Search Documents

By Richard A. Allwes

This Bureau of Mines report presents a procedure for the design of an arch canopy for use in rehabilitating a high-roof-fall area. Only dy-namic line loading of an unbackfilled arch canopy at its crown is considered, and the procedure does not account for an asymmetrical loading condition. The evaluation of whether an arch canopy is suitable for a particular installation depends on many variables, including in-mine conditions and the engineering properties of the structure. However, a general evaluation can be based on a comparison of the arch's maximum crown deflection and a prescribed allowable crown deflection. The design procedure is based on the concept that when an arch canopy is sub-jected to impact loading at its crown and deflects from its unloaded state to maximum crown deflection, the structure absorbs strain energy, both elastic and plastic. As a result, this strain energy can be calculated from a static load-displacement diagram for the structure. The significance of this design procedure is that it gives mine personnel an analytical tool to select an arch canopy to meet the dimensional and functional requirements of a mine entry and a prescribed allowable crown deflection.

Jan 1, 1987

By Richard Quirk

This report describes methods and techniques employed by The Glidden Co. of Cleveland, Ohio, in explorating an ilmenite-bearing sand deposit in Ocean County, New Jersey, during 1960 to determine ore reserve potential and the feasibility of mining and establishing a milling plant on the property for the production of ilmenite concentrate. The property covered approximately 1,250 acres. Comprehensive sampling by water-jet drilling indicated the deposit averaged 20 feet in thickness and contained 4.5 percent heavy minerals, of which 80 to 85 percent was ilmenite and leucoxene. Average depth of the water table as determined by auger boring was 16.8 feet. Pilot plant tests indicated that circular concentrators in combination with spiral concentrators would recover at least 80 percent of the heavy mineral content of the sands. It was estimated that sufficient ore reserve tonnage had been developed to supply the company's Baltimore chemicals division, pigments department, with a suitable grade ilmenite concentrate for a period of 20 years at the present rate of pigments production. The property was designated as Lakehurst mine and plans are in progress for mining development and plant construction.

Jan 1, 1963

By A. George Stern

[In the examination of bentonitic clay suspensions used for oil-well drilling fluids3/ (and for other purposes, such as a core binder for foundry sand) it is important to have comparative tests for evaluating them. A satisfactory clay for these and other purposes should have the property of forming what is commonly called a "gel," but the measurement of this property has been a real problem. To date the solution has not been satisfactory, and some of the difficulties are considered in, this, paper, which describes a simple form of instrument (identified as an eykometer) for measuring the yield point under hydrostatic conditions of non-Newtonian clay suspensions, including those muds that are thixotropic. An oil-well drilling mud serves several functions, many of which depend on the "gel" characteristics of the mud. Among the more important functions are: (a) To plaster the sides of the hole to prevent caving of the walls; (b) to prevent the loss of the circulating fluid out of the hole by seepage; (c) to carry sand and cuttings out of the hole to the surface as they are formed by the rotary drill; and (d) when circulation of the fluid stops for shut-down or other unavoidable cause, to hold the cuttings in suspension by the setting up of the gel, thereby avoiding the difficulties that result when these cuttings are allowed to fall through the fluid and pack at the bottom of the hole.]

Jan 1, 1940

By Charles L. Kimbell

The year 1986 was not a good year for the world's mineral industry from several viewpoints. Levels of production, both of crude minerals and processed forms, registered declines in the cases of a greater number of commodities than the number that recorded increases. The overall value of world crude mineral production was estimated to have increased, but only very slightly in terms of constant dollars to nearly $997 billion. Although there were modest increases in the consumption of all major fuels and most major metals, the latter at least apparently resulted more from drawdowns of inventories than from increased production (fuel consumption increases did come from higher output levels), and consumption of most major fertilizer and chemical commodities (nitrogen, phosphate, and sulfur) were at lower levels than those in 1985. Prices for a number of mineral commodities declined, headed by the very substantial drop in world crude petroleum prices, but also including downturns for a number of metals and industrial minerals as well. There was insufficient information to reliably fix the level of the dollar value of world trade in minerals, for while output was up in the case of some large-volume materials such as iron ore, coal, and crude and refined petroleum, suggesting that the volume of trade in physical units may have increased, declining prices may well have offset quantitative gains.

