Search Documents

By E. H. Denny

The subject of haulage and heisting hazards is one that merits the attention of everyone engaged in mining. The purpose of this circular is to the importance of such hazards as are shown by Bureau of Mines accident figures, to give some examples of recent accidents and briefly analyze the immediate contributing causes, and to discuss some general means found by metal- and coal-mining companies to minimize those hazards. Haulage and hoisting accidents collectively constitute the second most common cause of accidents in and about coal mines and the third most common cause in and about metal mines. In both these types of mines falls of ground cause more accidents than haulage, and in metal mines falls of persons in raises and similar openings also exceed haulage accidents in number.

Jan 1, 1942

By L. J. Kane

Conventional methods for determining the size of dust suspended in a gas require that agglomerates (clusters of particles) first be broken into particles, but in evaluating industrial dust-removing equipment the size of the agglomerates as they actually exist in the gas stream is far more important. This paper presents results of an investigation by the Federal Bureau of Mines to develop methods for determining the size of dust agglomerates suspended in a gas stream. The studies are part of the Bureau's continuing research on synthetic liquid fuels. The size and size-distribution of agglomerates as they exist when the gas reaches the filter was determined by using a membrane filter in conjunction with a dust count under a microscope. A membrane filter is a cellulosic sheet about 150 microns thick containing millions of holes per square centimeter--holes of uniform diameter that run directly through the sheet without interconnection.

Jan 1, 1960

By Glen C. Reed

"The Avon mica district of Latah County, Idaho, is situated on a heavily forested spur of the Thatuna Range at an average altitude of 4,000 feet. The nearest rail connection is at Avon, a small farming settlement 7 miles to the south. The main supply point is Moscow, Idaho, which is 35 miles by graveled and graded county roads from Avon.Discovery of mica-bearing pegmatites in 1885 was followed in 1888 by exploitation of several outcrop deposits. Although factual data are unavailable, past production appears to have been well in excess of $100,000. Recent production (September 191 to April 1945) amounted to 65,824.78 pounds of trimmed sheet mica and 33,294.17 pounds of punch mica having a total gross value of $434,298.The several properties of the district are variously owned by estates, individuals, and the State. When active, all wore under lease or sublease to individual operators.The deposits are in an area of pre-Cambrian schists adjacent to a small granitic outlier of the Idaho batholith. The pegmatites are nearly concordant in dip and strike to the foliation of the enclosing schists. The more persistent bodies are usually tabular, lenticular, or pegmatite. Individual dikes range in length from 10 feet or less to 300 feet.The recoverable crude mica content of the pegmatites ranges downward from a maximum of 115 pounds per ton of pegmatite mined. Material discarded in rifting and trimming operations further reduces recovery to a maximum of 5 pounds per ton -of pegmatite mined. The average recoverable sheet content of the 'recently operated .deposit is estimated at 2 pounds per ton of pegmatite -mined. Available data indicate that about 21 percent of the district's recent production of trimmed sheet mica has been ""Group A"" material suitable for exacting condenser requirements. A few of the dikes contain local concentrations of beryl.Reserves of the three known major deposits of the district are estimated at about 600 to 1,000 tons of combined ""indicated"" and ""inferred"" crude block mica. One of these deposits is inferred to contain between 150 and 450 tons of beryl.It is believed that those mica reserves are minable only under a cost-market price ratio similar to that established during 1943 and 1944. A small part of the reserves can be ""high-graded"" under the present price structure. Profitable recovery of the beryl would require a market price four to five times that paid in 1944.Preliminary examination of the Avon mica district was made by the Bureau of Mines in the summer and fall of 1942. A study of the Muscovite mine and a brief reconnaissance of the surrounding district led the Bureau to recommend that the district be explored by angle-dozer trenching."

Jul 1, 1946

Relatively few longwall mines in the U.S. operate under multiple seam conditions where the two seams are less than 200 ft apart. This paper describes the experience of six that do. These operations are located in PA, WV and UT, and include examples of both undermining and overmining. Some operate above or beneath their own workings, others are in historic mining districts and must contend with abandoned mines that are decades old. The lessons that these mines have learned cover a broad range of topics, including: • Whether to stack gateroads or place them under old gob areas; • How to size pillars and select artificial support to cross longwall stop lines; • How to use yield pillars to minimize multiple seam stresses and coal bump potential, and; • When to anticipate the creation of pathways for gas, water, or oxygen between current and abandoned gobs.

