Search Documents

By Y. S. Sun, P. Gao

Compared with conventional roasting and magnetic separation processes, higher reduction temperatures and stronger reducing atmospheres are used in reduction technologies to reduce iron oxides to metallic iron, which is often liberated during reduction and amenable to magnetic separation. Reduction and magnetic separation of an Australian refractory iron ore was therefore studied as a function of reduction temperature, time, coal addition, feed thickness and size of Australia iron ore. It was found that during reduction, the particle size of the reduced iron increased with reduction temperature and time. Subsequent magnetic separation tests were further conducted on the reduction products. A reduced iron powder with a Fe grade of 85.67% was obtained at a Fe recovery of 87.82% under optimum reduction conditions where a metallization rate of 85.82% was achieved. The mechanism involved in reduction is discussed based on XRD and SEM examinations. And the results indicated that theiron minerals such as hematite and limonite in the Australian iron ore were reduced as follows: Fe2O3?Fe3O4?FeO?Fe. Furthermore, the metallic iron particles produced by reduction increased in size with longer reduction times.

Jan 1, 2014

By G. M. Wolfaardt, B. C. Qi

"From a lifecycle point of view, biologically digested sludge is a valuable product that should be reused if possible. Sludge may be applied to agricultural land for further sludge treatment and improvement of the characteristics of the soil. The characteristics of sludge that affect its applicability for soil conditioning include moisture content, pathogens, nutrients and metals. In this paper, the use of solid anaerobic digestion sludge of the lignocellulosic residues to condition soil was investigated in regards to nutrient composition, water content/retention capacity, hygienic quality (contamination of pathogenic bacteria) and heavy metal adsorbing/releasing characteristics of the sludge.It was found that the digested sludge had approximately 44.5% free and immobilized water and 46.9% bound water. The water-holding capacity of the sludge was high. This was a merit to apply the sludge to agriculture in dry areas. Anaerobic digestion under thermophilic conditions showed a promising disinfecting effect to the sludge, in contrast to the landfill digestion. The anaerobic digestion sludge could be considered as a humus-rich hygienic product that improves soil fertility and water holding capacity, nourishes plants and immobilizes heavy metals in the environment"

Jan 1, 2003

By Marco Le Roux, Quentin Campbell

"Most coal supply contracts include strict limitations on the moisture content of the products. This limitation exists because of calorific, transport cost, and handling reasons. Managing the retention time on product stockpiles to facilitate drainage commonly controls the moisture content in coarser coal products. A large-scale pilot rig has been commissioned to facilitate research in this regard. A stockpile of about 15 tonnes of a typical washed power station feed coal from the South African Witbank coalfield was loaded onto a 6 x 6 m platform on load cells. The platform was shielded from the elements, like rain and wind, and an artificial rain sprinkler system was installed. A variety of rainfall intensities and durations were simulated and the water accumulation and run-off was measured. The material was also sampled for moisture and particle size before and after the series of tests. At the same time, the drainage characteristics of the same coal were determined in smaller scale drainage columns for comparison. Data is presented in this paper on the drainage rates, maximum accumulated moisture, final moisture, and the effect of evaporation. The results showed that for all rainfall patterns tested, drainage ceased after 2 - 3 days, but evaporation continued for at least the time period under investigation, albeit at a low rate. Evaporation contributed to dewatering at rates that depended on wind, temperature and humidity conditions. This caused a slow reduction in moisture content even after the run-off had ceased. The value of the final moisture depended on the coal PSD. It was also found that the intensity and duration of the more intense rainfall events did not significantly affect the maximum water accumulation, with drainage rates equaling the corresponding water addition rates which suggested that water ran off over the surface of the stockpile with limited penetration. During more intense rainfall scenarios, some penetration was apparent."

