Search Documents

By Alex Chapman, Cam Thomas, Bryan Karney

"During the early summer of 1989, Ontario Hydro removed a concrete portion of the North Channel Dam at Crystal Falls Generating Station by blasting and excavating in marine conditions. Because of the severity of underwater blasting and because the site was in close proximity to the replacement dam, there was concern that hydraulic shock waves generated by the detonation could damage either the new dam or its control structures. This paper examines the data associated with the hydraulic shock waves generated by underwater blasting, and studies the effectiveness of an air curtain in reducing the peak pressures. In previous trials using the air curtain technique, a rule-of-thumb factor was used to estimate that only 10% of the original pressure pulse would propagate across the air curtain. However, this value had little basis in theory. A theoretical formulation of the problem by Karney in 1989 indicated a provisional value of 0.18 for this factor, but was heavily dependent on confirmation from in-field testing. Data provided by Ontario Hydro from an actual blasting procedure indicate that a more conservative value of 0.32 may be more appropriate. Thus.although the air curtain did provide considerable reduction of peak pressures, the data at Crystal Falls indicates its performance was below the anticipated level. However, due to problems with the instrumentation and some inconsistencies in the resulting data. it is recommended that this value be further refined as additional data become available."

Jan 1, 1992

By L C. Taylor

Both the U. S. Navy and the U. S. Army are interested in knowing more about the loading applied to vehicles which are unfortunate enough to encounter a detonation of a buried mine in the course of performing their normal duties. The Dynamic Effects Laboratory at the University of Maryland has been involved in small scale testing for ten years to assist the Navy and the Army in understanding the loads that are applied to personnel carriers when a buried explosive detonates beneath them. This paper describes results from small scale tests conducted to determine the loading mechanisms on target plates when subjected to loading due to the detonation of a buried mine in saturated sand, dry sand, and water. Transparent target plates were utilized in order to determine the loading process beneath a floor board on armored vehicles. Various charge sizes were scaled in the laboratory accordingly to a standardized full size threat encountered in the battlefield. Tests were conducted in saturated sand, dry sand, and water keeping the stand-off distance of the target and the depth of burial of the charge constant. In the case of water impacting a transparent PMMA plate the crack propagation was recorded and the crack velocity is determined. Additional tests were performed in saturated sand by varying the stand-off distance of the target but keeping the depth of burial of the charge constant. The small-scale test results could be scaled to full scale by using verified scaling laws.

Jan 1, 2016

By John Babcock, Bryan C. Smith

In a partnership between Luck Stone Corporation and Loudoun Water, a 42” (1.067m) steel pipeline was constructed along the perimeter of an extensive permitted reserve of diabase rock Luck Stone was about to begin mining. Loudoun Water provides drinking water and wastewater services to over 75,000 households in Loudoun County, Virginia. In discussions to establish the 30-foot (9.1 meter) easement for Loudoun Water within the permitted reserve of diabase rock, Luck Stone and Loudoun Water agreed on the following basic conditions: • Luck Stone could execute production blasting as close to the easement as physical conditions of overburden depth permits. We estimated the minimum distance to be about 75-feet (22.86 meters) from the centerline of the pipe. • Loudoun Water would install strain gauges on the pipe every 500-feet (152.4 m) along the entire length of the future reserve area. This resulted in the installation of 18 strain gauges. • Luck Stone would contract a third-party vibration monitoring company, agreed to by Loudoun Water, to monitor the strain gauges and provide seismograph reading at appropriate locations along the pipe as mining progresses. All information would be provided to Loudoun Water. • Luck Stone’s blasting will be conducted in a manner that ensures the recommended strains are not exceeded.

Jan 1, 2019

By Richard E. Danell

"There are a variety of approaches for wall control blasting in open pit mining operations. Safety forworking in the pit is the principal benefit. There are also a number of economic and productivitybenefits when appropriate techniques are used. The purpose and requirements of wall control blasting can vary quite significantly for different operations. When considering blast design, geology, geotechnical factors, drilling, explosives, economics and blasting history are all part of the engineering design process. In many operations, there is a high reliance on blasting history and economics for determining wall control blasting measures. This presentation outlines approaches that broaden the design process and discusses their advantages."

