Search Documents

By N. Malakondaiah

Several growth chamber and laboratory experiments were conducted to study the germination behavior of plant species on mine spoils and plant growth responses to nutrients on spoils and topsoils. Experiments were conducted to study the germination potential of some native and introduced species under various conditions. The seeds of green needlegrass, side oats grama, thickspike wheatgrass, crested wheatgrass, birdsfoot trefoil and emerald crownvetch were less tolerant, whereas those of alkali sacaton. durar hard fescue, slender wheatgrass, yellow sweetclover and alfalfa were most tolerant to the sodic mine spoil conditions. Addition of leonardite improved the germination potential of some of the poor genninators. Slender wheatgrass and yellow sweetclover were used as test plants to study the fertility status and productivity potential of stockpiled topsoils and spoils collected from Center. Glenharold and South Beulah of North Dakota. The topsoils were neither saline nor sodic but low in N and P. The spoils were neutral to alkaline with SAIL of 12-32, EC of 1.8-5.5 mmhos/cm, Olsen&apos;s P< µ4g/g, and total N <0.07%. Application of N and P together to the topsoils increased the yield of wheatgrass and sweetclover by 88% and 70% of their respective maximum yields, whereas near maximum yields were obtained for both the species by the same treatments to the spoils. The average yields on topsoils were higher than the yields on spoils. The concentrations of major nutrients were higher in plants grown on topsoil, whereas the opposite was true with the concentrations of Mn, Zn, and Cu. Growth chamber experiments were also conducted to study the growth responses of alfalfa, oats and slender wheat grass by the application of Mn and Zn to a sodic coal mine spoil which was previously used for pot culture experiments. Significant growth responses to Mn and Zn were observed in alfalfa but not in oats or slender wheatgrass. Fertilizing the spoil with Mn along with NPK increased the yield of alfalfa to 85% and with Mn + Zn to 99%. Growth responses and plant composition results of this study confirm that the application of major nutrients to spoils can accentuate Zn and Mn deficiencies in some plants.

Jan 1, 1982

By J. B. Zadra

Tungsten, a comparatively new metal, is one of the important strategic war materials. In peacetime, tungsten is widely used as a filament in elec¬tric lamps and electronic tubes and is a vital constituent of some of the most important industrial alloys. High-speed tool steel containing tungsten and stellite alloys containing cobalt, chromium, and tungsten are extremely hard and resistant to corrosion. These alloys and the tungsten carbides are unequaled as cutting tools and in other wear-resistant applications. They play a prominent role in the present era of mass production. Alloys containing tungsten resist oxidation at high temperatures and have been key alloys in the development of modern aircraft. The adaptability of tungsten to new uses is expanding, particularly in the high-temperature range. Domestic production of tungsten has come from a large number of deposits in 17 of the 49 States; but, of the total domestic output from 1900 to 1956, more than 80 percent was produced from mines in North Carolina, California, Colorado, and Nevada. The average tenor of the mined ore was less than 1 percent tungsten trioxide (W03).

Jan 1, 1959

By G. W. Jones

The Bureau of Mines has advocated the use of stenches as warning agents in metal mines and in gas-distribution systems since 1920 A considerable amount of research has been conducted on ethyl mercaptan and other compounds to determine their effectiveness when used for this purpose.4/5/6/7/8/9/10/11/12/13/ Miners are warned of danger by a stench injected, in measured quantity, into a compressed-air line through which it is rapidly carried to the working faces, where it escapes from the compressed-air equipment and imparts a characteristic odor to the air. This method is not applicable to mines where only a limited number of com-pressed-air lines are used, as for example, many coal mines; the ventilation currents available in these mines may be too slow for warning purposes.14/

Jan 1, 1954

By Alan D. Hartman

Standard metering of electric arc furnaces usually uses root mean square (RMS) or true root mean square (TRMS) measurements for determining power. Only sinusoidal signals are accurately described by RMS meters, and dc or high-frequency components normally are lost in standard TRMS metering. This can lead to inaccuracies when electrical signals are not sinusoidal, contain dc components, or include fast risetime perturbations, as is the case with the electric signals from an electric arc furnace. Electric arc furnace electrical waveforms, observed in research carried out by the U.S. Bureau of Mines, show high-frequency components and significant deviations from sinusoids. These perturbations and distortions make metering difficult for standard power meters. The inaccuracies in metering can cause further problems if those sensors are used in control systems. For control strategies requiring rapid response, any averaging scheme loses information that can be used in control decisions. In order to obtain better signals for both monitoring and control, a study of instantaneous, RMS, and TRMS power monitoring devices was conducted. From this study it was concluded that precision integrated circuits should be used to obtain instantaneous power with a bandwidth of at least 25 kHz. The information from these devices is more representative than that of standard meters and can be used in predictive control.

