Search Documents

By Yang Zhao, Tao Xiu-xiang, Chen Song-jiang

"China is rich in low-rank coals that account for 45.68% of existing coal reserves in China. The clean and efficient utilization of low rank coals is of great significance for ensuring the effective energy supply and promoting economic development and environmental protection. In order to solve the difficult problem in flotation of low rank coal, it has become the focus of research in the related field that oily bubbles instead of air bubbles are taken as a carrier in flotation to improve the attachment efficiency and recovery of low rank coal. In this paper, low rank coal slime collected from Shendong mining area was used as the experimental material, and it focused on the characteristics of oily-bubble flotation process of low rank coal. Additionally, difference in conventional flotation and oily-bubble flotation was discussed. The induction time between air bubbles, oily-bubbles and fine low rank coal particles was measured. The results indicated that the induction time between oily-bubbles and coal particles was obviously lower than that of air bubbles. By comparing the foam height of air and oily bubbles, it was found that the amount of oily bubbles is less than air bubbles, causing relative low flotation rate of oily-bubble flotation at initial stage. Besides, the maximum foam height and half-life of air bubbles and oily-bubbles were measured respectively. The results showed that the stability of oily-bubbles was higher than that of air bubbles, which is benefit for the enrichment of concentrates. The clean coal water recovery of oily-bubble flotation is lower than that of air bubble flotation, which indicated oily-bubble flotation is lower in water entrainment. INTRODUCTION China is the largest energy consumer in the world, accounting for 23% of global energy consumption in 2016 and 27% of global energy consumption growth. Whereas coal is taken as the major primary energy source and its share of China’s primary energy consumption is 62% in 2016, in which the low rank coals, such as lignite, long-flame coal, weakly caking coal, and non-caking coal, accounted for about 50% of total coal production capacity (China’s energy market in 2016, BP). Moreover, the exploitation and utilization of low rank coals and other coals that are difficult to float have been an important strategy for China’s sustainable development of the coal industry (Liu et al., 2014). However, the combustion of low-quality coals leads to a serious environmental pollution. In addition, the deterioration in geological conditions of coal resources, and the increasing improvement in the mechanization for mining significantly caused the increased amount of fine coal."

Jan 1, 2018

By M. Q. Xu

During the flowsheet development for a potential commercial Cu/Ni separation plant at the In-co?s Sudbury operation, extensive laboratory and miniplant studies were carried out. There are two potential feed streams for Cu/Ni separation at the existing operation. It is shown that Cu/Ni separation from the rougher concentrate is relatively simple without need of regrind. However, Cu/Ni separation can be difficult from the bulk concentrate because of the presence of excess flotation reagents in the bulk concentrate slurry and locked particles. Excess flotation reagents created excess froth increasing entrainment. By replacing the slurry water with tap water and with addition of some hydrogen peroxide, entrainment is minimized and good Cu/Ni separation is achieved on the bulk concentrate. Fine regrind is required to increase liberation of the locked particles for ultimately high copper recovery at the minimal nickel content.

Jan 1, 2014

By Yonghui Hu, Hongxiang Ran, Honggang Wei

"A new PVM vertical ring high-gradient high-intensity permanent magnetic separator authorized by China Invention Patent ZL201110294866.4, which featured with vertical magnetic field structure was developed to dramatically save energy consumption and running costs compared with electromagnetic separators. The specific magnetic circuit design ensures PVM separator generating high magnetic field intensity as well as solving equipment large-scaling. The newly developed industrial PVM separator has been proved suitable for recovery of weak magnetic minerals or purification of non-metallic minerals benefiting from its high background and induction magnetic field intensity up to 0.8/1.5T, stable service performance and low running costs. The first ?1.5mm PVM separator has been applied in removing iron from quartz sand in Fengyang, Anhui, and ?2mm PVM separator will be installed to separate hematite. Industrial applications and tests proved that PVM separators could gain similar separation effects and especially save more than 80% of power consumption compared with the conventional electromagnetic high-gradient high-intensity magnetic separator, which will contribute a lot for energy conservation and environmental protection. The development of high gradient magnetic separator technology has played an important role in utilizing weak magnetic minerals, which has been widely used in many mining enterprises. The main forms of high-gradient magnetic separators include both of electromagnetic high-gradient and permanent magnetic high-gradient. The vertical ring high-gradient high-intensity permanent magnetic separator features with high magnetic field gradient, large processing capacity and never clogging, which has been widely used in recovering fine weak magnetic mineral and purification of non-metallic minerals[1-3]. However, electromagnetic coils excitation needs more energy consumption, and relatively high running costs and maintenance costs as a result of the complicated cooling system. So permanent magnetization of the electromagnetic magnetic separation equipment is a very important research direction at present. With the continuous improvement of resource utilization standard and efficiency requirements, high energy consumption of the electromagnetic vertical ring magnetic separator have been highlighted, which has affected the economic benefits of mining enterprises to a certain extent. In the aspect of high-gradient high-intensity permanent magnetic separation equipment, considerable researches have been carried out at home and abroad and many small-sized prototypes were developed yet never strode into large-scale industry applications[4-6]."