Jan 1, 2014

By Mahdi Shevrini, Hamed Haghi

"In this research, the operation of screen classifying in silica processing circuits was investigated and modified by replacement of available trommel screens with teetered bed separator (TBS). In addition the effect of the mentioned replacement and addition of attrition scrubber on quality of final product, impurities removal, recovery and production rate were inspected. Considering screen efficiency problems to achieve certain particle size distribution, hydraulic classifying system was selected instead of trommel screens. Application of suggested plan improved quality and particle size distribution of produced silica significantly. Optimization of size classification in process circuit resulted in increase in production rate up to 21% (from 67% to 81%), silica recovery (from 68.35% up to 83.11%) and relative enhancement in removal of impurities such as Fe2O3 and TiO2. After optimization and stabilization of grinding and size classification section, industrial attrition scrubbing tests were carried out and the best solid percent and retention time were determined i.e. 70% and 6 minutes, respectively. Using sodium carbonate during attrition scrubbing, has major effect on removal of surface coating and staining especially sharp increase in clay removal; therefore 2 kg/t of sodium carbonate can be optimistic point of industrial procedure for this silica processing plant. It should be mentioned that application of attrition scrubbing which is followed by screw classifier for de-sliming were useful for better cumulating of particles in the range of appropriate liberation degree (+106-300µm) and efficient removal of metallic (iron and titanium oxides) and non-metallic (clays and feldspars) impurities."

Jan 1, 2014

By Kunihiko Yamaguchi, Gjergj Dodbiba, Toyohisa Fujita

Usually magnetic separation is performed to separate ferromagnetic, paramagnetic and diamagnetic particles by controlling magnetic field strength. In this research the wet high gradient magnetic separation at various kinds of magnetization of medium has been investigated to separate different kinds of magnetization of paramagnetic mineral particles from each other. Most of week paramagnetic particles are captured at high magnetic field using superconducting magnet. If the magnetization of fluid is larger than that of paramagnetic particle, the paramagnetic particle cannot be captured in the direction of magnetic field. The paramagnetic particles of different magnetization such as hematite, chromium oxide, perovskite and rutile are separated in different magnetization of fluids. These particles are present in the incinerated bottom ash. The separation is useful to recover titanium oxide from bottom ash and the removal of chromium of bottom ash is important to reuse the bottom ash as cement. The used fluids are paramagnetic liquids dissolving paramagnetic salts and the water based magnetic fluid dispersing the stable ultrafine magnetite. The dispersion condition of particles related to zeta-potential of the suspension feed is also important to separate effectively by controlling pH

Jan 1, 2014

By Roberto Galery, Priscila Esteves, Braz Cardoso, Marcelo Stopa

"It was developed in this work a computational tool to aid in anomaly detection present in the operation of ball mills. The tool uses a torque estimator that is based on measurements taken exclusively in the drive motor. The ball mill equipment widely used in the mining industry has, inherent to its principle of operation, high energy consumption and low efficiency. These characteristics are accentuated when the mill operates outside the ideal conditions of velocity and loading. Direct measurement of these variables is extremely difficult because it requires the installation of sensors in moving parts of the mill. Thus, systems that can help monitoring the operating conditions and predict anomalies are useful because they contribute to improving the performance of the process, help to reduce the energetic consumption, wear on the mill surface and frequency of maintenance shutdowns. The detection strategy implemented in this work is based on the fact that operational anomalies such as an inadequate percentage of balls and incorrect angular velocity manifest itself as a change in spectral components of the torque signal in the mill driven by an electric motor. The mill torque was estimated by processing motor variables measured by sensors commonly used for control purpose and installed exclusively in the motor. The mill was operated at various fault operating conditions and signals from electric motor and vibration on the mill shaft were measured. The spectral components present in the estimated torque signal were then compared with signals from a vibration sensor in order to establishing a correlation with anomalous operation condition of the mill. The experimental results showed that the signals obtained has an excellent correlation with other variables obtained by direct measurement and have potential to be used to construct a system for automatic fault detection in the operation of ball mills."