By David L. Shuck

This report was prepared for the Bureau of Mines to describe the current methods of design, construction, and development of wells for in situ leaching of uranium. The discussion includes the alternatives for well design drilling equipment and fluids, grout formulation and emplacement, well integrity testing and repair, and well development and stimulation. Current practice in these areas was determined through interviews with eight operators of commercial scale in situ facilities and is also discussed. Based on this information plus the authors' experience, recommendations are made regarding well design, construction, and development tor in situ leaching.

Jan 1, 1982

By C. H. Herty

"The work on the physical chemistry of steelmaking, as carried out at the Pittsburgh Experiment Station of the United States Bureau of Mines in cooperation with Carnegie Institute of Technology and, the Metallurgical Advisory Board, has covered a series of fundamental studies on the action of oxygen in liquid steel and the application of the findings to open-hearth operation. The staff has varied from 14 to 23 men per year, some of whom have been Bureau of Mines physical chemists and metallurgists, others research engineers of the Metallurgical Advisory Board, and the remainder graduate students employed as research fellows at the Carnegie Institute of Technology. The work on the laboratory studies, and particularly on slag systems, has been in charge of G. R. Fitterer, associate metallurgist, Bureau of Mines, while the plant work has been under the direction of C. F. Christopher, research engineer of the Metallurgical Advisory Board. In all, some 16 physical chemists and metallurgists and 24 research fellows have taken part in the experimental work. Advantage has been taken of the opportunity for cooperation with the University of Pittsburg to have certain phases of this program made the subject of graduate work, particularly the laboratory studies on the deoxidation of steel with manganese-silicon alloys.The general method of studying oxygen has been, first, to determine the solubility of the various oxides in liquid steel. To date the solubility of Fe0 in steel has been determined, over a wide temperature range.3 The straight-line relationship in the plot of solubility versus temperature indicated that under a slag of 100 per cent Fe0 the oxygen was present in the steel as dissolved FeO. A further conclusion drawn from this work was that the solubility of FeO in the metal was proportional at a given temperature to the mol fraction of Fe0 in the slag if the slag contained a large excess of basic constituents. This result was determined from a study of the solubility of Fe0 under slags containing lime and iron oxide in various proportions. These data have been used extensively in determining the saturation of a bath of open-hearth steel under any conditions of slag composition, and results to be given later showed that the solubility curves are consistent with the results obtained in practice."

Dec 1, 1930

By P. D. Laverty

This report describes a processing method developed by the U.S. Bureau of Mines to produce high-quality flake graphite from the steelmaking waste known as kish. The kish produced by current steelmaking practices is a mixture of graphite, desulfurization slag, and iron that is skimmed from the molten iron feed to the basic oxygen furnace. It is estimated that the graphite content of kish discarded by U.S. steel plants is more than sufficient to meet the total U.S. demand for flake graphite. That need is now filled by natural graphite from foreign sources. Kish was treated by a combination of screening and hydraulic classification to produce a concentrate containing greater than 70 pct graphite. Leaching of the concentrate with hydrochloric acid solution gave a graphite product with 95-pct purity. An optional secondary leaching operation with hydrofluoric acid produced graphite with a purity of 98 pet or greater. The flake size of graphite from kish ranged from 10 mesh down. Evaluation of test samples by industrial graphite users indicated that kish graphite is a suitable substitute for the natural material for most uses. A process flowsheet and material balance for pilot plant design are presented.

Jan 1, 2010

By Michael J. Beus

This Bureau of Mines report describes a tunnel stress relaxation gage (TSR) developed to measure initial radial displacement around full-sized underground openings. The TSR technique was shown to be a valid concept in previous field verification tests. Sensitivity has been improved by employing a titanium alloy cantilever in the transducer head, which also permits a deeper sensor location. Use of improved fabrication methods such as stainless steel bellows and sputtering techniques and use of an environmental chamber for testing greatly increased overall reliability. A miniature data acquisition system (DAS) was interfaced directly to the transducer for increased versatility and containment entirely within a borehole. The present TSR system is suitable for use around full-size underground excavations, particularly machine-bored openings. Field evaluation of the improved instrumentation verified the design goals.