Jan 1, 2018

By S. J. Neethling

"This paper examines the impact of several key variables on the performance of flotation cells. The study makes use of a simulator for the froth phase of the flotation vessel, as the main purpose of this study is to separate the impact of different variables from one another. In experiments it is very difficult to separate the effect of variables from one another as a change in a singe input parameter, such as air rate, invariably also affects many of the other key variables, such as bubble size and bubble bursting rates.In order to achieve this a base case simulation that is typical of many of the rougher cells found in sulphide flotation circuits was carried out. Four key variables, air rate, incoming bubble size, surface bubble size and the fraction of the bubbles flowing out of the cell unburst, were varied in order to obtain the system.s response.The most significant results were obtained when the bubble size was varied. An increase in the incoming bubble size has the effect of reducing the pulp zone recovery, but increases the froth zone recovery. If it were possible to vary the incoming bubble size without influencing the overflowing bubble size, the impact of the change would be unclear because of these two competing effects. The effect of a change in the overflowing bubble size has an opposite effect on the froth recovery, with larger bubbles resulting in lower froth recoveries.A final interesting result is that all the effects examined affect the process to a similar degree, which implies that none of these variables can be disregarded, either in industry or in further research."

Jan 1, 2003

By Tamara F. Kondrateva, Evgenia E. Savari, Galina V. Sedelnikova, Rauf Y. Aslanukov, RAS (INMI), Grigori I. Karavaiko

"The investigation is dedicated to study of biohydrometallurgical processing of refractory gold-arsenic concentrate with the large content of pyrrhotite. Sulfide concentrate of chemical constituents: 75g/t Au, 4,7g/t Ag, 6,3% As, 29,3% S, 2,3% Sb, 0,5% ? (organic) and of mineral composition, %: 11,8 arsenopyrite, 39 pyrrhotite, 12 pyrite, 2,9 antimonite and the rest – aluminosilicates, carbonates and quartz, was studied. The recovery of gold from concentrate by cyanidation is 51,2%. The rest of gold is embedded as finegraded segregation in sulfides.Sulfide oxidation process study is described. Bacterial oxidation was executed on a pilot laboratory unit using combined autotrophic bacterium: A. thiooxidans , A. ferrooxidans, Leptospirillum ferrooxidans and sulfobacillus thermosulfidooxidation, pH=1,5-2,2, t=28-32?C, oxidation time 120 hours. Pyrrhotite is the least stable sulfide mineral with electrode potential 0,45V versus arsenopyrite (0,55 V) and pyrite (0,55-0,6 V) and is oxidated primarily. Pyrrhotite oxidation is followed by large amount of elemental sulphur, which has a bad influence on cyanidation.It’s established that the rate of arsenopyrite (for the first 48 hours) from concentrate containing 39% pyrrhotite is 2-3 times as less as the rate of arsenopyrite bio-oxidation from concentrate without pyrrhotite. The arsenopyrite bio-oxidation is accelerated only after the elemental sulfur was oxidized by bacterium A. thiooxidans and elemental sulfur percentage was reduced from 6,8 to 3,9%. The bacterium concentration is increased from 2,5x107 to 2,5x109 cells/ml. Almost full oxidation of arsenopyrite (98%) and pyrrhotite (98- 99%) is finished in 120 hours. We have studied two pretreatment methods for elimination sulfur content influence on cyanidation: aeration in lime and electrochemical treatment. Such an operation enables to have supplemental oxidation of elemental sulfur and other oxygen and cyanide absorbants before cyanidation. After treatment the content of elemental sulfur was decreased from 3,9 to 2,2%, gold recovery from 90 to 96% and cyanide consumption from 16,2 to 7,2 kg/t decreases. The content of toxical rhodonite-ions in liquid phase of pulp and disinfection reagents consumption were decreased as result of elemental sulfur content in bio-oxidated product reduction."

