Search Documents

By Yuhe Tang

High Gradient Magnetic Separator with Horizontal Magnetic Line is a new type High Gradient Magnetic Separator product. It has many specific advantages, such as water-air joint discharging technique, double pulses pulp dispersion technique, multi-magnetic gradient for collecting matrix with different diameter rods, better discharging rate with the especial matrix dispose, high separating accuracy and wide applicability. In this paper, the author makes a description of High Gradient Magnetic Separator with Horizontal Magnetic Line, and puts its emphasis on analyzing industrial production data using high gradient magnetic separator with Horizontal Magnetic Line to separate weakly magnetic minerals. It is found that as the rougher for weakly magnetic minerals separation, High Gradient Magnetic Separator with Horizontal Magnetic Line has more stable metallurgical performance and cheaper running costs than other types of High Gradient Magnetic Separator when the properties of the ore change greatly and there is in the case of embedded fine particle size distribution. Keywords: high gradient magnetic separator, self cleaning technology, horizontal magnetic line, water air discharging technique

Sep 1, 2012

By J. Qiu

By means of natural sedimentation, two different bentonite samples from Shandong province were purified, this paper studies the Hydro-properties of the two purified montmorillonite samples. Firstly, the layer charge of two purified montmorillonite samples were calculated by crystal structure formula reckon method and general hydro-properties were also measured. The research results showed that the layer charge of montmorillonite correlated well with its hydro-properties: mont-morillonite with lower layer charge had better hydro-properties, such as Mont-1, which had higher swelling volume and gelling value with lower CEC; while, montmorillonite with higher layer charge had worse hydro-properties, such as Mont-2, which had lower swell volume and gelling value with higher CEC; it proves that the hydro-properties of montmorillonite depends on its layer charge characteristics, layer charge characteristic is the inherent factors deciding the hydro-properties of montmorillonite, montmorillonite with lower layer charge has better hydro-properties than the one with higher layer charge. In this paper, the relation between the medium condition and colloid performance of Mont-1 are also studied. The results show that the hydro-properties of Mont-1 could be changed by changing slurry concentration (w/w) and shear rate or adding certain amounts of inorganic cation electrolytes, dispersants and surfactants. The viscosity of montmorillonite slurry could be enhanced by increasing slurry concentration,adding univalentcation electrolytes (less than 4% w/w) or proper amounts of dispersants and surfactants (less than critical micelle concentration); The slurry viscosity could be reduced by decreasing slurry concentration, increasing shear rate, adding proper bivalent (more than 4% w/w) cation electrolytes or proper quantities of dispersants and surfactants (more than critical micelle concentration).

Jan 1, 2014

By V. Panayotov, M. Panayotova

"Wastewater from ores processing is often polluted by molybdate and sulfate (SO42-) ions. Sorption is one of suitable methods for removing those pollutants when presenting in low concentrations. This work reports results on adsorption of sulfate and molybdate ions on metal modified (with barium - Ba and lead - Pb) and organic reagent modified (with Hexadecyl-trimethyl-ammonium bromide - HDTMA) clinoptilolite. Zeolite’s modification with Pb, Ba and HDTMA increases its uptake capacity with respect to Mo(VI) at pH 3, with the uptake capacity decreasing in the order CL-Pb > CL-HDTMA > CL-Ba. Lead-modified clinoptilolite shows high uptake with respect to Mo(VI) in acidic, neutral and slightly alkaline conditions. The presence of SO42- in concentrations twice higher than the amount of Mo(VI) do not interfere with the Mo(VI) removal by CL-Pb. Zeolite’s modification with Ba and Pb renders it able to immobilize SO42- from water in the pH range 3-9. Kinetics of the uptake process is best described by the pseudo-first order kinetic equation. Increasing the initial concentrations of Mo(VI) and SO42- increases the removed amount of pollutants. INTRODUCTION Wastewater from copper-molybdenum ores processing is often polluted by molybdate and sulfate ions. Molybdenum (Mo) migrates easily in water and consequently the Mo polluted areas could extend for hundreds and thousands of meters (Ryzhenko, 2010). Molybdate anion is the only Mo(VI) species in natural water, i.e. at pH > 6.0. Its median freshwater hazardous concentration affecting 5% of the species (HC 5.50%) is 38.2 mg Mo/L (De-Schamphelaere et al., 2010). The marine water chronic toxicity (HC 5.50%) is assessed at 5.74 mg Mo/L (Heijerick et al., 2012). The predicted no-effect concentrations (PNEC) are 12.7 mg Mo/L and 1.92 mg Mo/L correspondingly for freshwater and marine water (Heijerick et al., 2012a). When sulfates present in drinking water in excess of 250 mg/L they cause a cathartic action (especially in children) in the presence of sodium and magnesium, and when the concentration exceeds 600 mg/L, diarrhea. When sulfate-rich effluents are discharged into the environment, they may increase the acidity of water bodies and soils (Guimarães and Leão, 2014). Because of the adverse effects to human health and the environment, limits are set for SO42- concentrations in waters and wastewaters in the range of 250 / 500 mg/L."