Jan 1, 1978

By Thomas J. Witzig

This Bureau of Mines report is a background study of the International Tin Agreement. Attempts at stabilizing the tin market prior to the agreement are detailed, as well as the conditions and negotiations that set up the agreement. Details of the five consecutive 5-year agreements beginning in 1956 are presented, with emphasis on membership and the agreements' primary tools: the buffer stock and export controls, Attention is focused throughout on the United States activities during the period, especially with regard to its strategic stockpile, and its involvement with the agreement culminating in its membership, for the first time, in the fifth agreement beginning in 1976. Considerations leading to the U.S. decision to join are detailed, and U.S. activities in the negotiations for the sixth agreement are presented. The status and outlook for the agreement are discussed, and evaluations of the effectiveness of the agreement and its components are reviewed.

Jan 1, 1981

By G. R. Smith

This report describes research carried out by the Bureau of Mines to develop new technology for electrorefining metals at much higher current densities than those normally used in commercial practice, preliminary studies using rotating-ring and cylinder electrodes to increase the mass transport of copper are discussed. Following this work, single- and multichannel cells were developed that utilized a high electrolyte flow in the channels formed by the anode-cathode pairs. Using these cells, copper was successfully refined at current densities in the range of 70 to 300 amp/ft2. The effects of flow rate, electrolyte composition, and grain-refining and leveling agents on the morphology and purity of electrodeposited copper were determined.

Jan 1, 1979

By G. J. Colaizzi

The Bureau of Mines, at the request of local authorities in Rock Springs, Wyo., investigated and conducted through contracts a multistage program of exploratory drilling and pumped-slurry backfilling of 15 areas of potential subsidence in abandoned mine workings underneath that community. Initially, the Bureau in 1969 had recommended a program of gravity blind flushing of some of the inaccessible mine voids, and in 1970 a new technique, the pumped-slurry injection process, was tested for the first time in a site adjacent to the city's area of severe surface subsidence. Success of this initial testing program, and of a large-scale project in Scranton, Pa., led to further large- scale projects, funded by Congress, that resulted in the successful back- filling not only of all 15 target areas of potential subsidence in Rock Springs, but also of several areas in other States. Total cost of the projects in Rock Springs, including the original pumped-slurry test, was $3,243,993. A total of about 923,000 tons of sand was injected hydraulically into mine voids, rendering 178 acres of residential and central-downtown areas of Rock Springs less susceptible to subsidence damage. The pumped-slurry method was proved to be much superior to the gravity blind flushing method in term of the amount of solids that could be injected underground through a single borehole. However, there are special conditions that make this technique more or less applicable in different areas or underground configurations, as noted in the report's conclusions.

Jan 1, 1980

By Meherwan C. Irani

The Bureau of Mines is developing a new technological approach to handling the problems of fires in abandoned coal mines and waste banks. This new technology involves the accelerated combustion of "waste" coals in place (i.e., in situ) under controlled exhaust ventilation conditions, which allows for total management of the combustion products; including utilization of the heat produced" This new concept could significantly lower the costs of reducing the environmental and public safety hazards associated with waste coal fires, and could lead to the conversion of a coal waste to a coal resource. The controlled burnout technology has progressed from the laboratory stage to a full-scale field evaluation stage at the site of an abandoned-coal-mine fire. This first report describes the site selection, evaluation, and preparation, and the design and construction of the full-scale controlled burnout installation. Subsequent reports will deal with the results of the operational field trial.

