BULD TEMPERATURE AT BASE STATION THRM 23 C BASC(I) BASE READING CORRECTED FOR INSTRUMENT TEMPERATURE THRM 24 C TRAV(I) TRAVERSE READING CORRECTED FOR INSTRUMENT TEMPERATURE THRM 25 C BBASE(I) TEMPERATURE CORRECTED BASE READING IN BAROMETRIC THRM 26 C PRESSURE THRM 27 C BTRAV(I) TEMPERATURE CORRECTED TRAVERSE READING IN BAROMETRIC THRM 28 C PRESSURE THRM 29 C BTRAVS(I) BAROMETRIC TRAVERSE READING CORRECTED FOR ATMOSPHERIC THRM 30 C CHANGES THRM 31 C RELHUM(I) RELATIVE HUMIDITY THRM 32 C ASW(I) AIR SPECIFIC WEIGHT TURN 33 C R(I) GAS CONSTANT FOR MOIST AIR THRM 34 C STPRES(I) STATIC PRESSURE CHANCE BETWEEN STATIONS (I) AND (1-1) THRM 35 C TOPRES(I) TOTAL PRESSURE CHANCE BETWEEN STATIONS (I) AND (I-1) TURN 36

Jan 1, 1977

By M. P. Dalton

This paper which describes the milling practice at the Morning concentrator of the Federal Mining and Smelting Co., Mullan, Idaho, is one of a series being prepared by the Bureau of Mines. ACKNOWLEDGMENT The author wishes to acknowledge the assistance given by H. G. Washburn, general manager of the Federal Mining and Smelting Co., and by C. S. Price, assistant mill superintendent, in the preparation of this paper.

Jan 1, 1932

By H. J. Sloman

Mining laws of the several coal-producing Stat e with respect to safety catches on mine cages and their testing are extremely variable and generally indefinite in scope. The most specific requirements are contained in the Coal Mining Laws of Washington,3/ as follows:

Jan 1, 1944

By Alfred L. Ransome

The plan to develop a standard system of names and definitions of regions and districts in Alaska was borne of the need for a tool to use in statistical and economic studies of the mineral industry of the Territory. The purpose of this report is to present to the mineral industry, and to those individuals interested in the mineral or allied industries in Alaska, the system used by the Bureau of Mines in connection with its legal function of collecting and disseminating mineral statistics. It is hoped that the specific descriptions given will result in a more complete understanding of what is meant by the regional and district names that appear in publications of the Bureau of Mines relative to the mineral industry of the Territory. Problem of Standardization of Names and Definitions The question might be asked, does the naming and defining of regions and districts in Alaska present a problem relative to the establishment of a standard? Is it necessary to establish a standard?

Jan 1, 1954

By M. E. Tyrrell

This Bureau of Mines investigation was made to determine the possibilities of using Florida beach-sand concentrator wastes in ceramic products. Sands used in the investigation originated in the Trail Ridge area of Florida, where continued operation of processing plants for recovering titanium minerals promises a dependable source of raw materials. Three general classes of ceramic products were studied, namely: (1) Structural, (2) refractory, and (3) electric-furnace slags.

Jan 1, 1956

By D. Harringtong

"There has been much writing and argument on the subject of giving bonuses to miners, quarrymen, metallurgical and chemical workers, and others as a stimulus for safe work and for work safely done. Theoretically, everyone should be careful and should not need monetary or any other type of encouragement for the prevention of accidents; as a. fact, few people are careful, and this is primarily the reason way many if not most accidents occur. A bonus, however, is not simply money given away by an employer; it must be earned, so to speak, before it becomes due; in other words, if the standard established is not reached, no bonus is paid, and in many cases some disciplinary action is taken.The United States Bureau of Mines Is asked from time to time for suggestions for rewards to mine workers who have a good attitude toward working safely or who need some stimulus to cause them to make greater or more earnest efforts toward safety for themselves and their co-workers. A recent inquiry prompted the collection of data on some safety bonus systems from reports of this bureau's field engineers and others, and some of these Now given. Bonus practice at both coal and metal mines is included because a system used at metal mines is generally adaptable to coal mines; in fact, in numerous cases, bonus systems recently started at some coal mines are based on systems in vogue and giving satisfaction some metal mines; in-some instances, also, metal mines have been able to get good suggestions from coal mines or from the cement or petroleum industries. it .should be understood that a bonus, even as applied to the encouragement of safety, does not necessarily mean payment of money; in fact, some successful bonus systems have in them no direct money exchange; hence, the bonus as treated in this paper is that defined as ""Something given in addition to what is ordinarily received by, or strictly due to, the recipient.""Acknowledgment is given here to members of the safety division of the Bureau of Mines who sent in some of the information here presented; to the Engineering and Mining Journal and Mining Congress Journal, from which some items were abstracted; to various mining officials who gave data in one form or another; and to M. von Bernewitz, of the United. States Bureau of lines who aided in framing parts of this paper."

