Search Documents

By J. P. Capp

This experiment, one of a series on underground gasification of coal, was an investigation by the Federal Bureau of Mines of hydraulic fracturing as a means of increasing the air acceptance of a coalbed to permit introducing combustion air and removing product gases. Specific objectives of the investigation included: (1) Fracturing a coalbed; (2) determining the distance the coal was physically affected; (3) ascertaining the effect of the fracture on air acceptance of the coalbed; and (4) gasifying the coal. The coal was fractured with a fluid consisting of 15,000 lb. of sand mixed with 10,000 gal. of fuel oil and 5,000 gal. of kerosine, injected at pressures up to 900 p.s.i.g. and rates up to 425 g.p.m. The oil served as the fracturing medium, and the sand as a propping agent to hold the fracture open. From the fracture point, (the place in the bed where the fluid was injected), the fracture extended 200 ft. or more along the face cleats, somewhat less along the butt. cleats, and was confined to the coalbed. At the fracture point, the bed accepted about 500 std. c.f.m. of air, which was an etghtyfold increase. Fracture effects were extensive, as airflow was noted from old mine workings and outcrops 600 to 800 ft. from the fracture point. It is probable the actual fracture was much less than 600 ft. and that normal coalbed permeability beyond the fracture limits was responsible for this flow. This indicated that effects of the fracture extended beyond the area of coal physically affected. Although no attempt was made to gasify coal more than 200 ft. away, these effects plus the natural permeability of the bed likely would permit combustion beyond the outer limit of the fracture. As these experiments continued for more than 2 years, and greater air acceptance due to the fracture was observed at the beginning of each test, it is apparent that the effects of the fracturing persist for a considerable time.

Jan 1, 1960

By John B. Goodman

This report summarizes the work done by the Koppers Company, Incorporated, in cooperation with the Bureau of Mines on the commercial evaluation of the primary low-temperature tars produced from Texas lignite in the Rockdale, Tex., plant of the Aluminum Company of America in conjunction with the Texas Power and Light Company. The interest of the Bureau of Mines in this project is twofold. First, through its cooperative agreement with the Texas Power and Light Company the Bureau has assisted in the technical design and practical operation of the prototype, externally heated, entrained-state carbonizer for producing char for electric-power production and for primary low-temperature tar. Second, the first successful operation of the prototype carbonizers employing the Bureau of Mines-Parry process on lignitic coal in 1953-54 led to the production of large quantities of primary lignitic tar, concerning which too little was known or had heretofore been published in this country.

Jan 1, 1959

By S. M. Dar

The U.S. Bureau of Mines constructed a full-scale model of a 15-ft-wide coal mine entry to use in combination with finite-element analyses to investigate roof support systems and various types of roof bolts. The objective was to enhance understanding of the fundamental mechanics of the interaction between rock and supports and the relative integrity of bolted mine roof as a function of roof bolt type, length, spacing, and tension, and the basic characteristics of the roof strata. The laboratory test results, when correlated with computer simulations using fmite-element analysis and underground verification tests, should provide a basis for desigillng safer, more cost-effective roof control systems and help to establish guidelines for employing fully grouted resin and mechanically anchored bolting systems. The background for this research, the research approach, the methods and equipment employed, and the results are described in this report.

Jan 1, 1989

Research workers from the Bureau of Mines and industry met with other government and industry representatives at the Mont Chateau Lodge, Morgantown, W. Va., on May 30-31, 1973, to discuss the current status of methane control in eastern U.S. coal mines. The opening remarks, the eight technical presentations, and the discussions of the members of a government-industry panel are published here for the benefit of those concerned with the control of methane in coal mines. In addition, an introduction has been added to present the background of work in this field.

Jan 1, 1973

By Joseph F. Davies

To gain knowledge of the actual accident hazards present in Kentucky coal mines, reports of fatalities during 1931, 1932, and 1933 have been analyzed and the pertinent factors included in tables, accompanied by some discussion and recommendations for the reduction of accidents from particular causes. ACKNOWLEDGMENT This study was made possible through the cooperation of John F. Daniel, chief of the Kentucky Department of Mines, who made available department records, in addition to the monthly bulletine issued by his office reporting these fatalities.