Jan 1, 1983

The following Inventory was prepared to provide mineral deposit data to the U.S. Army Corps of Engineers for use in the Resource Development Navigation Study in Alaska. The inventory was prepared using data contained in the U.S. Bureau of Mines Minerals Availability System (MAS) database. The Alaska portion of the database contains Information on over 7,000 mineral locations and deposits throughout the state. When MAS was established In 1975, database entries were originally compiled from literature searches by both Bureau personnel and contractors. Deposit data are obtained/maintained through Information gained from a variety of sources, Including published and unpublished Bureau of Mines reports, records, and files; U.S. Geological Survey (USGS) Bulletins, Professional Papers, and other reports; technical and professional Journals; State and other Federal agency publications; data generated during field examinations; and information obtained from knowledgeable individuals. Because of the size of the data base, many of the data have not been significantly modified since initial entry. Each deposit on the MAS data base has a sequence number of the following form:

Jan 1, 2011

By D. Randolph Berry

The United States Bureau of Mines (USBM) awarded a contract to Foster-Miller, Inc. to develop guidelines for the storage and use of Self-Contained Self-Rescuers (SCSRs) in underground non-coal mines. An SCSR is a device capable of supplying, in an emergency, one hour of self-contained oxygen (no breathing of mine air). The information and recommendations in this report were developed primarily from three sources: discussions with mine representatives (including management, labor, and government), site visits in underground mines I and a detailed analysis of every reported non-coal accident which produced d hazardous atmosphere during the 5-year period 1976-1980 -plus ten other major incidents from prior years. Volume IV has three major sections: Recommendations and Discussion (Section 2), Analysis of Mine Accidents (Appendix A), and a Summary of Discussions with Mine Representatives (Appendix B).

Jan 1, 1983

By Eric S. Weiss, Deno M. Pappas, Timothy M. Barton

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) has been evaluating developments in sealant support systems from a ground control perspective. The proper selection and use of a sealant material can significantly enhance ground control which may result in a decrease in worker related injuries due to ground falls. The purpose of this paper is threefold: to briefly review the current state-of-the-art technology in shotcrete and membrane developments, to evaluate the preliminary findings of a long-term underground study of various types of sealant materials, and to examine installation practices that are critical for an effective sealant material. The underground study utilizes NIOSH’s Lake Lynn Laboratory Experimental Mine to evaluate the long-term performance of several types of shotcrete and membrane materials. Sealant performance to date have been evaluated on a regular basis over a two year period. Although the study is still ongoing, critical mining practices were identified that may seriously effect the bond of the sealant materials to the mine roof and rib; most notably, the importance of scaling and thorough cleaning of the rib prior to application. Also, results froman extensive series of Schmidt Hammer tests found that the shotcrete increased in strength by 70% during the humid summer months.

By James D. Noll, Jon A. Hummer, Shawn E. Vanderslice, Aleksandar D. Bugarski, George H. Jr. Schnakenberg, Steven E. Mischler, Larry D. Patts

The National Institute for Occupational Safety and Health designed and conducted a study in an underground metal mine to assess the effects of selected diesel emissions control technologies on the concentrations of diesel particulate matter and gases in underground mine air. The control technologies studied included diesel particulate filter (DPF) systems, filtration system with disposable filter elements, diesel oxidation catalytic converter, and biodiesel blends. Each technology was tested on a mining vehicle operated in an isolated area of an underground mine supplied with fresh air. These isolated zone tests allowed for the operation of vehicles under conditions and over duty cycles that closely mimic actual duty cycles of production equipment. The DPF systems reduced the elemental carbon (EC) concentrations in mine air between 88% and 99%. The same systems reduced total particulate matter (TPM) concentrations in mine air by approximately 75%. The biodiesel blends B20 and B50 caused a reduction in the EC concentrations of 26% and 48%, respectively. Those blends also reduced TPM concentrations by 9% and 24%, respectively. The use of #1 diesel fuel reduced EC concentration by 13% compared to #2 diesel fuel. An increase in nitrogen dioxide concentration of up to two times was seen when platinum-catalyzed DPF systems were tested.

