Search Documents

By B. Hosseini

Considering the subtractive trend of the sulfide and high-grade zinc ores in worldwide and also in Iran, Nowadays special attentions have been drawn to the extraction of zinc from its other resources such as low-grade oxide ores and secondary resources. Oxide ore of the eastern part of Mehdi-abad lead and zinc mine is silicate and has an average grade of 7% (with cut off grade of 4%). Main mineral of the Mehdi-abad ore is Hemimorphite and this mineral is associated with Goethite, Hematite, Ferrous Dolomite, and Manganese oxide mineral so that oxides of Iron, manganese and silica include almost 50% of the total ore. In this paper, the results obtained from the leaching kinetic study of the low-grade zinc oxide ore using Sulfuric acid are presented. The effects of particle size, reaction temperature, acid concentration, and solid percent on the dissolution rate have been investigated. The results obtained from the Taghochi approach showed that the zinc recovery is about 78% under the following optimized conditions: particle size: 106µm, leaching time: one hour, temperature: 45°C, acid concentration: 15% and solid percent: 15%. Kinetics study was revealed that zinc minerals leaching controlled by diffusion rate through the product layer during leaching time with the activation energy of 5 KJ/mol and compliance with the 1- (2/3. x) ? (1- x) 2/3 = k. t model. Keywords: leaching kinetics, kinetics models, sulfuric acid leaching, taguchi methods, low grade zinc ore, mehdi-abad mine

Sep 1, 2012

By S. Sarioglan

The bleaching of edible oils, industrial oils, and some chemicals may be achieved using natural and acid-activated clays. These materials remove impurities and pigments from the oils. In this work, a bentonite clay from Turkey (Somas bentonite) was activated with different concentration of H2SO4 and HCl at 70~90°C and 5~8 hours. Under these conditions several cations were removed from natural bentonite (Al, Mg, and Fe) and DTA-TGA, FT-IR curves of the solids obtained after acid treatment were examined. Treatment time and acid concentration increased the degree of destruction of the bentonite structure which was determined by ICP. Activated samples were tested in order to verify their capacity to bleach soybean oil and compared to standard commercial bleaching clays. The experimental results indicate that treated samples with H2SO4 have the same efficient in bleaching crude soybean oil with the standards and treated sample with HCl is more efficient in bleaching than the commercial products.

Jan 1, 2014

Nowadays, the more successful plants are those who have adopted effective and efficient strategies to optimise their plant operation. As the ?heart of the plant? could be viewed as the mil-ling/grinding area, one of the key steps in plant optimisation is, therefore, ensuring the mill is operating properly. In the past, when primary, secondary and tertiary crushers fed material directly to large ball mills, the energy efficiency of the concentrator was determined for the most part by the ball mill operation, whereas now the energy efficiency of a plant often rests largely on the semiau-togenous grinding (SAG) mill operation. As a result, mines have shifted their emphasis in optimization from ball mills to SAG mills. The grinding mill?s energy efficiency essentially depends on ore characteristics and the discharge rate of broken particles, which in turn depends on how efficiently the discharge pump (grate and pulp lifters) operates. The essential function of pulp lifter being to transport the broken material and slurry out of the mill, its design optimization therefore affects the discharge capacity (or mill throughput) of AG and SAG grinding mills. This paper will discuss how the optimised design of the pulp lifter/ discharger has helped to eliminate material transport issues such as flow-back and carry-over of slurry and pebbles to in-crease the energy efficiency of SAG mill using the actual operational data.

Jan 1, 2014

By P. Ying

An auxiliary system connected with SEM-EDX for rapid identification of mineral and rock sample has been developed. With the aid of a synthetic spectrum library created, using the compare and match techniques provided by INCA software in EDX the mineral or rock sample names for refer-ence can be given at the same time analyzed.