Jan 1, 2018

By Andrew Logan

Newcrest has a strong history of growth over the past 20 years, yielding value from previously marginal ore bodies. We have grown regionally in Asia Pacific through our operations in Australia, Indonesia and Papua New Guinea, and also established a beachhead in West Africa. The company has a reputation of realizing value from large, low-grade deposits adopting step change approaches. Newcrest is focused on an overall strategy of gold, low cost, long life and moderate growth. Capability step changes play a large delivery role. They transition from a business offline-to-online approach as opportunities mature. Newcrest believes in a) Knowing what ?good? looks like, b) An open innovation approach to actively working with others, c) The leap frogging leverage of making the ?old new again?, d)An adopt-adapt-develop methodology enabled by rapid prototyping/piloting, e) Getting our handsdirty with test work and plant analysis, and f) Staying focused on a few high business leverage areas. This paper describes Newcrest?s approach and our experiences in establishing renewed metallurgical processes, specifically aimed at increasing innovation adoption. Some of our step changes discussed include: 1) Early waste rejection to avoid high energy processing downstream, 2) Broader gold product channels to reduce site based processing needs, 3) Lower energy processing, and 4) Geo-Metallurgy approaches. Keywords: Newcrest, gold, step change, open innovation, adopt, adapt, develop, offline, online, prototyping, old new again, waste rejection, low energy, geo-metallurgy

Sep 1, 2012

By V. A. Zhilina, I. V. Shadrunova, O. E. Gorlova

"The aim of the study is to develop and scientifically justify a new adaptive approach to the separating processes of deep and complex processing technogenic mineral raw materials. Technogenic mineral resources as a waste of mining and processing industry are mostly complex objects that have specific features of material composition and technological properties and make it processing ineffective with traditional schemes of mineral raw materials enrichment. Mineral wastes are regarded in this study as a complex object with a large number of signs in conditions of uncertain environment and object. However, adaptation is regarded as the process management system’ adaptation to the specific the properties of the object and the environment that has several hierarchical levels corresponding to different stages in the management of complex object. An adaptive approach is considered as a methodological basis of multivariate schemes for opening the mineral resources and creating mechanisms that could transfer these potential technogenic resources to the actual that significantly expand the mineral resource base of the country's black, coloured, rare, noble metals and construction materials. In this case, potentially the solution to the most pressing social and environmental problems associated with the adverse effects of past economic activity simultaneously with the commercial objectives. This approach to the wastes mining and related processing manufacturers meets the core idea of sustainable development as the balance of interests of State, society, business, private enterprise and each person in the areas of rational use of resources, economic efficiency and environmental safety. On the example of metal-containing raw materials in the form of slags of ferrous and nonferrous metallurgy, ferrous metallurgy sludge, mature fine tailings, the application of adaptive approach illustrates to the development of technologies of its deep and complex processing as phased, thoughtful movement from a comprehensive study of technogenic raw materials to build optimal topologies of technological schemes for processing the mineral wastes. INTRODUCTION Involving the Russian economy in the system of global economic relations significantly changes the nature of the country's competitiveness in the development of the world market and urgently requires competent management of its own natural and mineral resources. The latter at the present time in real economic processes cease to be a passive material foundation and become the producing basis in the production processes in the status of so-called natural capital. Introduced in the field of economic theory at the end of the 20th century, this term means both the flow of natural services and real natural resources. Consequently, natural objects, which act as natural resources of a certain production, today must necessarily be evaluated in a strategic sense. Modern standards of sustainable development presuppose that the economy should equally be oriented to balance the interests of the state, society, business, individual enterprise and each person in the spheres of rational use of resources, preservation of healthy ecosystems, ensuring well-being, high quality of life and environmental safety of not only the current generation, but also respect for the rights of future generations, that is, intergenerational equality. Most types of minerals are classified as non-renewable resources, therefore resource-saving in the sphere of mineral and raw materials complexes is one of the most important factors-indicators characterizing the degree of approximation to the model of rational subsoil use, and, consequently, sustainable development (State Report, 2017)."

