Search Documents

By M. X. Jia

This paper discusses two mineralogy characteristics that may affect the flotation of sulfide ore. The first one, process mineralogy study on a Cu-Ni sulfide ore shows that valleriite and tochilinite are incline to form on chalcopyrite, pyrrhotite and serpentine surface, and the further guess is that the formation of valleriite and tochilinite may also causes the serpentine transform to talc, so the serpentine surface is a phase of talc or a transition phase from serpentine to talc and this enhances the flotability of the gangue minerals. The second discussion on the flotation behavior of the sulfide minerals from the point of view of the mineral semiconductor character.

Jan 1, 2014

By M. Saghaeian, R. Hejazi, L. Hosseini

The specific surface area (Blain value) of iron ore concentrate entering the pelletizing plant is one of the characteristics most effective on the overall performance of the plant such as producing harder pellets, decreasing additives consumption, and decreasing energy consumption. Therefore, preparing the feed entering pelletizing plant is required. The iron concentrate entering Ardakan pelletizing plant located in Yazd province, Iran bears relatively low Blain value (approx. 1600 cm2/g) which necessitates one stage of regrinding so as to increase the Blain value to more than 1800 cm2/g. Studies were conducted and results showed that HPGR is the best regrinding equipment for increasing specific surface area. Conducting pilot plant tests on the concentrate sample revealed that specific throughput is 181 to 263 ts/hm3 and specific energy consumption is 1.6kWh to 2.2 kWh. Pilot tests also showed that one stage of grinding results in 407 cm2/g to 553 cm2/g increase in specific surface area. Based on these results, diameter of rolls, length of rolls, power consumption and grinding force were calculated to be 1.3 m, 0.9 m, 1276 kW and 13800 kN, respectively. Therefore, an HPGR with a roll diameter of 1.52 m, roll width of 1.1 m, power of 1660 kWh and a capacity of 500 t/h has been selected and implemented in Ardakan pelletizing plant. Industrial performance of HPGR and its effects on the plant study results show that limestone and bentonite consumption has reduced about 60% and 30%, respectively. Total Fe of the final pellet has increased from 65.5-65.7% to 66.2%. Cold compressive strength (CCS) and porosity of final pellets are approximately 292 kg/pl and 20.4, which are in the acceptable range.

Jan 1, 2014

By Aziza A. Yousef, Suzan S. Ibrahim, Mahmoud A. Arafa, Mohamed A. Abdel Khalek

Due to the shortage of fresh water in the Middle East, seawater has been used as an alternative in flotation beneficiation. The flotation process requires about 7 m3 of water/mt ore. This article aims to study the effect of seawater cations and anions on the flotation. Natural pure francolite, calcite, dolomite and quartz were characterized by chemical, thermal and x-ray diffraction analyses, surface area, solubility and zeta potential. Synthetic seawater was prepared with the major chemical composition similar to natural seawater as follow; 2.45% NaCl, 0.52% MgCl2, 0.41% Na2SO4, 0.116% CaCl2 and 0.07% KCl. Also, natural seawater was used in application. The point zero of charge was estimated at pH 6.5, 7.8, 9.2 and 2.2 for francolite, calcite, dolomite and quartz, respectively. Calcium ions were released from the three minerals with Mg2+ and P2O5 3– released from dolomite and phosphate, respectively. The adsorption of collector, zeta-potential and floatability of pure minerals were studied. The effect of individual cations and anions predominant in seawater are studied on individual mineral or group. The troublesome Ca2+ and Mg2+ ions should be controlled by soda ash addition. Sodium silicate improved the selectivity of mineral mixtures and natural ore. At optimum conditions the calcareous phosphate ore yielded a concentrate of 34% P2O5, at 83% recovery with 0.61% MgO, from an ore assaying 25.3% P2O5 and 9.4% MgO. To minimize the Clcontent, fresh water of about 0.5 m3 /t was used and the Cl- decreased to about 0.09 %