Jan 1, 2003

By Ana C. C. Pacheco, Maurício L. Torem

"The aim of this work was the study of the effect of the type (Fe3+, Al3+ and Fe3+ and Al3+ mixture) and of the coprecipitant concentration on As5+ removal by ACF. Removal of As5+ using sodium dodecyl sulfate (SDS) as a collector was studied by Adsorbing Colloid Flotation (ACF) at laboratory scale. The morphology of the precipitate retained in the foam was analyzed by Scanning Electron Microscopy (SEM/EDS).In order to investigate the effect of the initial concentration of Fe3+ on As removal, sets of experiments were performed with a concentration of Fe3+ in the proper range of pH (5,0 – 6,0) previously observed in the coprecipitation tests. As removal improves significantly as the concentration of the coprecipitant agent increases from 60 mg.L-1 (77,4%) to 80 mg.L-1 (99,7%). This is probably due to the higher concentration of ferric hydroxide (Fe(OH)3) which provides a larger surface area available for adsorption of As. From the initial coprecipitant concentration of 80 mg.L-1, As removal has shown to be rather high (? 99,7%), with the maximum being (99,9%) by using a Fe3+ concentration of 160 mg.L-1. Therefore, for a maximum As removal, under these test conditions, the optimum concentration of Fe3+ is 160mg.L-1.This paper also shows the effect of the initial concentration of Al3+ on As removal at a suitable range of pH (7,0 – 8,0). A very significant increase on As removal was found to occur as the initial concentration of coprecipitant was increased from 60 mg.L-1 (35,7%) to 80 mg.L-1 (97,7%) and a decrease in As floatability (43,7% - 54,5%) was found to occur from that Al3+ concentration amount. Based upon those results, the optimum Al3+ concentration so as to remove As under these test conditions is 80 mg.L-1."

Jan 1, 2003

By Fengnian Shi

In the current energy-sensitive world, sustainable development in the mineral industry will require new, better and more efficient processes. Novel comminution methods, which offer the prospect of achieving the required outcomes of size reduction and mineral liberation at lower energy consumption, are continually being sought. In the past five years, extensive research using high voltage pulse electrical comminution technology has been carried out at the Julius Kruttschnitt Mineral Research Centre (JKMRC), in collaboration with selFrag AG. The major outcome of this research is the development of the concept of pre-weakening ore particles by electrical comminution procedures to reduce the energy consumption in the downstream grinding circuit. The research has also verified the preferential liberation of valuable minerals by electrical comminution. Given the advantages, several potential applications of electrical comminution in the mineral industry are proposed, including AG/SAG mill feed pre-weakening, pebble treatment, ball mill feed pre-weakening, early recovery of the liberated valuable minerals, crack/micro crack generation for improved leaching, and smelter slag treatment. For the mineral industry to utilize electrical comminution, two emerging issues identified from the research need to be address. They are the energy consumption by electrical comminution in the locked cycle treatment and the facilities scale up necessary to move this technology from the laboratory to the plant. Keywords: high voltage pulses, electrical comminution, energy efficiency, mineral liberation

Sep 1, 2012

By Gus Van Weert, Samuel A. Bolorunduro, David B. Dreisingerm

"As deposits of high-grade base metal sulphides become depleted, attention must be focused on the treatment of complex sulphides, which contain significant fractions of precious metals such as gold and silver. Acid pressure oxidation is a promising process for these materials and the recovery of silver and gold will improve the economy of the process. Gold can be recovered from the oxidised residues, however, silver is incorporated into the jarosite specie and the cyanidation of the resulting residue yields very low recovery.Pressure oxidation of various complex sulphides was carried out at 110-150°C in sulphate media with additions of potassium iodide under conditions similar to industrial autoclaving. The resulting residues were subjected to cyanidation. High recovery of silver, up to 98%, was achieved because its incorporation into lead-hydronium jarosite during the pressure oxidation was minimised, while its deportment into the cyanide-soluble silver iodide was favoured. Silver recovery decreased slightly at high temperatures (140° and 150°C) because of the enhanced stability and kinetics of lead-hydronium jarosite, but this could be overcome by increasing acidity and iodide concentration of the autoclave slurry."