Jan 1, 1934

By Ralph B. Youtz

This paper describing mining methods at, the Eighty-Five mine of the Calumet and Arizona Mining Co., Valedon, N. Mex., is one of a series being prepared by the United States Bureau of Mines on mining methods, practices, and costs in the various mining districts in the United States. The Eighty-Five mine is in southwestern New Mexico, 3 miles southwest of Lordsburg, Hidalgo County (see fig. 1). The mine produces normally 7,000 to 8,000 tons per. month of silicious copper-gold-silver ore, and employs approximately 200 men underground and 40 on-the surface. Mining is done by shrinkage and cut-and-fill methods.

Jan 1, 1931

By J. Douglas Causey

In 1984, at the request of Bureau of Land Management, the U.S. Bureau of Mines studied the 13,730-acre Burnt Lodge (MT-065-278) Wilderness Study Area (WSA) in order to evaluate the mineral resources. The WSA is located in Phillips and Valley Counties, MT, about 55 miles south of Malta adjoining the Charles M. Russell National Wildlife Refuge. It is underlain by near horizontal sedimentary beds of the Hell Creek Formation, Fox Hills Sandstone, and Bearpaw Shale. No mines or prospects were found in the WSA. Bentonitic beds were examined, but are generally less than 1 ft thick and, except where exposed, are deeply buried. Kaolin-bearing sandstone in the Colgate Member of the Foxhills Sandstone was sampled and may have potential for use in structural clay products. However, remoteness and inaccessibility of the area make it unlikely that the material could be economically extracted even though some of the material is marginally useful.

Jan 1, 1985

By Floyd G. Anderson

This report reviews and summarizes information on prevention and suppression of dust in mining, tunneling, and quarrying published in the United States during the years 1958 through 1960. Unpublished pertinent data developed or assembled by the Bureau of Mines during this period also are included. Silicosis statistics reported by the U.S. Public Health Service indicate a sizable silicotic population in the United States and suggest a need for greater dust-control effort. A joint medical-environmental survey was begun by the U.S. Public Health Service and the Bureau of Mines to evaluate the magnitude of the silicosis problem in the metal mining industry in the United States.

Jan 1, 1962

By William E. Souder

The behavioral accident simulator (BAS) is a computer program that can be used to simulate accident situations. It demonstrates how the potential to have an accident grows or diminishes as a result of changes in various environmental, organizational, and behavioral factors. It calculates the number of fatalities that may result from various conditions and graphically displays these data. The BAS is useful for studying systems of accident causes, for demonstrating the various ways to diminish fatalities, and for training employees. This Bureau of Mines report provides the detailed instructions needed to use the BAS.

Jan 1, 1988

By Gerald T. Homce

A system capable of monitoring mine electrical power systems and detecting impending component .failure could significantly improve power system safety and reduce unscheduled equipment downtime. Such monitoring would require a method of evaluating electrical parameters, calculated from terminal values, for indications of component deterioration. The U.S. Bureau of Mines has targeted electrical failure of squirrel cage induction motors and examined the use of mathematical models to aid in this evaluation. The initial stage of this work is complete, and has produced polynomial networks called adaptive learning networks (ALN's) that can detect and quantify winding insulation leakage simulated on laboratory motors. In this modeling process, empirical data from laboratory motors were used to select the electrical parameters most significant for assessing? motor conditions, and mathematical expressions relating these parameters to simulated deterioration were formed. ALN's developed thus far can process readily measured motor terminal information and quantify power and current levels of laboratory-simulated leakage to within 1% and 3% of full load values, respectively, for motors in the 10-to 150-hp size range. The next stage of this research is validation of these ALN's for actual motor failures; this stage is currently underway, using accelerated life testing of laboratory motors.

