Search Documents

By Dirk van Zyl

Rock fabric information is often available from drill hole information and bench face mapping. An approach is presented to predict fragment size distribution of blasted material from this information as well as that obtained after the blast. The following information available from a mineral exploration drilling program was used in the prediction of fragment size distribution: largest piece, percent particles larger than 1 inch and RQD. Photographs of bench faces were used to estimate the fragment size distribution. Fracture spacings were evaluated along a series of parallel lines on the photograph. Photographic techniques were also used to obtain the grain size distribution of blasted material. m is paper describes the methodologies applied in some detail.

Jan 1, 1986

By William Everett, Jack Eloranta

United Taconite is an iron ore mine operated by Cleveland-Cliffs Inc (Cliffs) located near Eveleth, Minnesota. The mine, originally known as Eveleth Taconite Mines, was purchased in December 2003 by Cliffs (70%) and Laiwu Steel (30%). The mine site, known as the Thunderbird Mine, produces taconite ore for delivery by rail to the company’s Fairlane plant, located approximately 10 miles to the south near Forbes, Minnesota. At the plant, the crude ore is ground, concentrated and processed into pellets for steel industry customers. Total pellet production capacity is about 5.4 million long tons (Ltons) per year.

Jan 1, 2006

By H Fukui, K Ichikawa, K Aikou, E Suzuki

An electronic delay detonator (EDD) consisting of a digital-base electronic delay module and a conventional instantaneous detonator module, designed for series connections with a special adjustable-output blasting machine, is described and shown to provide a delay time accuracy some four to twelve times higher than that of pyrotechnic millisecond and decisecond delay detonators, together with the other performance characteristics necessary for practical use. Also described is a blasting design system which allows effective reduction of ground and air vibration, through the use of EDDs with optimum delay times as determined by accurate computer simulation based on wave form and other data obtained from an on-site single-shot test blast.

Jan 1, 1989

By Bruce B. Redpath, Thomas E. Ricketts

Scaling laws commonly used for describing or predicting blast motions generated by conventional arrays of blastholes are dimensionally incorrect. The scaling of distance by the cube root of charge weight is correct only for spherical charges, and scaling by the square root of charge weight is incorrect for any charge configuration, although both approaches may result in empirically useful formulas for a limited range of charge sizes. Analysis of motions generated by a large set of underground blasts shows that scaling distance by the square root of the linear charge density, which is dimensionally correct for a cylindrical borehole, yields much more consistent results than the traditional scaling rules. Further, this scaling law is valid right up to the free face of the burden. A significant result of this work is that the peak particle velocity for an array of blastholes is primarily dependent on blasthole diameter and not on total charge weight or maximum explosive weight per delay, which are the commonly used parameters for scaling seismic amplitudes generated by conventional blasting arrays.

Jan 1, 1987

By B Mohanty, R Yang

Blasting vibration information is now commonly used to diagnose blast malfunctions. These range from limiting vibration levels to protect normal dwellings to determining scatter in detonator firing times, and even to rating of explosives in the borehole. Although blasting vibrations have the potential to yield reliable information in all these issues, there are key restrictions on their specific use, which are often ignored. These include all aspects of instrumentation, and sensor layout, as well as methods of analysis. This paper highlights these limitations. It emphasizes the distinction between near-field and far-field seismic recording in terms of borehole dimensions and blast geometry. Several case studies from both underground and open-pit blasting operations are discussed to illustrate and emphasize the essential characteristics of blasting vibrations and their optimal use in diagnosing blast malfunctions.

Jan 1, 1997

By Timothy Stark

At present blasters are strictly liable under tort law for personal injury and property damage caused by ground vibrations and/or air overpressures. The application of strict tort liability to vibration and air overpressure damage has resulted in litigation that has hampered and probably will continue to hamper the blasting industry. There are many case histories in which blasters have been sued for the appearance of cosmetic cracking, some of which have involved frivolous claims and marginal expert testimony (Oriard 1999). This litigation has resulted in additional costs to the blasting and construction industries and the American public because there are usually many plaintiffs involved and each case is usually adjudicated separately instead of under a class-action format. It is proposed herein that blasters not be held liable for vibration or air overpressure damages unless their conduct is proven to be negligent. A number of reasons are presented for raising the legal standard from strict liability to negligence including: (1) improvements in blasting technology that allow blasting to be conducted without substantial risk of damage and if damage does occur it is likely to be cosmetic, (2) establishment of conservative ground vibration and air overpressure damage limits for typical structures, and (3) established industry standards for construction blasting.

Jan 1, 2002

By E Emery Jr Gray

A need for more delay periods other than those normally manufactured throughout the explosives industry rarely occurs. This paper will discuss one such incident from an analytical view through practical application.