Jan 1, 2014

By I. Baltov

The Chelopech Mine, located in Central Bulgaria, is one of Europe?s largest underground copper- gold mines, currently mines and processes approximately one million tonnes of ore per year. Copper concentrates containing gold and silver with significant arsenic content are produced and sold on the world markets. The operation was acquired by Dundee Precious Metals in 2003. A modernization program for the Mine and Plant has since been in progress to increase both production and mechanical reliability, and also to optimize metallurgical recoveries. Since then, mine output and plant throughput have doubled, plant availabilities and utilization have increased significantly, and overall metallurgical performance for copper and gold improved. The paper presents the systematic approach for obtaining and analyzing data, communicating it, and making suggestions for changes to the technological parameters and flowsheet in order to maximize metal recoveries. These studies have correlated the ore characteristics (particle size distributions, metal assays, and Cu and Au mineralogical and phase analyses) with the actual plant performance (kinetics, recoveries, and throughput). Cu recovery by size has been calculated from the mineralogical analyses of feed, concentrate and tails, with the most significant losses being identified in terms of fraction and phase recoveries. This has provided the recommendations (some of them tested in plant) for changes in the grinding and flotation circuits.

Jan 1, 2014

By K. B. Venkatesh

In view of the importance of size reduction operations from the energy consumption point of view, during the past one hundred and fifty years a number of attempts have been made to develop a general energy-size relationship. However, to date it has not been possible to clearly define the scope of application of various laws proposed, though Bond law has been widely used with a moderate degree of success. It was, therefore, decided to carry out a thorough analysis of the batch ball mill grinding data available in the literature on several minerals that were ground under normal range of operating conditions. In particular, relationships proposed by Bond, Kapur, Voller and Morrell were examined in detail. It was found that the relationship proposed by Kapur in terms of the mean particle size provided a more accurate basis for estimation of energy. The value of the exponent of mean particle size in this relationship, a, is same as the exponent of the particle size in the expression for the grinding rate parameter: ki = Axia, provided the particle size distribution range corresponds to the self-similar or self-preserving regime. In this regime, mean particle size is proportional to the 80 percent passing size and size modulus. From the practical application point of view, it was possible to describe the variation of µ1 over limited, but significantly broad size range, using a constant value of a. Thus, by carrying out a few batches, grinding experiments over the size distribution range corresponding to the contents of the production mill, the applicable value of a can be determined. Keywords: energy-size relationship, ball mill, mean particle size, self-similar size distribution regime

Sep 1, 2012

By Ashok Kumar, Subhadra Sen Dr. Rashmi Kumari, D. P. Chakraborty, Ajay kumar Gupta

The blast furnace coke quality depends on the characteristics of coal blend, pre-carbonization techniques adopted such as stamping, vibro-compaction etc., and coking conditions. Of the above, coal blend plays a significant role in the production of quality coke. Furthermore, the quality of the blend depends on the quality of individual coals and their interaction making up the blend. During transportation and stockpiling, coal is in contact with air for periods of time that sometimes may exceed several months. During this time, reaction with oxygen in the presence of water, sunlight and possibly elevated temperatures may take place. The resulting weathered coal suffers some alteration in its technological properties, which in turn affects coke quality for Blast Furnace operation adversely. In this work, two coals belong two prime hard coking and hard coking categories, namely Illawarra & Tahmoor, were selected and kept in a separate stock pile for a period of 120 days. These coals were characterized in terms of proximate, rheological & petrography properties at a regular frequency. This report summarizes the impact of weathering on the coking behaviour of these two coals in terms of properties as mentioned above. However, the rate of loss depends on coal rank and storage conditions. This has been seen through this study that the loss depends on coal rank and storage conditions. Deterioration of rheological and petrographic properties were seen higher for low-rank coals, like in this study Tahmoor, which is a low rank coal, compared to Illawarra showed higher degree of coking property degradation within the same time period under identical environmental conditions. Low-rank coal deteriorates at a faster rate because low-rank coal is dominated by free radicals that easily react with oxygen, resulting in the creation of various carbonyl groups and weathered vitrinite. Based on the results obtained in this study, size of stock piles for different qualities of coals to be maintained, at a specific time, can be determined and recommended, so that target coke quality is always achieved.