Jan 1, 2014

By G. K. Nimal Subasinghe

The performance of Knelson Concentrators (KC) used in gravity gold circuits often rely on manufacturers recommendations for selecting operating parameters such as, fluidising water flow rate and cycle time. These parameters are not only dependent on the machine parameters but also on the feed characteristics such as, size distribution of the gold and gangue particles and the composition of its constituent minerals. Particles entering a KC experience a centrifugal acceleration due to the high bowl rotational speeds. The required centripetal force to maintain a circular orbit is provided by the fluid drag force created by inwardly moving fluidising water and the Bagnold?s force arising from the particle/particle collisions. When the fluidising water flow rate is low particles move towards the outer rim of the bowl forming a packed bed within the grooves. On the other hand, if the fluidizing water flowrate is high the bed expands and some particles would move towards the centre of the bowl and gets carried to the tailings stream, thereby reducing the amount of material retained within the grooves of the bowl. Based on a force balance on a particle captured within the KC, a criterion which can be used to predict the amount of material recovered in the bowl has been derived and validated by experimental data. It has been shown that this criterion may be used to demarcate the transition of the bed from a packed-bed state to a fluidised state depending on the fluidizing water flowrate. By identifying the conditions for the optimal expansion of the bed comprising different constituent mineral particles, it is possible to estimate the optimal fluidising water flow rate that would maximise gold recovery while minimising gangue recovery. It was also observed that the accumulation of valuable mineral in the bowl takes place by the displacement of the gangue particles in the bed by the incoming heavy mineral particles. The kinetics of this segregation process was also studied using synthetic mineral mixtures. The experimental data suggests that this process follows first order kinetics and that the build up of heavy mineral reaches a maximum which could be used to identify the optimal cycle time. In this work, the suitability of the above model in optimizing the performance of a KC have been reviewed. Also the necessity and merits of testing an unaltered

Jan 1, 2014

By Milind Sabne, Pradip, P Kapur, Beena Rai

"The efficiency of an industrial flotation circuit depends on (a) the selectivity and the kinetics of the reagent combination selected for the separation (b) the hydrodynamic conditions prevailing in the flotation cell (essentially equipment design parameters) affecting both the pulp and froth phase (c) the operating parameters such as feed rate, pulp density, pH, temperature etc. including the mineralogy, particle size distribution and relative proportion of liberated and composite particles of constituent minerals in the feed to flotation circuit and (d) the circuit configuration itself. We have developed a molecular modelling based reagent design and selection framework to assist mineral engineers to arrive at the preferred reagent combination based on a rigorous, scientific and quantitative comparison of various options available for this purpose. Similarly we have also utilized a general circuit design methodology proposed by Kapur and Mehrotra in 1974. The advances thus made in modelling both the reagent chemistry as well as circuit design, along with the availability of sophisticated, automated tools for characterization of ores (liberation as well as mineralogical composition of the different flotation streams) provides a scientifically rigorous, quantitative, robust framework for design and optimization of complex flotation circuits. We illustrate in this paper the power and the utility of our rigorous optimization based approach to designing industrial flotation circuits for the beneficiation of a multi-component feed with the help of few case studies from our own work. With the proposed methodology, higher levels of process efficiencies can be achieved in the industrial flotation plants, in particular those processing complex, multi-component feeds requiring multiple stages of flotation separation. We are currently developing an IT platform consisting of computer-aided decision support tools for arriving at the preferred flotation circuit and the appropriate reagent chemistry for a given ore deposit and/or a given plant."

Jan 1, 2014

By Atsushi Shibayama, Toyohisa Fujita, Wan-Tai Yen, Ke-jun Liu

"In this investigation, a sponge gold sample (99.92% pure) has been leached with ammonium thiosulfate solution. The effects of CuSO4, (NH4)2S2O3, (NH4)2SO4, NH4OH and retention time on the gold leaching % (extraction %) and thiosulfate oxidation % (consumption %) have been studied. The copper ion acts as a catalyst in gold dissolution. On the other hand, it also accelerates oxidation of thiosulfate (consumption). It was found in this study that the best gold extraction condition was obtained at 43.2 ks with 0.8 - 1.0x103 mol/m3 (NH4)2S2O3, 30 mol/m3 CuSO4, 2.0 - 3.0x103 mol/m3 NH4OH, 0.4 - 0.5x103 mol/m3 (NH4)2SO4, pH 10±0.2 and 150 rpm. The thiosulfate oxidation was about 15% of the initial concentration.For gold recovery from the pregnant solution, the trioctylmethyl ammonium chloride (TOMAC) was used in this investigation as an extractant to extract gold from thiosulfate solution without pH and other adjustments. The effects of gold concentration, pH, ammonia, thiosulfate and cupric ionic concentrations, extractant and diluent concentrations and retention time on the gold recovery were investigated. It was found that 180 mol/m3 extractant diluted with n-octant at O/A ratio of 1:1 could extracted the 100% of gold in 0.6 ks from the thiosulfate solution at the optimal leaching conditions. The 100% gold stripping could be achieved with 10% thiourea solution."

