Search Documents

By Venkata Krishnaiah Yeddala, Sai Vivek Adari, Suresh Kumar Velugu

Assam cancer care foundation (ACCF) proposed the construction of hospitals and related facilities across 18 locations in the state of Assam-India. Tezpur is one among the 18 locations of Assam with high seismic risk. The strata at the site are comprised of mostly fine silty sands of lower SPT- N values. The water table is also encountered and ranging from 1 m to 2 m below EGL. Since the site lies in seismic zone V as per IS 1893, detailed liquefaction analysis is carried out for all five boreholes and indicates that soil is liquefiable and ground improvement is inevitable up to a depth of 15 m below existing ground level. To mitigate the liquefaction potential and enhance the seismic performance of the soil, ground improvement using stone columns by Wet top feed Vibro-replacement method is proposed. Also, the differential settlements can be avoided effectively under the raft foundation with Vibro Stone Columns. In this paper, field test validation results such as Pre and post-SPTs and ECPTs to access the extent of ground improvement, along with other information adopted in this project presented.

Nov 1, 2022

By Tian Miaomiao, Cheng Yin, Shen Jun, Yu Hao, Li Yafei

Vast amounts of waste drilling mud containing heavy metals is produced during oil drilling process, which causes great pollution to the environment. Therefore, it needs to be treated until it is harmless. This study uses industrial waste and Portland Cement stabilized waste drilling mud; the unconfined compression strength, leaching amount of Pb2+ and Cr6+ ions, and pore size of the stabilized soil were tested at different times during freezing-thawing cycles. The antifreeze performance of the stabilized drilling mud with industrial waste is discussed. The results show that the strength of the stabilized soil decreases with an increase in the number of freeze–thaw cycles. The strength loss of the stabilized soil after freeze–thaw cycles can be effectively reduced by increasing the industrial waste content, especially the content of phosphogypsum in the stabilizer component. Pb2+ ions and Cr6+ ions can be effectively stabilized by industrial waste. The results of the pores test prove that the compactness of stabilized soil solidified by industrial waste residue is greater than that of cement alone.

Nov 1, 2022

By Filippo Mira-Cattò, Andrea M. R. Pettinaroli, Elena Rovetto

"The construction of Powisle station of Metro Warsaw Line 2, in Poland, required the execution of two shafts next to an urban road tunnel adjacent to the Vistula River. The shafts were linked by three conventionally mined tunnels to be excavated 10 m below the water table level, into an upper sandy and sandy silty layer and a lower stiff clayey stratum. After a failed dig attempt under the protection of jet grouting and forepoling, it was decided to deal with the tunnels excavation problem by using the ground freezing technique as a temporary, non-polluting geotechnical treatment, keeping in service the upper road tunnel. The planning of the activities and the executive phases had a significant importance for the success of the work. For work scheduling reasons the mixed system was adopted, i.e. using both the liquid nitrogen system and the brine freezing method. The freezing process management, with a real time evaluation of the soil temperature measured by thermometric strings and an accurate monitoring of the overlying road tunnel structure, allowed the tunnel excavation and lining stages to be performed under difficult conditions, without water leaking from the frozen ground shell, within the expected times and saving extra costs.INTRODUCTIONThe new Underground Line 2 in Warsaw connects the eastern and western part of the town. One of the most critical interferences was the under passing of the Vistula river and of the Wislostrada motorway tunnel, a very congested motorway along the western bank of the river, with the construction of the new station Powisle. The construction of the station required the excavation of two shafts, using the top-down system with the creation of intermediate slabs while deepening the excavation.The shafts were used for the extraction of four Tunnel Boring Machines (TBMs), two approaching from the Vistula river side (east-side) and two approaching from downtown (west-side); in order to connect the two shafts was foreseen the realization of three tunnels, two for the underground lines and the central one for the exchanging passenger platform. These tunnels were underpassing the “Wislostrada Road Tunnel” and interfered with this tunnel foundation, which consisted of diaphragm walls (DW), the “barrettes” (Figure 1).Due to the variable geological conditions at the site, the first excavation stage, with a temporary underground support constructed of horizontal jet grouting columns and forepoling, caused the North tunnel face failure, that required an immediate filling of the empty cavities with lean mix concrete under the Wislostrada tunnel slabs. Thereafter, the recovering attempt with the grout injections could not be completed because of the development of heaves induced on the tunnel structures (Bringiotti et al. 2016). In those conditions the tunnel excavation with traditional technologies appeared to be very problematic, with high risk for the structural safety of the Wislostrada tunnel. This would have meant longer duration for the works and higher costs for the General Contractor as well as for the city Council."