Jun 1, 1932

By Thomas M. Barczak

The initial Support Technology Optimization Program (STOP),Version 1.0, was released at the 19th Ground Control Conference. This original program has since been updated to Version 2.3 which was released in May, 2001. This paper describes the additional features of Version 2.3, focusing primarily on the following three aspects: (1) including uncontrolled convergence into the design requirements for standing roof supports, (2) the addition of design procedures for cable bolts as an alternative secondary roof support, and (3) the addition of new standing roof support technologies. Another new feature which should facilitate the development of design criteria for standing roof support is the capability to define ground reaction curves through convergence measurements alone without having to make support loading measurements. There are several other new features provided in Version 2.3 which are only briefly addressed in the paper. These include: (1) additional graphics capabilities to facilitate rapid assessment of support comparisons, (2)an East-West designation for support selection to more accurately provide cost and support availability data, (3) additional safety measures including a safety factor to identify support design near the peak support capacity, checks to see if the support dimensions comply with aspect ratio requirements, and a measure of roof coverage for the design layout of the support system. These new features of STOP provide more capabilities to design and analyze secondary roof support systems for conditions which could not be fully analyzed in the original version of the program.

The condition of the domestic mining industry is obviously affected by the cycles in general business conditions. This study, the results of which are presented in a series of 78 charts, attempts to examine the interrelationships between the general business indicators and the major statistical measures for the base-metals industries during the cycles in the United States economy following World War II. For these industries the cyclical problem is perhaps less acute than the secular-trend problem. However, short-run fluctuations in production and employment do have very important impacts upon the welfare of the regions which derive a significant portion of their income from base-metals mining and processing industries. Any information concerning the normal patterns of development as the industries enter into a cyclical recession will permit better forecasts and perhaps help promote measures to alleviate the distress that occurs. Also, a systematic study of the comparative movements among the statistical measures during a series of cycles can bring to the fore the economic causation involved, and perhaps, after intensive study, can lead to a better method of short-range forecasting for these industries. This study has not fully achieved these aims. However, observations which significantly aid the interpretation of the current monthly statistics on these commodities are made, and some very general conclusions are drawn. The charts are presented so the interested people can examine them and draw additional conclusions. The charts refer specifically to cyclical analysis. The technique of indexing each cycle to its turning point effectively subordinates the longer term trend movements of the data. Thus, certain general conclusions flowing from this study and from the continuing economic research of the Office of Chief Economist will aid the reader by clarifying the frame of reference within which the charts should be examined.

Jan 1, 1961

By A. M. Poston

Introduction of radioactive elements into ore samples and/or pregnant liquors and radiometric tracing thereof have greatly improved control of fusion and extraction studies on beryllium ores and products. Extractive metallurgical research on beryllium, normally guided by the usual laborious analytical methods, is both costly and slow. Recognition of this problem by the Bureau of Mines led to the development and application of radioisotope tracer techniques" as a substitute for chemical analysis at the Salt Lake City Metallurgy Research Center, The result was that much faster progress at significantly lower cost was achieved. This report discusses the problems encountered and resolved in using radioactive tracers and radiometric methods, defines the conditions and techniques for their effective use, and delineates the limitations and flexibility inherent in applying such methods in laboratory-scale beryllium research.

Jan 1, 1962

By H. A. Doerner

"During the year which has passed since the last progress report on reduction of zinc by natural gas,3 the laboratory experiments on this investigation have been completed. In this concluding report, the whole subject will be reviewed and additional data presented.Chemical ReactionsIn a thermodynamic study of zinc smelting, Maier 4 discussed the use of methane for reducing zinc oxide, and predicted equilibria at various temperatures for the sore important reactions. The study has been extended to include the following list.Maier predicted that 870°C. would be the critical temperature above which reaction (1) would take precedence over reaction (2) and that reaction (1) at equilibria would be substantially complete at or above 927°C. A subsequent papers described experimental verification of these predictions and gave data on reaction rates under various conditions.It methane is passed through a heated bed of zinc oxide at a low enough rate reactions (1), (3), and (4) reach an equilibrium which can be expressed by reaction (10). The equilibrium concentrations for the products of this reaction in the temperature range 900° to 1100°C. were calculated by applying the thermodynamic constants to the stoichiometric relations. 6 The results of these calculations are listed in table 1 and shown graphically in figures 1, A and B. These data have major importance, and experimental work has shown that they are subtantially correct."

Dec 1, 1934

In This Chapter [Finding the dust source Ventilation and dust collector malfunctions Upgrading the dust controls Design stage ventilation planning ] This chapter explains how to reduce respirable dust76 in hard-rock tunnels during excavation by using tunnel boring machines (TBMs). The first steps in combating a dust problem are to take dust samples to pinpoint the source, check the ventilation system, and check the dust collector. If the ventilation system and dust collector are operating properly, then other dust controls such as water sprays and conveyor belt scrapers must be upgraded. For tunnels in the design stage, recommended air quantities are provided. FINDING THE DUST SOURCE AND LOOKING FOR VENTILATION MALFUNCTIONS [The first steps in fighting a dust problem are to take dust samples to pinpoint the source, check the ventilation system, and check the dust collector. Without knowing the exact source, efforts to reduce dust are hit-and-miss (mostly miss).] Taking samples to pinpoint the dust source. In tunnels with high levels of airborne dust, the first task is to pinpoint where the dust enters the airstream. Most dust originates from rock breakage at the tunnel face, but the location where this dust enters the airstream can vary. Dust can leak from behind the TBM face shield, from gaps in the ventilation duct, or from a mal-functioning dust collector. It can be entrained into the air from the muck on a moving conveyor belt. It can even be shaken loose from the underside of the belt as it passes over the idlers. As a start, to locate the dust source, dust samples and air quantity measurements should be taken at the following locations:

