Search Documents

By J. W. Town

The Bureau of Mines determined the physical properties of southeastern Idaho phosphate fines as related to mineral composition, particle size and liberation, beneficiation, and potential use in structural clay products. The phosphate mineral in the fines was identified by unit-cell dimensions to be essentially the same as the phosphate mineral fluorapatite identified in the coarser sizes. The mean particle frequency as determined by electron-microscopy and pipet-analyses was between 0.5 and 0.2 micron. Liberation of the phosphate could not be definitely determined because of the weathered condition of the minerals and their extreme fineness. No beneficiation scheme was developed that would concentrate the phosphate into a marketable fertilizer product; therefore, forming and firing tests were made to demonstrate that the fines can be used to manufacture structural clay products.

Jan 1, 1968

By E. G. King

As low-temperature heat-capacity and entropy data were available for only one sesquisulfide (cerium sesquisulfide), it appeared desirable to augment the information for this class of compounds by measuring the sulfides of antimony and indium. In addition a pressing need existed for data on indium sulfide to supplement vaporization studies in progress in the Department of Mineral Technology, University of California. This Bureau of Mines paper reports low-temperature heat-capacity measurements and entropy evaluations at 298.15° R. of antimony sesquisulfide of stoiehiometric composition (Sb2S3) and of indium sesquisulfide which was somewhat deficient in sulfur (In2S2.93). The data for the latter substance were adjusted to correspond to the stoichiome tric composition (In2S3 ) . Indium sesquisulfide has a lower entropy at 298.15' K, than either antimony sesquisulfide or cerium sesquisulfide, in line with the higher atomic density of the indium compound.

Jan 1, 1962

By S. L. Gerhard

In the United States the performance characteristics of permissible explosives are controlled by routine tests, which include firing the explosive into a gallery filled with a methane-air mixture. These tests are made by the staff-of the Explosives Division of the Bureau of Mines and are similar, in general, to those employed in other countries. This control has helped to reduce the frequency of accidents involving the ignition of firedamp by explosives but has not clarified the basic causes of the ignition. To advance this control and to minimize potential hazards further, this fundamental knowledge is needed. Some of the results of recent research on the causes of the ignition are described herein. NATURE OF THE PROBLEM When an explosive ignites firedamp in the gallery tests, the source of the ignition must be one or more of the emissions from the steel borehole. It has been accepted generally that these emissions are (1) particles, (2) the shock wave, and (3) hot gases and flames. Photographs show that the shock wave emerges from the borehole first, followed closely by hot gases. At first the velocities of these are high and approximately equal, but the velocity of the gases decreases more rapidly than that of the shock wave, and by the time the reactions causing the flame are complete the shock wave travels in an otherwise undisturbed medium. The particles are originally enveloped in the hot gases but some soon begin to break through and eventually out-distance the shock wave. The approximate geometry of these emissions about 1 millisecond after the shot is fired is illustrated in figure

Jan 1, 1939

By D. B. Lovett

The work described in this report was directed toward identifying and devising methods to minimize the previously observed variability between working level hour exposures and the alpha particle track densities resulting on Track Etch films exposed to mine atmospheres containing radon and radon daughters. The disequilibrium between radon and its daughters was shown to directly affect this Track Etch film calibration factor. The wide range of disequilibrium states possible in mine situations amply explains the variability in the previous tests. A file of published mine atmosphere composition data was compiled and was used, along with atmospheric compositions derived from several theoretical models ref the atmospheric behavior, to evaluate the variability of several dosimeter configurations and concepts. A nonlinear, iterative regression analyse; was formulated that successfully predicted working levels to within 8 to 10% from only the alpha particle activities (Rn, RA, and RaC') data such as are obtainable from Track Etch films over a wide range of disequrlibrium conditions. A model expressing atmospheric concentrations as a function of radon source strength, plate out rate factor, ventilation rate and the fractional re-entry by recoil of previously platted-out daughters was derived and used in the regression program in addition to preparing a set of reference tables and graphs showing the disequilibrium behavior of the atmosphere. Other factors that can affect the Track Etch Film response writ considered and shown to he less crutial than the disequilibrium state. The results of a series of exposures of a dosimeter concept fixture in the Denver Mining Research Center radon chamber air presented and discussed.