Jan 1, 2018

By Jing Zhou

In view of the state of the long time use of sodium cyanide in lead-zinc-sulfur-silver multimetallic ore production, we propose alternative reagents system through experimental research. The experiment first used TJ, sodium sulfide to adjust the flotation pulp, after that, zinc sulfate, sodium sulfite was added to low alkaline pulp to inhibiting zinc sulfur mineral and adapted MB, 25# aerofloat and diethyl dithiocarbamate combination collectors to float lead minerals. The obtained test index is as follows: lead concentrate recovery rate of small scale test was increased by 5 to 10%, the recovery rates of gold and silver in lead concentrate were increased by 7% and 11% respectively; the industrial test is conducted under the condition that the total grade of lead and zinc content in raw ore decreased by 4.81%, the total recovery rate of lead and zinc increased by 7%, recovery rates of gold and silver in lead concentrate were increased by 7.62% and 9.65% respectively. So it successfully realizes the target to replace the sodium cyanide, using low-alkaline non-toxic reagents system in mineral processing practice of three kinds of complex lead-zinc-sulfur ore of this mine. Keywords: refractory lead-zinc-sulfur ore, depressant, non-cyanide flotation

Sep 1, 2012

By Vladimir G. Kochnev

"Autogenous and semi-autogenous grinding (AG and SAG) have been considered a step forward in comparison to conventional grinding circuits with several stages of crushing and using ball (and/or rod) grinding mills. However, existing AG and SAG technologies still can be improved and have an immense potential from the viewpoint of economic benefits.Experience gained by the Technics & Technologies of Disintegration Ltd. (TTD) in the research of grinding processes shows that comminution in AG and SAG mills can be performed in a more effective way. The company’s approach comprises the following elements:- Novel mill design- New liners and lifters- Novel discharge grid design- Technique of treating material of critical particle sizeA novel mill of the cantilever type capable to operate in the AG and SAG mode has been developed. The cantilevertype mill has a high diameter to length ratio, which dramatically increases the throughput rate, and is characterised by high reliability, fast installation and low capital and operating costs.Tests of the new heel-shaped liners, originally aimed at improving the intact condition of diamond, indicated that they play an important role in the grinding process. Tests performed by TTD jointly with ALROSA, MINTEK and Anglo-American Corporation, demonstrated that the heelshaped liners provided the increase in the throughput rate varying from 30 to 80 % and the decrease in power consumption in the range 30-55 % for grinding of kimberlite and platinum-containing ores.Investigation of the influence of the main grid parameters on the efficiency of grinding led TTD to a special design of a mill discharge grid, with a radial location of openings, the slot width varying from the periphery to the centre and the grid surface provided with “heels”. The design allows one to control the particle size distribution of the ground product without affecting the grid throughput rate."

Jan 1, 2003

By D. Y. Liang

Rare metal ores have those features of high industrial value and bad performance in ore separation. Most of rare metals ores are with low grade of valuable components, rareness of useful minerals, complicated combination of associated minerals and high difficulty in separation and enrichment of minerals. For those single (Ta, Nb) or (Ta, Nb, Sn) ore occurred in granite and pegmatite, the ways of gravity separation and magneto electric separation to concentrate (Ta, Nb) minerals are adopted. There are many mines being explored successfully both at home and aboard. While, for complex (Nb-Zr-REE) ores associated with Be and Ti minerals, they are commonly considered as rich rare metals ore but more difficult to process. One of rare metals mine in Inner Mongolia has the features as with large reserves and high grade of columbium and zirconium and accompanies with REE and beryllium, therefore with significant industrial value. After the utilization of research method of process mineralogy, detailed mineralogy research has been made on the rare metals ore. The test results show that there are abroad isomorphism replacements among such elements, such as Ti, Mn, Fe, Nb and Ta, between Be and REE in metallic oxide minerals of that ore, which makes the mineral composition of that ore extremely complicated. This research identifies clearly the mineral composition, and investigate at the technological property and the occurrence of those elements as Nb, Zr, Be and REE in the rare metal ore. The achievements of this research provide important mineralogy basis for ore dressing research of refractory rare metallic ores.

