Search Documents

By D. Gearhart

Full-scale tests are conducted on mine roof supports using protocols developed by the National Institute for Occupational Safety and Health (NIOSH) using the unique capabilities of the Mine Roof Simulator (MRS). These protocols simulate the loading conditions that the support will be exposed to in an underground mine to determine the performance capabilities and limitations of the support. Some tests are conducted with rigid boundary conditions, creating uniform contact and near ideal axial loading conditions. These tests are used to determine the ultimate performance potential of a support, including the strength, stiffness, and stability. For prop supports where stability is a critical design issue, tests are implemented to induce buckling by a modified end condition, eccentric contact, or biaxial loading. It is important to determine the cpacity of the support design when the support is subjected to unpredictable loading conditions. This paper examines the effect of end conditions and load profiles on prop support performance and applies a new analysis methodology based on eccentric loading to determine a factor of safety for load capacity. Recommendations for installation practices that minimize eccentricity and therefore preserve capacity are also provided.

By H. S. Auvil

[Coals of low-volatile rank cannot be coked without admixing large proportions of high-volatile coal in the usual type of byproduct-coke oven, because they expand excessively and exert side thrust, which ruins the oven walls. Some medium-volatile coals also give trouble. Since high-rank coals produce a strong, blocky coke, it is desirable to have the rank as high as practicable, particularly in the manufacture of foundry coke. Accordingly, it has become the practice to mix or blend high-volatile shrinking, coals with as much low-volatile coal as possible and still have a mixture that will not deform the walls or cause difficulty in pushing the coke. Occasionally, the safe limit of low-volatile coal has been exceeded and ovens have been damaged. It is desirable, therefore, to rave a reliable method of determining the expanding tendencies of mixtures before they are charged into the ovens. Furthermore, coal charges somewhat in its properties as mining progresses, and therefore, mixtures found to be safe at one time may cease to be so subsequently, particularly if nearly the maximum allowable percentage of low-volatile coal is being used.]

Jan 1, 1938

This publication is the fourth in a series of miners? circulars covering various phases of accident prevention in bituminous-coal mines; these circulars constitute a text hook for courses of instruction on accident prevention in bituminous-coal minim. To these may be added material of particular interest in the field where the course is presented. Other circulars in the series are: Accident Statistics as an Aid to Prevention of Accidents in Bituminous-Coal Mines (Miners? Circular 47). Accidents from Falls of Roof and Coal in Bituminous-Coal Mines (Miners' Circular 48). Accidents from Hoisting and Haulage in Bituminous-Coal Mines (Miners' Circular 49).

Jan 1, 1946

By H. E. Powell

Basic data were recorded on the decompositions that take place during thermal decomposition of siderite (FeC03). Both the naturally occurring and a synthetically prepared mineral were studied by differential thermal, thermo-gravimetric, X-ray-diffraction, and chemical (including gas) analyses. Thermal decomposition was studied in the media of dry air, moist air, dry carbon dioxide, dry helium, and dry carbon monoxide and at atmospheric and at reduced pressures. Results showed the thermal decomposition of FeC03 to be an extremely complex process, dependent on environmental factors and side reactions that cannot now be completely controlled. Therefore, full understanding of the reaction involved must depend on additional research with advanced evaluation techniques.

Jan 1, 1965

By Robert V. Berryhill

Reconnaissance studies of beach deposits along approximately 220 miles of the shoreline of Bristol Bay, Alaska, were made to determine if more detailed investigations were warranted. In addition to preliminary mapping of the deposits, samples were obtained from auger borings spaced at 1-mile intervals in key areas; shovel samples were collected to supplement the borings. Most samples were roughly concentrated in the field; magnetic separation tests, petrographic analyses, and determinations for radiometric equivalent uranium, gold, platinum, iron, and titanium were made in the Bureau of Mines laboratory at Juneau, Alaska. Spot samples from some beaches along the shores of the Alaska Peninsula indicate small deposits containing up to 10 percent recoverable titaniferous magnetite; some larger deposits were indicated to contain from 1 to 2 percent total heavy metal, principally as titaniferous magnetite. Significant amounts of other commercial minerals were not detected.

