Search Documents

By Francisco Sena Leite, Raquel Sobral, Vinicius Gouveia de Miranda, Céu Jesus

"This document investigates a newly developed technique with the objective of improving terrain triangulation models (horizontal/sub-horizontal and vertical/sub-vertical terrains), mainly blast free faces. The algorithm uses multi-linear regressions to generate the best point cloud projection plane by applying the residues modulus minimization so as to create the finest 3D triangulation model. A change of base is required to create a new set of coordinate axis and generate completely new projection planes. The projection plane residue analysis is inferred in order to avoid or reduce the outlier points. The dataset is composed of 12 terrain models obtained from photogrammetry and a 3D Laser equipment thatgenerates georeferenced cloud points. This new technique is validated by the analysis of the obtainedcritical burden by the improvement of the general aspect view of the terrains and the capacity of outlier’s detection. The result and the quality of the algorithm demonstrates the improvement in the triangulation mesh, reducing errors in the calculation of over/under burden, free face volumes, cavities and, therefore, in the estimations of clearance/safety distances."

Jan 1, 2017

By Andrew Stirling

Quarry operators are under constant scrutiny by individual neighbors and neighborhood associations due to the environmental issues arising from daily quarry operations. Issues range from truck traffic, to dust, to blasting induced vibration and noise. Quarry operators and shot service providers employ best practices to minimize disturbances to neighbors. However, these efforts have been limited by the accuracy and flexibility of conventional initiating systems and design techniques.

Jan 1, 2002

By O. Cermak, F. Degonld

Although 3D fragmentation analysis is a relatively new technology, it is rapidly gaining popularity among mid-sized mining operations and quarries. The results provided by this technology are adequate, but like other picture analytic methods, it mainly focuses on the surface of the muck-pile. These results are incomplete or incorrect as falling rocks and boulders from the stemming zone are constantly influencing the muck-pile surface. This obstacle can be overcome by collecting a large amount of data and analyzing it over time. However, this is not always an ideal solution, as companies prefer to receive results immediately after the blast to make resource allocation decisions, production planning, and plan for the next blast. Over the past year and a half, we have conducted a study on various muck-pile fragmentation analysis results from 3D modeling in Central Europe, comparing the results between the surface and inside of the muck-pile. By analyzing multiple shot results, we were able to determine the percentage difference between the top and inside fragment sizes and calculate the range of correction coefficients for different rock types. Applying these coefficients to a single muck-pile surface fragmentation analysis allows us to determine the actual fragment sizes inside the muck-pile. This enables us to make informed decisions regarding loading, hauling, material mixing, and proper crushing or milling. By overcoming the limitation of surface-based analysis, we can now accurately evaluate blast performance, which leads to better processes optimization and increase efficiency. As 3D fragmentation analysis becomes more widespread, we expect to see even more benefits for the mining and quarrying industry

Jan 1, 2024

By Saeed Karimifard, Saman Nouranian, Shahram Tafazoli, Bahram Sameti, Frank Chu, Caitlin McKinnon, Tetiana Konstantynivska, Glen Turner

Continuing blast optimization is the cornerstone of any mine-to-mill approach, and particle size analysis is a key metric for meeting blast targets to reduce overall energy consumption and operating costs. To ensure the statistical validity of particle size data, it is important to sample material frequently. In most mines and quarries, the blasted material is loaded onto haul trucks and then transferred to the crusher; measuring the particle size of each haul truck load therefore provides an adequate sampling rate. We propose a particle size analysis solution for haul trucks that does not impact current operational workflows. Using artificial intelligence (AI) and 3D imaging technology, our solution reliably localizes and identifies haul trucks as they drive by, then accurately calculates the particle size distribution of the visible material in each truck load. In this paper, we identify the challenges of designing and implementing the proposed solution and explain the strategies we employ to overcome these. We also discuss a method for boulder detection that leverages the existing deep learning architecture to significantly reduce crusher downtime caused by oversized rocks. Finally, we present field data from a trial installation. To evaluate each change made to the blast design, it is necessary to measure the effect on particle size. An accurate particle size analysis solution is therefore the first step towards optimizing blasting practices and reducing energy consumption throughout the comminution circuit.

