Search Documents

By A. B. Hooker, L. C. IlsLey

"Observation of the use of trailing cables in ""mines shows that the chief limiting factor in the life of the cables and their safe use is the smashing or crushing of the cables in service, together with the effects of consequent splicing.Trailing cables are crushed when run over by cars, mining machines; and locomotives or when hit by falls of roof. Crushing damages the insulation and may cause failure at once or in later use. Failure may be either by short circuit between the conductors or by grounding to the track. The failure of a live cable causes electric arcs capable of igniting explosive mixtures of methane and air. Every cable failure in a gassy or dusty mine is, therefore, a real or potential hazard.Some mine operators do not allow the splicing of trailing cables for use in gassy mines, bet require that a damaged cable be immediately replaced and if repaired that it be used only in nongassy mines. Other operators allow the making of temporary splices to permit completion of the shift but require that such splices be remade and vulcanized before the cable is used again.Still other operators allow the continued use of temporary splices, which in general means that a cable is used until the splices give trouble in reeling, or overheat, or pull apart. Then the spliced sections are either cut out or the whole cable is replaced.Splices often determine the useful life of a cable. A splice poorly made may pull apart ueder mechanical strain and cause arcing that burn* the surrounding cable or ignites as or coal-dust. If it has lower conductivity a splice is the first part of the cable to heat; it may become so hot under load that it will burn apart and damage other parts of the cable, or, if it be a soldered splice, the solder may melt and allow parting of the cable. A poorly made splice often has insufficient insulation which may alloy short-circuiting between conductors or permit external contacts capable of giving an electric shock to one handling the cable. The splice is sometimes bulky from too much insulation and takes up too much room on the reel, causing uneven reeling; also by catching on the spooling device the oversized splice may receive expressive pulls and wear. Splicing is therefore a very important factor in the use of trailing cables."

Mar 1, 1932

By L. G. Marshall

Gypsum mining and processing has been one of the principal industries in Iowa for more than 75 years. For most of that period, Iowa has ranked among the five leading States in the production of crude gypsum and of calcined-gypsum products. The Fort Dodge area accounted for 11 percent of the gypsum products produced in the United States in 1956. Before 1927 the output by the major companies came from underground operations, using a room-and-pillar stoping method. At present, all production comes from quarries. The quarry methods at the various properties are similar. This paper describes the quarrying, methods employed in the district and the type of equipment used by each company. The sections on history and geology are, in part abstracts from State annual reports and an Iowa Geological Survey publication.3/

Jan 1, 1959

By Joseph L. Condon

Fifteen shots of three explosives with charge weights of 0.52, 1.1, 3.1, and 5.1 kilograms were fired in a pond to study the seismic effects of detonating explosives in water. Shock pressures and bubble periods were measured with pressure transducers in the water. Vibrations were measured on land in three orthogonal directions with particle velocity gages. Statistical tests indicated that a charge weight exponent of 0.43 best scaled the data. While shock pressures and bubble periods showed considerable differences in explosive performances, the amplitudes of ground vibrations showed less difference, and one prediction equation was therefore derived to estimate vibration amplitudes from all the explosives.

Jan 1, 1970

By D. A. Paice

A power supply to operate fluorescent or mercury vapor lamps from 300 volt dc coal mine trolley wires has been developed for the Bureau of Mines. A high frequency regulated inverter unit incorporates ballasts for a mix of lamp loads up to 650 watts. For 600 volt trolley systems an additional power converter unit was developed to step down the dc voltage to 300 volts for the inverter unit. Both units have operated in a working coal mine for over 12 months without need for servicing. The lamp load in these tests included two 100 watt mercury vapor head lamps and six 75 watt fluorescent lamps.

Jan 1, 1979

By G. L. Oldright

In the previous study that has been made by the authors on smelting in the lead blast furnace, the furnace examined was one that operated under conditions that have been considered as more or less normal up to the present time. That is although the furnace had in its charge a large portion of sinter, it also handled considerable quantities of naturally oxidized direct-smelting ore. Other ingredients, such as the limestone, were also added as fairly coarse material. The charges contained only about 24 per cent of lead. Until the changes incident to modern flotation began to take effect, many lead plants doing semicustom smelting in districts where competition was keen and much of the bonanza ore was exhausted were faced with the difficulty of obtaining enough lead to get a sufficient "lead fall" in the blast furnaces to clean the slag thoroughly and to separate it from the lead. A charge containing 24 per cent of lead would have been considered a very rich one by such smelters.