Jan 1, 2003

By F. Ngoroma

Concentrators processing PGM bearing ores make use of polysaccharide depressants to reduce the recovery of the undesired naturally floatable gangue minerals, mainly silicates, present in the ore. Recent work has shown that high depressant dosages can completely depress naturally floatable gangue and thus prevent it from reporting to the concentrate. These high depressant dosages can, however, have a negative effect on the recovery of valuable minerals present in the ore by reducing the stability of the froth. In order to counterbalance the effects of depressant addition, frothers are added. It is, however, preferable to maintain independent control over bubble size and froth stability which is difficult to achieve with only one frother. An alternative strategy is, to use a blend of frothers, e.g. a weaker frother in combination with a stronger frother. Such a system allows an additional degree of freedom: changing the ratio of the two frothers, that would provide more independent control of bubble size and froth stability. This study demonstrates, through the use of batch flotation tests, how blending low molecular weight alcohols with commercially available frothers impact the solids and water recovery, as well as the valuable mineral recovery and concentrate grade in different PGM ores. Higher water and solids recoveries together with higher valuable mineral recoveries (>90% copper and >70% nickel) were obtained from tests using frother blends.

Sep 1, 2012

By G. X. Du

Improving reaction effectiveness of asbestos tailings and acid is main means to increase the productivity of magnesium hydroxide and amorphous silica and to reduce production costs. In this paper, the process optimization of acid-leaching reaction process of asbestos tailings is reported. Through the orthogonal experiments of four influence factors, such as acid consumption, reaction temperature, reaction time and initial acid concentration in the leaching reaction. The experiment results indicated that the optimal process parameters were as follows: reaction temperature was 95?, reaction time was 1.5h, acid consumption was 218.9g hydrochloric acid(37%) per 100g asbestos tailings and initial acid concentration was about 25%. The influence significance sequence of the four factors was as follows: reaction temperature > reaction time > mass concentration of hydrochloric acid > hydrochloric acid consumption. Under the optimum process conditions, the leaching rate of MgO was 97.3%, total iron 98.15% and Al2O3 57.9%.

Jan 1, 2014

By G. Demi

The biggest chromium mineral processing plant in Albania is Bulqiza plant. It has been in operation for more than 20 years, treating low-grade chromium ores grade 20 ? 26 % Cr2O3 and producing chromium concentrates grade 48 ? 50 % Cr2O3. About 2 million tons of tailings with 13 % Cr2O3 content are stocked in a dam close to the plant. Mineral processing of low-grade chromium ores with less than 16% Cr2O3 content is unprofitable because the mining expenses are high comparing with the current market prices of chromium concentrate. Recycle and enrichment of existing tailings is profitable, because there are no underground mining expenses in this case and because that this kind of raw material does not need expenses operation of crushing and grinding. The existing plant is in operation for more than 8 years treating existing tailings as raw material. Grade of concentrate in the value 40 % Cr2O3 and Cr2O3 recovery in the value 30-35% in the plant are considered low. The main reason of low concentrate grade and recovery is high content of particles under 100 microns, the slimes, in raw material. In the paper is described the study carried out to improve enrichment of the tailings, as well as analyses of existing process, raw material and products. It is concluded that majority of lost is present in the slimes which are not separated in existing spiral separators and shaking tables. Basing in the study is composed the new flow sheet of recycling and concentration of the tailings to produce chromium concentrate grade 41 ? 42 % Cr2O3 and recovery 60 %, decreasing in this way the concentrate production cost two times. In the paper are presented the tests and results of concentration of particle size fraction under 100 microns, using gravimetric, magnetic and flotation methods, as well as equipment and machines suitable for slimes treatment and concentration.

Sep 1, 2012

In this study, selective flocculating of diaspore using anion macromolecular reagent as flocculant was tested to separate diaspore from alum-silicate minerals. Firstly, the effect of pH on settling behavior of diaspore and kaolinite dispersions has been investigated. The results show that the maximum settling speed of diaspore and kaolinite appeared re-spectively at pH7 and pH3.33 which is close to the point of zero charge (PZC) of diaspore (6.8) and kaolinite(3.5). This result is in well agreement with the double electric layer theory. Secondly, the settling behavior of diaspore and kaolinite particles in different anion flocculant solution have been researched. The results indicate that flocculant solution concentration significantly affect the selectivity and the flocculating performance of anion molecular. In high concentration solution, both diaspore and kaolinite have faster settling rate compared to blank solution. How-ever, in low concentration solution, the anion macromolecular can enhance the settling rate of diaspore remarkably but has no apparent effect on the settling rate of kaolinite. This result suggests that the tested anion flocculant is a promising reagent for de-silica of diasporic bauxite. Lastly, FTIR method was employed to probe the adsorption mechanism of flocculant on diaspore and kaolinite. The results reveal that there are anion flocculant characteristic bands on the spectra of diaspore but no obvious characteristic bands of flocculant on the FTIR spectrum of kaolinite. This result is in good correspondence with settling test.

