Search Documents

By A. L. Williamson

Bio-mining is a cost-effective, energy efficient and potentially environmentally protective method of exploiting a variety of ore deposits, from high-grade base metal deposits of nickel to lower-grade uranium and rare earth deposits such as are found in the uraniferous quartz-pebble conglomerate beds of the Quirke Syncline, Elliot Lake, Ontario. The effectiveness of bio-mining in Elliot Lake depends on the success of bacterially-influenced dissolution of metals of economic importance. The determination of both the dissolution efficiency and rate controls for uranium and rare earth elements from bio-extraction processes is critical to assess the potential for success of bio-mining along the Quirke Syncline. This poster provides an overview of proton-mediated biogeochemical dissolution of more than 50 elements, including uranium and rare earth elements from samples of the low grade uraniferous ore collected as drill core from the Elliot Lake area. The elemental data is quantified using advanced spectroscopic tools (ICP-MS and ICP-AES) to analyze solutions obtained from a series of environmentally controlled biologically-mediated uranium ore extraction experiments. The findings are being to guide design of larger scale bio-leaching experiments to further assess the potential for success of bio-mining along the Quirke Syncline.

Aug 1, 2010

By Richard Dawson

Increasing global demand for coking coal has initiated several new coal mine developments in northeast BC. These developments are able to take advantage of the currently under utilized infrastructure that was put in place during the 1970?s and 1980?s for the Quintette and Bullmoose coal mines; which includes the Town of Tumbler Ridge, a 1,000km rail line to the coal terminal at Prince Rupert and a road system providing highway access to the town site. Coal within the two foothills regions of BC (north-east and south-east) is mined by open pit truck/shovel methods. Optimized mine plans require a thorough understanding of Rocky Mountain structural geology, attention for access in steep terrain, and a related understanding of the geotechnical conditions that control the stability of pit slopes and waste dumps. Thus there is a requirement to properly integrate mine planning with geotechnical engineering considerations. Many of the technical issues are well understood from experience during the past 30 years of Western Canadian coal mining. The challenge is to ensure that the mine plans are able to take full advantage of these lessons learned. The paper will focus on mine planning and geotechnical design issues to do with high angle-of-repose waste dumps and steeply bedded footwall slopes to illustrate the advantage of properly recognizing the important stability control issues during the early stages of engineering evaluations. Case histories from the existing and planned coal mining operations will be presented.

May 1, 2006

By Rodney S. Read

This paper outlines a reasoned argument why no large-scale fracturing or faulting will be induced in the host rock by a deep geological repository (DGR) for nuclear fuel waste. Four DGR designs in three possible host rocks, including crystalline and sedimentary rock types, are considered. The reasoned argument draws from results of previously conducted thermal- mechanical analyses and new scoping calculations, along with evidence from experiments conducted in Canada and elsewhere. It is concluded that large-scale fracturing in the far-field is implausible given the expected in situ stress conditions in relation to rock strength. Near-field damage development and fracturing are expected in DGR scenarios in the different rock types, but these near-field effects are not expected to lead to large-scale fracturing that could compromise the integrity of the DGR and surrounding rock mass. Additional analysis and characterization activities are recommended to further validate the reasoned argument. Thermo-poroelastic loading of the rock mass is identified as one possible driving mechanism that should be studied further.

May 1, 2009

By T. Cutard, E. Yeugo Fogaing, C. Gault, H. Marzagui, N. Prompt, M. Huger, C. Deteuf

This paper deals with studies made in the field of the French research network PROMETHEREF. Several refractory castables are considered in this program. In the present paper, one of these materials is considered, it is a low cement castable based on andalusite aggregates. A particular attention is paid to microstructural changes during the first heating and on their effects on the high temperature mechanical behavior. Microstructural evolutions have been characterized by the way of dilatometry, scanning electron microcopy and X-ray diffraction. In-situ observations by environmental scanning electron microscopy gave complementary results on these high temperature microstructural changes. They deal with microcrack formation, phase changes, crystallization, liquid phase formation and sintering. By propagation of ultrasonic waves, high temperature continuous measurements of the Young's modulus have been made. Results confirm the existence of microstructural changes and allow to quantify the Young's modulus variations all along specific thermal cycles. High temperature four point bending tests and room temperature tensile tests were made in the same temperature range. Behavior evolutions could be found and interpreted with the help of previously mentioned results.