Jan 1, 2003

By Rong Fan, Andrea Gerson

"The small recovery of Ag, often in the order of 50%, by traditional flotation and leaching process strategies is closely related to the complicated and heterogeneous nature of Ag-bearing minerals with Ag typically being associated with numerous minerals within any given ore-body. Moreover, grain sizes may be extremely fine with micron-scale common. In order to design cost-effective Ag-bearing mineral flotation and leach recovery strategies it is firstly necessary to characterise the speciation of Ag and its correlation with other elements, e.g., Cu, As and Sb, within the ore matrix and process streams. The traditional QEM-SCAN analytical approach can prove problematic for some mineralogies due to difficulties in recognising degrees of crystallinity, polymorphs, complex solid solution series, high value trace element mineralogy, very fine grained materials; and the requirement for a comprehensive data base. Moreover, there is difficulty ‘seeing’ either surface films or surface contaminants which can both lead to poor flotation performance. There is therefore clearly a need to develop confirmatory and complementary approaches when these uncertainties arise. Synchrotron X-ray microprobe analysis provides a powerful tool for the mineralogical characterisation of finely segregated heterogeneous Ag-containing materials. These measurements enable comprehensive characterisation of the Ag-bearing components using synchrotron microprobe X-ray fluorescence mapping (µ-XFM), X-ray diffraction (µ-XRD) and X-ray absorption spectroscopy (µ-XAS). Further analytical strength is provided by principal component analysis of laboratory ToF-SIMS data which enables the statistical identification of correlated surface species enabling examination of surface chemical characteristics responsible for mis-reporting of Ag containing components within flotation streams. We describe the application of these techniques to a selected Ag-containing feed and tail and demonstrate how these compliment and extend traditional analytical methodologies."

Jan 1, 2014

By S. Swaroopa

Copper-chromium mixed oxides are widely used as catalyst for organic chemicals industry, NOx and CO oxidation, solid propellant etc. In the present investigation, one such spent Cu-Cr catalyst has been tested for recovering copper and chromium values through hydrometallurgical route. The spent catalyst used in this study contains about 42% Cu and 36% Cr. Phase analysis through XRD indicates that major phases are copper chromium oxide (CuCrO2) and copper chromate (CuCr2O4) while minor phase is copper oxide (Cu64O). SEM images show that high energy ball milling changes surface morphology significantly ? more regular shaped grains in unmilled samples changed to fine agglomerates. Surface area also changes significantly due to milling. Preliminary leaching experiments with NH3 and H2SO4 media using unmilled samples indicate that both the media are suitable for selective extraction of copper. About 55% copper recovery is achieved in 2 h using 1.2 M NH3 + 0.2M (NH4)2SO4 solution at 100°C. Increasing NH3 concentration or temperature does not improve the recovery significantly. Under the above conditions chromium, dissolution is insignificant (max. 2.24%). XRD analysis of the residue indicates that copper chromate fraction (CuCr2O4), which is a spinel structure, remains mostly intact. In sulphuric acid media at ambient temperature, 47% copper recovery is achieved with 7.5% (v/v) H2SO4 and maximum of 57% with the increase in acid concentration to 20%. However, 67% recovery is achieved by increasing the leaching temperature to 150°C. High energy ball milled samples show improved leaching efficiency. Under the leaching conditions of 7% H2SO4 (v/v), 2% pulp density, 80°C an unmilled sample yields 47% Cu recovery whereas 3h and 5h milled samples yield 65% and 90% Cu recovery respectively in 2h leaching time. Influence of temperature is also more pronounced in milled sample leaching in comparison to unmilled sample. Water leaching of alkali (NaOH) roasted milled sample carried out at 750°C for 2 h with 100% NaOH (w/w) resulted in 80% Cr recovery as compared to 37% Cr recovery using unmilled sample under the same conditions. Keywords: spent catalyst, copper, chromium, leaching, mechanical activation, roasting