Jan 1, 1976

By Frederick C. Tompkins

A complete service system was established for the monitoring of personnel exposure to N02 based upon the use of passive dosimetry. This system is structured such that minimum effort is required of the user: manufacturing, analysis, reporting, and record keeping functions are provided by the service organization. A field evaluation program was carried out in a dieselized mine to assess the performance of two passive dosimeters, the Walden GASBADGE TM dosimeter, and a tubular dosimeter developed at New York University. Side-by-side comparisons were carried out to evaluate dosimeter suitability for monitoring in the field, and to assess relative accuracy characteristics.

Jan 1, 1976

By C. B. Kenahan

The Bureau of Mines is developing methods for reclaiming the metal and mineral values contained in municipal incinerator residues. This report describes the first phase of the research, in which reliable methods for sampling and analyzing municipal residues were established and the composition and characteristics of the residues were determined. Samples were obtained from a variety of grate-type furnaces and also from a rotary kiln furnace. The samples were processed on a batch basis and separated into their natural categories by a variety of methods including screening, magnetic separation, air separation techniques, and handpicking. The main components of the residues were determined to be metal and metal oxides, glass, and ash.

Jan 1, 1968

By John Nagy

Dust explosion data obtained in laboratory studies by the Bureau of Mines are presented for activated carbon, asphalt, charcoal, carbon black, coal, coke, gilsonite, graphite, lignite, miscellaneous carbons, pitch, tunnel dust, and mixtures of these materials with other ingredients. The explosion hazard is shown to increase as the volatile content of the dusts increases.

Jan 1, 1965

By Thomas K. Matson

The coal reserve base in the Western United States is presented for coalbeds amenable to extraction by underground mining methods. The Federal Bureau of Mines has abstracted data on the quality and quantity of coal resources/reserves from numerous State and Federal publications and modified such data as necessary to allow computer storage and retrieval. Tonnages are compiled by State, county, coalbed, and rank, and allotted to sulfur categories by statistical apportionment. The coal reserve base in those States west of the Mississippi River, amenable to underground mining, is estimated to be approximately 131 billion tons. Of this total, about 30.8 billion tons are bituminous coal, 100.2 billion tons are subbituminous coal, and 126.4 million tons are anthracite. Lignite is not considered for underground mining in this report. Included in this report is a glossary of terms applicable to a classification system for coal resources and reserves as jointly defined by the Bureau of Mines and U.S. Geological Survey. The purpose of this system is to provide for direct comparison or compilation of various resource/reserve data.

Jan 1, 1975

By F. A. Penning

Improved skips, with lightweight cylindrical bodies, have made a significant contribution to advancing mine hoisting technology. New concept skips of aluminum bodies with rubber lining; fiberglas bodies with polyurethane liners have been designed and fabricated for field testing at an operating mine. New design, adjustable guide rollers have shown improved ride characteristics with noticeably less wear. Major reductions have been made in stress levels and stress concentrations. Field experience has shown the practicality of the approach. Guide alignment has been measured using the Guide Alignment Measuring System (GAMS). Analysis has been applied to interpret the data. Field measurements in an operating shaft and a test tower have shown the agreement in data from GAMS and plumb wires. Reproducibility has been demonstrated. The data are useful to realign shafts, to use as s maintenance tool, and to evaluate the maximum safe hoisting speeds. The surveys are made at several hundred feet per minute and the system is self-contained. Dynamics of skip-guide interaction has been analyzed using the computer program SKIP II. The effects of speed, weight, type of guides, kind of misalignment have been studied. Resonance has been demonstrated and factors that eliminate resonance have been identified. Data from the GAMS surveys are applicable to the SKIP II program. Interaction between the hoist rope and the mine conveyance has also been studied. Computer programs and closed-form solutions are presented. Economic impact of lightweight skips is presented for an existing mine and for a new mine. Reduction in rope size has a profound effect when using a lightweight skip for the same capacity. Increased productivity can be realized by keeping maximum rope pull the same while increasing skip capacity. Examples and charts project the significant savings in capital expenditure for new installations.