Jan 1, 1963

By Kihong Park, Matthews C. Habjan, Arthur L. Miller

New Mining Safety and Health Administration (MSHA) regulations limit the mass concentration of airborne diesel particulate matter (DPM) or, more specifically, the concentration of elemental carbon (EC), in underground mines. The mine operators are responding by introducing a variety of controls to reduce DPM in the mines, potentially including the evaluation of new maintenance procedures to reduce underground mine vehicle emissions. There is currently a lack of an inexpensive and dependable method to directly measure the DPM concentration emitted from the vehicle tailpipe. To that end, this work demonstrated a simple field portable method for estimating the mass concentration of elemental carbon exiting the tailpipe of a diesel engine using a direct reading photometer. Simultaneous measurements of tailpipe exhaust were made with a Thermo Electron Personal DataRAM 1200 photometer (particulate mass concentration based on light scattering) and by analyzing PM2.5 and PM1.0 samples collected on quartz fiber filters using the National Institute of Occupational Safety and Health (NIOSH) method 5040 (mass concentration of EC via thermal-optical method). Results indicate surprisingly good correlation (R2 ) 0.97) of the two methods when the data are adjusted for relative humidity (RH) and corrected using an empirically generated calibration factor. Although preliminary, it may be possible to implement this method in maintenance shops to monitor emission trends and to compare emissions of various vehicles in a fleet. Such data will be useful for fleet planning to meet new air quality standards.

By A. Baldwin

This report describes the engineering feasibility and economic advantages of a unique new mining machine using cutting bits that take a constant-depth linear cut in the coal face. The studies show that this innovative new cutting concept, being developed by the Bureau of Mines, can be designed into the basic continuous mining machine. The resulting miner would be attractive to mine owners because coal could be mined with minimum generation of airborne respirable dust, substantial increases in productivity, and elimination of methane ignition due to cutting.

Jan 1, 1977

By K. Thirumalai

This study forms a part of Bureau of Mines continuing research on thermal fragmentation of rocks. The potential of internal heating techniques for rock fragmentation is discussed. A concept of rock fragmentation with rapid inter¬nal heating of a localized inner volume of rock is advanced The energy required for rock fragmentation is made available by creating a required vol¬ume of localized heating. The fragmentation of rock using the proposed method is analyzed and qualitatively compared with the results of experiments with Charcoal granite, Dresser basalt, and Sioux Quartzite. High frequency dielec¬tric heating below 100 MHz is used in the study as an example to examine the working of the concept. The selection of operating conditions for the experi¬mental heating is explained. Fragmentation of Charcoal granite and Dresser basalt test rock blocks is achieved for localized heating below 550° C. The heated volume required for fragmentation is observed to be less than 2 percent of the test block volume and the electrical energy consumption is in the order of 3.5 to 6 5 kwhr/m3 The method offers a possibility for in situ fragmenta¬tion of rocks, favorable for internal heating. The method is highly dependent on rock properties governing internal heat generation The efficiency of dielectric heating in the experimental study is observed to increase with increasing dielectric loss of the rock material, ranging from about 10 percent in Sioux. Quartzite to about 50 percent in Dresses basalt

Jan 1, 1970

By Oliver Bowles

"INTRODUCTION Slate has earned a high reputation as a roofing material, carefully selected and properly placed it is rainproof, attractive, and extraordinarily durable. Despite there qualities in its favor, the slate industry during the past 30 years has suffered marked reduction in volume of sales. An increase in building construction and general improvement in business will doubtless bring renewed activity, but considerable ground has to be recovered before the industry can become prosperous. Influences tending to dwarf this long-established industry producing materials of world-wide reputation are analyzed briefly in the following pages in the hope that they may be rectified.HISTORY OF SLATE PRODUCTIONFigure 1 shows graphically the rise and fall from year to year of sales of roofing slate since 1885. In quantity, the peak was reached in 1902, and the most serious decline was from 1912 to 1918, sales at the end of this 6-year period being only one third those at the beginning. Unlike most building materials, slate experienced only a slight recovery in volume of sales during the post-war period, 1920-29. The value closely parallels the volume up to the World War period. Subsequently, however, as unit values increased the aggregate value rose sharololy above the volume curve, attaining in 1928 the point reached in 1903, although the Lumber of squares sold was scarcely one third as great. The increased unit value was due partly to larger sales of heavy architectural grades."