Jan 1, 2003

By Shenxu Bao, Ying Bian, Xiang Liu, Liuyi Ren, Yimin Zhang, Chun Liu

Efficient enrichment of high-carbon low-grade mica stone coal containing vanadium is a key problem in the mineral processing field, and the mature beneficiation process is yet to be developed and applied. In this paper, a special mineral mica type of stone coal containing vanadium from Tongshan, Hubei Province, China was selected as the research object. Chemical analysis results show that this mineral contains V2O5 0.71%, SiO2 49.28%, C 13.44%, and CaO 6.26%. Scanning electron microscope (SEM) shows that vanadium generally exists in all kinds of mica minerals in 20 µm to 50 µm fractions. Mica stone coal containing vanadium must be ground to a particular fineness (approximately 45 µm). To reduce acid consumption during vanadium extraction from stone coal through acid leaching, a pretreatment process was proposed to enrich micas by using shaking table and flotation methods. A new combined technology process was implemented, resulting in a 0.96% improvement in the vanadium grade of raw materials in the succeeding process. Vanadium losses were controlled to 4.57% through the pre-concentration process, which reduced the burden of the subsequent procedure. The content of high acid consuming minerals was also diminished, such that approximately 6612 CNY was saved from producing 1 t V2O5. Therefore, stone coal containing vanadium should be pre-concentrated by using an appropriate combined process to reduce costs.

Jan 1, 2014

Coal preparation plants usually operate with water in a closed circuit mode. In this practice, large quantities of water is continuously being recycled. To compensate the natural losses, only small quantity of fresh make up water is added into the circuit. As a result, a gradual build up of residual concentrations of flotation reagents (frothers, collectors, coagulates etc.) take place in the water and the concentration levels of the contaminants increase. Besides, the recycled water accumulates higher amounts of total dissolved components (1600 ppm) and hardness (740 ppm) than the fresh water. Nearly 80 ? 85% of the process water used in a coal preparation plant is utilized in treating the coal fines in flotation circuit. The presence of certain alkali earth metal ions (e.g., Ca++, Mg++) may adversely affect the flotation performance as they precipitate sparingly soluble hydroxyl complexes on the coal surface and change its surface charge. These studies showed that the use of recycled water in flotation has a significant effect on the selectivity and kinetics of the flotation process because, the dissolved compounds, both inorganic and organic, alter the chemistry radically. By treating the recycled water through a softening process, the concentrations of alkali earth metals and hardness were reduced significantly. The concentration of alkali earth metals and hardness were reduced to 10 ppm and 35 ppm respectively in the softened recycle water. From the selectivity studies, it has been observed that the flotation yield and recoveries increased by four to seven units by softening the recycled water. The kinetic studies indicated that the clean coal particles followed first-order kinetics. The kinetic parameters namely, flotation rate constant (k) and maximum recoveries (R8) of flotation, were found higher with softened recycle water than the recycled water. This reduces the residence time in the flotation cell and thereby, increases its productivity. Keywords: coal flotation, hardness of water, water chemistry, softening process, selectivity, kinetics, flotation rate constant and maximum recovery

Sep 1, 2012

By Markus A. Reuter, Yongxiang Yang, James R. Post

The packed coke bed in the lower part of an iron making blast furnace, the dead man, dissolves slowly in a pool of hot metal, which is tapped regularly. The coke particles of the dead man not only exhibit a size distribution, but also their size distribution is non-uniform throughout the dead man and as a result, the porosity of the dead man is non-uniform. This causes the flow of hot metal through the dead man to be irregular and non-uniform, bringing about channelling in the coke bed. Channelling is detrimental to the refractory lining life of the hearth of a blast furnace. Using population balance modelling and a porosity model it is possible to keep track of the local changes in size distribution and bed porosity during dissolution of coke particles. Numerical simulations show that carbon dissolution from a packed coke bed (with particles which exhibit a size distribution) increases the average porosity, decreases the mean particle size and changes the size distribution to a distribution with a smaller size range. Influence of the type of initial size distribution (mean, variance) is investigated. The calculated changes in porosity are used to dynamically adapt the flow and the mass transfer (kinetics) during calculations. This approach provides the possibility to implement dynamic porosity calculations for CFD applications, and thus simulate the results of various coke types and particle size distributions on dissolution and flow behaviour.