Jan 1, 1931

By G. L. Oldright

In the previous study that has been made by the authors on smelting in the lead blast furnace,4 the furnace examined was one that operated under conditions that have been considered as more or less normal up to the present time. That is, although the furnace had in its charge a large portion of sinter, it also handled considerable quantities of naturally oxidized direct-smelting ore. Other ingredients, such as the limestone, were also added as fairly coarse material. The charges contained only about 24 per cent of lead. Until the changes incident to modern flotation began to take effect, many lead plants doing semicustom smelting in districts where competition was keen and much of the bonanza ore was exhausted were faced with the difficulty of obtaining enough lead to get a sufficient "lead fall" in the blast furnaces to clean the slag thoroughly and to separate it from the lead. A charge containing 24 per cent of lead would have been considered a very rich one by such smelters.

Jan 1, 1931

By Eugene O. Binyon

"Belt and shaker conveyors, used singly or as combined units, have for many years been an integral part of many coal-mine haulage systems. The belt conveyor has also been used extensively as a main haulage unit in open-pit iron-ore mines of the Lake Superior district, particularly on the Mesabi Range. Few underground metal mines, however, either in the ferrous or non-ferrous branches of the mining industry, use the conveyors exclusively or even extensively for underground haulage. At present, only five iron-ore mines in the entire Lake Superior district have belt- or shaker-conveyor installations of any significant size. Of these mines, three are in the Crystal Falls-Iron River district of Michigan on the Menominee Range, one is on the Marquette Range near Ishpeming, Mich., and one is on the Mesabi Range near Keewatin, Minn.Results of the studies of tackless haulage in the Lake Superior district will not permit the establishment of any formula to prove or disprove the advantages of belt or shaker systems at all underground mines. The studies do show that trackless haulage can be used to advantage where the proper conditions exist. Advantages are particularly apparent when development can be planned sufficiently in advance of exploitation to permit installation of belts or shakers as part of the development program and where the systems are extended to include haulage in stopes as well as main entries.During the winter of 1947-48, the Bureau undertook a study of all of the underground ore conveying systems known to be in operation in the Lake Superior district for the purpose of making available to the entire mining industry the technologic data developed in the area. Because conditions that led to the installation of the belt and shaker conveying systems were often a function of the character of the deposit or the method of mining, a brief description of those conditions is included in this report.After a preliminary investigation into the extent to which trackless conveyors were employed in the district, it was found that a detailed study at five bites would result in fair appraisal of that method of haulage in the underground iron-ore mines.Each of the five significant installations is described separately in this report. In one instance, however, company policy does not permit identification of the mine wherein the conveying is done. In that instance the operation is designated as mine ""A"".Unless otherwise specified, all tonnage figures quoted herein are gross.The cooperation of officials of all of the companies operating underground mines in the Lake Superior district permitted successful completion of preliminary studies of mining practices and conveying systems.Special acknowledgment is made to R. D. Satterley, general superintendent, and to operating staffs of the Sherwood and Morris mines of the Inland Steel Co. The assistance given by W. D. Whitman, assistant superintendent, and Douglas Tippett, mine captain at the Morris mine, and P. D. Pearson, superintendent, R. O. Marsten, engineer, and W. Johnson, mine captain, at the Sherwood mine, is acknowledged."

Oct 1, 1949

By R. Lusignea

A device has been developed for nondestructive testing the holding power of split tube friction rock supports. It operates by measuring the amount of decrease in internal volume when the support is forced into the drilled hole. The pullout force or slip load is a function of this decrease in volume. The device gives readouts of the average internal diameter and predicted pullout force or the support. Laboratory and field tests showed excellent repeatability and good correlation between predicted and actual pullout force. The device is hand-operated, lightweight (7.5 lb) and can be used on any friction support.

Jan 1, 1983

By William R. Wayment, David E. Nicholson

A modified percolation - rate test is proposed for use in determining flow rates through hydraulic backfill ; in contrast to the conventional test , a percolation- rate versus void - ratio relationship is established . requirements and a detailed test procedure are described . Equipment Results of a conventional test are compared with those of the proposed modified test . The proposed modified test method yields more accurate , realistic , and usable percolation- rate ( permeability ) data . The significance of obtaining accurate percolation rates for use in analyzing waterflow through hydraulic backfill is discussed .