Sep 1, 2012

By A. Üçyildiz

Magnesium borates of varying compositions and properties are synthesized using different reagents and methods for the possible potential uses as termoluminescent material, anti-wear and anti-friction additive, fire retardant, catalyst for the conversion of hydrocarbons, whisker material and ferroelastic material. In the current work, the conditions for synthesizing MgB4O7 compound by high-temperature solid-state reactions were investigated using boric acid and magnesium oxide as the starting materials. The MgO:B2O3 mole ratios applied in the experiments were 1:1, 1:2, 1:3 and the thermal behaviours of each mixture were studied between 25~1200°C by TG/DTA analyses under static air atmosphere to find out the probable formation temperature of MgB4O7 phase. Considering TG/DTA results, freshly prepared boric acid and magnesium oxide solid mixtures were heated at predeter-mined temperatures and the phases were identified by XRD analyses. Accordingly, MgO:B2O3 mole ratio of 1:2, heating temperature of 950°C and a reaction time of 2 hours were selected as the optimum conditions for the formation of maximum amounts of MgB4O7. After obtaining solids prepared at the pre-determined optimum conditions, their chemical composition, IR spectrum, TG/DTA pattern, B.E.T. surface area value, particle size distribution and SEM images were deter-mined to point out the possible use areas. Experimental results showed that it was not possible to obtain pure product at the optimum conditions due to formation of minor amounts of t-Mg2B2O5 and the presence of some unreacted B2O3. The product synthesized has the potential for use as a corrosion inhibitor on some metal surfaces.

Jan 1, 2014

By S. M. Viduka

This paper presents a numerical investigation of solid separation in jigging device, which is a gravity separation method widely used in ore processing. Separation is recognized as being heavily dependent on fluid motion in the jig. This study explores the effects of the inlet time dependent velocity profile on jigging performance. Modelling of the liquid-solid system is performed through a combination of computational fluid dynamics (CFD) to simulate liquid flow and discrete element method (DEM) to resolve particle motion. The initial packing conditions consist of a binary-density particle system of 1130 particles each 1 cm in diameter. A variety of jigging profiles are implemented in jigging. The saw tooth pulsation profile is selected with three variations in both amplitude and frequency. The performance of each profile variant is compared in terms of solid flow patterns, separation kinetics, energy, and mean particle position. These quantitative comparisons demonstrate significant differences in the segregation rate, energy, and solid phenomena, helping find an alternative optimum operating setting for the system.

Sep 1, 2012

By Chuanyao Sun, Longli Liu, Fayu He, Guiye Wu

Utilizing thioglycolic acid (TGA) as a template and using structure-guided design, a molecular modelling approach has been used to design and screen appropriate dispersant for chalcopyrite. A series of organic dispersants based on a TGA substitution with hydroxyl and amino and sulfonic functional groups have been examined on chalcopyrite surface. 20 organic depressors of chalcopyrite have been investigated to study the quantitative structure-activity relationship (QSAR) of chalcopyrite depressors. For the chalcopyrite surface, depressor containing carboxyl and sulfonic group is generally stronger than the depressor containing hydroxyl group. Increasing the number of hydrophilic group can effectively enhance the inhibition. Increasing the number of Solidophilic group does not necessarily lead to enhanced inhibition ability; steric factor is one of the important factors to affect the interaction. Extension alkyl carbon chain length cannot enhance the interaction of depressors. Isomers principle as well as applies to the chalcopyrite depressor molecular design. Flotation verification tests further confirmes the accuracy of the molecular simulation. Through the Computer Aided Molecular Design (CAMD) technology, we can save enormous time and resources to design novel surfactants. This research and application will play a great significance role in sulfide flotation.

Jan 1, 2014

By Z. B. Pan

The innovative point of this new technology can be described that under normal pressure and 70°C, using a new combined activating and oxidizing agent, the minerals bearing arsenic and organic carbon are oxidized effectively. This technology can be applied in commercial scale. The high carbon and arsenic bearing gold ore is taken from Gansu, where hundreds of tons gold deposit. The ore has 0.51% of arsenic and 1.75% of carbon (1.07% of organic carbon). The gold occurs mainly in native with particle size 0.02~0.6 mm and a few are enwrapped by pyrite and arsenopyrite. The traditional cyanide leaching process gains a very low gold leaching rate with only 5%. Through systemic experimental study, the technological flowsheet of flotation process for concentrating gold, then pre-treating the gold concentrate followed by cyanide leaching the gold concentrate are used. With 4.92 g/t gold of head sample, the gold concentrate with 46.52g/t gold grade and 96.53% gold recovery is gained by flotation process. Followed by pre-treatment for 6 hours, the gold concentrate is leached with cyanide after filtration and washing. The total gold leaching rate is up to 95.44%.

