Search Documents

By Fengxiang He, T. Meadowcroft, Yanjun Zhang

Slag from the zinc fuming furnaces contains about 3 percent zinc and 0.1 percent lead. The paper outlines several experimental techniques for recovering these components from liquid fumer slag. The simplest method, remelting followed by a hold period, indicated that a substantial fraction of the metal values was recoverable as a result of fuming into the gas phase, presumable by reduction of the metal ions by divalent iron ions. Following on from this, slag samples were equilibrated with copper, chosen because the activity coefficients of zinc and lead in copper are very low. This improved metal recovery, with substantial amounts of lead and zinc reporting to the liquid copper as well as to the fume. Application of an electrical emf across the slag-metal interface, using a graphite anode and a liquid copper cathode, resulted in further gains in metal recovery.

Jan 1, 2004

By R. V. Typliski, G. J. Labarre

"Hudson Bay Mining and Smelting Co., Limited, Flin Flon, Manitoba, has developed a metallurgical wastewater treatment system employing two-stage lime neutralization, sludge recirculation and conventional mechanical thickening.Laboratory investigations, initiated in 1970, led to the construction of a pilot-scale minewater treatment plant, at Schist Lake Mine, in early 1971. This plant, treating 600 cubic metres /day of wastewater containing 30-60 mg/1 zinc. demonstrated metal extraction efficiencies of 99% under normal operating conditions.On the basis of this pilot work, a second pilot-scale treatment system was established in 1975 at the Flin Flon metallurgical plant to treat zinc refinery process waste water. Through numerous improvements, including automatic con¬trol equipment, the system has evolved to a full-scale operation capable of treating 800 cubic metres/day of wastewater containing 4-11 gm/1 zinc. Treated effluent contains 0.2-20 mg/1 zinc. The hydroxide sludge produced returns to the metallurgical process for the recovery of metals while clarified effluent discharges to waste.With the system, Hudson Bay Mining has achieved its original goal: the reduction of environmental contamination, while realizing a return from metal recovery.IntroductionWith the goal of reducing environmental contamination, Hudson Bay Mining and Smelting began laboratory testwork, during the late 1960's, into the methods and technology for neutralizing and removing heavy metals from acid mine drainage. Based on lime treatment, early tests showed much promise and culminated in the construction of a pilot-scale test plant at Schist Lake Mine in early 1971.This pilot system utilized technology developed in laboratory studies, and related to work then underway by state authorities in Pennsylvania coal mines. The basic operation consisted of a lime slurry tank, baffle reactor and a free-settling basin. Through three summers of operation, the Schist plant, capable of treating 600 cubic metres/day of minewater, produced a heavy-metal extraction of 99% under normal conditions. Although successful in proving the treatment chemistry, the plant displayed deficiencies in sludge densification and handling."

Jan 1, 1980

By Robert D. Brown

"Important tax changes, many of them of direct interest to the mining industry, were contained in the budgets brought down by federal and provincial finance ministers across Canada this spring. This month, Tax Notes presents a brief summary of important tax changes introduced at the federal and provincial levels in the last few months.IntroductionIn the March 1980 issue of the CIM Bulletin, Tax Notes surmised that the short-lived 1979 budget proposals of the former Conservative government offered a unique glimpse of budgetary changes that might be unfolded in 1980. Scene II of this ""now you see it-now you don't"" drama opened on April 21, 1980, when Finance Minister Allen MacEachen, in an ""economic statement""' reintroduced a selection of tax proposals taken from the ill-fated Conservative' budget of December 11, 1979, but refused to bring forward major new proposals in tax and finance.Mr. MacEachen proposed a 5% surtax on federal corporation income tax to apply in the 2 years from January 1, 1980 to December 31, 1981, as a slightly modified version of the same surtax proposed by former Finance Minister Crosbie in his December budget address. Mr. MacEachen also reintroduced a number of technical amendments which would affect the taxation of mining income in certain instances. In addition, a large number of other tax proposals suggested in the previous Conservative budget were also reintroduced, although there are some notable omissions."