Jan 1, 1997

By R. F. Favreau, Patrice Favreau

"A blast with explosives creates vibration waves in the zone around the blast.The prediction of the intensity of vibrations is important because people in the cinity demand that the vibrations do not disturb them, and society imposes limits on the vibrations. The U. S. Bureau of Mines (USBM) showed that the easurement of the particle velocity U predicts the risk of damage from vibrations. A currentapproach of blasters to monitor vibrations is to measure them with a seismograph at several distances S, and create a graph of U vs. S and the explosive charge “W” according to the equation U = K / (S / W)N where K and N are constants that depend on the blast method and the nature of the ground over the distance S. Though useful, this equation is empirical, and the results predicted from it are very variable, as shown by figure 1 which indicates that a prediction of U can deviate significantly from the actual value. Moreover, a minimum of two seismograph measurements at two values of S are required to establish the curve. However, here now exists another very convenient method to predict U; it is with the simulator Vibmas, which is based on the fundamental principles of how a blast reates vibrations. This simulator takes into account not only W but rather all the blast parameters, the type of explosive and the properties of the rock. Moreover, to establish the calculation of U as a function of S, only one seismograph measurement is required rather than two as for the USBM method. This last difference is important because it makes it easy to predict U not only as a function of S, but also as a function of the orientation of S. On the site this allows much safer control of the vibrations, and the use of larger explosive charges which reduce excavation costs. The article presents results from a field case at a hydroelectric project in Canada, where the deviation was very moderate. Use of this vibration simulator on the Web is very easy."

Jan 1, 2015

By Junya Tokita

In Japan, packaged explosives have traditionally been used as the most common explosive for tunneling. Recently, some blasting systems such as ANFO with a kettle loader and emulsion explosives with a pump loader have been trialed in order to improve safety and efficiency of the charging process. There are issues with these systems relative to the Japanese market. ANFO dissolves in water easily, and generates ammonia gas when it contacts with concrete. Emulsion explosives need costly pump ing unit s, and there is a need to control residuals in the pump unit. Additionally, there are obstacles by Japanese law to site mixing of emulsion explosives.

Jan 1, 2005

By Randall M. Wheeler

"Fourier analysis is a very powerful frequency analysis tool. However, it is frequently misunderstood and sometimes used inappropriately. Part of this workshop will involve the basics of Fourier series, the Fourier integral and finally the Fourier transform. Included will be a brief discussion of analysiswindows, including the box and Hamring windows."

Jan 1, 1998

By P D. Katsabanis

According to Persson(1) steady state detonation along a cylindrical charge can be regarded as a self propagating process in which the axial compressive effect of the shock front discontinuity changes the state of the explosive so that exothermic reaction sets in with the requisite velocity.

Jan 1, 1990

By Marwan M. Mohammed, Hani S. Mitri, Wilfrid Comeaul, Baoyao Tang

In many parts of the world, rockbursts have become a major problem of mining at depth. As orebodies are being mined deeper, rockburst phenomena have become familiar to deep hard rock mines. Rockbursts are generally characterised by sudden release of energy in a volume of highly stressed rock, which can cause local violent failure of the rock mass around the opening. One method of controlling these failures is to precondition the rock mass by detonating fully confined explosive charges at the appropriate locations. This method known as destress blasting, was first tried in the deep South African gold mines (Roux et al., 1957), and was widely used later in Canada, United States, France, Poland and Japan.

Jan 1, 1999

By Mattos J. L. C

Drilling and blasting with explosives in mining operations near communities require careful planning to mitigate socio-environmental impacts. Ground vibration, noise emission, flyrock, and dust dispersion are factors that may trigger conflicts with local populations. However, large-scale operations demand high productivity and intense material handling, making it essential to balance operational performance with impact control. The adoption of best practices, combined with advanced monitoring and mitigation technologies, enables sustainable mining even in proximity to inhabited areas. This study proposes the use of double and triple-deck blasting techniques with large-diameter boreholes (12 ¼” – 311 mm), addressing the sizing of charges and decks, as well as measures aimed at reducing noise perceived by nearby communities. The approach seeks to maintain the use of large drilling rigs already present in the operation, avoiding costs related to premature equipment replacement or expensive alternatives, while minimizing environmental and social impacts and promoting a more balanced and responsible mining model.

Jan 26, 2026

By Gene Baker

A new Safety Library Publication (SLP), SLP-27, which is titled “Security in Manufacturing, Transportation, Storage and Use of Commercial Explosives” was recently released by the Institute of Makers of Explosives (IME). SLP-27 makes recommendations for both general security and enhanced security at explosives sites when security risk levels, declared by the Department of Homeland Security (DHS) using its Advisory System, have temporarily increased.

Jan 1, 2006

By Gary Cavanough, Stuart Addinell, Hector Parra

Drilling deep, straight, accurate holes in hard rock to achieve efficient blasting is a challenge for the mining/quarrying industries with short holes normally drilled using “top hole hammer” (THH) and deep holes using “down the hole Hammer” (DTH).

Jan 1, 2013

By Tamara Whitaker, James Gunderson, Ruilin Yang

This paper presents the results of a vibration control project conducted in soft overburden at a surface coal mine located in the western United States. The study uses near-field blast vibration monitoring, analysis and modeling techniques developed in house. Accelerometer-equipped seismographs were utilized for near-field vibration monitoring and analysis. Vibration control was achieved through field data regression as well as vibration modeling using the multiple seed near-field blast vibration model (Yang and Scovira, 2007). The regression was conducted between peak particle vibration parameters and the minimum scaled distance per delay. From the regression analysis, the curves of upper bounds for peak particle vibration parameters and charge weight were developed. The dominant frequencies of the blast vibration were also addressed in this project. The regression curves and near-field vibration model guided the blast design to control blast vibration for maximizing the recovery of coal and maintaining mine productivity.