Jan 1, 2004

By J. Larose, E. Irissou

The aerospace business has always been driven by innovation. A significant portion of the overall business technology development strategies is still based today on improved materials and coatings. In this highly regulatory business environment, large amounts of funding are required to increase the maturity level of novel technologies, but the evolution process still remains a delicate endeavor. The technical risks involved during technology development obviously need to be managed and mitigated throughout the development cycle, but other hurdles almost inevitably get encountered, such as budget limitations, transition from lab scale to production scale, loss of focus, intellectual property negotiations and supply chain integrity. This presentation will cover some of the issues raised when a great idea is slowly morphed into an aerospace production part.

Jan 1, 2010

By G. T. Fisher

A continuous process is used at Phelps Dodge Sierrita Inc. to produce copper sulfate pentahydrate via a solution extraction ? crystallization approach to supply the animal feed market. A review of the fundamental concepts of the process and unit operations is presented. Improvements in the process are aimed at achieving a controlled size distribution of product crystals (-40+80 mesh) with minimization of fines by primary nucleation and crystal breakage. An independent temperature control design was implemented for the heat transfer medium (water) in each crystallizer, albeit using common headers in and out of the chiller. This design was developed to maintain a controlled degree of supersaturation in each vessel while preventing localized spontaneous nucleation of fines and reducing encrustation of the heat transfer surfaces in each crystallizer. A model was developed to calculate the heat load and heat transfer coefficient of each crystallizer along with the saturation copper tenor as a function of temperature and free acid.

Jan 1, 2007

By S. Burling

Australia has a number of uranium deposits, but they vary significantly in their mineralogy, grade and textural characteristics. Therefore, information from traditional (or conventional) sources regarding the fundamentals of leaching the uranium and gangue minerals is not always applicable when studying particular ores. Empirical studies on particular ores can be effective in understanding leach systems and can lead to improvements in process design, but there remains a lack of fundamental understanding which is necessary for ongoing process optimisation as ore bodies continue to vary. ANSTO Minerals has undertaken a program of work to address some of the fundamental questions of uranium leaching, including the unexpected impact for some ore types of leaching at high oxidation potential.

Aug 1, 2010

By Mauro Chiesa

An Overview on the Presentation A.The Markets ?Mining Industry ?Capital Markets ?A Six-Cell Matrix of Strategic Options B.De-Risking The Mining Assets ?The Value-Added ?The Assets: Current and in Development ?The Feasibility Study C.(Questions, and answers) Post-Crunch: Some Maxims ?Three Metal Market Models No Longer Prevail ?New models are uncharted: ?be prepared?(ref: Lord B-Powell). ?Capital markets are pricey & uncertain: be your own financier first ?focus on value and on cash-flow (not oz, lbs, tonnes, LOMs, etc) ?Know your banker/financier(and it should know mining) ?In the past, it was ?know your borrower? ?It?s a buyer?s market that wants the ?right deal?: so cast a big net: ?Data must be current, concise and consistent ?3rdparty validation of feasibility work is now a ?passport? ?The risk matrix, with de-risking, is as important as the ?math?

May 1, 2011

By D. Magoon

The metals industry has enjoyed a resurgence in prices and demand for its commodities during the global surge in economic activity that began in 2005. This success has brought with it an unprecedented demand for professionals in all sectors of our economy. Nowhere is that more true than in the mining and metallurgy sectors. However, this welcome improvement follows on the heels of almost two decades of challenging markets for the mining and metallurgy. Our sector's protracted economic slump created a paucity of demand for professionals that had several consequences. Our industry came to be viewed as a low ?tech, uninteresting place to work. Low demand for professionals encouraged students to seek other career options. Reduced demand for graduates, coupled with diminished program funding by our sector, resulted in dramatic shrinkage in university mining and metallurgy programs. This paper explores the lessons to be learned from our recent economic history and discusses some strategies for addressing our image issue. Attracting and retaining good employees is also strongly influenced by a company's reputation and record as a good employer. This reality is very well illustrated by the findings of an international survey undertaken by Towers Perrin in 2005 of 86,000 employees of mid-sized and large companies in 16 countries. The key findings related to attracting and retaining employees are presented. These findings are also discussed in the context of their specific applicability to the mining and metallurgy industry.