Jan 1, 2018

By T. Kumaresan

The Bayer process used for refining bauxite to smelting grade Alumina serves as the linchpin of the Aluminum production industry worldwide. Even though the process is well established, the presence of impurities in the liquor affects the quality of product and imposes a major economic cost on the industry. This review article focuses on the issues pertaining to Gibbsitic (Al2O3.3H2O) precipitation circuit. The comprehensive review provides a basic understanding of the aluminum trihydrate precipitation and agglomeration phenomena. Crystal growth rate and agglomeration play a significant role in determining the output PSD of agglomerates. Hence, the effect of certain thermodynamic and hydrodynamic parameters along with the impact of impurities (oxalates, aldols, acids etc.) and additives on hydrate growth has been reviewed.

Sep 1, 2012

By Graeme Heyes, Warren J. Bruckard, Michael A. Somerville

"A limited series of laboratory batch flotation tests was conducted on a suite of calcium-ferrite-based slags made in laboratory smelting trials. The smelting tests were conducted as part of a wider CSIRO Minerals’ research project aimed at developing a single-stage continuous copper-making process. The objective of the flotation work was to maximise copper recovery and iron rejection from slags made in the process.The slags treated included a reduced low copper slag, an oxidised high copper slag composite, and a very reduced low copper self-pulverising slag. The copper content of the slags varied from 2.9% to 14% Cu. The copper was present as metallic copper, oxide copper and copper-calcium ferrite phases with the phase mix related to smelting conditions. The slags were crushed, ground, wet-screened at 355 or 210 µm to remove coarse metallic particles of copper, and floated at natural pH (about pH 11) using reagents and conditions appropriate for the selective recovery of the copper phases.In rougher/scavenger tests on the reduced low copper and self-pulverising slags copper recoveries above 92% were obtained with copper enrichment ratios varying between 2.3 and 2.9. For the oxidised high copper slag copper recoveries were poorer - only 47% of the copper was recovered with an enrichment ratio of 3.3. The presence of the slow floating copper-ferrite phases in the slags limited further (selective) copper recovery. Ageing of the high copper slag, that is, a significant delay between grinding and flotation, resulted in a deterioration of the copper flotation response.The critical parameter affecting the flotation of copper from direct converting slags was found to be the form of the copper in the slag. Slags containing a higher proportion of the more desirable form of copper for flotation will provide the best opportunity for high copper recoveries to be consistently obtained, allowing improvements in the economics of the overall copper-making process."