Jan 1, 1988

By John A. Kiefer

Ground fault and overcurrent protection criteria for coal mine a.c. distribution systems were examined under a Bureau of Mines funded investigation. The report begins with a literature review which discusses relaying topics including instrument transformers, ground-fault pickup methods, static relaying, and comparison of relaying techniques. A chapter on ground-fault relaying provides recommendations for maximum and minimum pickup levels as a function of maximum ground current and power system line-to-ground capacitance. Research in the area of phase overcurrent protection has resulted in a complete set of procedural recommendations for the selection and setting of overcurrent relays and current transformers, molded-case circuit breakers, and distribution system fuses in coal mine power systems. The final chapter, which discusses relay system maintenance, introduces a unique test set which was developed by KETRON and used to test the performance of relaying systems in coal mines.

Jan 1, 1980

By William A. Beck

"In 1912 bauxite was discovered in the Andersonville district, which lies in the 28th and 29th land districts of Georgia and comprises parts of Sumter, Macon, and Schley Counties. Mining was begun in May 1914 by the Republic Mining & Manufacturing Co. Considerable ore has been produced in this region since that time by individual interests and by the American Cyanamid & Chemical Corp., which acquired the property formerly owned by the Republic Co.The area was examined in the fall of 1941 by representatives of the Bureau of Mines and the Geological Survey, after which a prospecting program was begun by the Bureau. Drilling was started on December 26, 1941, and continued until November 18, 1943. A total of 1,192 holes was drilled in the district, and 3,679 samples were taken and analyzed.Mineral exploration agreements were signed by 146 property owners covering 42,128 acres. Holes were drilled on 121 of these properties, which have a total area of 38,778 acres.Drilling under this project disclosed several new deposits, of which four have been completely delimited. Previous prospecting in this area by mining companies did not find bauxite, as it lies under heavy overburden. Work by the Bureau indicates 14,412,000 long tons of ore containing 30 percent or more alumina. The total tonnage is divided as follows:Georgia State Highway Routes 26 and 4-9 traverse the district. The Central of Georgia Railroad passes through the center of the entire district (see fig. 1).The project was initiated by J. R. Thoenen, supervising engineer, Non-metals Mining Section, Mining Division, Bureau of Mines. It was under his general supervision until July 1942, after which it was under the general supervision of E. J. Lintner and Rowe McCrae, district engineers for Georgia, South Carolina, and Flordia, respectively.John C. Feeley, Jr., was project engineer from December 1941 to April 1942. Other engineers who assisted in the work on the project are R. E. Babcock, T. M. Romslo, Don M. Coulter, and Walter T. Lewiecki.Acknowledgment is due the metallurgical staffs at College Park, Md., and Tuscaloosa, Ala., for analyses of samples and beneficiation tests.Acknowledgment is also expressed to Alfred D. Zapp, M. W. Harris, Elmer Kneedler,and Parke D. Snavely, of the United States Geological Survey, for their aid, data, and maps.Bauxite was discovered in the Andersonville district in 1912 on lot 187 of the 28th land district, in Sumter County. This lot is situated about 1.5 miles west of the Flint River, on the south slope of the valley of Sweetwater Creek. Mining was started in May 1914 by the Republic Mining & Manufacturing Co. This and adjacent properties were acquired in 1930 by the American Cyanamid & Chemical Corp., which has been operating there since."

Dec 1, 1949

By A. George Stern

In the examination of bentonitic clay suspensions used for oil-well drilling fluids3/ (and for other purposes, such as a core binder for foundry sand) it is important to have comparative tests for evaluating them. A satisfactory clay for these and other purposes should 'rave the property of forming what is commonly called a "gel," but the measurement of this property has been a real problem. To date the solution has not been satisfactory, and some of the difficulties are considered in, this, paper, which describes a simple form of instrument (identified as an eykometer) for measuring the yield point under hydrostatic conditions of non-Newtonian clay suspensions, including those muds that are thixotropic. An oil-well drilling mud serves several functions, many of which depend on the "gel" characteristics of the mud. Among the more important functions are: (a) To plaster the sides of the hole to prevent caving of the walls; (b) to prevent the loss of the circulating fluid out of the hole by seepage; (c) to carry sand and cuttings out of the hole to the surface as they are formed by the rotary drill; and (d) when circulation of the fluid stops for shut-down or other unavoidable cause, to hold the cuttings in suspension by the setting up of the gel, thereby avoiding the difficulties that result when these cuttings are allowed to fall through the fluid and pack at the bottom of the hole.