Jan 1, 1985

By R. L. Rough

Photoelastic, wire resistance, and borehole-deformation gages were used to measure the in situ strains when an outcropping Black Hand Sandstone Formation in Hocking State Forest, Hocking County, Ohio, was overcored to stress-relieve the surrounding sandstone. Strains transmitted to the photo-elastic gage did not produce isochromatic patterns suitable for quantitative analysis. Strain readings from the wire resistance gage indicated tensile-strain loading during overcoring; readings from the strain-gage bridges in the borehole-deformation gage indicated compressive-strain relaxation during overcoring. The magnitude and orientation of the computed stress fields obtained from both gages were comparable when the corresponding tensile and compressive elastic moduli were applied. Stresses computed from deformation and resistance gages at depths to 5 feet showed the maximum stresses to range from 1.042 to 2.121 times greater than the minimum stresses. The bearings of principal stresses calculated from the deformation gage readings varied between N 61° E and N 83° E; the wire resistance strain gage bearing computations varied between N 68° E and N 82° E. Measurements of in situ strain in sandstone were shown to have promise but to require further development in field technique that could likely be achieved through experience.

Jan 1, 1971

By E. K. Stanek

This research study was performed on a case study basis and can be divided into two parallel thrusts: electrical and thermal energy conservation. Energy consumed annually in mining and refining operations represents about 6% of the 80 quadrillion Btu's consumed nationally. In the electrical portion of the study, five areas were addressed: optimal dispatching of on-site generation, high-efficiency motors, conductor selection, power factor correction, and high efficacy lighting. In the case study mine which has a multiple unit on-site generation system, optimally dispatching units can save significant energy. The other four methods are difficult to justify on a retrofit basis due to capital costs. In the thermal portion of the study, a thermodynamic analysis was performed on the reverberatory smelting process possible areas of energy conservation were identified as radiation and convection heat losses from the furnace arch and the dumping of high energy content smelting slag. It has been shown that materials currently available can provide the means of reducing heat loss from the reverberatory furnace. It has also been shown that a significant amount of energy may be recovered from the slag. However, these are both subject to further study and validation.

Jan 1, 1982

By S. L. Gerhard

In the United States the performance characteristics of permissible explosives are controlled by routine tests, which include firing the explosive into a gallery filled with a methane-air mixture. These tests are made by the staff of the Explosives Division of the Bureau of Mines and, are similar, in general, to those employed in other countries. This control has helped to reduce the frequency of accidents involving the ignition of firedamp by explosives but has not clarified the basic causes, of the ignition. To advance this control and to minimize potential hazards further, this fundamental knowledge is needed. Some of the results of recent research on the causes of the ignition are described herein. NATURE OF THE PROBLEM When an explosive ignites firedamp in the gallery tests, the source of the ignition must be one or more of the emissions from the steel borehole. It has been accepted generally that these emissions are (1) particles, (2) the shock wave, and (3) hot gases and flames. Photographs show that the shock wave emerges from the borehole first, followed closely by hot gases. At first the velocities of these are high and approximately equal, but the velocity of the gases decreases more' rapidly than that of the shock wave, and by the time the reactions causing the flame are complete the shock wave travels in an otherwise undisturbed medium. The particles are originally enveloped in the hot gases but some soon begin to break through and eventually out-distance the shock wave. The approximate geometry of these emissions about I millisecond after the shpt is fired is illustrated in figure