Jan 1, 2008

By John Babcock, Gregory Poole, Ron Hudson

In January 2007, Fultondale Alabama opened a new elementary school. Site work at the old school location included blasting activities and the old school building was scheduled for demolition. With help from Apache Construction, blasting was scheduled to be performed in close proximity to the old school building prior to the demolition. Arrangements were made to perform extensive monitoring on the old school building during the blasting activities. The monitoring plan for the project included: • Pre and post blast inspections were performed on the structure; • Conventional crack monitors were installed at 22 locations throughout the structure; • Digital displacement monitors were installed at 6 locations on the structure; and • Seismographs were used to monitor structure vibration at 6 locations and ground vibrations at 9 locations. Blasting activities were allowed to produce vibration levels well above the safe levels established by the U.S. Bureau of Mines (USBM). Vibration levels up to 7.44 in/sec were recorded with no damage noted. Permanent deformation was recorded on vibration levels of 9.68 and above. Not only did this project reinforce previous studies which indicate that concrete block walls can withstand vibration levels well above 2.0 in/sec, this study was also a good example of employing new technology to help determine if/when damage occurs on a specific structure.

Jan 1, 2009

By Joseph Nawrocki, Margaret Hettinger, Dr. Catherine Johnson

"Optimized rock fragmentation is essential for minimizing downstream costs to mining operations.Photographic fragmentation analysis, vibration monitoring, and high-speed video all providemeasurements of blast effectiveness and supply data that allows operations to modify blasts to achieve downstream goals."

Jan 1, 2016

Choosing the correct delay time for many blasting applications is an important and critical blast design parameter for controlling fragmentation, muckpile shape, swell, digability, throw, ground vibration and airblast. BAl and its affiliates have monitored thousands of full scale blasts in a variety of field conditions, spanning over 15 countries, with sophisticated blast monitoring instrumentation. In some blast environments, a small change in the choice of delay times used had a dramatic and pronounced effect on the overall blast results. In other blast environments, large changes in the choice of delays used had absolutely no effect on the final results in terms of specific outputs. In environments which were sensitive to the delay selection, the type of explosive, dynamic response time of the rock mass (TMIN), integrity of the material, burden and rock mass geometry, all played a very important ,role.

Jan 1, 1998

By Paul Kunze

For some of us, the most disagreeable part of being the blaster- in - charge is doing the required paperwork. Cost coding on time cards, drilling reports, magazine inventory logs, and blast records all eat into our time. When all goes well, which I suppose is 98% of the time, the blast records are submitted and filed, probably never to be seen again. Sometimes a progressive operation will use the information documented in the blast reports to evaluate blasting effectiveness and improve results. When the report is consistently used in this fashion, costs can be reduced and other efficiencies will be realized. A blast report in times past was a simple form that mainly was used to keep track of the drill footage and of the powder used in the shot. However, as the population and consequences of careless blasting increase, multiple levels of blast documentation are now being required nearly everywhere, during all phases of the drill and blast process. We are now compelled to create preliminary blast designs prior to commencing work. We are required to submit pre-blast plans before each shot, and we need to generate post-blast reports that document the details and results of each shot.

Jan 1, 2004

By Randy Martin, Jessie Bonner, Peter Boyd, Mark Leidig, Timothy Rath

We conducted the Vermont Damage Experiment in central Vermont during July 2008. Five single-hole explosions with yields ranging from 60.8 kg (134 lbs) to 122.5 kg (270 lbs) were detonated in homogeneous, low fracture density granite. The goal of the experiment was to quantify the different levels of rock damage around the source and then relate the seismic wave generation to the degree and distribution of damage and fragmentation. In addition, explosives with different velocities of detonation (VOD), including black powder (0.53 km/sec; 1737 ft/sec), heavy ANFO (4.8 km/sec; 15734 ft/sec), and COMP B (8.1 km/sec; 26574 ft/sec) were detonated to relate the VOD to seismic wave generation and extent of damage zones in the source region. Over 120 seismic stations were deployed to record the explosions at distances between 5 m and 30 km (15 ft to 19 miles).

Jan 1, 2010

By Riaan Van Wyk, Gys Landman

In today’s mining environment the use of radio communications in the form of two-way radios, cellular phones and even automated mining, form a vital part of the daily operations of a mining site. The radio transmissions that are used are a form of energy and as with all other types of energy it can have an influence on blasting equipment.

Jan 1, 2011

The objective in control blasting is to reduce overbreak to control the final pit wall slope, shaft, drift, ditch, bench, etc. to the final planned excavation limit.

Jan 1, 1990