Jan 1, 1980

By Premil Agarwal, Alok R. Patnaik, Pulak Dhar, Prakash C. Patnaik

In this study, a physics based model has been presented, considering the growth of the thermally grown oxide (TGO) layer on the bond coating of a thermal barrier coating. Using diffusion equations, a model has been developed to physically describe the oxidation process. The mathematical equations representing the diffusion formulations have been solved numerically. The computed results show the depletion of Al in the bond coating as it diffuses both towards the super-alloy substrate and towards the TGO produced in between the bond coating and the ceramic TBC top layer.

Jan 1, 2004

"This document sets out the Exchange’s expectations and requirements for a valuation of mineral properties and outlines: the general purpose of valuation reports; guidelines respecting circumstances where the Exchange will require a valuation report; and valuation standards, guidelines and methods that are generally acceptable to the Exchange, 1. IntroductionThis Appendix sets out the Exchange's expectations and requirements for a valuation of mineral properties and outlines:(a) the general purpose of valuation reports;(b) guidelines respecting circumstances where the Exchange will require a valuation report; and(c) valuation standards, guidelines and methods that are generally acceptable to the Exchange.Mining industry standards and guidelines for valuations and valuation reports can be found in the Canadian Institute of Mining, Metallurgy and Petroleum Standards and Guidelines for Valuation of Mineral Properties (""CIMVal"") published in February, 2003 (www.cim.org). CIMVal consists of two parts, Standards and Guidelines. The Standards are mandatory and must be followed in order for a valuation to be CIMVal compliant. The Guidelines in CIMVal are not mandatory, but are strongly recommended.The Exchange requires that CIMVal Standards be used by Issuers and their professional advisors when preparing valuations and valuation reports on mineral properties. The CIMVal Guidelines should be followed by Issuers and their professional advisors in preparing valuation reports on mineral properties, with the exception that the valuation methods and guidelines under Section 4 Acceptable Valuation Methods and Guidelines below, must be followed."

Jan 1, 2003

By A. Morales

Flue dusts from a copper smelting furnace (continuous furnace), have been extensively characterized. The main phases detected have been cuprospinel, anhydrous copper sulfate (chalcocyanite), lead sulfate (anglesite) and arsenic oxides (claudetite and arsenolite). As minor phases, zinc sulfate (zincosite) and several copper or copper/iron sulfides were detected (digenite, anilite, bornite, cubanite), and also a copper oxide (tenorite). The suspension of this material in water leads to the partial dissolution of copper and zinc (chalcocyanite and zincosite) and arsenic oxides. The hydrocyclone classification of the residue makes it possible to obtain two fractions: a copper-rich coarse fraction and an arsenic-rich fine fraction. The coarse fraction can be recycled to the smelting furnace and the fine fraction can be mixed with wastewater sludge from a paper factory, to make both residues inert before disposing them to landfill.

Jan 1, 2007

By T. Watanabe, M. Nakagawa, K. Kimapong

Lap joint of A5083 aluminum alloy and SS400 steel was produced by Friction Stir Welding (FSW) Process. The effect of welding parameters such as rotational speed, traverse speed and tool dimensions on the mechanical properties and the interface microstructures of the joints were investigated. FSW process could successfully produce the lap joint between A5083 aluminum alloy and SS400 steel. The variations of rotational speed, traverse speed and pin depth of a rotating tool gave rise to various characteristic interfaces of the lap joint and had conspicous influences on the joint properties. The increase in hard and brittle intermetallic phase and defects formed at the interface of the joint decreased the mechanical properties such as the shear load of the joint.

Jan 1, 2004

By Robert G. Boutilier

Mining companies in communities without other large employers often encounter dependent or defiant stakeholder attitudes, sometimes simultaneously. Less often they also see some slip into social dissipation or advance towards sustainable development. This paper presents a four-quadrant framework that shows how patterns of social capital foster these four reactions. The two dimensions defining the quadrants are the social capital levels (a) between the company and each stakeholder, and (b) among stakeholders themselves. Examples from the Antamina mine in Peru illustrate a social capital measurement system that can predict these reactions and help the community chart its path towards sustainable development.

May 1, 2006

By W. M. Silva, Bittencourt. L. R. M.