Jan 1, 2010

Permit quicker, safer clearance of hang-ups in the ore passes and chutes of underground mines. Approach Develop a device that can be operated from a safe distance to explosively propel a projectile into the hang-up. How It Works The Hang-Up Clearance Module, consisting of a stand, steel disk, explosive charge, and aiming device, is placed at a location convenient for line of sight aiming at the hang-up. This placement can be more than 100 feet from the target. Once aimed, the charge is remotely detonated, and the disk is converted by explosive force into a slug and propelled to the hang-up, bringing it down. The steel disk and an explosive charge are contained by a plastic casing. A small booster which is placed at the rear center of the explosive makes up the last component of the charge. Initiation is accomplished by standard means such as detonating cord or a number 8 blasting cap. When Initiated, a detonation wave travels through the explosive, inverting and consolidating the steel disk into a large slug. This slug is propelled at high velocity to the hang-up, delivering more than 5 million foot-pounds of energy on impact.

Jan 1, 1981

By D. Harrington

"One of the underlying reasons for the establishment of the United States Bureau of Mines was the desire to promote greater safety in the mining and allied industries. Safety continues to be an important feature in the work of the bureau, and during the fiscal year 1929-30 the Bureau of Mines allotted $387,510 to the safety division out of a total appropriation of $2,249,670 (other than for helium).The safety division personnel consists of 22 engineers, 2 mine safety commissioners, 3 senior foreman miners, 18 foreman miners, 16 first-aid miners, 16 clerks, 10 cooks, and 3 laborers, a total of 90 persons. These safety workers are distributed through the 10 districts into which the United States has been divided for administration purposes. During the year 3 engineers, 1 senior foreman miner, 4 foreman miners, and 4 first-aid miners left the service. In general these men left the service to take up more lucrative positions.The 10 all-steel mine-rescue cars have headquarters as follows: Car 1, Reno, Nev.; Car 2, Raton, N. Mex.; Car 3, Pittsburgh, Pa.; Car 4, Terre Haute, Ind.; Car 5, Pineville, Ky.; Car 6, Pittsburg, Kans.; Car 7, Huntington, W. Va.; Car 8, Duluth, Minn.; Car 9, Butte, Mont.; Car 10, Des Moines, Iowa. There is also a mine-rescue car with headquarters at Juneau, Alaska. In addition, there have been established 11 mine rescue stations as follows: Birmingham, Ala.; Berkeley, Calif.; Seattle, Wash.; Evansville, Ind.; Jellico, Tenn.; McAlester, Okla.; Norton, Va.; Vincennes, Ind.; Wilkes Barre, Pa.; Salt, Lake City, Utah; and Pittsburgh, Pa.Every mine-rescue car and station is fully supplied with equipment and devices for use in case of mine fire or explosion, and at each station is an up-to-date automobile truck. At time of amine disaster the bureau's forces are immediately placed at the disposal of the authorities, State or company, with a view to giving such assistance as may be desired or available.The activities of the safety division at ordinary times are directed largely to securing and disseminating data on safety in mining. Among the numerous studies made, or being made, concerning safety and health in mining are those in connection with the causes and methods of prevention of mine explosions, explosibility of dust and gases, explosives and blasting, haulage, electricity, falls of persons or material, ventilation, dusts, high temperatures, timbering, lighting, machinery, and in fact practically anything which results or may result in acci¬dents of any kind in or around mines."

Nov 1, 1930

By L. D. Gent

This report reviews the current state of the art of remote control techniques for underground continuous miners. A delineation of aspects requiring additional data is presented. Also a summary and delineation are presented in overview form for the related section functions: roof control, haulage, ventilation, power supply and rock dusting. The automated remotely controlled continuous miner project is a long-range research effort. However, the program has been divided into intermediate steps resulting in incremental production increases throughout the program. Data are developed relating the impact of our proposed research and development accomplishments to potential productivity impact.

Jan 1, 1975

By M. L. Bowser

Pulse-forming circuitry is described for use in explosives research that requires precise synchronization and control of events in order to investigate detonation parameters. Included are pulse generators for oscilloscope sweep control, counterchronograph actuators, and a raster-type oscillographic method for the determination of velocities of detonation that are applicable to studies on solid, liquid, and gaseous detonations. INTRODUCTION Prom time to time, requests have been received for information on electronic circuitry used in explosives work at the Explosives Research Laboratory, Bruceton, Pa. The methods used are not entirely original;4 5 6 however, modifications of earlier techniques and some novel design aspects have resulted in time-tested methods that warrant a more detailed description.