Jan 1, 2015

By Sven Schröer, Lilma Schimmel, Dimiter Alexiew

"The Geotextile Encased Columns (GEC) deep foundation system for embankments on soft soils was introduced some 20 years ago and is now considered State-of-the-art worldwide.The GECs consist of compacted granular fill, similar to common gravel columns, with one decisive difference: they are confined in a high-strength low-strain flexible geotextile “cylinder” (encasement). This engineered element provides a very efficient tool to control and optimize the behavior of the system. GECs perform very well even in extremely soft soils ensuring bearing capacity (stability) and reducing settlements. Due to the encasement, they a lso provide high lateral ductility. A wide range of fills including sands can be used.The remarkable reduction of vertical stresses in the soft soil surrounding the GECs results in a decrease of lateral pressure as well. Such reduction combined with the lateral ductility allow GECs to be also used for lateral pressure-relief adjacent to sensitive foundations, e.g. rigid piles. The application of GECs as lateral pressure relief was recently used in Brazil and Germany where bridge abutments were built on concrete reinforced-piles. The GECs below the bridge approaches and adjacent to the piles decreased the lateral pressure to acceptable values.This paper presents two case studies for which the most relevant parameters, the geotechnical conditions, specific problems, engineering philosophy, final solution and lessons learned are discussed. Furthermore, instrumentation programs were applied in both projects. The most important results in terms of displacements and stresses are shown, evaluated, summarized and commented upon, focusing on the lateral stress-relief, followed by conclusions and recommendations."

Jan 1, 2016

This specification, along with the drawings, encompasses all designs, materials, products, accessories, tools, equipment, services, transportation, labor and supervision, installation techniques, and testing procedures required for the installation of soil nail excavation support or earth retention systems. This is a Guide Specification designed to assist in the development of project specifications for soil nail excavation support and earth retention systems. This Model Specification is based on generally accepted industry standards but may require modification by the specification writer to accommodate unusual and/or unforeseen site and subsurface conditions and the particular circumstances of the project. Care must be taken to avoid internal inconsistencies. It contains language allowing for a Contractor-Designed Soil Nail Wall, which would be removed if the design is provided by the Owner (e.g. See Sections 1.2 and 4.1).

Jan 1, 2010

By P. V. Chandramohan

"In ports, piled berths are designed and constructed for berthing of ships with a finite draught. Piles in a bridge foundation also have a large free stand above scoured level. The piles of these structures have to withstand large horizontal forces imparted by the impact of the approaching vessels or due to longitudinal and transverse action in a bridge. It is also imperative that these piles have to project out of the dredged / scoured bed. These piles are normally designed as slender compression members subjected to bending also. They are subjected to vertical load tests for assessing the soil resistance. Lateral load tests, as a rule, are also stipulated. IS and IRC codes stipulate a deflection criteria for lateral load test to arrive at the capacity. These tests are usually conducted on a working pile by jacking out two piles. At the time of the test, pile will be free headed. But in service, piles are fixed head. There is a large difference in deflections between a fixed head and a free headed pile. Besides, a free headed pile will be subjected to a much higher bending moment than the fixed head one. This will put the working test pile under risk of breaking during the test. The problem is analyzed with case studies. INTRODUCTION Vertical capacity of piles is assessed by static formulae. This formula is based on the soil properties obtained from random soil exploration and laboratory and in-situ testing. Since soil is not a homogeneous medium, properties can vary. The design parameters taken for computations may be different from the ones at the interface of the pile with the soil. The best way is to find out is by a load test. The code IRC:78-2014 has rightly stated that initial load test is part of the design process. This is true with the vertical load test. But there are certain problems with the purpose and inference of the lateral load test. In both the tests the criteria for acceptance is the quantum of movement of the point of application of the load. In the former, the movement is vertical and depends more on the compression of the soil than the compressive strain in concrete. But in the latter, this movement is partly on account of the flexural rigidity of the pile and partly due to the horizontal compressibility of the soil. The role of rigidity of the pile is more when compressibility of the soil is higher. Lateral load test is done by jacking one pile against another because it is difficult to get an independent horizontal reaction. Please see Fig.1 Photo."

