Search Documents

By S. Ralph Austin

Emanation coefficients of 950 samples of domestic uranium ore were successfully and rapidly determined with fair precision by modifications of the closed-can, gamma-only assay method, using commercially available or similar equipment. Coefficients range from <1 to 91 percent. Emanation varies considerably within each mine and area, but distinct differences among major mining areas were found, ranging from 7.5 percent for Moss Back Member, Chinle Formation, Southwest Lisbon Valley, Utah, to 56.6 percent for Ft. Union Formation (?), Powder River Basin, Wyoming. Coefficients also vary with (1) uranium mineralogy; (2) radium mineralogy; (3) lithology of host rocks; (4) grain size of uranium and radium minerals; (5) comminution of ore; (6) estimated porosity and permeability; (7) moisture content; (8) ore grade; (9) supposed mobility of deposits; age of deposits is unknown but limited by (10) age of host rocks which shows only doubtful correlation with emanation. Data obtained may be used to evaluate effects of investigated parameters on radon concentration in mines and thus to select efficient control measures. Drill-core emanation data allow estimates of probable radon problems in undeveloped deposits.

Jan 1, 1978

By Forrest T. Moyer

Injury experience in the coal-mining industry was worse in 1965 as both the frequency and severity rates of injuries increased 2 and 6 percent, respectively, over comparable data for 1966 (tables 1-8). The retrogression in the safety record during; 1965 resulted frog the less favorable record at bituminous-coal mines, which more than offset the improved injury experience at anthracite mines. The 259 fatal and 11,138 nonfatal injuries occurred at a rate of 45.77 per million man-hours of exposure and resulted in a severity rate of 8,960 days lost per million man-hours. Although the number of fatalities was the second lowest annual total in the recorded history, it was 17 higher than in 1964. At anthracite operations the total of 6 fatalities in 1965 was the lowest annual figure in statistical history. The annual numbers of nonfatal injuries at ill coal mines and the resulting rates of occurrence have varied little in the past 5 years (table 1). The total days lost from all injuries rose from 2.1.3 million in 19b4 to 2.23 million in 1965 (table 5). Fatal and permanent total injuries, with a standard time charge of 6,000 days each, accounted for 1,650,000 days; Permanent partial injuries, 191,932 clays; and temporary total disabilities, 383,911 days. The severity rate for fatal injuries was 6,241, 8 percent higher than in 1964, and the nonfatal severity rate of 2,718 days lost per million man-hours was 2 percent higher than in the preceding year. The average severity of permanent partial injuries ire; 730, or 48 days fewer per injury than in 1964. The average days lost for each temporary total injury was 36 days in each year.

Jan 1, 1968

By E. D. Calvert

Molybdenum has been successfully cast into static and rotating molds in conventional equipment used for casting titanium and zirconium. Melting was accomplished by using an arc potential of 36 to 40 volts with a current of 10,000 amperes. Pouring efficiency, after a skull had been formed in the crucible, averaged 70 percent. Techniques are described by which four successful castings were made. Tensile properties on specimens cut from one centrifugally cast tube averaged: Tensile strength, 39,800 p.s.i.; yield strength (0.1 pct. offset), 35,300 p.s.i.; elongation, nil; reduction in area, nil; impact strength, 2 ft.-lb.; hardness DPH (diamond pyramid hardness) 180. Mold reaction was not evident in shapes cast in machined graphite. This was not true, however, for rammed graphitic-base molds.

Jan 1, 1960

By Robert L. Lagace

The purpose of the work reported herein was to investigate whether available telephone multiplexing equipment offered a means to rapidly upgrade the traffic-handling capacity of present mine telephone systems and provide for selective calling for safer and more efficient mine operation. Common sense was used to decide whether or not an item could be termed "available." Since conventional telephone gear is not designed to interface pager phones for example, existing shelf items would require adapters to compatibly interface these two types of gear for independent operation over the present single twisted pair used in mines. These and similar small items were allowed, but if a system required any extensive design work to adapt it for the mines, we ruled it "not available."