Jan 1, 1962

By A. C. Fieldner

"INTRODUCTION In a previous report3 prepared for the American Gas Association, the influence of washing coal on coke properties and on gas and by-product yields was discussed on the basis of answers to questionnaires sent to coke-oven superintendents and a review of the literature on the subject. This review indicated that the elimination of free impurities by cleaning coal improved coke quality by (a) reducing ash and sulphur, (b) decreasing clinker trouble in burning the coke, (c) diminishing cross fractures in the coke, resulting in greater resistance to breakage on handling, and less small coke and breeze, and (d) greater uniformity in chemical composition and physical properties of coke. Washing also reduced the sulphur in coke and gas and increased the yield of gas and by-products per ton of dry coal charged.This paper is supplementary to the previous report and presents some experimental data obtained with Pittsburgh bed coal from Pennsylvania and Mary Lee bed coal from Alabama.ACKNOWLEDGMENTSGrateful acknowledgment is made to F. J. Pfluke, of the Rochester Gas and Electric Cc., of Rochester, N. Y., for the plant test data on screened lump and washed coal; and to Ray W. Arms, Manager of the Coal Cleaning Department, of Roberts & Schaefer Co., of Chicago, for the data on effect of air cleaning."

May 1, 1931

By G. K. Derby

The Bureau of Mines investigated methods for removing dragline bucket wire rope terminations with the objective of finding efficient methods that are safer than the method most commonly used at U.S. surface mines, which is to use the explosive impact of a projectile fired from a cannon to remove the rope termination. Removal of a wire rope termination for repair or replacement requires separation of the wedge and socket that lock together to secure the rope end. The Bureau investigated currently used methods and improved upon and tested two safer alternate methods for removing wire rope terminations. A cannon test program was conducted, using 40-and 50-gr primer (detonating) cord, to establish the possible force produced with a 4-in-bore cannon and a 55-lb projectile. Wedge and socket units supplied from cooperating mines were separated under controlled conditions to establish data on separation force requirements. The two alternate methods investigated were use of the force generated by (1) a pendulum ram and by (2) a portable hydraulic pusher. Both methods are capable of providing sufficient force to effect wedge and socket separations on draglines with up to 78-yd3 buckets under normal conditions.

Jan 1, 1984

By Donald C. Strimbeck

The Bureau of Mines designed a down-fired refractory-lined combustor that efficiently burned pulverized coal to produce a gas suitable as working fluid for an open-cycle gas turbine. The gas contained relatively little carbon, so the load on the ash-separation equipment was significantly reduced. Moreover, reduction in carbon content of the gas increased the average density of the solid particles making them more amenable to removal by centrifugation. Centrifugal-type separators failed to remove sufficient ash; however, to limit blade wear enough to achieve operating periods generally deemed necessary for commercial practicability.

Jan 1, 1969

By Berk. A. A.

"INTRODUCTION Corrosion of sections of piping used in steam-heating systems is frequently regarded as unavoidable, and periodic replacement is provided. Surfaces exposed to newly condensed steam appear to be especially vulnerable to attack. As an added nuisance, solid products of the corrosion tend to accumulate, plugging return lines.The trouble is ascribed in the main to carbon dioxide and oxygen 3/ 4 / 5/ 6/ dissolved in the condensate. When oxygen is the principal factor, the corrosion usually is characterized by pitting. Carbon dioxide tend3 to cause an acidic condensate which dissolves the metal more uniformly and produces the familiar failure at threaded areas where the piping is relatively thin, and where high stress may tend to acceletate the attack. Carbon dioxide enters the system with the feedwater, generally in a combined form such as carbonates and bicarbonates. Oxygen enters both with the raw feedwater-and as air leaking into lines under partial vacuum. The larger central-heating plants have sought to reduce corrosion by eliminating these gases as much as possible. A smaller plant ordinarily lacks the equipment and technical supervision required for this purpose."