Jan 1, 2015

By Paul Thurlow, Richard K. Lipscombe

The measurement of deflection of designed diaphragm walls is critical for near real time information to assess wall and soil behaviour as the internal area is excavated in a controlled manner. Data enables the site team and designers to check performance of the design, which is linked to safeguarding the site and the external stakeholders.This paper documents the use of Shape Accel Arrays at the Tottenham Court Road Western Ticket Hall during excavation and propping within the diaphragm wall for the Crossrail project. It shows how the data obtained was used within the site settlement management plan to assist in the control of the works and the information used for Value Engineering purposes that benefitted the project.The use of Shape Accel Arrays for measuring the deflection of retaining walls is not commonplace in the UK construction industry, with the Tottenham Court Road Western Ticket Hall being one of the first times they have been used in such a way. A detailed analysis of the data obtained from the instruments has been undertaken, and compared to the results obtained from the manual inclinometers that were read next to the SAAs. The advantages of the relatively new SAAs have been discussed, as well as other applications of the instrument.

Jan 1, 2017

By Filippo Maria Leoni, Alessandro Bertero, Gianluca Pianezze

"As part of the Southeast Louisiana (SELA) drainage program, designed by the U.S. Army Corps of Engineers (USACE) to reduce flood damages in the City of New Orleans and surrounding parishes through the construction of new pumping stations and better drainage canals, the SELA-22 project entailed the installation of a concrete covered canal along Jefferson Ave. and Prytania Street, in a highly urbanized portion of Uptown New Orleans, LA. The scope of the required soil improvement was to replace the soil between two parallel lines of sheet piles with a soil-cement mass to eliminate underseepage and provide structural support for the concrete culvert. The USACE selected the jet grouting (Jet Grout) technology for the construction of the bottom plug. The bottom plug is between 18 and 21.5 ft thick with a maximum depth of approximately 40 ft, for a total length of approximately one mile. The treated soil comprised soft clays and silts with occasional presence of sands. Project specifications required 100% area coverage, a 28-days unconfined compressive strength of 100 psi and hydraulic conductivity of 1x10-6 cm/s, to be verified by testing specimens from cored samples. The specialty geotechnical contractor proposed to accomplish the task utilizing their proprietary and innovative elliptical bi-fluid Jet Grout technology, and elected to perform a pre-construction bench scale laboratory mixing program to determine the most suitable grout mix features (i.e. binder type and proportions, binder content, etc.) to be applied in the subsequent field test and production stages. This paper will summarize and compare the results obtained from the different pre-construction and construction stages; interpretations of the data will be provided, along with general considerations regarding the effectiveness and significance of bench scale testing for jet grouting applications.INTRODUCTIONIn general, the effectiveness of the construction parameters in any ground improvement work depends largely on the physical and mechanical properties of the soil to be treated. Therefore, well designed laboratory and field test programs, aimed to disclose the interaction between the site-specific soils and the mixing parameters, are essential to achieve the desired end product."