Jan 1, 2014

By E. Hulthén

Cone crushers are used in the mineral, mining, and aggregate industry for fragmentation of rock materials. Control systems for cone crusher settings are widely used to compensate for wear and to protect the machines. The eccentric speed in a cone crusher affects the number of compressions the material is exposed to and thus the particle size distribution of the product. Eccentric speed also affects crusher capacity. However, the speed of the crusher is mostly fixed, because speed changes must be made by shifting pulleys, a process which is quite time-consuming. By applying a frequency converter, which has decreased in cost during recent years, it has become possible to adjust the speed continuously. By also applying mass-flow sensors to the process, the crusher can be run optimally to yield the most sellable products in a given moment. Existing systems normally only protect the machine. The sensors can be mass-flow meters, e.g., conveyor-belt scales. To analyze data from the process and calculate the appropriate value for the speed, an algorithm has been developed. The developed algorithm was tested and evolved at a crushing plant for aggregates that produces around 350 kton a year. The algorithm was implemented in a computer that could communicate with the frequency controller, retrieve data from four mass-flow meters, and also interact with the opera-tor. The computer was reachable over the Internet for the researchers at Chalmers and the algorithm was tuned and improved on-line. The result is a crushing stage that consistently and maximally produces the most desirable product. The performance (yield of required products) increased by 4%. As a bonus, the lifetime of the mantles increased 27% on the evaluated crusher.

Jan 1, 2014

By Jianjun Tian, Changjiu Zhang, Chunmin Wang

Two lines of single stage autogenous milling circuits have been installed and commissioned as the primary grinding process for the Sino Iron project where magnetite ore is treated to produce iron concentrate via magnetic separation. Various challenges were encountered during the commissioning and ramp up stages which are discussed in the paper and include treating a highly competent ore in a closed circuit AG mill, operating the largest mills in the world and dealing with a number of engineering issues related to plant operability. Details of how these challenges were overcome are described as well as the observed operating characteristics of the mills and their optimisation through rigorous study, simulation and successful solution implementation. Further potential improvement opportunities are also discussed as part of the ongoing technical program at site.

Jan 1, 2014

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

"The morphology of pellet feed is known to influence several properties of iron ore pellets, including drop number, compression strength and reduction properties. The effect of grinding method on the particle size, specific surface area and particle shape of an iron ore concentrate has been studied. Grinding methods considered were ball mill and high pressure grinding rolls (HPGR). 5 different samples (Blaine= 1800, 1900, 2000, 2100 and 2200 cm2g-1) were used to compare the size, shape and specific surface of particles for each grinding methods. Particle size was meticulously examined by sieve analysis, laser sizing and image analysis. In samples ground by ball mill, it has been observed that the fraction of particles <10µm increases from 39% to 46% as the Blaine number increases from 1800 to 2200 cm2g-1. For HPGR samples, corresponding figures are 41% and 49% respectively. It is evident that for samples ground by HPGR, the fraction of fine particles is higher than that of those ground in the ball mill. To measure the specific surface area of particles, Blaine and BET were used. A higher real surface area was observed from HPGR treatment in comparison to ball mill grinding, provided by a higher porosity, cracks, roughness and new surfaces. Shape factor of particles was determined using three descriptors: circularity, roughness, and aspect ratio. It was also observed that particles produced by HPGR were more elongated, less circular, and rougher than those processed by the ball mill. 1. INTRODUCTION Particle size and shape are important parameters that can significantly affect mineral processing plants and pelletizing plant performances (Brozek and Surowiak, 2007). It has also been proposed that green pellet quality is directly related to the amount of fine particles in a pelletizing plant (Dwarapudi et al., 2008; Umadevi et al., 2008; Gul et al, 2014; Van der Meer, 2015). Particle size distribution and specific surface area (SSA) are also key factors that can control the quality of green and fired pellets. Processing circuits generally reduce the fines fraction to lower than the required specific surface area (SSA). It is therefore necessary to regrind concentrates to produce suitable pellet feed for further treatment in the balling and firing steps [1, 2]. Two main methods are used for re-grinding of concentrate; high pressure grinding rolls (HPGR) and ball mill. Given the different forces used to reduce size in these methods, it is expected the shape of particles will be different (Pourghahramani and Forssberg, 2005)."