Jun 1, 1944

By C. W. Davie

"This paper is the second of a series of progress reports4 on a study of the hydrometallurgy of manganese which is being conducted in an endeavor to make possible utilization of the large deposits of low-grade domestic manganese ores that occur in several States.There are at least four processes in which a knowledge of the action of SO2 gas on manganese oxides at elevated temperatures may prove of value.One of these involves dissolution of manganese from ores. The Bureau of Mines has investigated the hydrometallurgy of manganese by a process in which SO2 gas, a waste product at many smelters, is passed into water to form a solvent for manganese. Although several manganese minerals were readily dissolved, rhodochrosite (MnCO3) was attacked but superficially.5 Recent experiments have shown that a roast at 650 to 9000 C. converts the manganese of rhodochrosite to a form that is quickly dissolved by a weak SO2 solution.6 Introduction of smelter gases containing much as 5 per cent SO2 during such a roast would not add much to the cost of the operation, and might result in the formation of considerable water-soluble manganese sulpate.Another case involves a subsequent step in the hydrometallurgical process, namely, the formation of oxides of manganese with simultaneous evolution of SO2 by the heating of the MnSO4 produced by evaporating its solution.A third has to do with the roasting of zinc sulphide ores containing manganese as a preliminary to leaching. During purification of the solutions to be used for the electrolytic deposition of zinc the iron must be oxidized to make possible its removal. Manganese dioxide has been used for this purpose,7 and since manganese compounds are present in some zinc concentrates,8 it is of interest to learn what happens to the manganese in a zinc sulphide or on roasting, and what portion of the manganese in the roasted product might be available for oxidation."

Oct 1, 1930

By Jeffrey Shawn Peterson

The testing procedures of the u.s. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break-flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 2010

By S. H. Lorain

This paper is a preliminary report on recent lode gold mining activity, operating conditions, and mining and milling methods at properties in production in September 1936 in the gold belt of northeastern Oregon. A few inactive properties are described also. Districts, inactive in 1936, that have been important producers at some time in the past are mentioned briefly. This is one of a series of similar papers describing western mining districts. The past production record of the gold mines of northeastern Oregon entitles the region to be ranked as one of the important gold-mining regions of the United States. Although comparatively inactive for many years, lode mining in the region has recently undergone a marked revival.

Jan 1, 1938

By Sara Jane Boles

In recent years the demand for products of greater refractoriness has placed an ever-increasing emphasis on ceramic materials, including the metallic oxides. Magnesia (MgO) is one of the most important of these oxides, exhibiting, as it does, high electrical resistivity, high slag resistance, and a melting point of 2,800° C. However, magnesia has a tendency to hydrate in the presence of water and to volatilize above 1,500° C. in certain kiln atmospheres and has a comparatively low resistance to thermal shock. Because of these disadvantages, the previously listed advantages inherent in this material have been largely overlooked, and research on magnesia has lagged behind that on oxides such as alumina and zirconia. This bibliography has been prepared in an effort to present to Government and industry a comprehensive picture of the prospects for greater utilization of magnesia as a refractory material in future research. To provide as selective and accurate a collection as possible, the references included cover magnesia in a pure state, not as an additive or in combination with other materials. However, several references discuss the effect of minor impurities (less than 5 percent of the total) on the properties of magnesia, as these papers are considered to be of special importance. A few references to articles on forming techniques are also included, as they are valuable additions to the overall treatment of the subject. The processes used in obtaining and refining the raw materials are adequately covered in earlier publications and are excluded. A number of references are omitted as being of questionable value in enhancing the cumulative study of pure magnesia as an ultra-high-temperature refractory material.

Jan 1, 1962

By Sean Gallagher

The human body is remarkably adaptable and capable of performance in a wide variety of environments and circumstances. It cannot be said, however, that the body is capable of performing equally well under all conditions. In fact, when faced with certain types of tasks or environmental demands, the body may have to adapt using methods that result in substantial performance limitations. Such a phenomenon is evident when workers must adopt unusual or restricted postures during performance of physically demanding work tasks. For the purposes of this discussion, the term "unusual posture" will be considered as any working posture other than typical standing or sitting positions. The term "restricted posture" designates postures that are forced upon workers due to restrictions in workspace. The vast majority of ergonomics research has focused on establishing design criteria for work involving standing (e.g., Snook and Ciriello, 1991; Waters et al., 1993) or seated postures (e.g., Grandjean, 1988), and understandably so. However, it must be recognized that there are numerous jobs (e.g., underground miners, aircraft baggage handlers, plumbers, agricultural workers, mechanics, etc.) where workers must perform in less desirable postures such as kneeling, stooping, squatting, and lying down (Haselgrave et al., 1997). Unfortunately, experience has shown that many ergonomics techniques used to analyze or design standing or sitting workstations often do not adapt well to situations where a restricted

By Guy A. Johnson

This Bureau of Mines report summarizes the results of efforts to develop reasonably priced, reliable mine shaft fire and smoke protection hardware for metal and nonmetal mines. The hardware was incorporated into a viable prototype system that would minimize fire and smoke hazards. The design of the system had to be sufficiently flexible to be utilized in a wide variety of metal and nonmetal mine shaft and shaft station configurations. As a result of long-term, rugged field tests, an improved (second generation) system was developed. The hardware is now commercially available.