Jan 1, 2007

By Jayesh B. Patel, Zhongyun Fan, Hu-Tian Li

"Melt conditioned direct-chill (MC-DC) casting is a novel technology which combines vertical direct-chill (DC) casting with a high shear device directly immersed in the sump for in situ microstructural control. In this paper, the solidification mechanism of DC casting under varying conditions is discussed. The temperature profiles in the sump were measured under the steady state casting conditions by using sacrificing thermocouples. Detailed comparisons of the derived thermal condition are made. The individual role of grain refiner additions, natural thermosolutal convection and forced convection in the sump and the interplay of these factors in determining the solidification structures of DC cast billets are discussed. The MC-DC casting technology can be used to control microstructural constituents and casting defects in DC cast billets/ingots by in situ manipulating of the thermal and fluid flow conditions.INTRODUCTION Direct-chill (DC) casting of aluminium, has been the essential commercial process for producing feedstock suitable for subsequent processing, such as extrusion, rolling or forging. Fine and equiaxed grain structures in the as-cast billets/ingots are required to enable a fine and uniform distribution of second phase particles and microporosity. This leads to higher productivity, more cost-effective homogenisation and more efficient downstream thermomechanical processing. The addition of chemical inoculants has been the standard industrial operation prior to casting for grain refinement of Al alloys. However, it has been established that less than 1% of the grain refiner particles added actually act as heterogeneous nuclei to refine the grain structures, showing a very low grain refining efficiency (Greer, Bunn, Tronche, Evans, & Bristow, 2000). Moreover, the remaining particles from the grain refiner addition in the final casting may cause surface defects during downstream processing. A major issue of the metallurgical quality of large sized ingots/billets is the non-uniformity of microstructures even with chemical grain refiner additions. This is due to the fact that the grain structure formed in the different zones of the billet depends on the local chemical composition and local cooling rate. The local cooling rate can vary from 0.4~1 K/s at the centre of the billet to around 10–20 K/s at its surface zone (Nadella, Eskin, Du, & Katgerman, 2008). The large thermal gradient along radial direction between billet surface and interior of the melt during conventional DC casting induces thermal stress and cold cracking even with grain refiner addition. Therefore the control of casting defects, such as macrosegregation, porosity, cold/hot cracking and distortion of the billets/slabs, etc., is still challenging in industry, causing high scrap rate of DC cast ingots/billets even with grain refiner addition."

Jan 1, 2018

By E. P. Cadwell

"Throughout the years Cyanamid has been a supplier of cyanide and a supplier of information to the mining industry. In general, the knowledge of mineralogy is greatly overlooked. Mineral deposits in the Western hemisphere have been exceedingly rich in the past but now they are becoming poorer. In other words, we will have to use our talents to the utmost to extract the precious metals and base metals from these ores. Modifications of some of the mineralogical equipment displayed here belong in the mill.Cyanidation of copper has been one of the main projects in our labs in recent years. De-rimming or de-filming of copper in order to upgrade copper concentrate was the main aspect investigated. A study was made as to how wide spread was the filming of secondary copper on pyrite, and to what extent it affected the copper industry. It was very wide.Often there is no conception as to what the minerals are. One open pit copper producer with a chalcopyrite ore was producing a copper concentrate with a 5% copper value whereas chalcopyrite contains 35% copper. They used primary and secondary grinding and a regrinding section. The ore contained about 8 parts chalcopyrite to one part of other copper minerals. In tests, a 3 1/ 2% copper rougher concentrate, cleaned without regrinding but conditioned with cyanide for a low contact time of 30 seconds produced a 30% copper concentrate with 90% recovery by removal of the film. It was of utmost importance that some quantitative mineralogical analysis be made before flow sheet changes were made. Every man should be trained to do his own microscopic examination in order to get quick answers. The fundamental thing in all mineral dressing is to first of all know the minerals and the mineral associations."