By P. Lozada

The objective currently demanded from controlled blasting techniques is to minimize damage to the remaining rock mass while protecting the integrity of mine walls and ensuring the quality of the fragmented material for easier extraction. Finding this balance represents one of the three main challenges faced by large open-pit mines. They must achieve mine stability by complying with slope designs while also maintaining good results in terms of fragmentation and equipment productivity. The main constraints are related to unfavorable geological conditions, water presence, limited drilling diameters and available explosive products, as well as managing drilling times and blast scheduling, among others. For slope control, in addition to presplitting, blasting designs generally include buffered rows, drilled with smaller diameters, and loaded with fewer kilograms of explosives than production holes. The objective is to reduce the powder factor (kg/t) to minimize the energetic influence on the walls and attenuate damage. However, this often requires using very short charge lengths compared to the bench height (one-third or less) and reducing the pattern geometry, which increases the number of holes per ton and drilling costs. This traditional technique of reducing powder factor in the buffered rows has the main limitation of not being able to distribute the explosive energy throughout the entire column, leading to fragmentation issues mainly in the steaming area. Measurements conducted by Orica in their operations indicate at least a 30% increase in P80 particle size in the buffer zone associated with this condition. To improve energy distribution, techniques such as decking, or vertically decoupled charges can be employed. However, these techniques cannot be applied under wet conditions, and strict control over implementation quality is required to avoid deviations, which increases loading operational times and resource required. In this sense, the use of less energetic and lower-density explosives is a better alternative. On one hand, they allow for complete charge columns in the buffered rows, ensuring homogeneous fragmentation, and on the other hand, they reduce the energetic influence on the slopes, significantly decreasing vibration levels. With less energy per kilogram of explosive (MJ/kg) and less charge per linear meter (kg/m), it becomes possible to handle higher specific charges and longer explosive columns, providing flexibility in drilling and loading design options without compromising slope stability.

Jan 1, 2024

By L D. Santis, L Wardrip

This paper begins with a summary of the development of the sheathed explosive charge from it's conception by the Bureau of Mines in 1981 through the evaluation of its safety, culminating in revisions to the Code of Federal Regulations (CFR), Title 30, Parts 15 and 75 which provide for its approval as a permissible explosive and safe use in underground coal mines. In 1989, Austin Powder Company decided to market a sheathed charge and proceeded to develop a commercial version which they call the Rock*Buster. The Rock*Buster was tested by the Bureau of Mines and subsequently approved as a permissible sheathed explosive unit by the Mine Safety and Health Administration (MSHA). Marketing of the Rock*Buster began in the Spring of 1990. In May 1990, the Rock*Buster was first used in an underground coal mine, Jim Walter Resources' (JWR) No. 4 Mine in Brookwood, AL. Trials with Austin's units were impressive. Representatives from MSHA, the State of Alabama, JWR, the United Mine Workers, and other local mining companies observed the charge break large boulders on the surface. Later, the charges were used underground to break large rocks from a roof fall that were obstructing ventilation. During its first week on the job, the Rock*Buster reduced the downtime experienced on JWR's longwall sections by quickly taking care of problem roof falls which halt operations.

Jan 1, 1991

By Frank Hirthammer

Since the introduction of the Explosives Track & Trace in Europe in 2014 for manufacturers and 2015 for end-users, a lot has changed in all areas of the supply chain and the use of explosives. The regional associations, manufacturers' organizations, and trade associations have proven that it is possible to overcome a hurdle, that looks almost impossible in the beginning, through consistent cooperation. The paper gives an insight into the problems involved in introducing such a requirement, identifies ways and solutions, and concludes them. When looking at the current situation, the paper describes the process by which a prescribed change in business processes are transforming into a solution that increases productivity, security, and handling.