Jan 1, 2010

By J. R. Thoenen

[Before 1914 Germany held virtual monopoly on the world supply of potash for fertilizer purposes. During the world War, potash shipments to the United States ceased, and recourse was had to domestic supplies. High war-time prices stimulated interest n various sources, and domestic production increased rapidly. At the close of the war, resumption of shipments from Germany and other sources reduced prices to below pre-war levels, and, as a result, most of the domestic producers ceased operational.]

Jan 1, 1941

By Julius G. Chang

Against the receding background of the October stock market crash and the December overhang of inventories, the economy began with a shaky start in 1988. As 1988 began, the Administration's estimate of real growth for 1988 had just been reduced from 3.5% to 2.4% and economists and other ob-servers were concerned that the expansion that was 5 years old might be near the end and that a recession might be around the corner. The ensuing moderately strong economic activity, however, belied all the negative signals that were evident earlier, and the real GNP continued to grow at an estimated 2.3% annual rate during the first quarter of 1988, extending the ongoing recovery into the sixth year (table 1.). The relatively accommodative policy of the Federal Reserve Board (the discount rate was cut by 0.25% in January), a strong performance by the export sector, and the revival of consumer spending were major forces underlying the economic strength. But as the quarter drew to a close, signs of tight capacity utilizations were apparent in many of the export and capital goods sectors, including textile, chemical, plastic, metal, and machinery. Employment was at a record high level while the unemployment rate was close to a historical low. Prices were rising at a faster pace than those of 1987, and the dollar resumed its slide after a brief recovery in January and February. These factors gave rise to the fears of higher inflation. Long-term interest rates increased, casting a pall over the prospect of a robust growth for the rest of the year.

Jan 1, 1988

By Kenneth M. Maas

The Bureau of Mines inventoried the land in southwestern Alaska to classify ownership and availability and compared this land with known mineral terranes and mineral deposits. This report discusses and quantifies the potential for favorable location of mining claims for metalliferous (locatable) mineral deposits. Of the nearly 24 million acres that constitute the study area, approximately 3.6 million acres or 17% are available for mineral location, 3.4 million acres or 14% are available with restrictions, and 17 million acres or 71% are unavailable. Mineral terranes are known to underlie about 7.8 million acres or 33% of the study area; 3 million acres or 38% occur on land available for mineral location, 1.3 million acres or 17% occur on land available with restrictions, and 3.5 million acres or 45% occur on unavailable land. The State of Alaska has opened over 91 % of its land in the study area to mineral location; in comparison, the Federal Government allows mineral location on 0.07% of the land under its jurisdiction. There are 117 known mineral deposits or occurrences within the study area, including 77 lode deposits and 40 placer deposits. Of the 41 lode deposits occurring within a mineral terrane, 2 occur on available land.

Jan 1, 1988

A concise country-by-country summary of the mineral industry of Africa is presented. Reserves, resources, role of the country in the world mineral supply, and developments in the mineral industries are reviewed. The data on each country are accompanied by a map showing mineral location and transportation facilities.

Jan 1, 1976

By Robert Stefanko

Test procedures for evaluating underground coal mine trailing cable splices are formulated. The tests are utilized to evaluate several trailing cable splices. The laboratory results are compared with actual field observations and experience. The results are utilized to define quantitatively the generalized terms of the 1969 Health and Safety Act. Recommended specifications and procedures for testing by MESA Department of Approval and Testing personnel are included. Failure points in splices are detailed and presented for use by a MESA training program and manufacturers attempting to improve product quality.

Jan 1, 1974

By Suresh K. Bhatt

A mathematically simulated modeling technique is used in this U.S. Bureau of Mines report to represent a hypothetical mining operation with existing mining technology and prevalent mining costs. Mining scenarios were prepared and evaluated for potential benefits and costs available through computer-assisted mining. Base criteria, parameters, and methodology are described.