Jan 1, 2003

By Z. M. Wang

A large scale a polymetallic mine in north China is a refractory ore containing many useful com-ponents: W, Mo, Cu and Fe. Mineralogical investigation shows that the deposit is a quite complex one due to fine disseminated size and unevenly distribution of valuable, intergroth of sulphide and tungsten minerals, concurrence of scheelite and calcium minerals. Based on ore characteristic, a flowsheet is used by the floatation processing of sulfide minerals superior to scheelite. Bulk sulphide flotation is used in sulphides. Mo and Cu are floated in sequence after sulphides regrinded. Tungsten mineral is floated using combined depressant that is an effective depressant to gangue, and can improve the grade of rough tungsten concentrate. Compound depressant has high effective in removal of collector in gangue and sulphide, and tungsten is activated also. High quality of tungsten concentrate is obtained at satisfactory recovery. The test production obtains Mo concentrate with grade of 48.16%, recovery of 81.43%; W concentrate with grade of 66.47%, recovery of 78.19%; Cu concentrate with grade of 23.14%, recovery of 56.6%; Fe concentrate with grade of 67.33%. The valuable metals are recovered comprehensively and well techno-economic index is obtained. The mine enterprise profit is increased greatly.

Jan 1, 2014

By T. S. Qiu

In view of the bad effect that Na-bentonite direct adsorb Pb2+-containing wastewater, this article has carried out two kinds modification treatment on Na-bentonite: the direct microwave radiation modification and microwave radiation organic modification by adding quaternary ammonium salt?cetyltrimethylammonium bromide,and analysis the main influencing factors of the modification effect. In static conditions, preparing Pb2+-containing wastewater as the research object, it has respectively studied the effects of Na-bentonite, microwave soil of direct microwave modification and microwave soil of organic modification on the process of adsorption Pb2+, and discusses the effects of pH value, temperature, adsorbent dosage, stirring time on the adsorption Pb2+ in wastewater by modified bentonite, at the same time it does a verification test to the practical Pb2+-containing wastewater. Comparison the effects of adsorption Pb2+ in wastewater, the results show that organic modified microwave bentonite is obviously better than direct microwave modified bentonite and Na-bentonite, and can make 6 mg/L Pb2+-containing wastewater meet the national discharge standards. Through scanning electron microscope, the result of test is that organic modified microwave bentonite is the cause of improving adsorption Pb2+ in wastewater. Preparing modified bentonite by microwave heating will not only shorten the response time, reduce energy consumption and work-load, but also modified effect is good.

Jan 1, 2014

By P. V. Malyarov

"This paper examines the grinding and wear processes in drum mills. A summary of the industry’s long-term experience with the proposed linings is presented. A method is proposed for assessing the efficiency of the grinding energy distribution between the successive stages. A case study is presented of grinding energy redistribution at Talnakh Concentrator by replacing spiral classifiers with a drum-type hydraulic screen. The problems of the kinetics of grinding processes in ball mills and semi-autogenous (SAG) mills are examined. It is demonstrated that in ball mills the feed particles are disintegrated by triaxial compression in the mill zones where discrete slippage of the charge occurs at major force interactions between the layers. Mechanism underlying increases in the specific energy consumption in grinding circuits based on SAG mills is shown.The problem of improving the throughput and reducing the specific energy consumption in mineral feed grinding is highly relevant because of the significant energy intensity. Up to 80% of the consumed energy is used to disintegrate ore fed into the drum mill. At all development stages of the drum mill grinding theory, the researchers have paid a great deal of attention to studying the patterns of the charge motion and the kinetics of the feed particles disintegration processes. In [1], it was shown that, due to the slippage between the charge layers being lifted, drum mills at concentrator plants operate in a mixed cascade and waterfall mode. A feature of the mixed mode is the toe zone, where the charge contacts the lining and the transition to a circular path takes place. Studies of the charge motion in the toe zone made it possible to develop a method for designing cross-sectional profiles of lining plates [2] for ball mill drums. The method is based on the principle of interaction between the balls and the lining, where the non-working rear surfaces follow the relative motion path of the balls before impacting the lining, while the working surfaces are orthogonal to the rear ones. Lining with the proposed profile provides contact with the charge and slippage-free transition to a circular path. This ensures an longer service life of the lining, a reduction in specific energy consumption, and an increase in the mill’s feed rate. The proposed method is applicable when designing lining plates of various materials. Steel liners with the proposed profile have been successfully operated [3] for more than 40 years at a number of projects in the industry."