Feb 1, 2020

By Josee Boudreau

Transport Canada has regulatory requirements that pertain to the transportation of explosives. An important component includes the requirement for an approved Emergency Response Assistance Plan (ERAP). The ERAP may be traced to the recommendations made by Justice Grange following the enquiry into the Mississauga train derailment of December 1979. Justice Grange recommended that any shipper of dangerous goods must have a plan to control any release of dangerous goods in the event of an accident, and that the plan must be submitted to the Minister and approved by the Minister or by an organisation or person designated by the Minister. The right to ship could be withdrawn at any time if the plan is found inadequate either in its conception or in its operation.

Jan 1, 2010

By Frank Hirthammer

Since the introduction of the Explosives Track & Trace in Europe in 2014 for manufacturers and 2015 for end-users, a lot has changed in all areas of the supply chain and the use of explosives. The regional associations, manufacturers' organizations, and trade associations have proven that it is possible to overcome a hurdle, that looks almost impossible in the beginning, through consistent cooperation. The paper gives an insight into the problems involved in introducing such a requirement, identifies ways and solutions, and concludes them. When looking at the current situation, the paper describes the process by which a prescribed change in business processes are transforming into a solution that increases productivity, security, and handling. It shows examples from daily work, in which possibilities for optimization, improved quality assurance, and work facilitation are explained. It presents the resulting potential by comparing process flows, before and after the introduction of Track & Trace solutions. What challenges will we face in the future concerning the use of T&T solutions? Will the tracking of explosives become the norm worldwide? What are future hardware and software developments to be expected? What impact will this have on the global supply chain?

By Andreas Gaich

A new 3D fragmentation analysis method for muck piles is presented. It works with aerial imagery from UAVs (drones) and handles entire muck piles with minimum user intervention.

Feb 1, 2020

By Dominic C, Gregory B. Poole

On December 12, 2018 at 4:14 AM EST, an earthquake registering a 4.4 magnitude on the Richter Scale occurred in central Tennessee. According to a survey posted on the USGS website, this earthquake was felt throughout the southeast and even as far away as Arnold Nebraska. That’s over 900 miles (1,448 kilometers) from the epicenter. We recorded the vibrations from this earthquake on 44 different seismographs that were set up with remote access to continuously monitor vibrations from blasting activities. Having this data gave us an opportunity to compare the vibrations caused by earthquakes and blasting. A simple observation of the amplitudes, frequencies, and durations is enough to notice that vibrations from earthquakes are very different than vibrations caused by blasting in mining and construction

Feb 1, 2020

By John Wright

During June and July 1999 a United States Antarctic Program (USAP) team of three commercial divers and one blaster successMy removed an underwater rock obstruction which interfered with safe docking practices of research vessels that call at Palmer Station - the USAP research facility located on Anvers Island, Palmer Peninsula Area, Antarctica. Ordinarily, such a project might be considered routine. However, certain aspects of the project, particularly those dealing with logistics in a remote corner of the earth, sat3eguards for marine biota, and working underwater in the dark of the austral winter, conspired to make this project interesting. Even more challenging was ensuring the protection of the existing pier - a deeply corroded sheet pile structure backfilled with loose gravel and rock - which lay less than 50 feet away from the target obstruction, not to mention uncertainties at the outset as to the nature of the rock mass forming that obstruction.

Jan 1, 2001

By Claude Cunningham

AEL has been developing electronic detonators continuously since 1986. It launched its first system for opencast mining in 1993, and now has two distinct product lines. The path has not been without great difficulty, but the determination to persevere was always buoyed by the strong encouragement of customers who experienced the transformed blasting results, as well as a clear vision of the enormous intrinsic value of the concept. The path of growth to dominant global supplier is traced through the separate application channels of coal stripping, quarrying, massive mining, opencast mining and narrow reef mining, to the first allelectronic detonator demolition blast in June 2001. Reasons for the slow coming to market of this highly desirable concept, which often coincide with reasons for the demise of various other systems, include the difficulty of safely mating electronics and explosives in a low cost environment; the extreme difficulties of achieving proper connection under mining conditions; the rapid rate of evolution of the technology, and the safety concerns raised by various accidents and incidents along the way. ED.s are now established as the way forward and are set to displace other systems in all serious applications. There is place for both programmable and pre-set delay systems.