Nov 1, 1933

By Gordon R. Sima

This contract is concerned with the construction of a Time Resolved Audio Dosimeter System consisting of one readout unit and several dosimeter units. The Time Resolved Audio Dosimeter System was designed and developed by the Bureau of Mines with the purpose of this contract aimed at obtaining additional units for further field testing and evaluation. All construction was in accordance with the Bureau of Mines design and/or Bureau approved drawings produced during the course of this contract. This report contains a summary of the construction efforts, problems encountered, recommendations and all drawings produced under this contract.

Jan 1, 1977

By D. R. Tesarik

To ensure the stability ofa tailings pond embankment, the height of the phreatic surface must be kept at or below a safe level. In this investigation, the Bureau of Mines analyzed various horizontal drain designs for tailings embankments to determine their effects on location of the phreatic surface. This report describes the investigation, and it includes 21 dimensionless graphs that can be used to estimate the drain spacing and length dimensions necessary to ensure the stability of embankments of various configurations. Analyses were based on the use of two computer codes, a three-dimensional finite-element code and a two-dimensional finite-difference code. The computer-generated results were compared with results obtained from a laboratory embankment model, other laboratory test results, and piezomet-ric data from two actual tailings embankments. Nearly the same phreatic surface locations were predicted using either of the computer codes. For one of the actual embankments studied, the predicted phreatic surface location was slightly higher than the measured location; for the other, the predicted location closely followed the actual surface trend. Phreatic surfaces of the laboratory model were slightly higher than the code-gener-ated locations, and the differences grew larger as drain length increased or drain spacing decreased.

Jan 1, 1984

By Harry E. Tuff

"This paper is based data obtained by the Bureau of Mines from some of the principal mine operators in Pennsylvania, in the course of a study conducted in cooperation with the U. S. Forest Service, with regard to economies that might be effected in the selection storage, and preparations of timber particularly treatment with preservative to prolong its life.The Pennsylvania anthracite region, considered as a single mining district is by far the largest user of mine timber of any mining district, either coal or metal, in the United States, and the bituminous districts of Pennsylvania rank second. The present annual consumption of mine timber by the coal-mining industry of Pennsylvania probably exceeds 100,000,000 cubic feet annually.In 1919, Pennsylvania produced, in round figures, 145,300,000 tons of bituminous coal, 86,200,000 tons of anthracite, and 5,400,000 tons of iron ores. If it be assumed that the bituminous coal mines required 0.33 cubic feet, anthracite mines 0.7, and iron mines 0.9 cubic feet per ton mined the timber requirements were bituminous. 47,950,000; anthracite, 60,340,000; iron mines, 4,860,000 or a total of over 113,000,000 cubic feet.The average cost of round mine timber in the anthracite region in 1905, was, according to the U. S. Forest Service, 6.6 cents per cubic foot, and $15.00 per 1000 board feet for sawed timber. The present cost Las advanced to 27.5 cents per cubic foot for round timber, delivered to the mine, of which cost 57.4, represents freight charges."

Nov 1, 1923

By H. B. Humphrey, F. E. Cash

The Southern Appalachian coal field extends southward across Tennessee in a belt about 50 miles wide between the eastern and middle sections of the State. The earliest record of the production of coal in Tennessee is for 1840, and the first inspection laws were passed in 1881. In 1887, a second act of the legislature created the office of Chief Inspector, but little was done until 1891 when a new act was passed giving to the Department of Mines added duties and powers. Since that time, except for the years 1915 to 1918, com¬ prehensive annual reports have been published. Data for the tables given in this paper are taken from these annual reports, from those of the Southern Appalachian Coal Operators' Association, and from the publications of the United States Bureau of Mines, which has main¬ tained a station at Jellico, Tenn., since 1911. Complete figures for 1930 are not available yet and they are not included in the averages. The State Department of Mines, the operating companies, and the United States Bureau of Mines cooperate in accident-prevention work. It is the purpose of this report to present in uniform tables the available statistics in regard to fatal accidents in Tennessee and in the coal mines of the United States, in order that the progress in mine safety in Tennessee may be compared with that of the country as a whole, and the present period may be compared with various periods of the past, to indicate the main points of attack in the reduction of accidents.