Jan 1, 1975

By S. J. Davenport

The increased consumption and importation of fluorspar and cryolite (1)3/ in recent years, and especially the addition of fluorine compounds to drinking water in the United States, have aroused renewed interest in the properties of such compounds and possible health hazards incident to their use. It has been suggested that the issuance of a revision and elaboration of Information Circular 7311, The Hazards of Hydrogen Fluoride Poisoning in the Mineral and Allied Industries, which hay been out of print for some time, would be opportune. Fluorine minerals have been known since the Middle Ages. Fluorine was isolated in 1886 by Moisson (2).

Jan 1, 1954

By Christopher Mark, Robert J. Tuchman

This proceedings volume contains papers presented at technology transfer seminars sponsored by the National Institute for Occupational Safety and Health (NIOSH) on New Technology for Ground Control in Retreat Mining. The seminars were conducted at five locations: Uniontown, PA (March 26, 1997), Norton, VA (April 8, 1997), Pikeville, KY (April 10, 1997), Charleston, WV (April 17, 1997), and Evansville, IN (April 22, 1997). The papers presented here describe several new, highly practical technologies developed by the NIOSH Pittsburgh and Spokane Research Centers3 to improve safety during pillar retreat operations. Two central issues are addressed: pillar design and mobile roof supports (MRS&apos;s). Proper pillar sizing is essential for safe pillar extraction. The Analysis of Retreat Mining Pillar Stability (ARMPS) program and its large data base of actual mining case histories are presented. LAMODEL, a second computer program, can be used for analysis of multiple-seam and other complex mining situations. Other papers address pillar design to avoid massive pillar collapses and the proper role of coal strength testing. MRS&apos;s have greatly improved safety where they are used for pillar line support. We studied the application of MRS&apos;s at 20 mines throughout the Eastern United States. Conclusions regarding the most effective section layouts, cut sequences, and support placements are reported. Field and laboratory tests of MRS&apos;s are also described.

Jan 1, 1997

[ ]

Jan 1, 2008

By Milne J. Schmid

A program has been conducted to determine the feasibility of providing a borehole liner for Kelly Bar drilled boreholes in Southern Florida. The concept was to drill the borehole with the Kelly Bar and with it still in the borehole insert a tube which would remain in the unstable ground after withdrawl of the bar. The tube then will provide an unobstructed borehole for the charging of explosives upon completion of the drilling the shot pattern.

Jan 1, 1977

By Motohisa Kanda

The time and amplitude statistics necessary to adequately describe electromagnetic (FM) noise in mines are illustrated through computer software techniques. They are 1) Allan Variance Analyses (AVA), 2) Interpulse Spacing Distributions (ISD), 3) Pulse Duration Distributions (PDD), 4) Average Crossing Rates (ACR), and S) Amplitude Probability Distributions (APD). These statistics are illustrated using data taken from a rather large store of raw analog data recorded in operational mines. The curves generated for the illustrations characterize the noise environment in the mines from which the corresponding data were taken, and should aid in the design of reliable communication systems for such mines.

Jan 1, 1974

By John C. Machisak

The National Safety Competition is sponsored and conducted annually by the Bureau of Mines, U.S. Department of the Interior, to give greater impetus to the building of programs safeguarding the employees of the mineral industries from disabling work injuries. The results of the 1960 National Safety Competition are presented in this publication. Mines and quarries that were awarded the Sentinels of Safety trophy for the best safety record in their competitive group and those mineral operations that ranked second, third, fourth, and fifth in the competition are listed with a summary of their achievements in preventing disabling work injuries. In addition, this publication presents statistical data on disabling work-injury experience in all other mines and quarries participating in the annual competitions.

Jan 1, 1962

By T. Mal

A test system was developed at the National Institute for Occupational Safety and Health&apos;s ventilation test gallery for measuring airflow using a three-axis ultrasonic anemometer. The gallery war used to simulate face airflow conditions in underground mines having a blowing curtain. Airflow data, collected at multiple sampling locations between the face and the end of the curtain, were used to draw airflow profiles for different curtain setback distances, intake flow quantities and entry widths. In addition, methane was released at the face, measured at the sampling locations and displayed as methane distributions in the area between the curtain and the face. Entry geometry had a significant effect on airflow patterns, and the flow patterns affected the distribution of methane in the entry. Flow measured at and parallel to the face was a good predictor of methane dilution and removal within 0.6 m (2ft) of the face.