Jan 1, 1940

By Mark K. Larson

A constitutive model for rock interfaces based on the principles of static fatigue is proposed. The model is applicable to weak rock or joints with cohesion. Friction and dilation are decreased as plastic work increases. At equilibrium, the creep time increases by one time-step interval, and interface cohesion at each node decreases according to a power function. A constant-load, direct-shear simulation showed that the model is cap- able of mimicking constant-rate and tertiary creep and predicting failure. Tests on core from a coal mine showed constant-rate and, sometimes, tertiary creep, but also weak transitory creep. The cohesion deterioration function may need modification to simulate primary-phase creep. If model parameters are known for a site, the model can predict the onset of tertiary creep and failure. Such predictions can help engineers make better entry design and support decisions, which will reduce the likelihood of roof falls and increase safety for underground miners.

To predict the spontaneous combustion potential of bituminous coals using a simple expression based on an easily acquired coal property. Background Approximately 20% of underground coal mine fires in the United States since 1978 have been attributed to spontaneous combustion. Spontaneous combustion fires in underground mines are most likely to occur in gob area; and are difficult to detect and to extinguish by direct fire fighting methods. Often, sections of the mine or the entire mine must be sealed for long periods, at a great economic loss to the mine operator, mine employees, and the surrounding community. It is conservatively estimated that the cost of scaling a large mine is about $50 million.

Jan 1, 1989

By Richard O. Kneisley

An empirical method, based on U. S. Bureau of Mines field studies in several Western U.S. coal mines, is presented for sizing gate road yield pillars. Discriminant analysis was used to generate functions separating successful from unsuccessful case studies. These functions relate the pillar width-height and extraction ratios and a pillar development factor to the Coal Mine Roof Rating System (CMRR), and are assumed to establish three criteria that other entry systems, under similar conditions, must satisfy. A program, Pillar Sizer, from user-provided inputs, generates a range of pillar sizes that meets the proposed criteria. Although the analysis is based on a sample consisting primarily of two-entry systems, the derived expressions generate pillar sizes closely agreeing with observed, two-entry and three-entry in situ pillars. It is concluded that the proposed approach should assist mine operators estimate entry system yield pillar dimensions.

Jan 1, 2010

This report includes a short history of uranium and its uses, mineralogy of common uranium minerals, and information on the use of electronic prospecting equipment and tests for detecting the presence of uranium. Details are given on geologically favorable areas and formations and practical methods of prospecting. Some information is given on the staking of claims, what lands are open to prospecting, and methods of securing mining rights. A forecast of the economic outlook for uranium is included. Appendixes give sources of additional information and a list of libraries where unclassified Atomic Energy Commission reports may be consulted. Because the increasing use of uranium by industry has revived interest in prospecting and exploration for this element, the Bureau of Mines has issued this report, which brings up to date and expands the subject matter of a hand- book on uranium exploration and production published in 1956.l

Jan 1, 1968

By J. M. Davidson

The potassium mineral polyhalite (K2SO4.MgSO4.2CaSO4.2H20) found in large deposits in western Texas and southeastern New Mexico is associated with varying amounts of halite (sodium chloride, NaCl) and anhydrite (calcium sulphate, CaSO4). Although the anhydrite, because of its low solubility and slow rate of solution, is relatively inert, the halite is dissolved immediately in any process solution with which the polyhalite comes in contact. Limited quantities of sodium chloride in the liquors used for the hot extraction of polyhalite materially improve the results obtained,4 but only a very small sodium chloride content may be desired in the entering polyhalite in other procedures, such as Bureau of Mines process 75. In. all of the processes suggested for the recovery of potassium sulphate from polyhalite the control of the sodium chloride content will be desirable, if not absolutely essential to efficient operation. OCCURRENCE OF HALITE IN POLYHALITE A preliminary estimate of the amount of halite associated with typical deposits of polyhalite may be derived from drill cores, although it should be remembered that only 50 or 60 core tests have been made in the many hundreds of square miles of the Permian basin. From a mineralogical study of 41 of these cores, Schaller and Henderson6 state: In many of the sections of core that seem when viewed by the unaided eye to consist essentially of polyhalite, both halite and anhydrite are present in greatly varying quantities - with very minor quantities of clay and magnesite.