Three newly developed alumino-silicate refractory bricks for use in safety lining of aluminum electrolysis cells were compared to one commonly used bricks for the same application. It was shown that the increase in silica content and decrease in permeability led to a sensitive decrease in cryolite attack. Both parameters are of utmost importance in selecting bricks for these cells. The reasons for this observation were the formation of a more viscous liquid after the reaction between molten cryolite and the brick, and the reduction of the rate of penetration. Moreover, a novel mortar with high silica content was tested and has shown improved resistance to molten cryolite. The use of oxidizing atmosphere led to increased attack rate in the brick when compared to reducing condition. The opposite effect was observed in the mortars.

Jan 1, 2004

By K. Fukuda

The volatilization behavior of heavy metal in electric ash melting furnaces has a strong relation with its distribution between molten salt and slag. In this study, the distribution ratios of heavy metals between molten salt and slag phases were measured using a hermetic cell. The experimental results showed a relatively rapid loss of Pb and Zn from the salt in the first few hours followed by slow heavy metal vaporization with an almost fixed metal distribution between molten salt and slag. The distribution ratios of Pb and Zn decreased with increasing slag basicity. The mechanism of this effect can be explained by the chlorinated reaction of PbO and ZnO by CaC12.

Jan 1, 2004

By J. Borlee, F. Sorrentino, A. Fleischanderl, M. Gimenez, W. Gebert, U. Gennari

Large quantities of solid by-products are generated by the steel industry and other important activity sectors in Europe (power plants, car dismantling companies, urban incinerators) with no or very limited potential for direct recovery. In the frame of a multi¬national project supported by the European Union, a consortium has been created to develop a treatment process able to turn these by-products into valuable metallic and mineral products. VAI has been responsible for the design, erection and start-up of the pilot plant for the new metallurgical process and for the execution of the test campaigns, with the targets defined together with the partners. Up to now, 9 campaigns comprising 60 heats have been performed successfully. By-products from C-Steel and stainless steel plants, as well as fly ash and auto shredder residues, have been used and defined products such as hydraulic binders for cement, metallurgical powders for De-S practice and recycled metal phase have been produced. The mineral products were positively assessed under industrial conditions. Results from cement tests and secondary metallurgy are reported, as well as a detailed characterization. The economic value of the products, credits from avoiding dumping and significant savings on CO2 emissions make the new process economically very attractive.

Jan 1, 2004

By George Hope, Dave Green, Jacques McMullen

The Est Malartic mill has been treating massive sulphide, copper/gold ore from the Bousquet 2 mine since 1989. The need to minimize copper content in flotation tails which are leached for gold recovery and to produce a saleable copper concentrate led to the evaluation of Conventional, Column and HG flotation methods. The HG method was preferred and two full-scale cells were installed and operated over a two-year span. In 1992, it was decided to expand the mill capacity from 1500 tpd to 2500 tpd. A total of nine additional HG Tank Cells were installed to provide additional roughing and cleaning capacity. The expanded plant has been operating since June 1993.

Jan 1, 1994

By X. Xe, B. Myhre, N. Zhou, B. Sandberg, Z. Chen

Effects of microsilica and reactive alumina type on flowability, flow decay and working time of Al2O3-SiC-C castables for blast furnace trough were investigated. The results show that at a targeted self flow values of (80 ± 10)%, water demand markedly decreases with increased microsilica addition. The nature of reactive alumina has a strong influence on flowability of the castables. Higher microsilica content contributes to a longer working time. The flow decays gradually until the working time and then drops abruptly. In addition, microsilica have positive effect on both cold strength and hot strength.

Jan 1, 2004

By B. T. Lu, J. L. Luo, H. X. Guo

This paper investigated the synergistic effect in the slurry-erosion process of carbon steel. In line with the mechanisms of material loss, the synergism due to interaction of erosion and corrosion was divided into the corrosion enhanced by erosion and erosion enhanced by corrosion. The erosion-corrosion tests were conducted with A1045 steel in slurries containing silica sand. Experimental results showed that the rotating of the sample in corrosive media raised both OCP and corrosion rate, but the impingement of solid particles did not affect the corrosion current significantly. In the quiescent solutions, the Faraday's law gave a good prediction for the weight loss caused by corrosion but for rotating samples, the weight loss experimentally measured was virtually greater than that predicted by the Faraday's law, indicating that the corrosion-enhanced erosion could occur in corrosive fluids in absence of solid particles. A half-logarithm relationship was observed between the weight loss due to corrosion-enhanced erosion and the anodic current density.