Jan 1, 2003

By S. Castro, L. Gutierrez

"Mining operations are often located in remote arid environments with limited access to fresh water. Shortage of fresh water in such cases makes it necessary to use seawater in mineral processing plants. Such plants treating Cu- Mo sulfide ores in seawater have been fully operational in Chile (e.g. Las Luces, Centinela). In many cases process waters used in commercial flotation plants (e.g. Mt Keith in Western Australia) are even more concentrated electrolyte solutions than seawater. This paper is an attempt at classification of the flotation operations carried out in process waters that are concentrated electrolyte solutions.INTRODUCTIONAccording to Gleick (1966), of the total Earth’ water resources 97.5% is in the oceans and ice caps, and thus only about 2.5% is fresh water. Shortage of fresh water in many parts of the world makes it necessary to use seawater in mineral processing operations. The existing commercial operations using seawater as well as recent research projects that deal not only with sulfide ores but also with apatite ores provide a lot of information that can now be generalized. The progress that has been made in this area is reviewed and based on this information an attempt is being made at classifying the flotation operations carried out in highly concentrated electrolyte process waters.SALT FLOTATIONFlotation in highly concentrated electrolyte solutions was studied by Klassen (Klassen, 1963). He reported that hydrophobic, bituminous coals, could float in salt solutions without addition of any other flotation agents. The process is referred to as salt flotation. Other inherently hyhrophobic minerals (e.g. talc, graphite, sulfur, etc.) were shown to behave similarly (Klassen and Mokrousov, 1963)As Figure 1 shows, some coals float quite well in solutions of Na2SO4, NaCl and NaNO3 (Klassen, 1963). While there are differences between the tested salts (explained by different foamabilities of these solutions) all the tests indicate that only bituminous coals float well in concentrated electrolyte solutions. 0.3 M solutions are quite sufficient to initiate a good and very fast flotation. If wettability of various coals is compared it becomes obvious that these well floating coals are very hydrophobic bituminous coals (Figure 2)."

Jan 1, 2018

By F. C. Yi

Discontinuous and consecutive process was applied to probe into the Kinetics and adsorption theory for Cs+ adsorbed by Zeolites under the conditions of temperature, time and fixed-bed dynamic adsorption. It indicated that the sorption kinetics behavior of zeolite?s sorption on Cs+ is ac-cord with pseudo-secondary velocity equation, velocity constant k2=0.0005213 g?mg min-1, and equilibrium adsorptive capacity is 147.0588 mg?g-1; The equation can be expressed as: Y=0.0068X+0.0887; From the analyzing of diffusion coefficients on different temperatures and times, the coefficient of diffusion is not only related with the fabric of mineral and the character of ions but also the temperature and time; When the ambient temperature hoisted, the diffusion velocity augmented rapidly; Cs+ would get over a certain energy barrier when it enters into structure of zeo-lite; This energy is expressed by activation energy, and its value is E=131.668818 kJ?mol-1; There are two dominating adsorption mechanisms in the system of zeolite absorb Cs+: ionic interchange and surface coordinate adsorption.

Jan 1, 2014

By S. S. Yu

In this paper, the producing process of using V2O3 as raw material to obtain vanadium nitride was analyzed through the means of thermodynamic. The analysis shows that conversion follows the principle of reduction step by step in the conversion process of V2O3. The temperature of the reaction system has prominent influence on the nitrogen content of products, and the reaction is very sensitive to temperature. As raising temperature, the fine grain structure of the nitrides is more evident, and the grain size of nitrides increases. At 1703K, the nitrogen content of the products tended to be constant after soaking over 3 hours.

Jan 1, 2014

By J. Y. ` Xie

The paper introduced bio-oxidation plants of refractory gold concentrate in China and CCGRI cultures. CCGRI cultures are composed of bacteria and archaea. Archaea Ferroplasma acidiphilum is very thick and fills whole mineral surface. It plays a more dominant role in CCGRI process. Several years of practice has proved that the operating temperature in bioreactors between 38~52?,gold recovery is almost same. Pulp concentration has been increased each year and reached to 25%.