Jan 1, 1934

By Donald I. Bleiwas

The U.S. Bureau of Mines has evaluated the potential availability of nickel from 36 deposits or districts in 16 market-economy countries (MECs), analyzing more than 95 percent of production in those countries. This study indicates the quantity of nickel available on the basis of net production costs and total costs with a 0-pct and a 10-pct discounted cash flow rate of return (DCFROR). Costs of production are expressed in dollars per pound of recovered nickel. The study also indicates sensitivities of the cost of production to energy, labor, and other factors. The studied deposits and properties contain approximately 33 Mmt of recoverable nickel. About 26 Mmt of nickel is potentially recoverable from laterite deposits, of which 4.5 Mmt can be produced at $2.50/lb or less with a 0-pct DCFROR. Approximately 7 Mmt of nickel is potentially recoverable from sulfide deposits, of which about 6.3 Mint could be produced at $2.50/lb or less at a 0-pct DCFROR. The price of nickel averaged above $6.00/lb in 1988. Sensitivity studies performed for both laterite and sulfide deposits indicate that the total cost of producing nickel from laterites is most sensitive to increases in energy costs and that the total cost of producing nickel from sulfide deposits is most sensitive to increases in labor costs; sulfides are also affected by changes in revenues from byproducts.

Jan 1, 1991

By F. N. Kissell, C. M. McCulloch, Maurice Deul, J. R. Levine

The methane content of virgin bituminous coalbed can now be measured accurately in the field with exploration core samples from vertical boreholes. The gas content of the coal per unit weight can be used either to design a mine ventilation system or to determine if degasification of the coalbed will be necessary before mining, and to determine the gas resources in the coalbed. The equipment necessary to conduct the test costs less than $50. The gas content of the coal in place in the ground is determined by summing the gas lost from coring, gas measured during desorption, and the residual gas in the coal. Upon removal from the borehole, the core sample is placed in an airtight container and desorbed for several weeks until the desorption rate is below 0.05 cm3/g for 5 consecutive days. The gas lost from the core while it was being cored and the residual gas are estimated by a new graphical method. The amount of gas remaining depends upon whether the coal is friable or blocky. Friability appears to relate to the depth of the sample below the surface, fixed carbon percentage, Hardgrove grindability index, and proximity to tectonic disturbance. Friable coals emit nearly 96 pct of the total gas during desorption whereas a blocky coal emits only 60 pct of its total gas. Coalbeds that are ill defined as to their blocky or friable nature must be tested in the laboratory for unambiguous analysis.

Jan 1, 1975

By I. L. Nichols

The inplace cyanidation leaching of gold from placer deposits is a potential method for treating gravels too deeply buried and too low in gold content to be processed economically by conventional dredging methods. Laboratory experiments were made to evaluate those placer cyanidation factors adaptable to small-scale studies. The variables investigated included gold particle size and location in sand beds, cyanide solution flow rate, and cyanide solution strength as factors affecting gold solubility rates. The solution flow rate, in turn, was influenced by variables such as bed slope, solution head pressure, and sand size, and the effects of these factors were studied. Free gold, minus 150-mesh and finer in size, is rapidly dissolved by dilute cyanide solutions from mixtures of gold and silica sand prepared to simulate placer deposits. About 94 percent of minus 325-mesh free gold was extracted in 5 hours from silica sand mixtures, and 94 percent extraction of minus 150-mesh gold was obtained in 21 hours with 0.1 percent NaCN solutions. Moving solutions were almost twice as effective in leaching free gold from silica sand mixtures than stagnant solutions.

Jan 1, 1971

By G. L. Fitzpatrick

A portable optical instrument for performing multispot laser vibrometry is described. The instrument is capable of measuring arrival times, surface motion frequency, and surface velocity and displaying these quantities in various useful ways. Sigma Research is currently pursuing the development of such optical measuring systems for the evaluation of structures in rock by non-contact interferometry methods. This work was sponsored by the U.S. Department of Interior (U.S. Bureau of Mines) under a Small Business Innovation Research (SBIR) contract number J0145075. The goal of the work was to develop a portable tripod mounted measuring system which can be set up at arbitrary distances (up to 30 meters) from a surface and project four in-line laser sample beams on this surface. A light receiving telescope gathers the scattered light from these four spots and provisions are made to mix this light with a reference beam from the laser. Four photodiodes are employed to determine the resultant interference signals which characterize the motion (particle velocity, frequency, amplitude) of the four illuminated spots on the surface under sudy. Information of this type can then be used to characterize the elastic or mechanical properties of the surface in question. In some cases (if more than four spots are involved) this surface information could be back propagated to draw inferences about the internal state of the material volume bounded by this surface.