Jan 1, 2018

By Jyotirmoy Sarma

The surface-active agent, like sodium humate, in the present systems produces a very stable suspension. Saline water up to 15% is used as a flocculating agent for recovery of water from the dispersed phase containing 1% solid. The recovered water in the presence of humate at different concentrations (0.05-0.2%) and at pH 8 also produces a stable dispersed phase of iron ore fines and tailings. The beneficiation techniques adopted in the present systems can increase ~ 2-3% iron value in the concentrate of iron ore fine, however, for tailings the increase in iron value is not observed. Keywords: beneficiation, flocculation, iron ore fines, tailings, saline water, surface-active agent

Sep 1, 2012

By R. S. C. Smart

Surface chemical factors, including the balance of hydrophobic (e.g. collectors) and hydrophilic (e.g. oxidation products, precipitates) species, are major control determinants in flotation rates of specific minerals and therefore grade and recovery. There are a number of challenges involved with the surface analysis of different mineral phases from process streams in a flotation facility. The first is to collect samples that are representative of the process and retain their surface chemistry prior to introduction into the instrument. The second challenge in studying the surface chemistry of specific minerals is to find reliable methods of mineral phase recognition. In surface analysis of mineral particles, confident mineral selection can be difficult with many multi-metal minerals and with precipitated, adsorbed, reacted and contaminant species in the outermost molecular layers. The third challenge is to provide a statistical surface analysis of multiple grains of the same mineral. Methods to achieve these aims are described. Principal component analysis (PCA) of ToF-SIMS data provides improvement in phase recognition, particle selection and associated variations in surface species. Specific examples from both lab and plant operations, demonstrate that this technique can be utilized to differentiate surface chemical factors promoting (hydrophobic species) or inhibiting (hydrophilic species) flotation. A study of copper ion transfer (inadvertent activation) from chalcopyrite to pyrite and sphalerite clearly identified a statistical difference in copper intensities between the sphalerite and pyrite phases corresponding to their flotation response. The PCA analysis applied to concentrate and tails samples collected from the Inco Matte Concentrator demonstrated extensive CuOH and NiOH transfer between chalcocite and heazlewoodite minerals. The statistical analysis has been able to identify mechanisms controlling recovery and selectivity. High intensity conditioning (HIC) tests in which sphalerite was separated from a complex sulfide ore gave a 5% increase in the overall Zn recovery. The PCA/ToF-SIMS statistical analysis revealed the discriminating depressant action of adherent aluminosilicate (gangue) fine particles and adsorbed ions on the surface of sphalerite grains. HIC conditioning resulted in the removal of these gangue fines improving surface collector attachment efficiency.

Jan 1, 2014

By Sunil K. Tripathy

Particle characteristics such as size, density, liberation and magnetic susceptibility play vital role in magnetic separation technique. To understand the performance of magnetic separation process for chromite beneficiation industry, particle characteristics need to be analysed. However, to date, this has been an expensive and time consuming task, thus only minimal amounts of this type of data are available in the literature. Several new methods are being developed, that will produce the required mineralogical and liberation data to provide processing information rapidly and inexpensively. Among these, QEMSCAN is a unique and advanced characterisation equipment used for liberation analysis for different ore whereas S.G. Franz Isodynamic Separator for determining the magnetic susceptibility. In Indian chromite deposits, the content of iron bearing minerals in the ore is typical which controls the Cr:Fe ratio in the product while treating in gravity based beneficiation plant. In the present investigation, detailed characterisation of two distinct chromite ore samples from Sukinda chromite deposit, India, was investigated which includes advanced mineral characterisation using QEMSCANand magnetic susceptibility measurement by using Frantz Isodynamic separator, etc.. Presence of haematite and gibbsite along with chromite mineral were identified as major gangue minerals in the high grade ore from XRD pattern whereas Goethite, Quartz, Haematite, Kaolinite, Ringwoodite identified in the low grade ore. The mass magnetic susceptibility of low grade ore is very high 5.2 cm3/g compared to 2.7 cm3/g for high grade ore, due to the presence of abundant quantity of iron bearing minerals. Subsequently, these two types of ore were subjected for magnetic separation for improving Cr:Fe ratio by using different magnetic separators viz. induced roll magnetic separator, wet high intensity magnetic separator, rare earth roll magnetic separator, rare earth drum magnetic separator. The results of magnetic separation studies indicated that, Cr: Fe ratio of the chromite ores can be improved to 3.99 and 1.97 from the feed assaying 3.09 and 1.29 respectively. Studies on rare earth roll magnetic separator indicated that both the ores were upgraded to a maximum Cr:Fe ratio level at optimised condition. Keywords: characterization, QEMSCAN, magnetic separation, rare earth roll magnetic separator, industrial mineral, chromite