Jan 1, 2002

By Andre Koekemoer, Gys Landman

At the moment, electronic initiation is migrating from a position of a specialist niche to that of a more widely applied technology. Ease of use and deployment rate are becoming aspects of greater concern for end users.

Jan 1, 2011

By John Floyd, Maria Rocha, Benjamin Cebrian

Wall control blasting is needed in most metal mining operations in terms of increasing mineral reserves and assuring the safety of the operation. This type of blasting has the goal to achieve a clean, stable rock wall in the shortest distance from a well fragmented, easy to excavate, blasted rock mass. This can be done with a variety of blasting techniques, all of which decrease the explosive energy towards the final wall. Each technique needs to suit the geology: modified production blasting, buffer blasting, pre-split and line drilling of empty holes. Pre-split is the most expensive technique, and allows final steeper bench face angles while modified production blasting is the least expensive but needs wider berms.

Jan 1, 2018

By H P. Rossmanith

This contribution addresses the advanced blasting technology which is based on wave propagation theory and fracture mechanics. The new concept of sonicity and the principle of maximizing sonicity in blasting as well as the energy or work of a blast operation will be introduced. It is shown that - in contrast to common belief – it is not the velocity of detonation which controls the blast but the relationship between velocity of detonation and the wave speeds, in other words, the Mach numbers of the blast operation. Based on numerous practical blasts in Germany, the authors show that, when using wave dynamic concepts, there is a linear relationship between peak particle velocity and the work of a blast operation and this linear relationship is controlled by the sonicity of the blast. Extensions to layered and faulted rock masses are presented. It will become clear that a second change of paradigm is enforced, the first one being the implementation of short time delaying. Again, the acquisition of knowledge in wave progation theory and fracture mechanics becomes mandatory in advanced blasting technology, where the art of blasting is now fully transformed into a science of blasting with little room for methods of trial and error.

Jan 1, 2010

By Paul Worsey, Yasutaka Dote

The choreography of large fireworks displays dictates electric initiation for precise timing. It has been common practice to pre-squib products before transportation for reducing set up time. A number of fatal accidents transferring pre-squibbed product during transportation suggests that there is a problem with impact sensitivity. The aim of this paper is to quantify the impact sensitivity of the various configurations of initiating materials used in display fireworks.

Jan 1, 2009

By Richard Scales, Giles Hellyer, Ian Travers, Dean French, Peter Bellairs

"The Mt Whaleback iron ore mine is located in the Hamersley Province situated about 1OOOkm to thenorth of Perth, the capital city of Western Australia. A small but significant portion of the waste in Mt Whaleback presents problems due to its ability to react with normal commercial bulk explosives resulting in premature detonations, two of which occurred at the mine in 1983 causing great consternation as well as disruption to the mining operation. The techniques and procedures developed to overcome this problem were based on the use of tough durable, acid and heat resistant liners to provide a physical barrier separating the explosive from the rock togetherwith the development of an accurate down the hole remote temperature logging technology. The liner technology was developed due to the inability to produce a reliable inhibited ANFO despite exhaustive mine based testwork."

Jan 1, 1999

By Valeri Mitkov

Studena Quarry is one of the main suppliers of inert materials for concretes production in Sofia. It is characterized by massif heterogeneity in density and fissuration. Failure to take into consideration this fact during the planning of the blasting works recently had unsatisfying results in their carrying out – obtaining of materials with too small dimensions or high percentage of outsize material. Series of test blasting were carried out to find the relations for calculation of the main parameters of the drilling and blasting works. The blasting network was enlarged to 6 x 6 m, the diameter of the shot-boreholes was changed from 110 to 152 mm, the stem of the boreholes was significantly reduced and the relative consumption of blasting agents as a whole was reduced to 0,37 ?g/m3.

Jan 1, 2010

By Benjamin Cebrian

Rock blasting at quarries represents multiple challenges not easy to see at first sight. Aggregate industries face similar or superior prices for explosives while extracting a material that usually is of less value of metal mining operations. Therefore, learning to optimize a quarry operation can be a perfect training for a position in blasting at larger metal mining operations.

Jan 1, 2010