Jan 1, 2004

By V. C. Pandolfelli, P. Bonadia, F. A. O. Valenzuela, L. R. Bittencourt

Refractories for aluminum cells, if not properly selected, can lead to increased energy consumption and even shorten the pot life. Based on recent advances in understanding the deterioration mechanism of cathode materials, several commercial bricks in the SiO2-Al2O3 system were compared to the one used by an Alcoa smelter. Both physical and chemical properties were considered in the selection of the refractories. A more reliable method of permeability measurement, which takes into account inertial and viscous effects during the fluid flow, was applied. Additionally, the traditional cup test and other characterization techniques, such as thermal conductivity, X-ray diffraction, and mercury porosimetry, indicated that a brick with a relatively low alumina/silica ratio, presenting low open porosity and low permeability, far exceeded the performance of the brick currently in use.

Jan 1, 2004

By R. W. McConnell, R. P. Racher

High quality steel production requires extended treatment of the steel in the steel ladle. This has a remarkable impact on the steel ladle refractories, e.g. the need for high performance functional refractories like purging plugs. Operational changes such as increasing tapping temperatures, longer hold times and more aggressive secondary metallurgy are countered by the need for thinner refractory linings and longer refractories life. These combined factors have led to a resurgence in interest in magnesium aluminate spinel raw materials. Magnesium aluminate spinels have been used in steel-making refractories for many years, in a variety of different forms. This paper reviews the production, properties and performance of spinels. Recent developments in the applications of spinels will also be discussed.

Jan 1, 2004

By Kousuke Takahata, Hirofumi Yoshimura, Jun Nakahigashi

Studies of a protium treatment for grain refinement of a + ß type titanium alloy are reviewed and recent experimental results are introduced. Protium treatment consists of the following three processes: (1) protium absorption, (2) martensitic transformation and hot working, and (3) final treatment for protium desorption and recrystallization. A combination of these processes results in the ultra-fine grains of 0.3 to 0.5 µm in diameter with high angle boundaries. The ultra-fine-grained material exhibits superplastic elongation of over 9000%. Superplastic forming was successfully used to fabricate a denture base. These materials may be widely applicable as biomaterials in various medical industries.

Jan 1, 2004

By V. Ramachandran

The successful advent of solvent extraction (SX) reagents for copper recovery and improvements in electrowinning of copper to produce LME grade A copper cathode have paved the way for the hydrometallurgical treatment of copper oxide and low grade sulfide ores. This has resulted in about 25-30% of the world's copper being produced today by the Leach-SX-EW process. The obvious next step was to develop processes for the hydrometallurgical treatment of copper sulfide concentrates, as an alternative to a typical smelter-refinery complex. The current paper updates the processes that have been developed to date with emphasis on processes that are being commercialized or that are seriously under consideration for commercialization. Most of the discussions relate to the hydrometallurgy of chalcopyrite concentrates, which account for about 70% of the world's known copper reserves. In summary, in the last thirty years, the hydrometallurgical treatment of copper sulfide concentrates has attained full maturity and will be a serious option to contend with while evaluating any future new copper plant.

Jan 1, 2007

By M. Jahazi, M. Brochu

This paper describes the advantages/disadvantages of electron beam freeforming using two different types of filler metal: (1) brazing paste and (2) solid wire. Sound buildups were obtained from both filler metal. The freeforms produced with the brazing paste showed a certain level of porosity, which was reduced by successive melting. In comparison, the solid wire buildup was practically free of pore. When compared with the solid wire filler, the brazing paste produced narrower buildups but a larger scattering of the width.

Jan 1, 2004

What Discounted Cash Flow Analysis can do for you: ?Provide an accurate financial analysis of a project for the first 25 to 30 years of operations ?Identify cash flow requirements ?Identify relative sensitivity of the project to the various input parameters ?Place a value on the resource in place after 30 years of operations ?Correct for errors in input parameters

May 1, 2010