By R. L. King

This report describes a method for designing and constructing ground beds that has been developed under the sponsorship of the Bureau of Mines. The procedures for designing and constructing a driven-rod ground bed with a resistance of 5 ohms or less are given. Some of the theory of soil resistivity and fall-of-potential resistance measurements is included. Results of a bed constructed at the Bureau of Mines mine car roadway are presented.

Jan 1, 1978

By Ren G. Dong, Richard McCormick, Dan E. Welcome

Vibration exposure at workplaces is generally multi-axial. The health effects of vibration exposure also likely depend on the vibration direction. Therefore, there is a wide interest in the simulation of multi-axial vibration in laboratory experiments. Advances in technology have led to the development of a new 3-D test system for studying hand-transmitted vibration exposure and health effects. The purposes of this paper are to introduce the system and to present the results of its preliminary evaluations. Test System As shown in Figure 1, the system is basically composed of three vibration generators, a multi-axis vibration control system, instrumented handle, handle fixture, and shaker-fixture linkages (stingers). [ ] Figure 2 shows the array of three vibration generators (MB Dynamics, Energizer BLACK-500 lbs) and their associated support bases and foundation developed by MB Dynamics (Cleveland, USA), which create the 3-axis simultaneous motion. These electrodynamic exciters are powered by power amplifiers which provide current proportional to the analog drive signal from a controller. The controller (JAGUAR Multi-Input/Multi-Output closed-loop vibration controller) was provided by Spectral Dynamics, San Jose, California, USA). NIOSH-designed instrumented handle was equipped on the system.

Jan 6, 2006

By R. L. Balmer

This information circular, which describes the methods and costs of sinking a small underground shaft with steel supports at the Keystone mine of American Smelting and Refining Co., near Crested Butte, Colo., is one of a series being prepared by the Bureau of Mines on current shaft-sinking practices in various mining districts of the United States. Preparations for sinking a combined exploration, development, and production shaft from the lowest level of the Keystone mine began early in 1957. This vertical, three-compartment, 6-1/4-by 16-foot rectangular shaft was to be sunk in separate stages or lifts so as to correspond with the progress of an associated lateral exploration and development program. The first section of the shaft was collared and sunk to a depth of 209 feet between September 1957 and April 1958. Because of the depressed base-metal market, the mine was shut down as soon as the initial phase of the exploration and development program had been completed and before any deeper sinking could be attempted.

Jan 1, 1962

By Gerald H. Groenewold

Reclamation of surface-mined landscapes is commonly defined only in terms of biological productivity. Other critical concerns associated with surface mining include the long-term quality of groundwater and stability of the postmining landscape. Meaningful reclamation design must address all these concerns. Reconnaissance of postmining landscapes indicates that three types of instability occur in these settings. These include: area-wide settling, localized collapse, and piping. Area-wide settling is most pronounced during the first year after contouring but appears in precontouring valley areas where frozen materials are contoured with a dozer. Although severe in some settings, development typically ends within one year. Piping appears to be a severe and long-term problem in some settings. Piping usually begins soon after contouring ceases and may continue for several years. In some postmining landscapes, piping has only started to develop after as many as five years of apparent stability. Piping is controlled by a combination of physical and chemical conditions in the spoil. A key factor is the presence of highly dispersive materials in the near surface. The design of a stable postmining landscape requires the integration of severe critical factors. These include: 1) detailed knowledge of the distribution of overburden materials with emphasis upon the delineation of highly sodic sediments; 2) proper equipment selection; and 3) a consideration of climatic factors. For reclamation to be successful, it must consider the entire landscape, not merely the soil zone. Any approach short of this will lead, at best, to temporary solutions.

Jan 1, 1980

By R. H. Jefferson

An electrochemical method to selectively determine sulfur dioxide in the presence of sulfur trioxide was investigated. A hydrophobic gas-permeable membrane separates the gas sample solution from an internal filling solution containing a fixed quantity of chloride ion and a sufficiently large excess of sodium bisulfite so that its concentration may be considered constant. Sulfur dioxide diffuses through the membrane to dissolve in the internal filling solution and liberates an equivalent quantity of hydrogen ions. The electromotive force between a precision-ground, flat-ended pH electrode, which acts as the sensing element, and a chloride sensing electrode, which acts as the reference element, gives a direct measure of S02 in the gas sample solution. Calibration curves in water, tetrachloromercurate (TCM) , and citrate buffer absorption solutions were closely parallel with slopes in their linear segments, ranging from 57 to 52 mv/decade of S02 concentration. The slopes compare reasonably well with the theoretically expected slope of 58 millivolts at 21° C. The water standard curve was linear with respect to the logarithm of S02 concentration from 1 to 1,000 ppm S02; the TCM standard curve was linear from 10 to 2,000 ppm S02; and the citrate standard curve was linear from 30 to 5,000 ppm S02&apos; The high efficiency and nontoxicity of citrate favor it as a substitute for the conventionally used TCM in the absorption solution.