Jan 1, 1964

By R. Pelletier, Herny. E., C. Allaire

Corrosion of refractory linings by molten metals is controlled by interactions between penetration and chemical reaction. Corrosion of aluminosilicates by molten aluminium is no exception. The early stage of corrosion can be described as a particular case of reactive wetting over a porous medium. Although the reactivity between aluminium and silica is great, which should improve wetting and penetration, the presence of air and the formation of a protective oxide layer disfavours initial penetration. This paper presents the results of an exploratory study on the effect of some parameters on the initial stage of aluminium penetration. Penetration kinetics and metal intrusion tests have been performed on alumina and silica powders with pure aluminium and Al¬5%Mg. Capillary models are used as tools of interpretation. Penetration kinetics tests had a poor reproducibility and the kinetics itself can not be explained very well by the capillary-tube-bundle model. On the other hand, a capillary model initially developed for ice intrusion into freezing soils produced predictions in reasonably good agreement with intrusion pressure measurements. The effect of particle size and alloy composition can be predicted using this model. However, the effects of temperature and powder chemistry need additional interpretations to be rationalised. An unusual resistance to penetration of silica powder by molten aluminium have been observed in a series of experiments. This led the authors to the strange conclusion that oxygen should be seen as an excellent non-wetting agent and that there might be ways to use it in industrial applications.

Jan 1, 2004

By W. E. Johnston

At last year's Annual Meeting a paper by Haultain and Johnston was presented entitled Is the Gold in Tellttrides Soluble in Cyanide? Since then the writer has continued the study of various phases of this problem. Samples and specimens of ore from some of the Kirkland Lake mines have been studied and non gold-bearing tellurides have been found in these that are not soluble in ordinary mill solutions. Samples of tailings, both old and recent, from this district have been examined with apparatus and methods that have proved very successful in detecting the presence of extremely minute quantities of tellurides. Tellurides, both base-metal and gold-bearing, have been discovered in these tailings, but only in such minute quantities that their presence would not affect the ordinary assay results. More free gold particles have been found in the tailings than gold-bearing tellurides. Much experimental work has been done on tellurides, concentrated from high-grade material and from ordinary run-of-mine ore. The gold-bearing tellurides behave very much as does gold itself. Finely divided particles are dissolved fairly rapidly, coarser particles more slowly. All the tellurides are soft and brittle and also have a high specific gravity, with the result that they are extremely finely divided in ordinary mill practice. The ordinary high-lime solution of Kirkland Lake practice is suitable for the dissolving of the gold tellurides. Oxygen is necessary, but apparently not more so than in dissolving gold. Some particles have been found that appear under the microscope to be ordinary metallic gold particles, but on heating they show a small telluride content. These appear to dissolve more slowly than gold. There is considerable variation in the ratio of tellurides to gold from different points in the mines. So far the writer has failed to find any connection between this ratio and the richness of the ore. Generally speaking, the base-metal tellurides predominate. Some of these contain gold but this may be due to a mixture of tellurides in the one particle.

Jan 1, 1933

"At the May 15, 2006 and the May 1, 2007 Canadian Securities Administrators (CSA) Canadian Institute of Mining, Metallurgy and Petroleum (CIM) meetings in Vancouver and Montreal, CSA requested CIM consider certain issues arising out of the CSA review of Technical Reports and public disclosure, in general, regarding the practice of estimation and reporting of Mineral Resources and Mineral Reserves. The following is a summary of the issues raised by the CSA and the responses of the CIM.Preamble: At the May 15, 2006 and the May 1, 2007 Canadian Securities Administrators (CSA)-Canadian Institute of Mining, Metallurgy and Petroleum (CIM) meetings in Vancouver and Montreal, CSA requested CIM consider certain issues arising out of the CSA review of Technical Reports and public disclosure, in general, regarding the practice of estimation and reporting of Mineral Resources and Mineral Reserves. The following is a summary of the issues raised by the CSA and the responses of the CIM Reserve Definition and the CIM Estimation Best Practices Committees (the Committees). This information is intended to provide the Qualified Person (QP) with further guidance when estimating Mineral Resources and Mineral Reserves and in preparing a technical report written under National Instrument 43-101 (NI 43-101). Several members of the CIM Reserve Definition Committee, the CIM Estimation Best Practices Committee and some members of the Committee for Mineral Resources International Reporting Standards have reviewed these issues and provide the following commentary.Issue 1. - CSA requested CIM review and comment on the selection of an appropriate commodity price to be used in Mineral Resources and Mineral Reserves estimates.Commodity prices are used in the estimation of Mineral Resources and Mineral Reserves and in the economic analysis of a property. In times of rapidly changing commodity prices, or when prices are at the extreme ends of a commodity price cycle, the QP has a difficult job in selecting an appropriate commodity price.• The selection of appropriate technical variables, including commodity price, is clearly the responsibility of the Qualified Person (QP). The QP must describe the reasons for selecting these variables, including price, in the technical report.• The definition of a ""Mineral Resource"" contains the wording ""reasonable prospects for economic extraction,"" therefore, a QP must select economic parameters, including commodity price, that will result in an estimate of Mineral Resources and Mineral Reserves that have ""reasonable prospects for economic extraction""."