Jan 1, 2014

By A. Lewis

"Thiol collectors including the xanthates and dithiophosphates have dominated the sulfide mineral processing industry for over a century. Tecflote represents completely different chemistry, without sulfur or phosphorus, and will float all sulfides and associated precious metals. As these collectors are surfactant in nature, they comprise a head group which binds to mineral surfaces, a spacer and a long hydrophobic tail. The modification of the spacer behind the head group allows for collector optimisation for different sulfide ore types and process conditions.The Tecflote surfactants have been designed to be either very selective against pyrite at the natural pH of the ore (pH 7-9) or to float all sulfides including pyrite. Depending on the ore type and the process flow sheet, the use of lime can be maintained, reduced or completely eliminated.Tecflote can be used either as a rougher collector giving good recovery and grade for the sulfide minerals or it can be used to target valuable minerals after regrind and through cleaner flotation. It has repeatedly shown to be very effective at holding onto gold through the cleaner steps. The low solubility has a significant impact on the mechanism and surface activity of the collector, resulting in a very different flotation response compared to conventional thiol collectors.INTRODUCTIONXanthate was first made in 1882 by Zeise and first used in flotation in 1924 (Keller, 2018). In 1946 Keller patented thionocarbamate as a collector, which was produced by Dow Chemicals (Keller, 2018). Later it was replaced by Dow product Z-200, while dialkylthionocarbamate was discovered by Harris et al. (Harris, 1954. No significant chemistry change to collectors has occurred since they were introduced in the mid-20th century and now that the feed grades have been declining over the last decades creating a need to find more selective collectors to extract difficult and complex ores and pushing the industry to look at other reagents."

Jan 1, 2018

By I. N. Babich

"Complex technological problems associated with the processing of mineral raw materials require the search and development of new means and ways of thinking. At present, computer cognitive graphics (CCG) are one of the most actively developing areas of new information technologies. The aim of the study was to optimize the cycle of technological evaluation of ores at all stages of geological exploration of deposits on the basis of analysis of geological sampling data using CCG. A new approach has been developed that facilitates optimization of the whole cycle of subsoil exploration. At the gold ore deposit, the results of the geological sampling data were processed by the method of constructing the CCG in the form of a histogram showing the frequency of gold extraction and the average amount of its content. Significant peaks of the metal content in the ore, exceeding the level of the average content in the ore by tens of times, have been revealed. Graphical interpretation of the parameters of mineralization reflects the uneven nature of its variability, which indicates the presence of large, rarely occurs of gold in the ore and the need to conduct studies on a sample of ore of greater mass than for ores with tiny gold. On a sample of 50 kg gold-quartz ore studies were carried out on gravity enrichment. The maximum size found in the gold concentrate was 0.07 mm. In the course of integrated tests in a gravity concentrate, gold particles up to 3 mm in size were found, which predetermined the need to include the operation of gravity before flotation. A new approach to subsoil research is protected by a patent (RU 2620823).The technological problems that arise before the researcher associated with the processing of resistant ores require the exploration and development of new means and ways of thinking. New problematic situations on complex mineral and raw materials objects are practically not amenable to resolution by existing methods. Integration of industrial and information technologies is necessary. At present, computer graphics (CG) is one of the most rapidly developing areas of new information technologies. For example, in scientific research, including in fundamental research, the accent from the illustrative function of CG (the visualization of what is already known) is increasingly shifting towards the use of computer cognitive graphics (CCG) tools (Bashlykov, 2016). The function of the CCG is to obtain a new knowledge with the help of a graphic representation - a cognitive image or at least to promote the intellectual process of the logical acquisition of this knowledge. In this study, cognitive images are used to graphically represent the distribution of valuable components in the bowels of the deposit, characterizing the state of mineral-raw materials."