Jan 1, 1976

By A B. Andrews

The use of sequential blasting techniques that combine surface and in-thehole delays has provided blasters with increased flexibility in blast design to promote good rock fragmentation and displacement while minimizing offsite blast effects such as air blast, flyrock, and ground vibration.

Jan 1, 1981

By Ray Jambakhsh, Craig Copping

The St. Lawrence Seaway's Welland Canal has been undergoing a rehabilitation program that requires the removal of deteriorated concrete from the 25 meter high lock walls. Multi million dollar contracts must be completed during the three month winter freeze up. New blast designs have drastically cut the time required for concrete demolition. All blast results including vibration, noise, underbreak, overbreak, scaling and flyrock have been improved and at a lower cost.

Jan 1, 1994

By Gerald R. Coonan

Laboratory research is being conducted to substantiate suggested levels for voluntary standards on human response to transient vibration. The application of those findings to actual field conditions, however, will be limited because they will not include social and psychological factors existent in the real world. It is necessary, therefore, to examine available empirical information on complaints in an attempt to define the influence social and psychological factors might have on the laboratory results.

Jan 1, 1982

By Paul N. Worsey

Disturbed zones of rock have been measured for blasted highway rock cuttings by Matheson and Swindells of the Transport and Road Research Laboratory (TRRL) of Great Britain. These zones have been shown to be directly attributable to the blasting process and accordingly vary in depth depending on blasting technique. Perimeter blasting such as smoothwalling and pre-splitting has been shown to be effective in reducing the depth of disturbed rock. Although extensive work has been carried out on surface excavations for medium diameter (l00mm) blast holes, none has been undertaken for underground excavations.

Jan 1, 1985

By Michael Wieland

Delay blasting in underground coal generates shock waves and rifting forces that damage charges remaining in the blast pattern. Damaged charges detonate poorly, raise fume toxicity and reduce coal breakage. Such circumstances could be prevented by using explosives resistant to cross-hole interaction damage. The design of rugged explosives is fraught with contradictory requirements, but tradeoffs related to hard-particle size characteristics prove useful. Hard particles, related voids or trapped bubbles represent reaction nucleation centers which strongly influence the performance of coal mine explosives.

Jan 1, 1992

By Thomas A. Gelormino, Ulrich La Fosse

"Deep blasting was used to densify foundation soils for a large manufacturing facility inChicopee,Massachusetts. A 360,000 square foot building, whose construction began inthe summer of 1990, is founded on alluvial deposits up to 90 feet in depth. These deposits are comprised of saturated very loose to loose fine to medium grained sands with traces of silt and gravel. During the building foundation design it was found that to withstand earthquake forces without soil liquefaction, it would be necessary to improve portions of the alluvial deposits by densification. The zone in need of densification extended from approximate depths of 20 to 50 feet. Several conventional densification methods, including vibrocompaction and deep dynamic compaction, were evaluated along with deep blasting. Detonation of 1-3/4 inch diameter charges of 65 percent gelatin dynamite (Atlas Power Primer) installed inside 2-inch diameter PVC casings to a depth of up to 40 feet, was used to achieve the desired densification. This method was selected over others due to its lower cost and decreased construction time. Although used in New England once in1940 for a dam and once in 1960 for a transmission line tower to improve foundation soils, there is no precedent found in the literature for densification by blasting to improve liquefiable soils below a proposed building. Details of a test program and the production blasting, including vibration data are presented. Pre-and post-blasting data conclusely shows an increase in the density of the sand deposit after blasting."

Jan 1, 1991

By Edward Fitch

The DOE is evaluating Yucca Mountain, Nevada as a potential site for disposal of high level nuclear waste. Yucca Mountain is located approximately 160 km northwest of Las Vegas on the western edge of the Nevada Test Site and the Nellis Air Force Range. An exploratory tunnel has been constructed through Yucca Mountain for site characterization. A controlled drilling and blasting technique, smooth wall blasting, was used to excavate the TBM starter tunnel and alcoves off the main tunnel to provide areas for scientific investigation. Fundamental to the blasting program has been the use of two blast design equations used in concert to minimize blast damage to the surrounding rock mass. The first of these equations was developed by Roger Holmberg and estimates near-field peak particle velocity that is the basis for minimizing blast damage to the host rock. The second of these equations was developed by B. H. Sanden and provides bore hole pressure estimation which allows controls to minimize crushing of the rock mass along the perimeter yet allowing enough force to create tensile failure between perimeter bore holes. This is key to the smooth wall blasting technique. To date, essentially the same controlled drilling and blasting program has been in place for all excavation requiring controlled drilling and blasting at the ESF. The controlled drilling and blasting program uses an iterative process to achieve continuous improvement in the blast rounds. This involves interaction between Architect and Engineer (A/E), Constructor, and Testing Coordination O&e (TCO) to ensure each blast round successfully meets the expectations of affected participants. The A/E requested that the TCO provide validation of the near-field peak particle velocity estimation under the Construction Monitoring Program. Data gathered under this program were reduced by statistical analysis and used to verify blast design parameters and provide a site specific blast damage relationship.