Jan 1, 2014

By U. Ulusoy

Surface roughness and acuteness are known as the two of the main properties of the particle morphology affecting the behavior of the powders in the process. Since the techniques used for the morphological characterization of powders by 2-dimensional microscopic measurement from the polished sections that have some disadvantages, the 3-dimensional analysis has often relied on measurements of particle morphology. A review of literature data was presented for high-grade barite and pyrite particles ground by ball and autogenous mills to determine the morphological properties using a new 3-D approach based on BET nitrogen gas adsorption and Permaran methods. Micromeritics Flowsorb II 2300 instrument which employs BET nitrogen adsorption technique was used for the specific surface area measurements and the roughness of the particles. Permaran (manufactured by Outokumpu Oy) was used for the measurements of airflow resistance of powder samples for the acuteness. Spherical glass beads were used as reference sample for the acuteness measurements. The obtained parameters, which are surface roughness and acuteness, were corre-lated with the floatability performance of those mineral particles. The flotation performances of those particles ground in different mills (ball and autogenous) were also evaluated by a Hallimond tube. The results showed that lower roughness and acuteness values caused higher flotation recoveries for both barite and pyrite particles that were tested independently in different type of the mills. In other words; particles with smooth surfaces resulted in better floatability for barite and pyrite minerals studied.

Jan 1, 2014

Under the sponsorship of the U.S. Department of Energy, a project was completed in 2005, which studied the use of a special pneumatic capsule pipeline (PCP) system, driven by linear induction motor (LIM), for transporting minerals and/or mine wastes. In this study, the pipeline is a rectangular tube of 1m × 1m cross section. The capsules are similar to railroad cars running on small rails imbedded in the tube. A LIM is placed AT the entrance of the tube to transfer power electro-magnetically from the LIM to capsules. The capsules going through the LIM, propelled by the electromagnetic field generated by the LIM, move faster than the air and hence impart energy into the airflow. This in turn pushes the capsules in the tube forward. When the tube is long (say longer than 10 km), additional LIMs may be needed along the tube to serve as booster pumps. An advantage of using LIMs instead of blowers as used in ordinary PCPs is that capsules can pass through the LIMs unhindered. This enables the use of booster pumps for long tubes. It also enables PCP to achieve much higher cargo throughput than that of PCPs using blowers, thereby reducing unit cost ($ per ton-km). Advantages of using capsules with steel wheels running on steel rails in the tubes including: (1) contact friction is only about one-fifth of that using rubber tires, thereby conserving energy, (2) capsules can run at a much higher speed than those using rubber tires without overheating and damaging the tires, and (3) rails make capsule motion control simple; they restrict lateral movement of capsules, and make branching easy-by using standard rail crossing equipment. This advanced PCP system combines the advantages of LIM with the advantages of rails, resulting in a super-efficient tube system having throughputs an order of magnitude greater than that of conventional PCPs, and having an energy efficiency better than railroad transport. Analysis shows that the system is highly cost-effective when throughput is high-at least 5 million tons per year. The system is most suitable for long-distance transportation of minerals (including coal and flyash) and wastes (including both mine wastes and municipal solid waste).

Jan 1, 2014

By S. K. Kawatra, T. C. Eisele

"Coal-fired electrical power generation plants produce 56% of all the electricity in the U.S., burning approximately 860 million tons of coal annually. This results in the production of 58 million tons of fly-ash; 19 million tons of bottom ash and boiler slag, and 23 million tons of desulfurization sludge.s annually. These are a considerable disposal problem, and it would therefore be very valuable to be able to sell these residues and by-products as useful materials, rather than paying to dispose of them in landfills. However, utilization rates are currently very low, below 32% even for the most thoroughly commercialized combustion byproduct (fly-ash). This poor utilization rate is a result of the high impurity content of combustion byproducts, which makes them unsuitable for existing markets.Mineral processing techniques are useful for upgrading and utilizing combustion by-products. Fly-ash can be processed to remove unburned carbon, or utilized as a binder component in ore pelletization and agglomeration processes; bottom ash can be processed to produce certain aggregate grades; CO2 emissions can be sequestered using modified leaching techniques; and many scrubber sludge’s require processing before they can be used for producing gypsum products.The experiments described in this paper were carried out to study the application of mineral processing techniques to upgrading combustion by-products, particularly flue-gas scrubber sludge. A process was developed for upgrading unoxidized Flue-Gas Desulfurization (FGD) sludge’s by removing the primary impurity (unreacted limestone). A combination of hydrocycloning followed by froth flotation reduced the limestone concentration to as little as 1.7%, while recovering 66% of the sludge weight as a clean product. The recovered limestone was sufficiently concentrated that it could be recycled to the scrubber for more complete utilization."

