Search Documents

By Dr Karsten Galipp, Kai-Julian I. Hendler, Prof. Manuel G. Pinheiro, Dr Peter J. Bourne-Webb

With a share of approximately 11% of global greenhouse gas emissions, the construction industry contributes significantly towards climate change. This is why construction projects should not only be assessed on costs and technical solutions, but also on their carbon emissions. Life Cycle Assessment (LCA) is a tool which can quantify the environmental impacts of a construction project over its entire lifetime. The objective of this study was to determine the carbon footprint of three types of quay wall structures, namely sheet pile combi-walls, open piled decks and caissons using an LCA approach. Each of these quay walls were studied under the same boundary conditions, such as design life, ground conditions, dimensions, location and so on. The analysis showed that the sheet pile wall has the lowest carbon footprint whereas the open piled structure has the highest. Furthermore, it could be shown that the largest share of greenhouse gases (approximately 80%) is emitted during the production of construction materials. The transportation of materials and construction activities each contributed under 12% to total emissions. The sensitivity analysis showed that with innovative approaches, such as adapting the concrete mix design, the carbon footprint could be reduced by 26% to 40%.

May 1, 2022

By Ian Vaz, Takefumi Takuma

"The New Orleans area has been repeatedly flooded by major storms and hurricanes since its French colonial era. After severe flooding in May 1995, the U.S. Congress authorized a massive flood protection project called the Southeast Louisiana Urban Flood Control Program (SELA) in 1996 to improve interior drainage in Orleans, Jefferson, and St. Tammany parishes. However, the project was not fully funded before the landing of Hurricane Katrina in 2005 and Hurricane Rita, which breached many of the area’s levees and flooded 80 percent of the city. Finally, the project was fully funded in 2008 and has been worked on towards its 2017 completion. Another large project simultaneously worked on in the area is the Hurricane and Storm Damage Risk Reduction System (HSDRRS). This system was designed for a 100-year level of flood risk reduction. One particular project within the HSDRRS rendered successful due to an unconventional method of pile driving that was utilized to install sheet piles to reinforce an existing concrete I-wall. This paper will discuss how and why this non-vibratory method of sheet pile installation allowed the project to be successfully completed ahead of schedule.INTRODUCTIONSteel sheet piles were utilized on many of the SELA and HSDRRS projects for permanent cutoff walls under concrete I-walls or T-walls or for temporary earth retaining walls of drainage structures. Although the SELA Project was established in 1996 after severe flooding the year before, hardly any work was done on it until the two catastrophic storms Hurricanes known as Katrina and Rita triggered its revival. These two hurricanes also triggered the HSDRRS soon after the storms’ devastation. The SELA project authorized to improve interior drainage systems while the HSDRRS project was authorized to raise or restore levees and floodwalls mainly along Lake Pontchartrain, the Mississippi River, and Lake Borgne in addition to other areas. Figure 1 shows the SELA Projects that have been completed, are still under construction, or approved for construction. The projects fully highlighted in yellow within the map specified the press-in piling method. These improvements included drainage systems, pump stations, surge walls, and outfall canals as enhanced protection for future storms similar to Hurricane Katrina that caused so much damage by inundating the New Orleans area in August and September 2005 respectively (Facts and Figures, 2012). The completion of these projects were the responsibility of the U.S. Army Corps of Engineers, New Orleans District.Due to the fact that many of the projects were in densely populated areas, the Army Corps of Engineers specified a non-impact, non-vibratory press-in piling method for driving and extracting sheet piles for many of the projects to mitigate noise and vibration impacts. The soft soil conditions in the New Orleans area was also a contributing factor in the Army Corps of Engineers’ decision to specify this piling method due to the risk of settlement for existing historical as well as modern structures. In addition, there were other projects that elected to use the press-in method without any contractual requirements. One of these projects was the Inner Harbor Navigational Canal Reach II Emergency Interim Repair which was part of the HSDRRS project that has been under construction since its authorization in 2005 (Facts and Figures, 2012)."

Jan 1, 2017

By Z. Y. Ding

This paper emphasize two points in piled wharf design which are important than structure calculation. First, during design of piled wharf on soft stratum, the bank slope stability is the first important item. Second, the live load, the backfill and the original ground's settlement will influence the wharf structure causes cracks. Two practical examples were illustrated.