Jan 1, 1964

By Thomas Gales

Longwall mining of thin shallow coal seams utilizing open pits is technically feasible. The thinnest coal seam which can be mined using available technology is 34 inches. The capital expenditure for a 1,000,000 ton per year operation is $15,494,000, and the projected rate of return is 5 percent. Similar statistics for a conventional area surface mine are S18,937,000 capital and 14 percent rate of return. The longwall surface mining method disturbs 63 acres of land per 1,000,000 tons, and the conventional area surface mine disturbs 198 acres A significant bibliography of the technology involved is included.

Jan 1, 1976

Rapidly identify unstable mine waste embankments and similar dam structures. Approach Aerial photography, geotechnical instrumentation, and telephone or satellite data transmission are used to supplement walk-around inspect ions. How It Works Embankment stability and other indicators of structural integrity are evaluated using aerial photography, and on-site unattended instruments and data transmitting systems. Evidence of external movement and water seepage is obtained from aerial photography and photogrammetric evaluation techniques. Surface points marked by stake- mounted targets are monitored photographically at time intervals of several weeks or months. Photographic measurements of x, y, and z coordinates of these points are obtained from flying a series of photo-runs over the dam.

Jan 1, 1979

By S. J. Pearce

One phase of the work of the Bureau of Mines in health and safety is promotion of the use of safe, satisfactory, and reliable respiratory-protective devices. To insure that such devices will be available, the Bureau has established schedules of minimum requirements for self-contained breathing apparatus,3/ gas masks,4/ supplied-air respirators (hose masks, air-line respirators, and abrasive-blasting helmets, hoods, or masks),5/ dispersoid (dust, fume, and mist) respirators,6/ and nonemergency gas respirators (chemical-cartridge respirators).7/ Approval tests of self-contained breathing apparatus are conducted under the supervision of mining engineers of the Accident Prevention and Health Division} Region VIII; approval tests of other types of respiratory-protective devices are conducted by the Health Branch.

Jan 1, 1952

By G. R. Hopkins

For several years prior to about the middle of 1928 both the number and capacity of natural-gasoline plants showed a steady increase; this resulted from a material gain in the supply of casinghead has due to the discovery of a number of flush fields with relatively high gas-oil ratios. From 1928 to date some form of proration has been continually in force, with a consequent curtailment in the supply of wet gas. This decline in available gas and a severe decrease in prices, due largely to the increasing competition of light refinery products, has eliminated virtually all of the weaker units during the last 5 years, with the result that the number of plants declined from 1,155 on January 1, 1928 to 19035 on January 1, 1930, to 909 on January 1, 1932, and then to 859 on January 1, 1934, The struggle of the small high-cost producers to exist is illustrated further by the trend in the number of shut-down plants, which has increased from 36 on January 1, 1930 to 100 on January 1, 1932 and to 128 on January 1, 1934. The increase in the number of plants prior to 1929 resulted in a material gain in the total capacity, but the decline in number between 1929 and 1932 was not followed by a corresponding decrease in capacity, as gains resulting from the construction of a few very large plants overbalanced the loss due to the dismantling of a large number of small ones. However, the low prices of 1932 and 1933 supplied little incentive for new construction, and the total capacity declined in approximately the same ratio as the number. Thus the total capacity declined from 11,387,000 gallons daily on January 1, 1932 to 13,060,000 gallons daily on January 1, 1934, Of the latter 9,181,000 gallons (91 percent) represented the capacity of the operating plants and 679,000 gallons (9 percent) the capacity of the idle plants.

Jan 1, 1934

By W. T. Wertman

LABORATORY research has been started at the Bureau of Mines Morgantown Petroleum Research Laboratory, Morgantown, Va., to investigate the possibilities thermal-recovery methods for producing crude oils of high API gravity found in oil reservoirs of the eastern United States. This bibliography on thermal methods of oil recovery was compiled as a part of the work. Crude oil discoveries to December 31, 1958, in the United States were estimated to exceed 270 billion barrels. Cumulative production of crude oil through 19.55 was about 60 billion barrels, and the American Petroleum Institute estimates that an additional 30.5 billion barrels are economically recoverable by present methods. On this basis, about two-thirds of the oil that has already been found can be classified as economically unrecoverable for lack of a satisfactory method. The rap icily rising costs of proving new deposit; of domestic petroleum, the lack of new discoveries of large oilfields in the united States, and I he growing demand for crude oil have caused an acceleration of research to develop new or improved methods fur producing "unrecoverable" oil in known reservoirs.