Sep 1, 1931

By J. D. Davis

THE CARBONIZING properties of Chilton-bed coal from Lorado No. 5 mine, HE Logan County, W. Va., were determined by Bureau of Mines-American Gas Association tests at 600°, 700°, 800°, 900°, and 1,000° C. and by expansion tests. Chemical analyses, agglutinating and plasticity tests, and low- and high-temperature assays also were included in the investigation. Blends with low-volatile Pocahontas No. 3 coal were carbonized at. 900° C. The Chilton coal bed lies in the Kanawha, or Upper Pottsville formation of the Pennsylvanian system; the estimated original reserves are nearly 3.2 billion tons. The bed was 39/1 to 57 inches thick in the Lorado No. 5 mine, and the coal was 38 to 57 inches thick. The carbonization sample contained 62.6 percent fixed carbon on the dry, mineral-matter-free, basis, and the heating value on the moist, mineral-matter-free basis was 15,190 B. t. u. per pound; it therefore ranks as high-volatile A bituminous. It contained 1.8 percent moisture, 35.2 percent volatile matter, 57.9 percent fixed carbon, 5.1 percent ash, and 0.7 percent sulfur, as carbonized. The sulfur was largely organic, and the ash softened at 2,630° F. The agglutinating value determined on a silicon carbide-coal mixture of 15:1 was 6.8. In the Gieseler test the coal softened at 327° C., fused at 407° C., attained a maximum fluidity of 5,730 dial divisions per minute at 435° C., and solidified at 487° C. Maximum resistance in the Davis plastometer was 45.5 pound-inches.

Jan 1, 1951

By Doris M. Hyde

There were no significant changes in the mineral industries of the smaller Caribbean Islands during 1980. Imported petroleum requirements continued to erode economic gains that may have occurred in other sectors. Some relief may be forthcoming as more qualified Caribbean countries take advantage of Trinidad and Tobago's petroleum product financing program (see Trinidad and Tobago). There were no crude oil discoveries in these areas during 1980, although some geophysical testing around the British Virgin Islands and Antigua war underway. In March 1980, the Government of Antigua sold a 75% interest in the 16,000-barrel- per-day West Indies Oil Co. refinery to the Swiss Intermaritime Bank and Intermaritime Management Services for $6 million. The new refinery company is called the National Petroleum Co. Shutdown since 1976, it was originally planned for the refinery to reopen in 1980, but refurbishing has proved to be more extensive than anticipated. The reopening is now expected in 1981.

Jan 1, 1982

By Khamis Y. Haramy

This Bureau of Mines paper describes the use of the borehole shear tester (BST) In mines. Assembly and procedure sections explain how the equipment is assembled and used properly. Schematics of the BST, limitations, test hole specifications, data recording and calculations are all explained briefly, and an example of the data collecting and calculations is given to assist understanding.

Jan 1, 1981

By Henry P. Chandler

[Diamond, because of its extreme hardness and abrasion resistance, has an important function in precision engineering and automation. With the increasing; requirements of modern production for fine tolerances, interchange-ability, and speed, it has become even more important. In spite of the supply of other abrasive and hard materials and of ultrasonic, electrospark rued other substitute grinding, methods, world industry seams likely to absorb large quantities of diamond for industrial purposes. An increasing part of the world's needs will be supplied by manufactured diamond, which was introduced commercially by General Electric Co. in 1957. Use of diamond for glass cutting roes bark several centuries, mid diamond drilling of rock became important to the mining industry M the 1870's. Today, diamond drilling is the most extensively used method of exploring the world's ore reserves; diamond drills two also used to determined the nature of bedrock below the foundations of buildings, dams, and bridges. Diamond drill bits are now used extensively in the petroleum industry, and replacement or steel rock bits with diamond drill bits in hard rock formations has affected substantial savings.]