Jan 1, 1987

By D. Harrington, C. W. Owings

The mining industry is gradually realizing that safety education and safety inspection are economic factors that may not be overlooked as a means of reducing operating costs . Many mine operators , however , have failed to realize the benefits of safety , and the efforts of the more progressive mining companies are offset by the carelessness of neighboring companies when the accident records of a community or a State or the nation as a whole are considered . This tendency is indicated by the data collected by the safety division of the United States Bureau of Mines . During the fiscal year ended June 30, 1930 , relatively definite information: was secureä concerning 34 mine explosions , 24 mine fires , and 29 miscellaneous accidents ; these accidents are by no means all of the explosions , fires , and miscellaneous accidents which occurred in the mines of the United States during the period; but the data on the fires and explosions constitute a record of all of those types of accidents that were called specifically to the attention of the safety division , and the miscellaneous accidents include those on which definite , detailed data were obtained by the safety division .

Jan 1, 1931

By R. D. Berkenkotter

Titanium and iron assays obtained from cores of three diamond-drill holes from the Cebolla Creek titaniferous iron deposit were evaluated by statistical techniques to obtain information concerning the mineral characteristics of the deposit and to make a preliminary determination of sampling requirements for the deposit. A range of sample volumes representing sizes from one-sixth NX core 2 feet in length through full NX core 10 feet in length were prepared by split-ting the NX core with a diamond saw and combining pulverized splits. Results indicate the existence of at least two statistical populations having different average grades of iron and titanium. Each has an assay frequency distribution that is not normal but is highly peaked (leptokurtic). Frequency distributions of assays from specific altered zones of the drill holes appear to be normally distributed. Increasing the cross-sectional area of the sample unit to change assay volume did not result in significant changes either in assay values or the resulting frequency distributions of assays. However, when assay volume is increased by increasing sample interval, the shape of the assay frequency distribution changes, and a normal distribution of assays is approached. Positive correlation exists between titanium and iron assays. The degree of correlation, although very significant, is too low to use for prediction purposes. Although the amount of data from three widely separated drill holes is not sufficient to establish an average grade for this large deposit, it indicates a range of expected assay values and provides some information for determining requirements of future sampling for evaluation purposes.

Jan 1, 1963

By Reynold Q. Shotts

A study was made of the coal resources of an area in Jackson County, Ala., forming a part of the Flat Rock, Henegar, and Stevenson quadrangles. The area studied is a portion of the Plateau coalfield on Sand Mountain and is near the Tennessee Valley Authority's Widows Creek steamplant. Since no detailed geological study of this area had been published, some reconnaissance work was done. The coalbeds and adjacent strata such as sandstones, conglomeratic sandstones, and conglomerates were studied. Available drill logs, together with the areal geology, provided sufficient information to permit correlation of the coalbeds and an estimation of coal reserves. For all categories of reserves, computed on a regional basis, a total of 72,920,000 tons of coal more than 14 inches thick is estimated for the areas studied in Stevenson, Flat Rock, and Henegar quadrangles. Of this tonnage, 40,001,000 tons is estimated to have less than 60 feet of overburden. The total measured coal reserves for the above three quadrangles are 16,359,000 tons, with 12,411,000 tons under less than 60 feet of cover.

Jan 1, 1966

By W. H. Ode

Because trade increased among various nations after World War II, the Coal Committee of the Economic Commission for Europe established a Classification Working Party in 1949 to develop an International system for classifying coal. Although national classification systems existed, they had been developed in accordance with characteristics of domestic coals without reference to coals of other countries. Terms for describing similar or identical coals differed in each nation. This caused confusion in evaluating coals shipped in international trade and also hampered exchange of technical information on problems of coal utilization. Experts4/ participating in the classification project early in their work agreed that two systems should be formulated, one for the higher rank coals or so-called "hard" coals in European terminology and the other one for the lower rank coals, the latter designated mainly as brown coals and lignites in the various countries. Rank refers to the degree of metamorphism (progressive alteration) in the natural coalification series from lignite and brown coal to anthracite. The system for classification of hard coals was published late in 1956 as a document of the United Nations.5/ Results of a study for applying this system to American coals were published in 1958.6/

Jan 1, 1960