Sep 1, 2012

By Matheus Tocchini, Henrique Kahn, Juliana Antoniassi, Carina Ulsen, Eldon Masini

"Sand and gravel are the second and third largest minerals in production in Brazil, and this is increasing noticeably. The extraction of natural sand from river beds is increasingly restricted and most of the sand used in large cities comes in from more than 150 km away, resulting in high transportation costs. As a result, it has become more common to use crushed rock as artificial sand. The main difficulties in this process are controlling the shape of the particles and the content of deleterious materials, such as mica. Within this situation, this paper presents an alternative to using artificial sand for concrete use. Our procedure involves the following steps: a) sampling sand from different production days, b) characterizing the bulk sample by particle size and shape distribution, chemical composition by X ray fluorescence and mineralogical composition by X ray diffraction, c) removing fine grains by air classifier, d) performing intensive attrition with high pressure washing and e) characterizing products. The results demonstrated that this sample contains a huge proportion of fine grains and a notable content of mica, which is distributed along all sieve fractions. The presence of mica makes the use of sand in concrete unfeasible, moreover scanning electron microscopy analysis demonstrated that this phylossilicate is finely grained and associated with coarse fractions. Thus, the removal of fine fractions made possible a partial reduction in mica content. Furthermore, intensive attrition demonstrated that the procedure was efficient to remove most of the mica while also reducing sharp edges, which improved the shape of these particles."

Jan 1, 2014

By W. Y. Gao

Diaojuntai Concentrator adopts a process of low intensity and high intensity magnetic separation and anionic reverse flotation, with all the concentrate from magnetic separation being treated by re-verse flotation to obtain a qualified final concentrate. The high reagent cost and energy consumption of the reverse flotation have led to a high concentrate cost. The test research on reducing the feed to the reverse flotation was therefore carried out. Based on the study of the properties of the ore sample, the concentrate of low intensity magnetic separation was screened at 0.076 mm and the undersize fraction was concentrated by concentrator with gravity and magnetic field. The results show that a qualified concentrate can be obtained at various rising current rate, pulsating current and power-on style, with the operation rate over 85%. The extraction of some part of qualified concentrate from the concentrate of low intensity magnetic separation by magnetic separation can reduce the feed to the reverse flotation by about 35% so as to reduce the production cost of concentrate.

Jan 1, 2014

By A. T. Adema

The cohesive zone, where the ore fed into the blast furnace softens and melts, is critical to the blast furnace performance and stability due to its influence on the gas and solid flow. This paper de-scribes a project for the development of a process model to predict the cohesive zone properties and the results of its first step; the solid flow model. The process model is expected to describe a realistic solid burden flow and the formation of the cohesive zone, its shape, location, structure, permeability, and in particular the mineralogical changes within the cohesive zone. This will be achieved using various simulation and computing tools: a combination of the Discrete Element Method (DEM) and Computational Fluid Dynamics (CFD), the DEM?CFD hybrid approach, together with models for the thermodynamics and reaction kinetics. The key benefits of the hybrid approach lie in the coupling of the continuous phase and the discrete particles, and the possibility of introducing thermodynamics and reaction kinetics into the system in a more realistic manner. Two DEM simulations are presented for a small scale blast furnace to investigate the influence of non-spherical particles on the solid flow. This influence can be observed from a more even solid flow pattern and a reduced deadman size. The results indicate the requirement to include non- spherical particles in a blast furnace simulation to achieve a realistic solid flow.