Jan 1, 2016

By A. Daugiala, D. Coleman

In 2014 the New York State Department of Transportation (NYSDOT) awarded a Design-Build contract to the joint venture team consisting of Skanska which is the managing partner; Kiewit Corporation and Ecco III (SKE) and HNTB as the lead design firm. The design build team employed methods to provide schedule savings and commercial benefits to the owner NYSDOT. This paper presents the design approach and construction methods used to accelerate drilled shaft installation supporting the main span foundation for the cable stayed bridge. The drilled foundation contractor Underpinning and Foundation Skanska, a division of Skanska was responsible for assisting with design, budgeting and construction of the drilled shaft foundation construction. As part of the Request for Proposal (RFP) bid process, Alternate Technical Concepts (ATC) was encouraged by the NYSDOT. The JV team proposed an ATC which involved a scaled production shaft testing method to simulate the ultimate load level, commonly referred to as the “Chicago Method” was used in the rock socket employing the Osterberg Cell (O-Cell) testing procedures. To the authors knowledge this was the first NYSDOT project where this approach was utilized on a Demonstration/Production installation to validate construction procedures and load bearing capacities. Construction procedures, challenges and solutions are discussed in detail. Upon completion of successful drilled shaft construction, concrete integrity is verified using two methods – Cross Hole Sonic Logging (CSL) and Thermal Integrity Profiling (TIP). A comparison from the contractor’s perspective is provided. Finally the drilled shaft rock socket is tested to ultimate end bearing values while rock socket side shear stresses are not exceeding the service level loading. Lateral load test was also a RFP requirement; the test arrangement and performance are discussed in detail as well. The Kosciuszko Bridge location poised unique geotechnical challenges on many levels shifting towards an extreme boundary of parameters encountered in New York City Area for drilled shaft construction. The JV team and specialty drilled shaft contractor actively participating in the shaft design and construction practice coordination and working with NYSDOT yielded a successful foundation solution which provided cost and schedule savings to the project.

Jan 1, 2016

By Joint Micropiles Committee

"The three types of specifications which are used for micropile work are: • Performance Specifications: The contractor is permitted control over certain design and/or construction procedures but must demonstrate to the owner through testing and/or certification that the final product meets the specified performance criteria. This method allows and encourages the contractor to provide a competitive and/or innovative micropile design within the framework of the overall design requirements. The responsibilities for the work are shared between the owner and the contractor. • Open Specifications: These leave the scope and design of the installation up to the micropile contractor. This method is the most common for securing bids on temporary micropile work. The responsibility for design and performance is clearly placed on the contractor. Open specifications are not recommended for permanent applications. This method allows the contractor to select the most economical micropile system. • Prescriptive Specification: The Owner describes specific procedures that must be followed, but which may not necessarily describe the objective of the work. When prescriptive specifications are used, the owner is responsible for the proper performance of the system. The contractor is responsible for satisfying the details of the specifications.Performance specifications are the most common and best reflect the challenges and interests of micropile technology and applications.The owner, designer and contractor will together be responsible for the tasks associated with the design, installation, acceptance, and performance of the micropiles. The installation of micropiles requires specialized equipment, techniques, and appropriate workmanship. Not every detail of the work can be specified, and not every potential problem can be anticipated. Therefore, a contractor who has demonstrated experience in micropiles must be selected to execute the work required."

Jan 1, 2004

By Donald Bruce

The three types of specifications which are used for micropile work are: ? Performance Specifications: The contractor is permitted control over certain design and/or construction procedures but must demonstrate to the owner through testing and/or certification that the final product meets the specified performance criteria. This method allows and encourages the contractor to provide a competitive and/or innovative micropile design within the framework of the overall design requirements. The responsibilities for the work are shared between the owner and the contractor. ? Open Specifications: These leave the scope and design of the installation up to the micropile contractor. This method is the most common for securing bids on temporary micropile work. The responsibility for design and performance is clearly placed on the contractor. Open specifications are not recommended for permanent applications. This method allows the contractor to select the most economical micropile system. ? Prescriptive Specification: The Owner describes specific procedures that must be followed, but which may not necessarily describe the objective of the work. When prescriptive specifications are used, the owner is responsible for the proper performance of the system. The contractor is responsible for satisfying the details of the specifications. Performance specifications are the most common and best reflect the challenges and interests of micropile technology and applications.

Jan 1, 2004

By Dennis Nottingham

Spin-fin pipe piles can develop large loads in tension, thus have evolved as a foundation product of great potential. Currently, over 500 spin-fin piles have been used successfully in dolphins, docks, buildings and bulkheads. Spin-fin piles are pipe piles with plates welded near the tip at a batter-in-screw fashion. Thus, as the pile is driven, the pile screws into position. Tests show this pile type to have highly unusual stress/strain relationships, wherein plunging failure is usually never reached either at normal or large deformations. Tension capacity can approach pile capacity in bearing; thus, large reserves are usually available for tension. Tests have been performed on 8-5/8-inch to 24-inch-diameter piles in silt, sand, and gravelly soil, to provide a broad spectrum of data.