Jan 1, 1960

By R. D. Leitch

"The pollution of streams has received much attention during the last few years, and although there are many other and more serious forms of pollution, the problem of acid mine drainage is important in certain sections of the country, particularly in Pennsylvania. At the request of the United States Public Health Service the Bureau of Mines undertook to determine some of the factors contributing to formation of acid mine waters, the yearly variations in quantity and quality of drainage, effect of mining methods, and various other questions arising in connection with the problem; some attention was also given to its economic phases.In acknowledgment, the writer wishes to thank Dr. R. R. Sayers, Chief surgeon; A. C. Fieldner, chief chemist; and W. P. Yant, supervising chemist, health laboratory section of the Pittsburgh Experiment Station, all of the Bureau of Mines, under whose direction the work was conducted.Because no data of a like nature had previously been determined, and with the thought that such data would throw additional light on the general subject, a stream having a number of mines draining into it was selected for observation in both high-sulphur and low-sulphur bituminous-coal districts, as designated in commercial rating. These mines and streams were visited in both wet and dry seasons to note the quantity and variations in acidity of mine drainage and the subsequent effect on streams. Maps of these streams with the sampling points are shown in Figures 1 and 2. In a report of this nature a great deal of tabular data is best emitted, but reference to the maps will serve to indicate the factors that determined sampling points, such as tributary streams and gobs."

Sep 1, 1928

By Robert S. Warfield

Eight samples of high-volatile bituminous coal, each large enough for a study of its coking properties by the Bureau of Mines, were obtained from a location along the Kukpowruk River, Arctic Northwestern Alaska. Bench scale and pilot plant carbonization studies with several patterns of coal blending were conducted. The data from these tests were compared to data from similar tests on a coking blend used by the Kaiser Steel Corporation at Fontana, Calif. The majority of the samples representing the 20-foot seam was found to have significant coking properties, and produced coke approaching metallurgical quality when blended with selected coking coals. Although oxidation effects were evident in the samples representing upper portions of the seam, it appears that the whole seam could be used.

Jan 1, 1966

By Ludwig Schmidt

The policy of buying crude oil on a gravity basis , recently instituted by the major crude oil purchasing agencies in the Mid- Continent field , has caused a new and vital interest to be taken in the work of the U. S. Bureau of Mines for preventing evaporation of crude . From the early years of the industry oil men have recognized that the gravity of crude oil is usually an index of the gasoline content , but it has not been so generally known that the gravity of the crude oil decreases if evaporation is permitted . In 1919 the Bureau of Mines began a survey to determine the evaporation losses of crude petroleum in its various stages of handling from the well to the refinery , The results of this study are presented in Bulletin 200 ( Wiggins , J.H. , Evaporation losses of petroleum in the Mid- Continent Field , Bulletin 200 , U. s . Bureau of Mines , 1922. ) and Bulletin 225 ( Wiggins , J.H. , Methods of decreasing evaporation losses of petroleum , Bulletin 225 , U. S. Bureau of Mines , ( In press ) The findings of this survey were so startling that soon after the preliminary report had been published , several tank companies began manufacturing vapor- tight tanks for the purpose of reducing these important losses . Since that time the development of this type of apparatus has been so rapid that today , every oil trade journal carries numerous advertisements of vapor- tight tanks and equipment as well as technical articles dealing with various problems in connection with the elimination of evaporation losses , whereas three or four years ago the subject was scarcely even thought of. The present report has been prepared in response to numerous requests for information on the apparatus actually being used to prevent evaporation losses . At this time oil operators are also extremely interested in holding the lighter fractions in the crude oil in order to prevent a lowering in gravity . The practice of removing the vapors from crude- oil tanks by means of a slight vacuum and extracting the gasoline from them is not discussed here .

Feb 1, 1923

By John L. Edwards, Anthony T. Iannacchione

There has been a persistent need to forecast roof falls so that miner’s exposure to hazardous underground environments can be minimized. Several monitoring techniques have been developed and are used today with varying levels of acceptance in the mining industry. This paper examines the potential for monitoring microseismic emissions activity as a means of forecasting roof falls. The use of this activity to forecast roof falls has drawn only limited attention, resulting in a lack of published field performance data. This deficiency is being partially addressed by analyzing data obtained during longwall mining at Moonee Colliery in 1998. The Moonee data base contains a wealth of information concerning roof fall forecast parameters and the seismic alarm criteria used to develop these forecasts. Four seismic alarm criteria were developed and used by Moonee with varying degrees of success. Roof falls were forecasted 73% of the time with average forecast times of 54 minutes. Ninety percent of the predicted roof falls had a warning time, i.e., the time between warning and roof fall event, of greater than 1 minute. The fraction of forecasted roof falls decayed logarithmically as a function of warning time, until only 20% of events were predicted more than 100 minutes prior to roof falls. False alarms occurred in 50% of the warnings. Many of the false alarms were quickly followed by a cessation in mining which could have temporarily halted the on-going failure process. If mining had continued immediately after the false alarms, a roof fall may have occurred soon after. The microseismic activity collected from Moonee Colliery demonstrates that techniques to forecast roof rock instabilities in underground mines are possible.