Jan 1, 1991

By Rüdiger Wunsch

The new high speed Vienna - St.Pölten line and the Lainzer tunnel are to be connected to the existing Western railway line in Vienna. This involves building an underground cut and cover branching tunnel which will be connected to the Western railway line by ramps. A key structure is the Herzmansky Street tunnel, which has a length of some 820m. It is to be constructed as a cut and cover tunnel using the top down method. The walls of the tunnel are designed as a water resistant structure consisting of double walls, an outer wall of bored piles and an inner reinforced concrete wall. The bored pile wall will be used as a temporary retaining wall during the construction phase and will also be a structural part of the per­manent tunnel wall. The retaining walls of the open pit, which will have a depth of up to 14m and a width of 12m, were investigated as a non-contiguous bored pile wall and overlapped bored pile wall. Preventing ground water from penetrating into the pit is of paramount importance. The high ground wa­ter level is the determining factor for the dimensioning of the bored pile wall and results in the require­ment for a water resistant concrete structure. It has been necessary to adopt adequate measures, therefore, in order to reduce the hydrostatic water pressure during the construction phase, assuming economical pile dimensions.

Jan 1, 2000

By Andres M. Baquerizo, Jeremiah J. Filjones, Nicholas Feldt

The Estates at Acqualina located in Sunny Isles Beach, FL, is comprised of two, ocean-front, 50-story, luxury towers with podiums and villas. With city regulations now requesting that above-grade floors be limited to commercial or residential units, parking facilities for the tower structures were situated within two levels of underground basement parking. However, ensuring dry excavation through south Florida’s highly pervious limestone, immediately adjacent to the beach where the groundwater table is very shallow, can be extremely challenging and costly for developers. In recent years, significant advances have been made to overcome this challenge with the innovative use of deep soil mixing to create a “dry hole”, assisting in the construction of foundations and underground usable space for parking, storage, etc. The “dry hole” system includes a soil mix bottom seal, with soil mix secant pile walls in combination with auger cast deep foundation elements to support the future structure. This approach enables groundwater control to greater depths than can be achieved by conventional sheetpiling and dewatering. For the Estates at Acqualina, a successful turnkey, design-build joint venture between two foundation and geotechnical contractors resulted in a dry excavation to 34 ft (10.4 m) below grade and to a record- breaking auger cast pile depth of 182.3ft (55.6 m), all within an aggressive 26-week schedule to deliver the “dry hole” excavation for the first tower. This presentation will discuss the logistics, quality control, design, and safety for the different techniques involved. INTRODUCTION AND BACKGROUND The Estates of Acqualina is a pair of 50-story luxury towers located on Sunny Isles Beach in Florida with a two-level underground basement for parking. The project’s location just steps away from the Atlantic Ocean, geology, and high-water table created a challenging project. The owner, Trump Group, contracted the joint venture of HJ Foundation and Hayward Baker (HJ/HB) to design-assist-build a system to control the groundwater, allowing the 2-story underground parking structure to be constructed. In order to accomplish this task, the JV utilized an installation technique known as deep soil mixing. This technique mixes the in situ material with a cement slurry to create a very impermeable material called “soilcrete”.

Jan 1, 2019

By P. A. Neill, O&apos

The caisson foundation for Vent Building No. 6, at the southern landfall of Boston's Third Harbor Tunnel, was installed inside an unbraced concrete cofferdam 250 feet in diameter and about 70 feet deep. As a spectacular engineering feat, the cofferdam itself certainly ranks first. However, the foundation work within was no routine caisson job and made its own contribution to the state of the art. Comprised of 5 ft. diameter caissons socketed 10 to 16 feet in sound rock, it posed serious challenges in logistics, space limitations and time, requiring development of unique, purpose-made equipment. The unexpected discovery of significant depths of shattered rock overlying acceptable sound rock, along with other surprises of lesser import, compounded the problems. How these challenges were planned for, met and overcome is the subject of this paper.