Jan 1, 1993

By A. E. Petersen

To reduce U.S. dependence on imports of titanium, the U.S. Bureau of Mines has investigated the recovery of titanium from perovskite (CaTi03). Domestic perovskite deposits represent a significant, but untapped, titanium resource. An acid sulfation method was developed that will extract about 97 pct of the titanium and the columbium and 70 to 90 pct of the rare-earth byproducts from perovskite concentrates. A flow-sheet for recovering titanium as pigment-grade titanium dioxide (Ti02) is discussed. Test work performed in developing each unit operation is described. The first three unit operations have been demonstrated using laboratory-scale continuous methods of operation: acid sulfation of perovskite concentrates, leaching sulfation residue to dissolve metal values, and precipitation of titanium oxysulfate monohydrate (TiOS04?HP) from the resulting leach flltrate. Batch testing of other unit operations was performed: TiOS04?H20 redissolution and iron reduction, precipitation of Ti02 by hydrolysis, and regenerating recoverable acid with rare-earth byproduct recovery. Cost evaluation results are provided, indicating that processing perovskite concentrates by acid sulfation may be an economically viable means of producing Ti02.

Jan 1, 2010

By Anthony D. Szpak

The purpose of this program was to demonstrate the feasibility of Illuminating various types of underground coal mining machinery as required by the Federal Coal Mine Illumination Standards Part 75.1719 to 75.1719-4 Code of Federal Regulations Title 30. Nine various machines were illuminated and the illumination systems were evaluated for a 3 month period of operation. Factors evaluated were ease of implementation, reliability, ease of maintenance, acceptance by mine workers and operators, Illumination degradation and durability.

Jan 1, 1981

By Lloyd A. Morley, Alan M. Christman

PART A. ELECTRICAL EQUIPMENT – GENERAL Paragraph 1. Electrical Equipment; Examination. All electric equipment shall be examined, tested, and properly main¬tained by a qualified person to assure safe operating conditions. The examinations and tests shall be performed at intervals not exceeding six (6) months unless otherwise specified in Parts A, B, C, D, and E. When a potentially dangerous condition is found on electric equipment, such equipment shall be removed from service until such condition is corrected. A record of such examinations shall be kept and made available to an authorized representative of the Secretary and to the authorized repre¬sentative of the miners in such mine. Each item of major equipment, in¬cluding substations, switchgear, load centers, and so forth except powered hand tools, shall be recorded separately. The record of such examination shall include all dangerous conditions found, corrective action taken, and name of examiner, and shall be signed by the person responsible for main¬taining the equipment in safe operating condition, who shall also be a qualified person. Paragraph 2. Electrical Work; Qualified Personnel. No electrical work shall be performed on electrical distribution circuits or equipment, except by a qualified person or by a person trained to perform electrical work and to maintain electrical equipment under the direct supervision of a qualified person. Disconnecting devices shall be locked out and prominently tagged by the persons who perform such work, except that in cases where locking out is not possible, such devices shall be opened and prominently tagged by such persons. Locks and tags shall be removed only by the persons who installed them or, if such persons are

Jan 1, 1976

By Oliver C. Ralston

The nonmetallic minerals work of the Bureau of Mines started with the organization of the Mineral Technology Division in 1912. A special experiment station devoted to the mining, preparation, and processing of nonmetallic minerals was established in 1923 at New Brunswick, N. J., and concentration problems on nonmetallic minerals of all kinds also were studied at the Mississippi Valley Experiment Station at Rolla, Mo. In July 1936 the Nonmetals Division was organized, and in May 1937 the Nonmetallic Minerals Experiment Station at New Brunswick, N. J., was moved to and made a part of the new Eastern Experiment Station at College Park, Md. At present the Nonmetals Division operates at three points: The Eastern Experiment Station, College Park, Md., which is headquarters for the division chief; the Southern Experiment Station, Tuscaloosa, Ala.; and the Northwest Experiment Station, Seattle, Wash., where coal washing and preparation studies are included with those on nonmetallic minerals. Sand, gravel, and aggregate work is carried on by the Mining Division, as sand and gravel preparation are intimately associated with mining methods. The Economics Branch of the Bureau of Mines also prepares occasional papers on nonmetallic technologic subjects in connection with the presentation of statistics on a particular industry and reviews of the mineral industry in foreign countries for use in the monthly publication, "Mineral Trade Notes."

Jan 1, 1937