Jan 1, 2003

The multiphase reactive flow in process equipments, e.g., fluidized beds, involves complex coupling among flow, heat/mass transfer and reaction kinetics over scales ranging from molecules, sub-particle eddies up to equipments. Conventional two-fluid model (TFM) ignores the effects of meso-scale structures, and hence is not suitable for describing the intrinsically multi-scale heterogeneity within multiphase systems. To be consistent with the meso-scale structures, we proposed a structure-dependent multi-fluid model (SFM), and closed its drag force by invoking the stability condition defined in the energy-minimization multi-scale (EMMS) model. The SFM reduces to the conventional TFM if homogeneous distribution is assumed within each grid, and reverts to the original EMMS model if it is used to describe steady state, global behavior of a fluidized bed. The multi-scale computational fluid dynamics (CFD), which is characterized by coupling of TFM and EMMS drag coefficient, can then be viewed as a simplified solution of the SFM. We demonstrate that the SFM significantly improves the accuracy and at the same time enables higher efficiency by allowing for much coarser grid used than in TFM. Recent application of it in 3D, full-loop, transient simulation of industrial processes, e.g., fluid catalytic cracking, coal combustion, gasification, kaolinite clay calcinations, shows its advantages in helping design and troubleshoot multiphase process equipments. Keywords: meso-scale, SFM, multiscale, CFD, simulation, structure, EMMS, multiphase

Sep 1, 2012

By Abhakumari

Effect of applied DC potentials on the bioleaching of a chalcopyrite concentrate in the presence of Acidithiobacillus ferrooxidans is discussed. Copper dissolution was the highest at an applied potential of +600mV (SCE), while all the dissolved copper got cathodically deposited at a negative potential of -600mV (SCE). Electrobioleaching at an applied potential of +600mV (SCE) was established at different pulp densities as a function of time. Effect of the magnitude of electrolytic currents on the activity and growth of bacterial cells was studied. Preadaptation of bacterial cells to the concentrate slurry and electrolytic growth conditions significantly enhanced copper dissolution. Electrochemical and biochemical mechanisms involved in electrobioleaching are illustrated with respect to oxidative dissolution and bio catalysis of anodic oxidation.

Sep 1, 2012

By W. H. Yong

The molybdenum ores currently utilized in China are mostly molybdenum sulfide ores, whereas oxidized molybdenum ores have not been exploited and utilized efficiently. The aim of this article is to study the applied mineralogy of an intergrown iron-molybdenum oxidized ore in order to provide a mineralogical basis for the ore beneficiation research. The ore occurred in a surface oxidized zone seam and contained 23.65% Fe2O3 and 1.58% Mo. Various characterization techniques were employed to study the chemical composition and mineral composition of the ore, the particle size distribution of the minerals in the ore, and the tex-ture and structure of the ore. The results showed that the iron-molybdenum ore occurred in a wet, soft and earthy state. The ore was composed mainly of several oxidized minerals and colloidal min-erals, including wulfenite, barite, limonite and quartz. Wulfenite was one of the major and stable components in the ore and occurred as a separate mineral. Wulfenite, barite and quartz were granu-lar minerals with particle size ranging from fine to coarse but mainly in the fine particle range. Li-monite showed a crust and honeycomb-like colloidal state and composed the framework in the ore for the formation of the other minerals. They filled the pores in the framework and the size of the pores affected the size of the minerals formed in the pores and hence the recovery of wulfenite in ore beneficiation. According to the applied mineralogical properties of the oxidized molybdenum ore, a promising ore beneficiation process was proposed as follow Magnetic separation should be carried out first to separate the magnetic iron minerals and then the molybdenum mineral will be recovered by gravity concentration or a combination process of gravity concentration and flotation, depending on the distribution of the molybdenum mineral in the product of the magnetic separation.