Jan 5, 2006

By Forrest T. Moyer

INJURY experience and employment data are presented in this chapter for metal and nonmetal mines, stone quarries, sand and gravel pits, iron blast-furnace slag plants, and metallurgical plants (including ore-dressing and nonferrous reduction plants and refineries) in the United States. Employment and injury experience data for all mineral industries are given in volume II. The 1962 figures are preliminary summations which are subject to revision. They were compiled from all reports from producers received by the Bureau of Mines through April 15, 1963. The data for metal, nonmetal (except well and brine operations), stone, and sand and gravel operations were collected by a mandatory reporting system under the provisions of the act of September 26, 1961, Public Law 87-300 (75 Stat. 649). The act authorized the Secretary of the Interior to study the various aspects of safety in metal and nonmetal mines (excluding coal mines) and report the findings 2 years sub-sequent to the enactment of the law. Data on nonmetal well and brine plants and nonferrous reduction plants and refineries were reported voluntarily by the operators. METAL MINES Preliminary data for the metal mining industry comprise reports on 1,871 mines and pits. The combined fatal and nonfatal injury-frequency rate was 31.95 per million manhours in 1962, a decrease of 8 percent from the similar rate of 34.54 in 1961. Metal operations reported a total of 61 fatal and 3,201 nonfatal injuries.

Jan 1, 1963

By E. G. Davis

The Bureau of Mines investigated gaseous direct reduction of low-grade iron ore concentrates in a continuous fluid-bed reactor. These studies were made in a 4-inch diameter fluid-bed reactor using hydrogen alone, and oxygen-or air-reformed natural gas as the reductants. The percent reduction is directly dependent on the mole ratio of hydrogen in the reducing gas to the oxygen associated with the iron oxide in the ore. Two-and three-stage fluid bed tests were simulated by repeated continuous tests. The results showed that percent reduction of the final product was dependent on the mole ratio of the quantity of hydrogen in the gas of each stage to oxygen in the iron oxide of the initial ore feed. Reduction as high as 87 percent in the single stages and as high as 94 percent in the multistages was obtained when either hydrogen or reformed natural gas was used as the reducing gas. Magnetic separation and concentration of the highly reduced fluid-bed product yielded a high metallic iron concentrate analyzing 85 percent total iron and 80 percent metallic iron with total iron recovery as great as 90 percent. Agglomeration of the high-grade metallized concentrate produced hard pellets analyzing 85 percent total iron and 78 percent metallic iron. Green pellets, with good strength, were made without any binder in a drum pelletizer. Direct melting of the high-metallic fluid-bed product in a basic lined arc furnace produced a nearly pure iron which contained 0.09 C and 0.01 P with 95 percent recovery of the metallic iron in the metal.

Jan 1, 1972

By Joseph M. Kuchta

The limits of flammability and minimum autoignition temperature of a fuel are important elements in assessing fire and explosion hazards that may exist when using or handling the fuel. The limits of flammability define the range of compositions of the fuel gas or vapor mixed with an oxidant through which a flame, initiated by an outside energy source such as an electrical spark, can propagate. The minimum autoignition temperature (M.A.I.T.) is the lowest temperature at which the fuel vapors ignite spontaneously in a specified medium; in this case the ignition energy is supplied by the heat content of tae environment. This temperature is also referred to as S.I.T. value by some authors. Because the autoignition of a fuel also depends on the time interval during which the fuel is subjected to heat, ignition delays are significant. Ignition delay is defined here as the total time elapsed between the introduction of the liquid fuel into the oxidizing atmosphere and the appearance of a flame. This time interval includes both the physical and chemical processes leading to ignition. The ignition delay is usually maximum at the M.A.I.T, and decreases as the temperature of the system is increased. The flash point and the fire point are also useful in assessing the fire and explosion hazards of a fuel. The flash point is the lowest temperature at which saturated, flammable fuel vapor-air mixtures are formed at atmospheric pressure and, therefore, it is essentially the lower limit of flammability

Jan 1, 1962

By E. Divers

This Bureau of Mines report presents results of an underground evaluation to determine the respirable dust and gas control effectiveness of a combined (push-pull) face ventilation system for coal mines. The system utilizes both blowing and exhaust curtain, continuous miners equipped with radio remote control, and flight conveyors. Bureau of Mines tests showed a 97% reduction in respirable dust concentrations from the usual cab position on the continuous miner to the remote control operator's position. This allowed the remote control operator to be well within, and the usual cab position to exceed, Federal respirable dust standards. Tests utilizing a safe tracer gas, sulfur hexafluoride (SF6), to determine the face ventilation effectiveness of the combined blowing and exhaust system showed that the system also has excellent methane dispersion capability. Where wide entries permit, this combined face ventilation system and use of remote control can be a very effective method for dust and gas control.

Jan 1, 1982