Jan 1, 2000

By RR Vandebeek, A W. Bauer

The Canadian Explosives Research Laboratory regularly evaluates the properties of commercial explosives for authorization under the Canada Explosives Act. Propagation sensitivity is normally measured using small scale tests. Relating the results in actual mining practice is difficult. In the mining industry, the propagation sensitivity is a measure of the ability of one cartridge to propagate to an adjacent cartridge in a borehole. They may be separated by a gap of in-filling material. As well the propagation sensitivity will be affected by the explosive type, temperature, degree of coupling, cartridge diameter and other factors.

Jan 1, 1987

By Dale Preece, Stephen Chung, D. Scott Scovira

The DMC_BLAST (Distinct Motion Code) has been developed to model rock motion and displacement during the gas expansion phase after the detonation of an explosive in a borehole. Recently, a designated delay firing order algorithm was written into the DMC_BLAST code. The model can now be used to analyze rock mass displacement for a V-cut, center opening, or sinking cut initiation sequences. This new feature allows the investigation of the effects of delay firing order on rock displacement when blasting complex inter-bedded and ore-waste structures. The model provides important ground movement and mixing indicators for dilution control in surface gold mining relative to the initiation sequences employed. Echelon blasts as compared to center opening type blasts show differences in their internal muckpile displacement. These displacement differences can be important to operations that mine narrow strike driven ore bodies. The model also has applications to through coal seam blasting and demonstrates that down-dip blasting is a better alternative than up-dip blasting. There is less disturbance to the dipping coal seam and less mixing of the rock and the coal.

Jan 1, 2000

By Salah A. Taqieddin

The blast casting technique of removing overburden is an innovative technique which was successfully used in the mining of certain surface coal and quarries. This method was found to be efficient in minimizing the labor and equipment cost while accelerating mining operation with safety. This method was successfully applied to horizontal as well as to dipping coal seams. Also it was practically applied to single as well as to multiple ore bodies

Jan 1, 1992

By B. A. Cheeseman, R. Skaggs, C. F. Yen, S. Wolf

Shallow buried explosives pose a significant threat to lightweight vehicles and their onboard personnel. To date, designers of lightweight vehicles are limited in their knowledge of what occurs during the blast. The high intensity, short term loading imparted by the explosion is enormously complex and can be significantly affected by a number of parameters including the size, shape, type, detonation point and depth of burial (DOB) of the explosive and the type, density and water content of the soil. Recent advancements in numerical simulations have enabled the complex blast event to be accurately modeled by coupling Eulerian and Lagrangian analyses: the former is well suited to modeling the blast and while the latter, the structural response. Further validation of the modeling technique is considered in the current paper, which details simulations performed utilizing the coupled Eulerian-Lagrangian analysis to the study the blast output of explosives buried in saturated sand. These experiments varied explosive charge size, its depth of burial, the target stand-off (SO) distance and target plate dimension. The investigation concludes with a discussion of the accuracy of the numerical simulations when compared with the experimental observations.

Jan 1, 2005

By Dale S. Preece

A discrete element computer program, DMC (Distinct Motion Code), has been used for several years to simulate blasting-induced rock motion. Recent enhancements of DMC's capabilities have included addition of an algorithm that couples together rock motion and gas flow. This allows the user to specify a particular explosive which also specifies equation-of-state and other parameters necessary to model explosive gas flow from the blastwell. Rock loading by the flowing gas is calculated automatically. The mechanism for calculating the rock loading is the subject of this paper. The rock motion effects the gas flow calculation by changing the porosity. DMC is currently being used on a SUN SPARCstation 2 computer workstation.

Jan 1, 1993

By David Leidel

A major characteristic that distinguishes modern society from its predecessors is the understanding that events are not driven by the whims of the gods, pre-ordained fate or nature, but are controlled to a greater or lesser extent by the actions, (or inactions), of people. The study of risk assessment is the basis for determining risk or the likelihood of an event occurring combined with the consequences of that event if it does occur. This study is indubitably linked to the mathematics of probability and statistics which permits the quantification of risk. As the Industrial Revolution significantly increased the exposure of persons to new types of energy sources, materials, equipment, and means of more rapid transportation of goods and people, quantitative risk assessment became a vital tool in protecting workers and the general public exposed to these new technologies.

Jan 1, 2007