Jan 1, 2018

By Z. F. Dai

The Thompson Nickel Belt, located in Northern Manitoba, Canada, contains more than 400 million tonnes of ultramafic low-grade nickel mineralization in 9 deposits. One of these, the Pipe deposit, was mined between 1971 and 1983 producing a Ni concentrate of 9% to 11% grade at 73% recovery. The operation was terminated because the poor recovery, low Ni grade and high MgO con-tent of the concentrate made processing this ore uneconomical at the metal prices prevailing at that time. Vale Inco is now re-evaluating these deposits with the intent of providing a new source of concentrate for its Thompson integrated processing facility. It is known that serpentine slimes coating on the sulphide surfaces are responsible for the poor metallurgy. Various desliming methods were tested including settling, elutriating, tabling and hydrocycloning. Hydrocycloning has proven to be the most effective means of desliming. With a feed assaying 0.70% Ni and 33% MgO, a rougher flotation concentrate assaying 22.7% Ni and 4.8% MgO was produced at a Ni recovery of 62.5% (relative to the feed to grinding), with no utilization of slimes dispersants. Another 16.6% Ni recovery was achieved in scavenger flotation resulting in a total Ni recovery of 79.1%. Batch flotation tests using various flowsheet configurations to optimize the grinding, desliming, reagentizing and flotation conditions are in progress.

Jan 1, 2014

By Kaustubh Joshi, Pradip, Beena Rai, Venugopal Tammishetti

"Rapid depletion of high grade iron ores coupled with the increasing demand for the blast furnace grade iron ore in recent times has shifted the research focus on the development of appropriate technologies for the utilization of low - grade alumina rich iron ore slimes. These slimes are currently being dumped into tailing ponds owing to their high alumina content. Typical constituent minerals present in the Indian iron ore slimes are hematite, goethite, gibbsite and kaolinite. Considering the fine particle size distribution (<37 microns) in the slimes, selective dispersion-flocculation seems to be one of the most appropriate process which has been explored by us. We present our successful results on a natural iron ore slime sample obtained from one of the mines in India. We have been able to achieve a concentrate assaying >67% Fe, and <3% Al2O3 and 2.8% loss on ignition (LOI) from the slime sample assaying 60.4% Fe, 7.7% Al2O3 and 5.45% LOI with an Fe recovery of 62-69% simply by adjusting the pulp pH. We have scaled up the process to a semi batch scale as a prelude to commercialize it for the beneficiation of low grade iron ore slimes."

Jan 1, 2014

By Xie Jiyuan, Hu Yuehua, Yang Songrong, Zhu Zhansheng, Qiu Guanzhou

"By the end of 2000, the first bio-oxidation plant in China that designed by ENFI come successfully into commercial operation in Yantai Gold Smeltery. Its capacity is 50t/d of refractory gold ore concentrate. After the extension, the capacity of bio-oxidation plant reached 80t/d of refractory gold ore concentrate at end of 2001.The refractory gold ore concentrate treated is from different gold mines. After proportionate feeding, the feed typically consists of Au (52.7g/t), S (24.42%), As (3.58%).The bacterial culture used in the bio-oxidation circuit is taken from a mine in south of China, and has been grown over 20 years on a variety of sulfide concentrates in a laboratory of mineral processing, and has shown to be adaptive to growth in a high concentrations of arsenic. It is a mixture of mesophilic microorganisms. The nutrients used in the bio-oxidation process are (NH4)2SO4, KH2PO4, KOH.Before feeding to bio-oxidation circuit, the concentrate would be milled to minus 43µm. The biooxidation product is fed to solid/liquid separation system that consists of a thickener and two press filters, solid from the system is fed to CCD circuit, liquid from the system is fed to neutralization area. The neutralized product is fed to another solid/liquid separation system, and the solid from the system is disposed of on a wasted quarry pit, the liquid from the system is returned to bio-oxidation circuit for reusing."