Jan 1, 1976

By Anderson Dana

THIS PAPER describing methods and costs of mining and preparing gravel and sand for market at the Port Jefferson plant of the Seaboard Sand and Gravel Corporation, is one of a series of articles on gravel and sand mining, prepared for and published by the U. S. Bureau of Mines, which is designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs, It is recognized that publication of total costs might in many instances cause embarrassment to individual producers, as well as to the industry as a whole. On the other hand, operating costs are essential to the technical [ ]

Jan 1, 1932

By J. F. Barkley

During the present war emergency, under the urge of the Federal Government to store coal, the following questions are frequently asked by coal users: (a) Will the coal lose any, of its heating value in storage? (b) Will it slack and give a smaller-size coal? (c) Will its burning characteristics change in any way? (d) Will it catch fire from spontaneous combustion? (e) What precautions should be taken when coal is stored? DISCUSSION (a) Loss of Heating Value Studies by the Bureau of Mines show that the loss of heating value of coal in storage commonly has been overestimated. Various types of storage tests were made on New River, Pocahontas, Pittsburgh gas, and Sheridan (Wyo.) coals. The following is quoted from Bureau of Mines Bulletin 136, Deterioration in the Heating Value of Coal During Storage, by H. C. Porter and F. K. Ovitz (p. 8):

Jan 1, 1943

By A. C. Fieldner, G. W. Jones

Tests were made at the Government Fuel Yard , operated at Washington , D. C. by the Bureau of Mines , Department of the Interior , in order to determine and improve the adjustment of the carburetors on the trucks used for transporting coal from the Fuel Yard to the different Government buildings in Washington . The tests were made possible through the hearty cooperation of G , S. Pope , engineer in charge of the Fuel Yard . Joseph Burrows and A. E. Foote of the garage department assisted during all the tests and supplied information on the mileage obtained by the trucks for the months preceding and succeding the time the tests were made . The Mack trucks used range in capacity from 2-1/2 to 7-1/2 ttoonnss .. The majority of the carburetors were Stromberg G- 3 type , as shown in Table 2. During the winter months , when the demand for coal is heavy , from 30 to 35 trucks are used . At the time the tests were made , only about ten of the trucks were in daily use , owing to the small demand for coal during the summer months , and scarcity due to labor conditions . Samples of the exhaust gas were taken on the trucks kept in service for summer hauling in order to determine the carburetor adjustment as used . Changes were then made to a more economical adjustment wherever possible , without sacrificing flexibility of operation and power . In every case the adjustments were maintained for maximum power , but were adjusted to the leanest position to give that power . In all but one case the carburetors were found to be adjusted too rich for maximum power and economy . These results are considered in detail in a later part of this report .

Jun 1, 1923

By Masami Hayashi

The Bureau of Mines estimated the cost for ,3 uranium ion-exchange recovery system using five grades of 17.0, leach solution producing 815,570 pounds of U 0? per year from an ammonium bicarbonate in situ leach solution. The system flowsheet consisted of four unit operations: (1) Multiple-compartment ion-exchange (MCIX) absorption; (2) MCIX elution; (3) precipitation of the uranium as yellow cake, filtering, calcining, and packaging; and (4) waste disposal. The total fixed capital cost of a system treating 2,000 gallons per minute of 0.1-gram-per-liter-U308 leach solution was estimated as $6,888,000. For n basic case of an MCIX system depreciating in 9 years, unit production cost of U308 was $3.51 per pound. A decrease in feed solution grade from 0.[4] to 0.03 gram per liter increased the production cost exponentially. Shorter depreciating periods significantly increased the production cost particularly for the lower grade feed solutions.

Jan 1, 1979