Jan 1, 2014

By Christopher M. Rule, Martyn P. Hay

"A methodology was developed in the mid-1980’s to predict plant performance from standard laboratory flotation tests. The methodology incorporates a flotation simulation program “SUPASIM” which translates flotation performance from bench-scale tests to full-scale plant. The technique is based on a simple, empirical kinetics model, and is tailored for use by the practical metallurgist. Kelsall’s unmodified equation incorporating two rate terms describing slow and fast floating components is used as the basis of the method. The flotation behaviour of an ore is described by a set of numbers, which can be compared in the evaluation of ore types, mineralogy and operating conditions. In so doing a precise relationship is developed between metallurgical performance in terms of grade and recovery and flotation kinetics.To date the performance of more than 20 flotation plants has been predicted, encompassing copper, lead, zinc, nickel, phosphate, pyrite, graphite, cassiterite, platinum and various slags. In three cases, plants have treated more than one type of ore. The method has successfully been used to predict and design four flotation plants using data generated from bench-scale laboratory flotation testwork. All have since been commissioned, and have performed as predicted. In the last year alone it has been used to drive flowsheet development for at least seven new plants in South Africa and the Americas. It is also being used to assist in the optimisation of existing operating plants."

Jan 1, 2003

By P. Gao, J. W. Yu

"Pre-concentration is a necessary step for upgrading low-grade iron ores, and its aim is to remove gangue minerals for improving efficiency of downstream separation process. The most important pre-concentration technique for iron ores, including hematite, siderite and limonite, is magnetic separation based on the appreciable differences between the desired iron minerals and gangue minerals in magnetic susceptibility. In this paper, the separation efficiency of one-stage low-intensity magnetic roughing combined with two-stage high-gradient magnetic scavenging for the pre-concentration of a low-grade hematite from Donganshan was investigated. It is a BIF type of ore containing hematite, magnetite and a bit of siderite, and an average content of Fe is about 34.6%. The effects of grinding fineness and magnetic field intensity for scavenging I and II were studied and optimized. The results showed that a magnetic preconcentrate assaying 42.7% with a recovery of 95.4% was obtained under the conditions of ore grinding fineness of -74 µm 70%, magnetic field intensity of 300 mT and 800 mT for scavenging I and II, respectively. Over 20% of the feed was rejected as the final tailings assaying 6.4% Fe. Meanwhile, the XRD, iron chemical phase and SEM analyses of different stage products revealed that hematite, magnetite and siderite could be recovered successfully by magnetic separation. However, some ultra-fine hematite particles (-10 µm) were difficult to be captured by magnet, and lost in the final tailing, resulting in lower iron recovery.INTRODUCTION Donganshan iron ore belongs to sedimentary-metamorphic iron formation called banded iron formation (BIF), which is formed in the Precambrian with a layered structure composed of ore bodies (Shen, 2012). Such type of iron deposit contains various iron-bearing minerals like hematite, magnetite, and siderite, suggesting it may be amenable to pre-concentration with magnetic separation. The pre-concentration process is effectively applied in recovering hematite, magnetite and siderite from iron ore, due to its benefits of further upgrading iron ore and improving separation efficiency. The most important pre-concentration technique for iron ore is magnetic separation, including low-intensity magnetic separation and high-gradient magnetic separation, based on the fact that there are appreciable differences between the desired hematite, magnetite or siderite and the gangue minerals in magnetic susceptibility."

Jan 1, 2018

By A. S. Choudhary

Most of the coal reserves in India are of drift origin and have very poor washability characteristics and a high level of near gravity materials. At least 30 new coal wash plants are expected to be set up in the next 5years.In such a scenario, adequate sampling followed by sink float test work for washability analysis becomes very critical for designing these new plants. For coal sampling purpose, stipulations of different standards are sometimes formidable and on the border of ?impracticality?; sometimes are self contradictory in terms of gross sample weight vis-a-vis minimum number of particles required in each size fraction and in each relative density fraction and also the minimum mass in the latter. Validation of the generated data is another important aspect of washability analysis. These issues can easily be addressed by using straight forward mathematical relationships, well known RR plots and by using simple MS Excel tool, etc.

Sep 1, 2012

By Shugang Hu

According to XRD, DTA and SEM detections, the hydration products of blast furnace slag (BFS) based cementing material SL, SLG. were studied in different age periods. The XRD analysis of cementing material SL hydration products showed that the composition of hydration products were mainly amorphous substances, few crystalline substances. Characteristic peak of ettringite hadn?t been found in the spectral line of DTA, and it hadn?t been found in the figures of SEM, either, which was accordant with the conclusion that the cementing performance of SL mainly coming from gel of hydrated calcium silicate (CSH) and hydrated calcium aluminate. However, the main hydration products of SLG are Aft, CSH, and AFm, which are similar to Portland cement. All results suggest that BFS is a suitable base material for cementation. Keywords: blast furnace slag, backfilling cementing material, hydration products, cementing performance

Sep 1, 2012