Jan 1, 1994

By N. C. Matheson

The West's Shell Pile has been used on sites with very soft ground conditions for over 60 years. Fibre reinforced precast concrete shells 900mm long are threadled onto an internal mandrel which can be extended according to the depth driven to attain the load bearing resistance. On completion of driving the mandrel is removed leaving the precast shells to form a permanent lining to the cast insitu concrete core. To give resistance to high contamination, a tar based epoxy coat is sprayed on the outside of the shells or a flexible PVC liner is installed inside the shells to protect the core. Fundamental to the resistance to contamination is the quality of the precast fibre reinforced concrete shell, the mix design and method of manufacture. A series of detailed laboratory experiments were carried out using samples immersed in concentrated acid and sulphate solution. The long term effects of exposure to contamination is recorded in the case studies of existing piles at two gasworks sites.

Jan 1, 1989

By George Mylonakis

The curvatures and subsequent bending imposed to piles by the surrounding soil during the passage of strong seismic waves is studied. This type of bending develops even in the absence of a superstructure and is referred to as "kinematic bending", to distinguish it from bending imposed to piles by loads generated from the inertia of the superstructure ("inertial bending"). Although kinematic loading may be severe in the presence of sharp stiffness discontinuities in the profile and may lead to damage, it has received little attention by engineers. The scope of the paper is twofold: (i) to discuss some fundamental aspects of seismic pile bending, and (ii) to review some existing design methods. To this end, a dimensionless bending strain parameter (instead of the more commonly used bending moment), and a strain transmissibility function relating pile bending strain and corresponding soil shear strain are introduced. Numerical examples are also presented.

Jan 1, 2002

This work shall consist of furnishing and driving foundation piles of the type and dimensions designated on the plans or in the special provisions including cutting off or building up foundation piles when required. This specification also covers providing test piles and performing loading tests. Piling shall conform to and be installed in accordance with these specifications, and at the location, and to the elevation, penetration and bearing capacity shown on the plans or as directed by the Engineer. Except when test piles are required, the Contractor shall furnish the piles in accordance with the dimensions shown on the plans or special provisions. When test piles are required, the pile lengths shown on the plans are for estimating purposes only and the actual lengths to be furnished for production piles will be determined by the Engineer after the test piles have been driven. The lengths given in the Engineer's order list will include only the lengths anticipated for use in the completed structure. The Contractor shall, with-out added compensation, increase the lengths shown or ordered to provide for fresh heading and for such additional length as may be necessary to suit his method of operation.

Jan 1, 1989

By John W. M. Lambert

This paper describes the execution and the results of a new method to seal off leaks in water retaining constructions. The new method, called BioSealing is based on activating the bacteries, present in soil and groundwater. The method was tested under field conditions in 2004 and applied at the HSL aqueduct of the 'Ringvaart Haarlemmermeer' in 2005.

Jan 1, 2006

By Donald A. Bruce

"Abstract The Deep Mixing Methods (DMM), in their current forms, have been employed in the United States since 1986, although an earlier version had seen service from 1954. The earlier developments were strongly influenced by practices in the Nordic countries and Japan, while by the late 1980’s several DMM systems had been developed in the U.S. itself. Since then, DMM has continued its evolution, principally via the challenges of a series of large, landmark projects, but also via distinct, significant technological advances. This paper highlights the key points in the history of DMM in the U.S., and provides an overview of the different methods currently in use.In the BeginningIt is a common misconception that the history of applications of the Deep Mixing Methods (DMM) in the United States dates from 1986 when SMW Seiko Inc. — a subsidiary of Japan’s Seiko Kogyo Company — was established in the Bay Area. However, the author believes that Intrusion Prepakt Co.’s patented MIP (Mixed in Place) system had been used, albeit sporadically (about 30 projects are recorded), since 1954 (FHWA 2000, 2001). Ironically, by 1961 this single auger method had been extensively used under license in Japan for excavation support and groundwater control — by the Seiko Kogyo Company. By 1972, the original MIP technique had been succeeded by more advanced Japanese methods, involving multiple augers. Intrusion Prepakt have long since become defunct.The first systematic studies of contemporary Deep Mixing Methods in Japan began in 1967 when the Port and Harbor Research Institute of the Ministry of Transportation began laboratory testing using granular and powdered lime for treating soft marine soils. Fundamental studies continued through the early 1970’s, by which time the development of industrial scale equipment was well advanced, having its first application on a marine trial near Haneda Airport. Coincidentally, laboratory and field research also began in 1967 in Sweden (“Swedish Lime Column Method”) for treating soft clays using unslaked lime. Reportedly the progenitor was a Norwegian, Kjeld Paus, who had made observations on fluid lime columns in the U.S. It would seem that developments in Japan and the Nordic countries proceeded independently until 1975 when the technology leaders from each group (Broms and Boman; and Okumura and Terashi, respectively) presented their — very similar — findings at a conference in Bangalore, India. Limited technical exchanges ensued thereafter.Whereas the Nordic developments continued to focus on the use of dry reagents (cement and lime) and relatively light equipment compatible with operating on and in very soft clays and organics, the Japanese progressed into the use of fluid reagents (cement-based grouts) and heavier equipment for both marine and land-based projects. Thus, by 1986, there were a large number of proprietary (wet and dry) DMM systems in Japan, and a rapidly growing market already by then accounting for over 12,000,000 m3 of ground treatment."