Jan 1, 2014

By A. A. Rogozhin, E. G. Likhnikevich, S. I. Anufrieva, A. V. Kurkov

"Russia is among the nations holding the world's largest lithium ore reserves. Lithium is of key importance for the global economy. Therefore, it is important to review the current state of technology research aimed at finding the most effective solutions for the recovery of lithium from promising reserves in Russia. In Russia, a number of process solutions for the flotation of spodumene into salable concentrate (5% Li2O) have been implemented at the earlier existing complex low-grade ore concentration project. By applying these solutions, a sample of high-grade spodumene ore (4.7% Li2O) of the Greenbushes deposit was processed into a spodumene concentrate (7.5% Li2O) at a high recovery (~93%) of lithium. In Australia and Canada, new processes have been developed for the recovery of high-grade spodumene concentrates from high-grade ores using dense medium separation and flotation. For the recovery of mica lithium concentrates from low-grade ore, a flotation process was developed in Russia using the cationic collector ANP-2 and Oxifos-B as an additional collector. Low-grade ore containing 0.14% of lithium oxide was processed into a 2.7% Li2O concentrate. New hydrometallurgical lithium concentrate and ore processes are developed to avoid high-temperature (>1000 °C) roasting. The Sileach process (Australia) includes leaching of lithium ore with sulfuric acid in the presence of a halogen-containing component at a temperature of 95-115 °C. In the Russian process, lithium is recovered into an alkaline solution from low-grade spodumene ore in a pressure alkaline leaching environment (250 °C, NaOH concentration > 300 g/l). The developed concentration and hydrometallurgical methods will allow to design on their basis efficient processes for recovering salable products for hi-tech industries from lithium ores.INTRODUCTION Lithium has many unique and important properties. It is the least dense hard metal. Its alloys have some of the highest strength-to-weight ratios. Lithium has the lowest melting point of all known solid elements and is used as a highly-effective heat transfer medium. The high demand for lithium is due primarily to its unique electrochemical potential and low thermal expansion coefficient. It is used in the production of glass and ceramics, in petrochemicals, metals, medical and other industries. Since the late 20th century, the electronics industry has been the largest consumer of lithium. In recent years, lithium has attracted much attention also as an important component of ultra-lightweight electronic devices. It is also the preferred metal for electric batteries used in mobile electronic devices, vehicles, household power generators, making it an important resource for the development of environmentally friendly technology. Leading automotive brands have ambitious plans for the production of electric cars — Tesla Motors, VW, Toyota, GM, BYD Auto. It is expected that the production of electric vehicles alone will triple the demand for lithium by 2025. A sharp increase in the production of lithium is expected. Lithium has all the prerequisites to become a strategic resource of the 21st century. (Deutsche Bank, 2016; Bradley et al, 2017)"

Jan 1, 2018

By J. D. Miller, C. L. Lin

In general, x-ray computed tomographic (CT) techniques are able to provide 3D images of the internal structure of opaque materials in a nondestructive manner. The unique cone beam geometry allows acquisition of all 2D projections with only one rotation of the sample thus providing for fast data acquisition and better x-ray utilization, as a complete 2-D detector array receives the cone-shaped flux of rays. Thus, an isotropic 3D volume can be reconstructed without the mechanical translation and the stacking of sequential slices as is the case for more conventional CT scanners. In this regard, a state-of-the-art, custom designed xray microtomography facility to provide very detailed 3D spatial analysis of multiphase particles has been installed and is in operation at the University of Utah. The reconstructed 3D tomographic volume allows for an adjustable spatial resolution from 5 to 20 microns for sample dimensions from 10 to 40 mm in diameter, respectively. Utilization of this custom designed cone-beam x-ray microtomography system is discussed. Applications described include: coal washability analysis for the design and operation of coal preparation plants, liberation analysis for evaluation of grinding practice and separation efficiency, mineral exposure analysis for prediction of the ultimate recovery from heap leaching operations, and analysis of the pore structure network of packed particle beds for simulation of flow through such porous structures as encountered in filtration and heap leaching.