Jan 1, 1939

By John E. Pahlman

The Bureau of Mines investigated the feasibility of removing heavy metals from mineral-process waste streams by precipitation with lignochemicals and humic acids. Lignochemicals are by products from the paper industry, while humic acids are obtained by caustic treatment of peat, subbituminous coal, and lignite. These high-molecular-weight organic materials have many functional groups, which can coordinate and form innercomplex salts with heavy metals that are crystalline precipitates. Filtering of a humic-acid-or lignochemical-treated solution or waste stream containing these precipitates removes the heavy metal sequstrates. Tests were conducted with two lignochemical samples, three humic acid samples, lime (CaO), and sodium hydroxide (NaOH) in which increasing amounts of these additives were reacted with 50 mL of solution containing Fe3+ , Al3+, Cr3+, Pb2+, Cu2+, Cd2+, Zn2+, Co2+, Ni2+, Mn2+, and Hg1+. At the appropriate pH, greater than 90-and 99-pct removal was achieved for these 11 heavy metal ions from the 10-and lOO-ppm solutions, respectively, using lignochemicals and humic acids. Removal efficienC)' with these organic materials is better than that with CaO, especially for the more toxic ions, Hg1+, Cd2+, and Pb2+. Unlike the precipitates formed with NaOH or CaO, those with lignochemicals and humic acids are compact and noncolloidal. The volume of their sludge is sharply lower than that of the finely dispersed lime or soda precipitates; thus, their removal in settling tanks or by simple filtration is enhanced.

Jan 1, 1988

By Floyd R. Anderson

Noise control of existing pneumatic drills is difficult and runs into cost, performance and weight penalties. A need exists for a start-from-scratch approach for quiet pneumatic rock drills. The designs based on Leavell Principles which has been successfully used in demonstrating a quiet and vibration free paving breaker, is the concept chosen here. This report shows the feasibility of a quiet stoper for drilling roof bolt holes in coal mines. The work is directly applicable to pneumatic percussive rock drills. The report shows an oscillator based on patented Leavell concepts which results in a vibration free tool and noiseless exhaust. Dynamics of the oscilator is analyzed. Independant rotation of drill rod is provided by an air motor (screw expander) and flushing of cuttings is accomplished by an air ejector in a compact lower housing. The feasibility of no exhaust noise, low drill machine noise, and vibration free casing is discussed.

Jan 1, 1977

By M. M. Gilkey

Pegmatites in Colorado occur for 150 miles along the Front Range (eastern-most range of the Rocky Mountains) from Larimer County on the north to Canon City on the south, and west into the Gunnison area. Many of the deposits have been classified. Minerals found in the various dikes include beryl, scrap and possibly punch mica, lithium-bearing minerals, columbite-tantalite, feldspar, and several rare minerals. Pegmatites are abundant in the Crystal Mountain district in Larimer County. About 5 miles south of the Crystal Mountain district and often identified with that district is the Hyatt pegmatite area. The Hyatt Ranch deposit has attracted particular attention because of the comparatively high beryl con-tent of the upper part exposed in opencut workings.

Jan 1, 1960

By George H. Holmes

This paper is one of a series on mining methods and practices published by the Bureau of Mines. It describes quarrying methods and crushing practices of the U. S. Lime. Products Corp. at its Sloan and Apex quarries. Calcining and milling processes. at the Sloan and Henderson plants also are outlined. The Sloan dolomite and limestone quarries and plant are in secs. 12 and 13, T. 23 5., R. 60 E., and sec. 18, T. 23 S., R. 61 E., M.D.B. &M., Clark County, Nev., about. 17 miles by paved highway southwest of Las Vegas (fig. 1). The Apox limestone quarry, and crushing plant are in sec. 26, T. 18 S., R. 63 E., M.D.B.&M., Clark County, Nov., approximately 18 milos northeast of Las Vegas, adjacent to U. S. Highway 91 (fig. 1). The Henderson calcining plant is Inc., in sec. 13, T. 22 S., R. 62 E., 14 miles southeast of Las Vegas on U. in a reduction unit of Basic Magnesium, M.D.B. &M., Clark County, Nev., about S. Highway 93 (fig. 1).

Sep 1, 1949

By Sidney Katell

This cost bibliography, covering the period from January through December 1960, is a continuation of the series which began with the publication of Information Circular 7516 in October 1949. It is also the second report in the series to be prepared as a cooperative effort by the Bureau of Mines and the American Association of Cost Engineers. The cooperative agreement between the two groups provides for the publication of an annual bibliography with the work load involved in the preparation shared equally. The abstracted articles, concerned with all facets of cost engineering in the field of petroleum and chemical plants and related facilities, came from the following sources: 1. Bureau of Mines Information Circulars. 2. Bureau of Mines Report of Investigations. 3. Chemical Engineering. 4. Chemical Engineering Progress. 5. Chemical Week. 6. Coal Age. 7. Coal. Utilization. 8. Cost Engineering. 9. Industrial and Engineering Chemistry. 10. Nucleonics. 11. Oil and Gas Journal. 12. Petroleum Engineering. 13. Petroleum Refiner. 14. World Oil.