Jan 1, 2014

By Martin B. Hudson, Daniel Brescia, Zhangwei Ning

Due to the complexity and sensitivity of surrounding environments, instrumentation and monitoring (I&M) is critical for many urban deep excavations. The objects to be monitored include shoring bulkheads, retained embankments, adjacent buildings and roads as well as underground utilities. However, there are also plenty of constraints on the implementation of I&M such as: congested site space, difficult access to instruments, coordination among multiple contractors, and installation permits for private or public properties. Because of these constraints, sometimes the implementation of the initially planned I&M is delayed, its scope is reduced, and/or the continuity of monitoring is interrupted. For these reasons, it is important to implement the I&M with robust and redundant capabilities while providing minimal interference to the project construction and schedule. This paper describes state-of-the-art I&M technologies including automatic motorized total station (AMTS) with camera and automatic leveling device, reflectorless AMTS and IoT- based wireless sensors based on a case study of an on-going deep excavation project. INTRODUCTION In urban environments, deep excavations requiring the construction of temporary shoring bulkheads are becoming increasingly common, with the associated need to provide protection of the surrounding built environment during construction. Protection of the surrounding environment requires planning, engineering, construction, monitoring, and excessive shoring movement mitigation. The I&M is a vital component of the deep shoring implementation. In public projects, geotechnical I&M is often placed within the general contractor’s scope, whereas the majority of deep excavations are privately undertaken. For those private developments, sometimes the developer contracts the geotechnical I&M directly with the project geotechnical engineer or by a geotechnical I&M specialist hired by the project geotechnical engineer. In either the public project or private development case, the effective deployment of the I&M system relies heavily on coordination and collaboration with the project contractor.

Jan 1, 2018

By Jan Pru?ka

This paper describes the sheet pile design for the Line C extension from Ládví station to the North of Prague. The first part of the paper describes the geological conditions and structural configuration of the project. Typical cross sections, the description of the construction stages, and monitoring are discussed. The second part of the paper focuses on the sheeting design method. It describes the method of dependent pressures, that is, how the pressures acting upon a structure depend on the deformation. The design process and verification methodology are described in detail with comparison of the results with in-situ monitoring.

Jan 1, 2011

By Robert W. Schaut

The use of micropiles is increasing for new construction and to retrofit distressed foundations in expansive soils. Typical micropiles in expansive soils have a lower section where the micropile grout is embedded in direct contact with the soil, and an upper section that is cased with rigid PVC pipe or other material to reduce the friction between the micropile and the surrounding expansive soil. In the upper cased section, the micropile grout is in direct contact with the inside of the casing. During construction, grout can flow upward into the annular space between the soil and the outside of the casing as the grout is tremied into the micropile. Thus, various interfaces may exist in a typical micropile, including soil-to-grout, grout-to-PVC, and soil-to-PVC. As the surrounding soil heaves, shear stresses are mobilized along the interfaces. The frictional characteristics of the interfaces are design variables that must be evaluated. For this study, an experimental program was conducted to evaluate the shear strength of the three interfaces listed above. Conventional direct shear testing was performed at a commercial testing laboratory. In addition, specialized testing was performed at Colorado State University (CSU). For the CSU testing, an interface testing protocol was designed using a modified triaxial cell to allow evaluation of the interface characteristics between rigid PVC and cylindrical specimens of grout or clay soil. It is shown that the shear strength of the soil-to-PVC and grout-to-PVC interfaces are similar, both of which are significantly lower than the shear strength of the soil-to-grout interface. This indicates that the use of a PVC casing in the upper portion of a micropile has a positive effect in reducing friction and the shear stresses resulting from expansive soil.