Jan 1, 1978

By Bruce I. Thomas

The Fairbanks mining district forms an arc 40 miles long and 8 miles wide on the north side of the Tanana Valley in central Alaska. This is a region of broad valleys and rounded hills that range in elevation from 600 to 2,600 feet Lode-gold production started in 1910 and has continued sporadically to the present, but the largest single mine produced only 40 tons per 24-hour day. Total recorded lode-gold production of the district is 241,000 fine troy ounces of gold from ore that averaged 1.32 fine ounces per ton. The ore was mined chiefly from narrow veins and veinlets alined along anticlinal folds at Ester Dome and the Pedro Dome-Cleary area. The only proven reserves are reported to be at the Ryan Lode at Ester Dome and at the Keystone Mines, Inc., holdings in the Pedro Dome-Cleary area. An inferred lode-gold resource for the district of approximately 4,000,000 ounces is considered to indicate only the order of magnitude of the lode-gold potential because of the absence of detailed data needed to evaluate the numerous deposits.

Jan 1, 1973

By Robert L. Lagace, Michael A. Grossman, Alfred G. Emslie

This supplement to the final report is a collection of interim and monthly reports and working memoranda prepared during the course of this program to document the progress, methods and results of the work. The supplement is divided into the self-contained sections briefly described below. I. SELECTED MONTHLY TECHNICAL LETTER REPORTS - This section is a collection of selected monthly technical letter reports that briefly summarizes the chronological development of the analyses and results, including the different concepts, theoretical approaches, and methods of data reduction and analysis explored, and the discoveries, insights and findings made along the way. More detailed treatments of the key developments and results are presented in the interim reports and working memoranda reproduced in subsequent sections of this supplementary report, and in the separately published final report. II. BACKGROUND THEORY FOR MEASUREMENT PROGRAM ON MEDIUM AND HIGH FREQUENCY RADIO TRANSMISSION IN COAL SEAMS - Working Memorandum - This working memorandum gives the initial background theory needed to guide the planned measurements and data analyses of this program to describe the propagation of radio waves-in coal seams for the frequency range of 50 to 5000 kHz. III. MODELLING AND DATA ANALYSIS OF IN-MINE ELECTROMAGNETIC WAVE PROPAGATION - Interim Report - This interim report presents detailed treatments of the data analysis and modelling techniques used, and the associated results obtained from conductor-free area propagation data measured by T. Cory in the first set of six coal mines. The mines were located in three highcoal seams; the Pittsburgh seam in northern West Virginia, the Pocahontas No. 3 seam in Virginia, and the Herrin No. 6 seam in Illinois. IV. ANALYSIS OF MF PROPAGATION DATA FROM MARGARET NO. 11, NANTY GLO, EHRENFELD, AND ADRIAN COAL MINES - Interim Report - This interim report presents detailed treatments of several improved data analysis and Modelling methods applied to, and results obtained from, conductor-free area propagation data measured by T. Cory in the second set of four coal mines. These mines were located in three low-coal seams; the Upper Freeport seam in Pennsylvania and West Virginia and the Lower Freeport and Lower Kittaning seams in Pennsylvania. In addition, this report contains a reprint of two papers presented at a Bureau of Mines sponsored EM Guided Waves in Mine Environments Workshop held in Boulder Colorado. One paper describes the three-layer theoretical model and its application to the conductor-free data from the first six mines, while the second paper describes the theory developed for the coupling of loop antennas to a cable in a mine tunnel in a coal seam, and the model&apos;s application to data in the vicinity of cables taken at the Margaret No. 11 mine. V. A METHOD FOR NONINTRUSIVE, IN-SITU MEASUREMENT OF COAL AND ROCK CONDUCTIVITIES IN A COAL MINE TUNNEL - Working Memorandum - This working memorandum briefly describes a possible direct method, and its potential advantages and shortcomings, for performing in-situ measurements of coal and rock conductivities. VI. MODELLING AND DATA ANALYSIS OF IN-MINE ELECTROMAGNETIC WAVE PROPAGATION FROM 50 to 5000 kHz - Interim Report - This interim report presents a summary comparison of theoretical and experimental results for conductor- free areas in eleven coal mines located in seven coal seams. It also summarizes the findings and their implications for intrinsically-safe, portable radio communications between roving miners.

Jan 2, 1980