Jan 1, 2014

By M. Saghaeian, R. Hejazi, M. Farahani, M. Dehghani, A. Tohry

"Wet tailing dams of iron ore processing plants typically contain a significant amount of valuable minerals. In more recent years, due to the increase in iron’s prices and technological innovations, as well as the low energy consumption which required for processing of materials from tailings, dams can consider as potential valuable deposits. However, the production of iron concentrate from tailings is usually complicated where the high moisture content of the material, the high clay content and the presence of chemicals of processing such as flocculants, acids and flotation reagents, all make materials highly sticky which can be easily swollen. In the present paper, the optimization of operational parameters to recover ultrafine hematite iron ore from the wet tailings dams of the Chador-malu iron ore mine was investigated. The optimization of operational parameters, showed that with modification of the washing unit components for slurry making, the challenge of constraints from feeding the plant could be overcome. To decrease the magnetite content in the tail stream of the medium intensity magnetic separation (MIMS) and subsequently increase the efficiency, the orifice of the cleaner tail flow exit pipe was changed from 7 inches to 3 inch and yoke angle changed from 14 to 8 degrees. These changes increased mass yield by 3% and decreased the magnetite content in the final tailings to 1.2%. By recirculating the cleaner SLons of final tailings within the circuit, the solid percentage of the feed to rougher SLons decreased to around 15%, and as a result the matrices were not overloaded that easily, and mass yield increased to about 13% from 7%. All the above mentioned optimizations were achieved without significantly affecting the concentrate Fe grade."

Jan 1, 2018

By V. I. Lakshmanan

The growing concerns on process efficiency, escalating operating and capital costs along with environmental and social concerns of using conventional technology for extracting gold and titanium dioxide demand an in-depth understanding of the fundamentals and a broader understanding of the various process steps involved. This will allow development of efficient process flowsheet for product recovery and compliance with regulatory guidelines. This paper will discuss our recent developments in mineral processing and hydrometallurgical technologies to recover gold and titanium dioxide from a wide range of feed materials including ores, concentrates and tailings.

Sep 1, 2012

By S. K. Dutta

Enormous amount of iron ore fines is generated, due to partly soft and friable nature, during mining. Coal fines are also produced during their processing. These fines cannot be used directly in ironmaking reactors. Utilization of these fines for extracting metal is of vital concern for resource conservation and pollution control, and therefore, a novel concept of agglomeration by cold-bonding is developed. Composite briquettes/pellets of iron ore fines with coal fines were prepared in the laboratory by cold-bonding technique. Various binders such as lime, Ca(OH)2, slaked lime, dextrin, molasses, fly ash etc were employed either alone or in combination in different proportions for making composite briquettes/pellets. It was possible to obtain dry strength of composite briquettes more than 300 N/briquette in some cases and more than 200 N/briquette in many trials. The combination of fly ash with slaked lime and molasses produced the highest strength, more than 400 N/briquette. Drop strength and shatter index values of composite briquettes/pellets were also measured. In briquettes, best compressive strength (978 N/briquette) is observed by using polyvinyl alcohol (PVA) binder. In pellet, best compressive strength (362 N/pellet) is achieved by PVA; shatter index (0.1%) and dry drop strength (158 numbers) are also good. Compressive strength above 200 N/pellet is obtained by fly ash, slaked lime and molasses combination.

Sep 1, 2012

By P. M. Solozhenkin, V. P. Nebera, V. D. Skorohodov

"Aqueous dispersions of air specifically prepared on the basis of flotation reagent solution acquire active properties in relation to the solid surface and may be imply as a medium for flotation ores. Such aerated solutions were defined as Activated Aqueous Dispersions of Air (AADA) with 5-6:1 ratio and the procedure of mineral separation was defined as a flotation process under non-equilibrium conditions. These procedures differ from conventional flotation mainly in reagent interaction with minerals through their adsorption films on gas bubbles simultaneously forming flotation complexes. Gas-liquid mixture is kept till an adsorption layer of reagents close to the limit value is formed on the surface of bubbles. The theoretical basis of AADA is considered.The results of two-phase gas- liquid mixture (AADA) were studied. Two versions of AADA were considered. Electrical surface potential of the air bubbles with the surfactant film, untreated minerals particles in Coulomb attraction and flotation complex formation were analyzed. Special flotation machines were constructed for separation of mineral suspension in air dispersion, whose effectiveness was confirmed in flotation of apatite waste of Kovdor ore. FK-9 machine introduced on Kovdor iron ore combine for the recovery of apatite from current departures of factory. The froth product contained 7.2 % P2O5, with recovery of 44 % apatite, which was processed for getting melted phosphoric-magnesium fertilizers."

Jan 1, 2003