Jan 1, 1964

By Henry P. Chandler

[Diamond, because of its extreme hardness and abrasion resistance, has an important function in precision engineering and automation. With the increasing; requirements of modern production for fine tolerances, interchangeability, and speed, it has become even hors, important in spite of the supply of other abrasive and hard materials and of ultrasonic, electrospspark rued other substitute grinding methods world industry seems likely to absorb large quantities of diamond for industrial purposes. An increasing part of the world's needs will be supplied by manufactured diamond, which was introduced commercially by General Electric Co. in 1957. Use of diamond for glass cutting goes bark several centuries, mid diamond drilling of rock became important to the mining industry M the 1870's. Today, diamond drilling is the most extensively used method of exploring the world's ore reserves; diamond drills two also used to determine the nature of bedrock below the foundations of buildings, dams, and bridges. Diamond drill bits are now used extensively in the petroleum industry, and replacement or steel rock bits with diamond drill bits in hard rock formations has effected substantial savings.]

Jan 1, 1964

By T. M. Ruff

A prototype mucking machine designed to operate in narrow-vein stopes was developed by Foster-Miller, Inc., Waltham, MA, under contract with the U.S. Bureau of Mines. The machine, called a compact loader-trammer, or minimucker, was designed to replace slusher muckers in narrow-vein underground mines. The minimucker is a six-wheel-drive, skid-steered, load-haul-dump (LHD) machine that loads muck at the front with a novel slide-bucket system and ejects it out the rear so that the machine does not have to be turned around. To correct deficiencies of the tether-remote-control system, a computer-based, radio-remote-control system was retrofitted to the minimucker. Initial tests indicated a need to assist the operator in guiding the machine in narrow stopes. An automatic guidance system that used ultrasonic ranging sensors and a wall-following algorithm was installed. Additional tests in a simulated test stope showed that these changes improved the operation of the minimucker. The design and functions of the minimucker and its computer-based, remote-control system are reviewed, and an ultrasonic-sensor-based guidance system is described.

Jan 1, 2010

By L. D. Tracy

For many yeirs natural gas has been the principal fuel used in the he·1 ting furnaces in those mills located in the. Pi t-c;s. b.urgh district· \7hich manufacture bolts ., nuts, rivets, pick$, mattocks and srr.&11 for6ine;s. For a nUI.1"'.::>er of years the steady supply of this fuel has been more or less interrupted owing to the increased4and f·or d9mes tic use and to the increasing difficulty in securing an ad.eq_ua te c.1mount of natural gas. This condition has led a number of the steel compa.nies to substitute -oulvsrized coal a.s a fuel for the.furnaces. Elaborate irista.llations have been made for pulverizing tne coal ar!d _ coriveyi16 i -c to the fur:waces. • Soon after the furnaces ·-:commenced .. to operate ·,Vi th :pulverized coal, large quanti ties O::f.' fine dust beg.::in to accumulate on the platforms over the fu:rna. ces, the. roof trusses, on the outside of the va.rious· pip·e ·line electric cables a.i.1.d even on the roofs of the buildings. Some of tha comi:,a.n:;.0s, becomin·g alarmed, requested the Bureau of ;Unes to rr.c1ke an investigation to ascertcliin the.· licibili ty of this dust to cause an explosion.· Nhi le conducting this inves ti ga ti on,· an explosion· occurr-2! d in a.nothe:2 nill ·,7hich caused he death of one man and severely burned t;io others. Eleven sc1nrcles of the dust (which for convenience has been termed "mill d.ust 11 ) from various locations in the different mill' buildings were taken and submitted to chemical analyses, microscopic examination and also to flame and explosion tests. From the chu,1ica.l analyses it was found that· the volatile matter in th..:: dusts xanged -from 6.3 per cent to 23,54 per cent, fixed carbon from 50.88 per cent to 67.08 per cent and ash from 32.29 per cent to 32.16 per centw

Dec 1, 1919