Jan 1, 2011

By Abu B. Siddique, Anthony S. Crincoli

"The New Jersey Turnpike Section 2 widening program consisted of widening between Interchange 6 in Mansfield Township, Burlington County and Interchange 9 in East Brunswick Township, Middlesex County. To accommodate large volume of traffic the roadway was widened from 6 to 12 lanes with major modifications performed at four interchanges. The Section 2, NJTA Interchange 6 to 9 Widening Program is a 4.2-mile section of Turnpike roadway which included a total of 12 new or modified structures. In order to facilitate the construction process Section 2 was divided into three construction contract packages. This paper will cover the last and final Contract T869.120.203 which is 1.7 miles in length. The work generally consisted of eight new ramps connection to and from the toll plaza to the new inner and outer roadways. New mainline bridges were constructed over several ramps. A new bridge was constructed to take northbound outer lanes traffic over two ramps along with new mainline bridges over Black’s Creek, Georgetown Road, and Laurel Run. In addition, a new bridge was constructed to take a ramp over Laurel Run and the existing U-turn Bridge was replaced with a new one.For Contract T869.120.203 a total of 74 five-foot diameter drilled shafts has been constructed to support all pier foundations for bridges. Three drilled shafts were tested using Osterberg Load Cells to verify the estimated shaft resistance during design phase. One Osterberg Load Cell test was performed on a demonstration (sacrificial) shaft and the other two Osterberg Load Cell tests were performed on production shafts. This paper compares the estimated total, side and tip resistances with corresponding measured total, side and tip resistances and provided recommendations for future design purpose.INTRODUCTIONTo accommodate large volume of traffic the New Jersey Turnpike Authority (NJTA) decided to widen Section 2, which included Interchange 6 through Interchange 9. The Section 2, a 4.2-mile section of Turnpike roadway that was widened from 6 to 12 lanes with major modifications performed at four interchanges.The New Jersey Turnpike Authority (NJTA) procured AECOM to perform engineering services for the final design of Section 2, NJTA Interchange 6 to 9 Widening Program. Section 2 is a 4.2-mile section of Turnpike roadway that will widen from 6 to 12 lanes and will include a total of 12 new or modified structures. It encompasses modifications of the existing and the design of four new ramps at Interchange 7. The project also includes the modification of two local roads over the mainline, two local roads under the mainline, two maintenance U-turns, and retaining walls. In addition, the project consists of the design of noise walls, sign structures, storm water management basins and the more typical drainage, utilities, lighting, roadway, ROW, and signing and striping design."

Jan 1, 2015

By Christopher M. Kenney

Augered-cast-in-place (ACIP) piles have been utilized on commercial projects throughout many parts of the country for years, but are only beginning to be scrutinized for use on major infrastructure projects and other critical structures in some regions. Numerous engineers are aware that ACIP piles are an economical foundation alternative, and many technical papers have been presented that provide reliable methods of estimating ACIP pile load capacity. However, designers may not yet appreciate that the load-settlement behavior of ACIP piles is very similar to that of drilled shafts. This paper analyzes ACIP pile case histories from throughout the country and demonstrates that ACIP pile settlement under applied load is consistent, predictable, and very similar to the documented behavior of drilled shafts. This paper also presents a simple but accurate method of estimating ACIP pile settlement at the design load, and illustrates the need to estimate the equivalent diameter of the as-built ACIP pile when estimating pile behavior. Finally, this paper presents back-calculated values of the drained elastic modulus from the ACIP pile case histories that may be useful to those using more sophisticated methods of estimating ACIP pile settlement.

Jan 1, 2001

By Michael J. Brown

Load testing is important for controlling the quality of piled foundations. The Statnamic test is an alternative to existing testing methods with a load duration that lies between that for static and dynamic tests. Current methods of analysis offer excellent correlation between static and Statnamic tests for coarse-grained soils but often over-predict the capacity for fine-grained soils. Thus a calibration chamber is being used to produce instrumented beds of clay with reproducible properties. A model pile placed in the beds can be loaded at varying rates using a computer controlled servo-hydraulic system. Results from the modelling will be used to improve methods of analysis and govern the design of a full-scale study. Initial results suggest the rate effect can be represented by a power law relating pile velocity and resistance. Statnamic loading of the model pile produced large negative pore pressures in the clay bed.