Jan 1, 2003

By Ying Gu

Automated mineralogy methods and tools, such as the Mineral Liberation Analyzer (MLA) and the QEMSCAN, are now widely used for ore characterization, process design and optimization. Several case studies published recently demonstrate that large gains can be obtained through grinding and flotation optimization guided by automated mineralogy data. However, since automated mineralogy can only provide the information pointing to where the process gains can be made, it does not directly impact the production gain. Thus, a question is often asked: how to value the contribution of automated mineralogy to process improvement of a particular plant. This appears to be a difficult question. On close examination however, it is found that this is essentially a question of the value of information and it is reasonably well documented in various other industries. Hubbard (2010), in chapter 7 ?Measuring the Value of Information?, dealt with exactly this type of problem. The value of information is the reduced risk of an investment and opportunity loss. The methods Hubbard developed can be applied to estimate the value of automated mineralogy, as well as metallurgical test work, which also produces information that reduces the risk of investment. This paper first introduces Hubbard?s theory on the value of information and how to measure it. It then applies his methods to estimate the value of automated mineralogy, using Anglo Platinum?s fine grinding project as an example. In this case, the value of automated mineralogy includes the reduction in investment risk worth US$ 62.5million, in project rejection worth US$197 million and in opportunity loss worth US$320 million. In the end, a general model is developed to allow the simulation of the value of automated mineralogy in different mining operations constrained by different parameters.

Sep 1, 2012

By Pat Turner, Abrie Schutte, Tim Olson, Roman van Ommen

The key to good cyclone circuit design and operation in primary grinding circuits will be discussed. Cyclone circuit design issues include individual cyclone design features such as cone angle or materials of construction, as well as orientation and manifold configuration. Cyclone performance issues as well as maintenance considerations will be detailed in an effort to achieve consistent cyclone operation with minimal coarse solids in the overflow. The new gMAXTM. cyclones will be introduced and evaluated using operating circuit data in closed circuit grinding applications

Jan 1, 2003

By Vasile Murariu, William Pate, John Herbst, Dilek Alkac

"Multiphysics models are essentially first principles models capable of providing very accurate micro scale predictions. The computational requirements for Multiphysics Models are extensive, precluding their direct use for flowsheet simulations. Population balance models get their form from theory but the model parameters have to be provided from experiments. The prediction errors for the population balance models are typically significantly higher than those for the Multiphysics Models but the computational effort for Population Balance Models is typically much less than that for the Multiphysics models. The hybrid model described here takes advantage of the strengths of each of the two primary model types and minimizing the weaknesses of each. The Multiphysics Model is used to perform high accuracy "experiments" that are difficult or impossible to conduct in laboratories or plants. The results of these experiments are combined with standard laboratory or plant data to parameterize and further enhance the Population Balance portion of the hybrid model. The creation of a useful Hybrid Model is demonstrated for a MP1000 secondary crusher. The validation of the hybrid crusher model is also presented. Finally the use of the Hybrid Model is illustrated in a full comminution flowsheet simulator."

Jan 1, 2014

By L. Pan

As an air bubble approaches a mineral surface, a thin liquid film (TLF) is formed in between. The excess pressure (p) in the film determines the kinetics of drainage, which is of critical importance in flotation. We have developed a new method of monitoring the kinetics for both stable and unstable wetting films and analyzed the results using the Reynolds lubrication theory. It has been found that initially a TLF is thinned by the Laplace pressure (pcur) due to changes in bubble curvature and subsequently by the disjoining pressure (?) created by the surface forces present in a wetting film. In the present work, we have derived an analytical expression for determining ? from the temporal and spatial profiles of TLFs on mineral surfaces. The results show that ? > 0 in a film formed on a hydrophilic surface and ? < 0 in a film formed on a surface hydrophobized by collector. Thus, the role of collector in flotation is to create a hydrophobic force and hence a negative disjoining present in wetting films. It is also found that smaller bubbles can create higher Laplace pressure, which helps the TLF drain faster.