Jan 1, 2003

By Yagmur Sirinyurt, Ayhan Ali Sirkeci, Gülay Bulut, Mustafa Özer, Tuncer Acar

"The basic requirement of glass industry for the silica sand is at least 99% SiO2 content. On the other hand, coloring impurities such as Fe and Ti, must be removed. Flotation is the most widely used method for the purification of silica sands from impurities. In this study experimental studies were carried out to reduce Fe content of Mersin (Turkey) district silica sands by flotation. Silica sand sample with a d80 particle size of 1.85 mm was reduced below 0.5 mm in size. Then the size fraction -0.5 +0.106 mm was subjected to flotation tests. In flotation tests, sulfonate-type R801-R825, fatty acid based DER NA 7 (Produced by a Turkish company) and HA110-HA150 a blend of various chemicals produced by Mersin Cam-Is Mining Company (producer of glass raw materials) were used as collectors. Flotation tests showed that sulfonate type R801-R825 collectors provided much better results in acidic medium (pH: 3). The optimum pH value for DER NA, HA150 and HA110 collectors was found to be 7. It was observed that the addition of collector at once caused an increase in the amount of floated product that resulted in a loss of silica to the tailings. In the case of multistage addition of the collector much better selectivity was achieved. As a result of flotation tests conducted under best conditions, a concentrate assaying 0.046% Fe was obtained with a weight percentage of 93.4 when DER NA 7 was used as a collector. In the case of R801-R825 a concentrate was produced with 0.058% Fe content with a yield of 98.4%. On the use of HA150-HA110 the concentrate was produced with 96% weight recovery and 0.052% Fe content."

Jan 1, 2014

By Hermann Wotruba, Lars Weitkämper

"Dry coal dressing was popular during the 1950’s and 60’s in many parts of the world. The devices mainly used were air jigs and air tables.The increase in ash and moisture content of run-of-mine coals due to the wide advanced mechanisation of mining methods during and after this period led to that pneumatic devices being unable to treat run-of mine coals with the desired efficiency. Since the 1960’s almost all new coal preparation plants have been based on wet processes that are highly efficient in terms of coal recovery and their ability to handle damp and sticky run-of-mine coals. (Frankland, 1995)However, water is becoming increasingly costly and the disposal of fine products, containing most of the water, is an environmental concern. There would be significant cost savings and a lower total energy consumption if coal could be cleaned dry. Efficient dry coal treatment would be an interesting solution in desert, arid or cold areas.In Germany one dry coal dressing plant is in operation. This is the last operating dry coal dressing plant existing in Europe. The actual technical standard of dry coal dressing has been analysed during test-work and sampling in this plant (Saar Region in Germany). The process and the advantages and disadvantages are presented. The plants problems are low efficiency in the fine fraction –6 mm and the coarse fraction +30 mm and a low overall throughput as well as the lack of an automatic process control system. The separation results in the medium size fractions between +6 and -30 mm are excellent"

Jan 1, 2003

By M. Brozek, W. Pawlos

"The separation of raw materials in the separator with ferromagnetic liquid occurs due to differences in magnetic and gravitational properties of respective components in relation to each other and to the liquid. In the separator with wedge-shaped pole shoes and the working space axis inclined at a certain angle to the horizontal direction, the paths of grain movement at fixed separation conditions depend on its physical properties. Due to this, the levels of grains outlet from the separator working space are differentiated according to differences in their physical properties. The distance between the levels of outlets from the separator working chamber depends on magnetization of the liquid which is proportional to the liquid density, on the magnetic field intensity and the inclination angle of the separator working passage to the horizontal axis. The separation accuracy is higher the larger is the distance between the outlet levels.The paper will present the methods of visual observation and recording of movement paths of coal grains of different physical properties in the paramagnetic liquid which was the water solution of manganese chloride. The paths were recorded with a video camera in the working chamber by means of a specially constructed device, acting as a periscope, which were then transformed into digital images. Experimental movement paths were confronted to the paths obtained in a theoretical way by means of solving differential equations of movement by a numerical method, achieving good compatibility of experimental and theoretical results. The equations of movement were solved with taking into consideration the drag force, expressed by formula for laminar and dynamic conditions of motion.The course of the path of grain movement depends on grain and liquid physical properties, magnetic field intensity and inclination angle of the working space to the horizontal direction. The two latter parameters can continuously control the process of separation."

Jan 1, 2003