Jan 1, 1990

By Rudolph P. Frizzi

"Abstract Pile design for building structures in the United States is typically performed by: 1) investigating and assigning engineering parameters to the respective ground bearing materials, 2) calculating ultimate pile to ground (geotechnical) capacity which is then reduced by a Safety Factor deemed appropriate by a registered Design Professional thereby arriving at an allowable pile geotechnical pile capacity, and 3) determining the required pile structural section using allowable pile section material properties. It is advantageous to use a Working Stress Design Method (WSDM) approach as one system of loads (service loads) are used in both the geotechnical and structural evaluation. There are a variety of methods used to determine the ultimate and allowable geotechnical capacity, and Building Codes often require a registered Design Professional to determine the appropriate method(s) and capacities. The International Building Code is the Code typically referenced in building design and construction in the United States. Structural design usually follows Building Code requirements and Allowable Stress Design (ASD) procedures. As design of the overlying structure typically follows a Strength Design Method (SDM) approach using factored loads, in some cases piling is first designed for pile-to-soil interaction using service loads, followed by evaluating the pile geometry for factored loads. Construction is the finalization and implementation of the designed piling. As such, project-specific technical specifications are typically developed by a registered Design Professional such that a project Owner can bid, buy, and instruct a Contractor as to the desired piling work and acceptance criteria. There are several Industry groups, including DFI, PDCA, ADSC, and ACI that provide guidance documents which the registered Design Professional can refer to in developing the piling technical specifications. It is the author’s opinion that the registered Design Professional is best suited to observe and verify the piling installation; many Building Departments require verification and documentation by a registered Professional as a condition of final acceptance.INTRODUCTIONPile design for building structures consists of: investigation, design, specification, and verification. In major metropolitan areas within the United States, Building Codes typically identify minimum requirements for each of the above steps. The International Building Code (ICC, 2012) is the Code typically referenced in building design and construction in the United States. Recognizing the ground conditions as well as piling construction means and methods can vary on a site-by-site basis, latitude is given to the registered Design Professional and Contractor to optimize the piling system for the respective project conditions. Field testing and quality control / assurance measures are typically implemented to verify the design intent is attained for the production pile elements."

Jan 1, 2014

By Marlion T. McQuinn

This paper will discuss the design, construction, and performance of the support of excavation on the Dulles East and West Automated People Mover Tunnels and Station projects. The elements of the system included drilled soil nails and rock anchors with reinforced shotcrete to the excavated face. We will discuss the geotechnical characteristics, design and construction considerations, loading criteria, construction techniques, schedule constraints, and performance of the support of excavation system. In consideration of the conference theme, there will be a discussion of the application of the real-time instrumentation monitoring program. The project team worked to design and install approximately 710,000 square feet of shotcrete and 19,000 soil nails/rock anchors as well as excavate over 720,000 cubic yards of rock materials within 15 months and in such a manner as to minimize the disruption to airport passengers and operations.

Jan 1, 2006

By Ronnie Melker, Joel Webster, Daniel Belardo, Thomas Hyatt

Quality assurance of drilled shafts is highly dependent upon the construction practices used during the excavation and concrete placement process. When performed under slurry, challenges are presented in maintaining borehole stability and placing a uniform and continuous concrete column. An integral part of the construction operation is to evaluate the as-built integrity to verify the drilled shaft is capable of safely transferring the required loads to the subsurface. One such case is exemplified by a project involving the expansion of an existing public transit rail line. The expansion required the construction of a new bridge bent supported by seven 5-ft diameter drilled shafts of various lengths. The specifications for the project required both Cross-Hole Sonic Logging (CSL) and Thermal Integrity Profiling (TIP) for drilled shaft integrity evaluation. Both of these post-construction non-destructive tests (NDT) are designed to detect anomalies or the presence of regions with reduced concrete quality. However, the implementation and methodologies of performing each of these NDT methods are significantly different. Cross-Hole Sonic Logging uses ultrasonic signals emitted from a transmitter in one access tube to a receiver in another access tube. Thermal Integrity Profiling measures elevated concrete temperatures during the curing process using embedded thermal wires. Both test methods require different access details and therefore have different costs associated to the contractor or owner to perform. This paper provides a detailed comparison of these NDT methods as performed on these seven drilled shafts. The associated financial and time costs to perform each method are compared and the results are discussed in detail. INTRODUCTION Drilled shafts are a fundamental deep foundation element that can be designed to resist large bending moments as well as to transfer large compressive axial loads through weaker upper soils to competent soils or rock below. Often times when the upper soils are very soft, lateral support by casing or slurry, or a combination of both, may be used to hold back the softer soils from collapsing into the hole before concrete has been placed. Due to the blind nature of drilled shaft construction and the qualities issues that may arise during the placement process, it is essential for design engineers to specify non-destructive testing (NDT) to assess the quality of the as-built drilled shaft. CSL and TIP testing are two NDT methods designed to detect areas of lower quality concrete or soil inclusions throughout the length of the drilled shaft and determine its overall quality. Each method uses different technologies and methods to achieve the results required to determine the as-built condition of the drilled shaft.