Jan 1, 2002

By Emilie Lapointe, Fernando Famania

"A reliable determination of the in-placed cement factor, as defined by mass of cement over volume of final element of treated soil, allows the optimization of cement usage to achieve treated soil requirements. Cement determination tests were performed on soil-cement samples, both fresh (as per ASTM D5982) and hardened (as per ASTM C1084). This paper reviews the calibration work required for the D5982 determination of cement content by the heat of hydration method used on soil-cement samples obtained by wet-grabbing. Using the correlation curves in the field provides a rapid assessment of cement content hence optimizing the cement injection rate to match laboratory tests previously conducted. Cement determination tests on hardened soil-cement specimens from wet-grabs and cores were performed using the oxides method. Samples, both cored and wet-grabbed, were tested in a given cement-treated element, and in different soils to inform on the expected variation in cement content from field installation. Results indicate that both cement determination methods are valid for forensically determining cement contents and that they provide better assessment than the conventional field reporting methods. The methods can be used to optimise the cement usage as well as for Quality Assurance, especially when coring quality is poor.INTRODUCTIONThe degree of improvement, and inherent strength, which is attained in a deep-mixed soil is a function of many factors. The binder type, the existing soil, the mixing conditions and the curing conditions are the categories of factors influencing the strength of a given cement-treated soil as agreed by the deep mixing community and as summarized by the Coastal Development of Technology [CDIT] (2012). Given a site with existing soils and conditions requiring soil improvement using a given binder, the designer and/or contractor can control the mixing conditions. Mixing conditions are inclusive of the degree of mixing, mixing duration and the quantity of binder. Once a deep mixing method has been chosen to mix optimally the in-situ soil, the quantity of binder is the only remaining factor to be optimized. The quantity of binder, in the construction industry is commonly referred to as the field binder factor [ar] and defined by the mass of binder over the volume of soil treated with kg/m3 as unit. In research, the quantity of binder is referred to as the binder content [Cc] and expressed as a ratio of the mass of binder over the mass of dry soil mixed."

Jan 1, 2015

By Ashutosh S. Dhar

Cast-in-place piles were examined in this paper from the viewpoints of construction quality, axial capacity, and load-displacement responses. The results of ten 450 mm diameter (18? f) bored piles, installed in a soil deposit of silt to medium dense sand using the method of percussion drilling, were tested under static loads. The results of the pile load tests were used for evaluation of various design methods of calculating pile capacity. The study revealed that the design methods based on the concept of critical depth underestimated the ultimate skin fiction. Thus, the applicability of the critical depth concept for design of bored piles under the soil condition considered may be unreliable. The estimated skin friction factor, ß, was too low in these methods. The Tomlinson method and the Neely method provided the best prediction of the ultimate skin friction. The methods used for calculating end bearing resistance were found to provide a conservative estimate of the resistance. During pile load tests, a settlement of 5 to 6 mm was required for full mobilization of skin friction for the piles in loose sand, while larger settlements (> 10 mm) were required for piles in denser soil. The ultimate skin frictional resistance was observed to be low for piles in loose sand.

Jan 1, 2006

By Ray Schmahl

The Glenwood Canyon is a 13 mile long river gorge formed by the Colorado River approximately 2 miles East of Glenwood Springs, Colorado and approximately 150 miles West of Denver Colorado, (See Drawing #1). The canyon walls rise some 800 feet from the river elevation on either side of the river. The South-side river bank is occupied by the Denver and Rio Grande Western Railroad. The Northside is currently occupied by completed sections of Interstate 70 and US Highway 6. The railroad was built in the late 1800's and a hydroelectric power generating station was built in about the center of the canyon in the early 1900's. The Highway 6 platform was completed in the 1930's. The design and alignment for Interstate 70 thru Glenwood Canyon began in the early 1970's. The Highway thru Glenwood Canyon was designated a scenic Highway by the United States Congress, thereby allowing certain deviations from standard Interstate requirements. Environmentalists objections to the construction of Interstate Highways thru Glenwood Canyon resulted in especially careful design to avoid adverse environmental impacts. As a result, in many areas the new Highways will have restored the canyon to its more native configuration than what was the case in the building of the US 6 Highway platform.

Jan 1, 1990