Jan 6, 2003

By Wilbur L. Webb

An electrically powered methane sampling system for application on mining machines was designed, fabricated and laboratory tested. The system will sequentially draw sample air at a controlled rate from up to three machine positions across the mine face and deliver the air to either an approved methane monitor, methanometer or flame safety lamp. The prime considerations in the design were to provide an intrinsically safe, water and dust resistant control box and an explosion-proof power box capable of being operated from the various mining power sources. The power box contains an internal battery that provides operating power prior to mining machine start-up and alter machine shut-down. The internal battery is recharged automatically when mining machine power is available.

Jan 1, 1977

By G. A. Apell, E. G. Howe, S. W. Hazen

"INTRODUCTION As a small amount of manganese was produced from the Lake Valley mining district of Sierra County, N. Mex., during the First World War, the district was reexamined in March 1941 by John H. East, Jr., an engineer of the Bureau of Mines, as a possible source of manganese for use during the Second World War. Preliminary examination indicated a substantial reserve of 25 percent ore, so it was recommended that an exploratory program of mapping and sampling be undertaken by the Bureau.The program was started in the fall of 1941 and was completed the middle of 1942. The project 3/ was divided into two parts: The first, an underground sampling program, formed the basis for the second, or churn-drilling program. Mapping and sampling of old underground workings were begun in October and finished in November 1941, whereas churn drilling was begun in February and completed in June 1942."

Jun 1, 1947

By McHenry Mosier

This paper describes the practice in diamond drilling blast holes and discusses the relative merits of this method as compared with drilling by percussion rock-drills at eastern magnetite mine A. The rooke that were drilled included: (1) Gneiss; (2) sohist; (3) crystalline limestone; and (4) granular masses of magnetite. The principal stoping methods were: (1) Sublevel open stoping and (2) inclined room-and-pillar. Diamond drilling was used in the sublevel stopes and in some of the large pillars in an old section of the mine. Experimental work on diamond drilling blast holes began in 1943. Drill- ing proved difficult owing to the occurrence of fingers of extremely hard barren rock in the magnetite ore. All diamond drilling was contracted to a firm that furnished everything necessary for drilling except compressed air and water. In most instances the diamond-drill machine is clamped directly to a 3.5-inch column to reduce vibration. For drilling in floor pillars in open stopes, the drill was set on a demountable, sectionalized steel, frame with four legs carrying a 20-foot, 3.5-inch, extra-heavy pipe. "Both coring and noncoring bits were tried. In holes drilled with a cor- ing bit, the core was ground into sludge as the bit advanced so that it was unnecessary to delay drilling for pulling core. Data on tests with several types of bits are given as well as some oper- ating results. A direct comparison of costs between diamond drilling and percussion drilling was not available. The advantages of diamond drilling blast holes at mine A included: (1) Safer working conditions in open stopes. (2) The recovery of additional ore. (3) A reduction in the amount of stops development.

Dec 1, 1946

By A. J. Kraemer

This paper is the third and concluding report of the results of the United States Bureau of Mines twenty-third semiannual survey of motor fuel marketed in the United States. The first paper, reporting data relative to gravity, vapor pressure, and distillation range of the samples, was published as Report of Investigations 3129. The second report dealt with the data of the twenty-third survey in accordance with the revised specifications for United States Government Motor Gasoline. These data were published as Report of Investigations 3142.

Jan 1, 1931

By A. J. Kraemer

This paper is the second and concluding report of the results of the Bureau of Mines' twenty-second semiannual survey of motor fuel marketed in the United States. The first paper Was published as Report of Investigations 3063 and reported data relating to gravity, vapor pressure and distillation range of the samples. The present paper deals particularly with results of the determination of copper strip corrosion (method 530.22), color (method 10.11), sulphur content by the lamp method, copper dish evaporation residue (method 530.1), and "gum" content as given by the steam-oven method as developed by the Bureau of Mines. The price at the time the sample was taken and the tax are also stated for each sample. The sample numbers used throughout this report are identical with those used in Report of Investigations 3063; for example, No. 225 of this report is the same sample as No. 225 of Report of Investigations 3063. This is the first semiannual motor gasoline survey of the Bureau 6f Mines in which some data were obtained on antiknock values for samples collected in the survey. The Bureau of Mines is not provided with equipment for making these tests in its own laboratories, but composite samples were tested in the laboratories of the Bureau of Standards and the report on these samples is given as a supplement to this paper (pp. 11 to 14).

Jan 1, 1931