Sep 1, 2012

By Shailin Lalloo, Allan B. Nesbitt

A fluidised bed was exposed to high gravities by placing it in a centrifuge. The bed expansions were measured and compared with the bed expansions predicted by the Richardson-Zaki model (1954). The Richardson-Zaki model was found to predict effectively the fluidisation behaviour of defined particles in this increased gravity environment.

Jan 1, 2003

By Svetlana Krashenina, Nebojsa Petrovic, Oscar Lopez

"As easily mined gold deposits are becoming increasingly rare, gold producers are turning to the processing of ores with polymetallic and copper mineralization. These base metals can create metallurgical and waste handling/disposal challenges, which can render the project uneconomic. Base metals such as copper compete for the cyanide reagent used to extract gold, necessitating the need to increase cyanide volumes and consequently, cyanide consumption costs. Copper will also stabilize in tailings water as weak acid dissociable cyanide, a form that is both difficult and costly to destruct. SART (sulphidization-acidification-recycling-thickening) process technology can be applied to remove base metal interferences in gold projects. SART breaks the copper-cyanide complex and precipitates the copper as a saleable copper sulphide concentrate. With the copper removed, the cyanide can be regenerated as free cyanide for recycle to the gold recovery process. This improves cyanide utilization efficiency and mitigates copper presence in tailings. Additionally, copper recovery generates an incremental revenue source to further improve project economics. Engineering Dobersek GmbH together with BioteQ developed a SART and AVR testing program to recover cyanide and maximize operational efficiencies at a gold processing plant in Kazakhstan with high cyanide consumption in the leach circuit. Results from on-site testing demonstrated that up to 99.98% of copper can be removed and precipitated as copper sulphide and 60-90% of cyanide can be recovered from the AVR and recycled for leaching, reducing total overall cyanide use. This paper provides an overview of the testing methodology and results together with a discussion on the potential of SART to improve gold production operations to deliver both environmental and economic benefits."

Jan 1, 2014

By Paulo Braga, Carlos Junior, Silvia França

"Lithium is the lightest of the metals, with high reactivity and great electrochemical potential. It has a low thermal expansion coefficient and high caloric value, and it forms very light and resistant aluminium alloys. These properties make lithium an attractive element for use in battery manufacture and glass and ceramics production, in addition to its applications in the aeronautic industry. Today, two sources of raw material are economically viable for lithium production: pegmatite rocks and brine. The world production, in 2012, was approximately 150,000 tons of LCE (lithium carbonate equivalent), almost triple the production in 2000. The forecasted consumption for the current year, 2013, was approximately 162,000 tons of LCE, and for 2020, it could be as much as 280,000 tons of LCE, stimulated essentially by the growth of world production of electric (EV), hybrid (HEV) and hybrid plug-in vehicles (PHEV), the batteries of which are based on Li-ions. With the growth of world demand and increasing prices, lithium minerals such as spodumene, petalite and amblygonite, once considered uneconomical for the production of lithium carbonate, are regaining their economic value. New projects to produce lithium compounds based on mineral sources are being developed in many countries, aiming to produce battery-grade lithium carbonate (99.95% Li2CO3). Although Brazil has large lithium pegmatite reserves, the domestic production of lithium carbonate and hydroxide is very low, at approximately 600 tons of LCE, which represents 0.4% of the world production. The application of these products is mostly in the grease and ceramic industries. The national lithium market is under government protection due to its potential use for nuclear purposes. Thus, the industrialization activities and import and export of ores and lithium minerals, as well as organic and inorganic products, such as metallic lithium and lithium alloys, are controlled by the National Commission for Nuclear Energy (Comissão Nacional de Energia Nuclear - CNEN). The objectives of this work to quantify the real lithium demand in the Brazilian market, considering that a large amount of lithium is indirectly imported in the form of the Li-ion batteries used in equipment such as mobile phones, cameras, tablets, notebooks and e-bikes, and to compare this demand with the current national production of LCE. Finally, some technological alternatives will be discussed, with the aim of increasing the competitiveness of the lithium industry in Brazil."

Jan 1, 2014