Jan 1, 2019

By Joseph T. Coe, Siavash Mahvelati, Alireza Kordjazi

This paper introduces recent advances in stress-wave NDT systems for use in assessments of in-service foundation integrity and drilled shaft construction. The primary results of the laboratory experiments are very promising, as the acquired image was capable of differentiating changes in pile cross section as low as 0.3 cm. The preliminary results with the same hardware components on a relatively large scale cemented sand model were also promising. A brief overview is provided of both systems including hardware, survey methods, and data processing techniques, followed by a discussion on application of the results to QA/QC of deep foundations. INTRODUCTION There are two main applications in which current QA/QC NDT technology fails to provide sufficient information regarding deep foundation conditions: (1) detection of flaws in outside cover concrete of drilled shafts and corrosion in steel piling; and (2) evaluation of anomalies beneath the bottom of drilled shaft excavations. Previous studies have demonstrated the capabilities of high frequency stress waves for geotechnical and foundation evaluation purposes (Lee and Santamarina 2005; Coe and Brandenberg 2010; Coe and Brandenberg 2012; Coe and Kermani 2016). Higher frequency waves can visualize smaller anomalous features at the expense of higher attenuation and smaller propagation distance. Therefore, the goal of this study was to advance the state of NDT practice by development of a prototype high resolution stress-wave imaging system as proof-of-concept. The equipment and hardware were modular, which allowed simultaneous development of two system configurations for application to in- service foundations as well as drilled shaft excavations during construction. Results are presented based on two large scale soil models. The first laboratory model simulated section loss in an in-service steel pipe pile and drilled shaft foundation (Fig. 1a). The second model simulated anomalous conditions beneath drilled shafts excavations as might be encountered in areas with significant karst (Fig. 1b). For both models, evaluation of foundation conditions relied on the propagation of small amplitude seismic stress waves using hardware similar to those described in Coe and Brandenberg (2010) and Coe and Brandenberg (2012).

Jan 1, 2018

The intent of this manual is to provide guidelines for inspectors of drilled shaft construction otherwise referred to as drilled piers, caissons or bored piles. It should also be helpful to train beginning geotechnical engineers with limited first hand experience or for geotechnical engineers who are training inspectors. It is expected that the general guidelines and procedures described here will be supplemented by local geotechnical engineers working in a particular region based on local practice and experience. Since drilled shaft construction procedures vary widely based on local geology and size of project, an all-inclusive manual is not considered practical. This manual focuses on traditional topside inspection for routine drilled shaft construction. Other inspection and evaluation methods that rely on electronic equipment are available, but these methods require extensive training and experience in the interpretation of results. These more sophisticated methods of drilled shaft inspection and evaluation are common in construction, but they are usually provided by specialty subconsultants. The subconsultant will typically submit a report for each shaft, which will be reviewed by the geotechnical engineer. Other manuals are available to describe the electronic methods of drilled shaft inspection.