By W. A. Calhoun, M. M. Fine

"One of the most important wartime activities of the Bureau of Mines was the search for new sources of mineral necessary to the prosecution of the war. Part of that effort was in the form of metallurgical service extended to other government agencies engaged in purchasing and stock piling some of the more critical and strategic materials.Fluorite was one of the materials stock piled by the Metals Reserve Company. The fluorite was usually in the form of coarse metallurgical con¬centrate purchased in the United States and abroad. The material was stock¬piled to insure an adequate reserve of fluorite for the metallurgical industries. The domestic production of metallurgical fluorite containing a minimum effective calcium fluoride content of 55 percent,4/ however, gradually increased until production was at least equal to consumption. The stock-piled metallurgical fluorite, therefore, soon became a surplus commodity.On the other hand, the supply of acid-grade fluorite, containing a minimum of 97.5 percent calcium fluoride and n maximum of 1.5 percent silica,5/ was never entirely adequate. Increased consumption of acid-grade material in the aluminum, petroleum, and chemical industries kept that material on the critical list during the war.Under the circumstances, it was felt that a study of the possibility of producing acid-grade fluorite from the metallurgical stock piles would be of some benefit to the war effort. Consequently, samples of fluorite from several of the Metals Reserve Company stock piles were tested by the Bureau of Mines at the request of the War Production Board.Two groups of samples were submitted for testing. One consisted of metallurgical fluorite purchased from Mexico and stock-piled in the El Paso and Laredo, Texas, stock piles of the Metals Reserve Company. The second group of samples was from the stock piles at Gila, N. Mex.The sample submitted from the El Paso stock pile consisted of about 5,000 pounds of minus 4-inch material. Mineralogically, the sample consisted of fluorite contaminated by calcite, chert, quartz, and small amounts of iron and alumina. Although some of the fluorite was reasonably free from gangue at minus 1-inch, much of it remained locked in sizes as fine as 65-mesh.The Laredo sample was about 5,000 pounds of material from five different piles. The samples from each stock pile, A to E, inclusive, were analyzed separately to determine whether the grade of the material in the piles varied markedly. As there was little difference in the analyses, the samples were combined in proportion to the tonnage represented to make a composite sample for testing. The composite sample consisted of fluorite with small amounts of quartz, calcite, and barite. Most of the fluorite was the dark-colored, opaque variety. A small amount of iron-oxide staining was present, and traces of muscovite, clay, pyrite, and tourmaline were noted. The quartz was present as crystals in vugs, and as finely disseminated grains in the fluorite. The druzy quartz and the calcite were free at minus 10-mesh, but the disseminated grains, some of which were 1 to 15 microns in size, were not entirely free at minus 270-mesh. A petrographic estimate indicated that 65 percent of the silica was locked in the 150- to 200-mesh."

Jun 1, 1946

By Christopher Mark, Gregory M. Molinda, Timothy M. Barton

The Coal Mine Roof Rating (CMRR) was first presented at this Conference nine years ago. Since its introduction, the CMRR has been incorporated into many aspects of mine planning, including longwall pillar design, roof support selection, feasibility studies, and extended cut evaluation. It has also become truly international, with involvement in mine designs and funded research projects in South Africa, Canada, and Australia. The purpose of this paper is to bring the mining community up to date with recent improvements and applications of the CMRR. The most important new development is a streamlined process for determining the CMRR from exploratory drill core. Just three types of information are now required: •Fracture spacing (or RQD) •Uniaxial compressive strength (or axial Point Load Testing) •Diametral Point Load Testing The moisture sensitivity adjustment has also been changed, and new research has related the immersion test to slake durability. Most recently, the CMRR has been implemented in a computer program, which can be obtained from NIOSH free of charge. The program facilitates calculation of the CMRR from either underground or drill core data. Values from many locations can be saved in a single file, and an interface with Autocad allows CMRR contour plots to be integrated into mine planning.