Jan 1, 2018

By S. Castro

Molybdenite flotation is strongly depressed at pH higher than 9.5 in the flotation of Cu-Mo ores in sea water. Chemically sea water contains mainly Na+ and Cl- ions, but also some secondary ions, such as SO42-, Mg2+; Ca2+, HCO3-; etc., which are not necessarily indifferent for the flotation of molybdenite. The natural floatability of molybdenite in sea water and in NaCl solutions containing different secondary ions is investigated by micro-flotation tests. The tests indicate that the floatability of molybdenite in alkaline media in 0.6 M NaCl solutions is not affected by the presence of anions, such as, SO42- and HCO3-, at concentrations similar to those occurring in sea water. However, a strong depression of molybdenite at pH ranging from 9.5-10.0, is produced by the alkaline earth metal cations (Ca2+ and Mg2+ ions), dissolved in distilled water or in 0.6M NaCl solutions. It was found that effect of Mg2+ions is significantly stronger than Ca2+ ions. Effect of both ions is attributed to hydrolysis and adsorption of MOH+ hydroxy-complexes. This is followed by subsequent precipitation of hydrophilic colloidal hydroxides at the molybdenite/solution interface, and in bulk solution.

Sep 1, 2012

By V. K. Kuppusamy, M. Holuszko

"Lamps and lighting products are the most commonly used electrical products around the globe. With the improvement in lamp technologies, lighting products have grown complex and hence require an improved recycling process. The LED lamps consist of various valuable metals such as iron, copper, aluminum, chromium, silver, and gold, as well as non-metals such as glass, plastics, and fibers. In addition, there are also traces of hazardous substances such as lead, arsenic, and mercury. A major step in the recovery process is size reduction, and researchers have suggested that up to 40% of the total valuable material is lost during the shredding and grinding processes. SELFRAG is a high voltage selective fragmentation comminution technology that uses high voltage pulses in a water medium to efficiently separate the metals at a coarser size without generating many fine particles. It has been proposed that during the fragmentation process of electronic waste (e-waste), the metals can be separated without fine grinding. This research considers the applicability of high voltage pulse fragmentation for LED lamps. Eight different types of LED lamps were processed through the SELFRAG unit at varying pulses to study metal liberation. The product obtained was characterized for metal liberation, metal grades, and liberation analysis. The specific energy consumption for this size reduction process was also monitored. INTRODUCTION Lamps and bulbs are the most commonly used electrical products in homes, offices, industrial operations, and streets. According to Energy Star research (2006), an average US household has more than 40 sockets for light bulbs and consumes approximately 2100kWh every year for lighting. The development in lamp technology has pushed the boundary for newer products. The LED lamps have been taking over the market from the incandescent bulbs and compact fluorescent lamps (CFL). According to the US Department of Energy (2012) and myLEDlight.com (2007), LED lamps have several benefits over other lamps. LEDs produce light hemi-spherically, which increases their efficiency in directional light emission. It has higher breakage resistance from vibration or transportation. LED lamps use up to 90% less power than incandescent bulbs thus making them highly energy efficient; They have a longer lifespan, lasting 10 times longer than a CFL and 133 times longer than the traditional incandescent bulb. Because of all the benefits, Smallwood (2014) suggested that the market of LED lamps will grow to $12.2 billion by 2018."

Jan 1, 2018

By Bertil I. Pålsson

The most common REE containing mineral that is worked today is bastnäsite. It means that mineral processes are adapted to it and that the metallurgical separation techniques for winning of individual REE are adapted to bastnäsite concentrates. For all other deposit types, suitable mineral processing methods and separation technologies need to be adapted and/or developed. Preliminary mineralogical analyses indicate that slightly less than half of the REE in the tailings dumps at LKAB/Kiruna are associated to apatite. The rest is in the minerals monazite (maybe associated to apatite) and allanite. At least allanite is probably not floatable with reagents commonly used for apatite. Mass and element distributions for the tailings sand reveal that very little apatite is present above 300 µm, and that approx. 30 % is below 20 µm. REE does not follow P2O5 completely and are also present in coarser fractions. Flotation results show that the best condition for both apatite and REE winning is pH 9, high collector addition and low dosage of water glass. Under these conditions, the lab-scale flotation gives an apatite concentrate with at least 30 % P2O5 at 70 % recovery. REE follows apatite in the cleaner steps but only partly. Its recovery is approx. half compared with apatite. The reason for the low REE recovery is likely to be that REE to a large extent is trapped in non-winnable minerals, especially allanite. The REE grades in the concentrate are expected to be in the range 3000 ? 4500 g/ton. Keywords: flotation, REE, apatite, monazite, allanite

Sep 1, 2012