Jan 1, 2004

By Walter Ensinger

Special foundation works is one of the most innovative sectors in civil engineering and construction. Both engineering techniques and construction machinery are undergoing continu­ous further development. These developments are providing ways to meeting the world-wide requirement for special geotechnical works even faster, even better and more efficiently. Unfortunately, accident prevention organisations have had to realise that the figures on in­dustrial accidents in special foundation works are still above average in number. The Safety & Environmental Working Group of the EFFC thereupon started to carry out a survey on acci­dents occurring in this sector and used this information as a basis for the preparation of acci­dent statistics and an accident analysis. The objective of this undertaking is to determine key accident occurrences and their causes and to consequently determine measures for improved health and industrial safety.

Jan 1, 2002

By Roger Frank

"Abstract After noting the importance of standardization for piles, the European system is described (execution, tests and design, etc.). Some important aspects of Eurocode 7 are outlined (like the role of pile load tests). Finally, the calculation methods in the recent French standard for the design of piles following Eurocode 7 are shortly addressed.Importance of standardization for piles Like for other fields of geotechnical engineering, pile engineering is a complex art. For piles, the challenges are particularly numerous and many things must be mastered properly: - the soil investigation must be serious and adequate (for instance, deep enough!);- the choice of the pile type and the assumed behaviour must be assessed in order to reach a safe and economic design of the overall foundation;- the execution itself (construction and/or installation) deserves special attention and must follow strict state-of-the art rules.The geotechnical engineer, in charge of the design of a pile foundation, must have in mind the parameters linked to the variety of soils, of soil conditions and of pile types. A wide range of strong environmental issues are also to be considered: minimum disturbance during the execution processes, long-duration friendliness of the “inclusions” into the ground (to avoid pollution of the soils and waters, for instance) and respect of the neighbouring structures.Pile engineering plays in a world which is constantly moving and progressing: constructions expand in new difficult areas, actions on piles are more and more important, new execution techniques of piles are developed, research into the complex behaviour of pile foundations has no end, etc. Our views on how piles and group of piles really work are constantly evolving!"

Jan 1, 2014

By Chandrasegaran, Tamilmani

"This paper describes a case study of a retaining wall structure using a diaphragm wall to construct a stilling basin at Tanjung Bin T4 power plant in Johor Bahru, Malaysia. The stilling basin is part of the Phase IV (T4) 1x1000MW power plant’s offshore cooling water discharge culverts. The site is located close to the sea with 5m of fill on top of very soft sediments of marine origin up to 20m thick underlain by fluvial clay and metasedimentary rock. Stringent wall deflection criteria and construction program dictated adopting an efficient solution with 800mm thick diaphragm wall supported by permanent top support as the temporary prop and improved horizontal restraint provided by deep mix piles acting as a slab (ground improvement layer) below the final excavation level. The depth of excavation is about 10.12m from the existing ground level. The proposed solution kept the wall deflection below the limit of 0.7% of the depth of bulk excavation and avoided additional props leading to faster completion of the structure. With unsymmetrical loading behind the retaining walls, 2D finite element analysis was carried out to assess the wall deflection and stresses in the wall and the grout layer below. The diaphragm wall is instrumented to monitor the behavior and the findings are discussed in the paper.INTRODUCTIONConstruction in soft marine clay has always been a challenge to the engineer because of its very low shear strength and its sensitivity to disturbance. In the case of excavation projects the problem becomes even more complicated with development of excess pore pressure during excavation. Marine clay with its low shear strength and lesser passive resistance, generally leads to large wall movements and settlement behind the wall. Increased passive resistance coming from increased number of props is useful but has its limits and it is no longer the most effective way in containing or reducing the wall movements or forces in the wall. One of the solutions to these problems is to improve the soil shear strength by means of ground improvement infront of the wall at an elevation most appropriate to maximize wall performance. There are several methods adopted in improving a soil layer including mixing additives to the ground to improve the shear strength to partially replacing the weak soil while others are fully replacing the weak soil. This paper discusses the case study of approximately 10m of excavation in soft marine clay using 800mm thick diaphragm wall supported by Deep Mix Piles (DMP) being used to improve soft marine deposit to form a slab just below the formation level and thus improving passive resistance significantly. The ground improvement layer helped to reduce the wall forces and deflections making it possible to remove the need for additional temporary props leading to significant savings is time and productivity. The paper presents the various options explored before this method is adopted, the design approach, instrumentation data and the monitored results."

Jan 1, 2015