Jan 1, 1961

By Lu Li, Sara E. Wilson

Occupational exposure to whole body vibration has long been associated with increased incidence of low back pain and low back injuries1. A number of studies have investigated transmissibility of seat pan vibration 5, 6. While transmissibility has been well researched, the mechanism by which vibration may induce injury has not been thoroughly studied. Winter et al. identified increased reflex response delay after vibration exposure and speculated that muscular fatigue may be the cause of this increase9. However, a mechanism has yet to be demonstrated completely. A potential mechanism that may explain the increased risk is neuromotor habituation. Muscle spindle organs have been shown in the extremities to be sensitive to muscle and tendon vibration. Rapid length changes in muscle have been shown to result in kinesthetic illusions as the regular firing of the muscle spindles is interpreted as muscle lengthening4, 7. These illusions have also been demonstrated in the paraspinal musculature2. With removal of vibration, research in the extremities has demonstrated increased positioning errors, probably due to neuromotor habituation8. In this research, it has been hypothesized that neuromotor habituation after exposure to occupational vibration will increase positioning errors. It is further hypothesized that these errors can be shown to be linked to increased reflex response time. Such increased reflex response time could, in turn, decrease spinal stability and increase low back injury risk. Methods Both positioning error and sudden load response were measured before and after exposure to 20 minutes of 5 Hz, 0.223 m/s2 RMS seat pan vibration. Subjects were asked to sit on an unpadded seat without a backrest. Throughout the whole body vibration period, subjects were instructed to put their hands on a stable hand rest and feet on an adjustable stable footrest. The subjects were instructed to assume a comfortable and relax sitting posture for the duration of the exposure. Positioning error was measured using an active-active reposition sense protocol. Electromagnetic markers (Motionstar, Ascension Tech, Burlington, VT) were used to track trunk motion. With markers attached to the skin at the T10 vertebra, the S1 vertebra and manubrium, trunk flexion (the angle from vertical of the line connecting T10 and S1) and lumbar curvature (the difference in inclination of the T10 and S1 markers) were tracked. In the reposition sense protocol, subjects were asked to maintain an upright trunk flexion and to rotate their pelvis and lumbar curvature to assume a target lumbar curvature. In the protocol subjects completed training trials, where they were asked to match their lumbar curvature using a visual display, and assessment trials, where they were asked to reproduce the lumbar curvature from memory. After two initial training trials, training trials and assessment trials were alternated for a total of 3 assessment trials. Reposition error was defined as the absolute difference between the target lumbar curvature and the lumbar curvature the subject assumed during the assessment trials.

Jan 6, 2006

VOLUME II Volume II, in conjunction with Volume I, is a general guide to the selection of cost-effective methods of site data acquisition in all geologic environmental, and socio-political circumstances. The judgement of a generalist or trained specialist must be relied upon in the final analysis to design the optimum program for a specific site.

Jan 1, 1976

By Richard G. Stearns

Extensive thick lignite apparently lies within 250 feet of the land surface in Dyer, Lake, Lauderdale, Obion and Tipton counties. Information on geology, land use, soils, groundwater and instability is compiled, along with a bibliography. A test and monitoring site was investigated at Fort Pillow Prison in Lauderdale County. Analyses were made of lignite, overburden, associated water and leachate. Lignite has high BTU (about 7800) and low sulfur (1.1% avg.). A year or more of data are presented on rainfall, water levels, and chemistry of surface water, groundwater, leachate and water from test pits. Main potential environmental problems are quality of surface water, and possibly shallow groundwater. The main aquifer of the region will likely be un-affected by mining. Low transmissibility of shallow aquifers will minimize lowering water levels of wells. Soil reclamation and conservation should be readily accomplished, Dangerous earthquakes have a low probability and mines are not significantly more hazardous than steep bluffs.

Jan 1, 1981