Jan 1, 2003

By M. L. Free

Laboratory scale extraction of metals from heterogeneous materials such as copper ores is often performed using fine material to increase kinetics and reduce sample size requirements and costs. In contrast, commercial extraction is usually accomplished using much larger material sizes than are used in laboratory settings. The large size difference between laboratory testing and commercial application materials makes it difficult to use laboratory test data to accurately predict performance for commercial material. One solution adopted widely in industry is the use of large test columns. Large test columns cost considerably more to set up and run and take much longer periods of time to evaluate than laboratory scale tests with small particles. Consequently, from a cost and data collection efficiency perspective, the development of accurate scale up methods offers significant potential for saving both time and money. This paper provides details for a new approach to correct for scale-up phenomena in heterogeneous material processing.

Jan 1, 2007

By Lawrence Devon Smith, Keith Spence, William Roscoe

"In March 2003 the CIM Council adopted and approved the document “Standards and Guidelines for Valuation of Mineral Properties” as developed by the Special Committee of the Canadian Institute of Mining, Metallurgy and Petroleum on Valuation of Mineral Properties (CIMVal). The document is referred to as the CIMVal Standards and Guidelines. The document evolved from a specific recommendation by The Mining Standards Task Force (MSTF) of the Toronto Stock Exchange and the Ontario Securities Commission in its Final Report (January 1999) that the CIM form a committee of valuation practitioners to review and advise on approaches to valuation of Mineral Properties. The CIMVal Standards and Guidelines are organized into two parts: •,Standards which are general rules in the Valuation of Mineral Properties. The use of the Standards is mandatory if the Valuation Report is stated to follow CIMVal (although not mandatory in the sense of having regulatory authority). Definitions are given at the beginning of the Standards. •,Guidelines which elaborate on the Standards and, while not mandatory, provide guidance and best practices which are highly recommended to be followed in the Valuation of Mineral Properties.CIMVal specifies requirements for the Qualified Valuator who has the responsibility for choosing the appropriate approaches and methods for the valuation of mineral properties. With regard to the specifics of the application and practice of valuation approaches and methods, CIMVal directs the Qualified Valuator to the large body of published papers, published valuations, presentations and court judgments to guide his or her choice. This is also the approach taken by VALMIN (Australia) and SAMVAL (South Africa). To facilitate the dissemination of industry practice, the CIMVal Committee organized a “Valuation Day” at the CIM Annual General Meeting in Toronto (Mining Millennium 2000), on March 8, 2000. Industry experts presented papers on valuation of Mineral Properties which were subsequently published in a proceedings volume and individually ad technical papers in the CIM Bulletin. The Management and Economics Society of CIM has continued to identify and publish papers on valuation in the CIM Bulletin and Magazine. The present document gathers in one place the CIMVal Standards and Guidelines, the papers from the 2000 Valuation Day, and a number of subsequent papers that illustrate industry practice for the valuation of mineral properties."

Jan 1, 2003

By T. Cutard, H. Marzagui, E. Ouedraogo, M. Roosefid, M. Prompt, C. Deteuf

The present work is achieved in the framework of a French national program on modeling and experimental characterization of the thermo-mechanical properties of refractory materials (PROMETHEREF). This research program is aimed to establish fair models and experimental database and to make it available to industrial partners for numerical simulation of industrial structures made of these materials. The present paper focuses on two silica-alumina refractory castables, an andalusite based one and a bauxite based one. We will present the first rheological characterization results achieved at room on normal and preheated samples of these two refractory castables. Refractory castables are characterized with the help of four points bending tests, compression tests and tensile tests.

Jan 1, 2004

By D. Harris, S. Murugesan, G. Ye, G. Oprea, J. Rigby, T. Troczynski

The spinel-added and in-situ spinel bonded castables have been developed and widely used in steel industry. It is challenging to develop magnesia-based castables for the non-ferrous industry because the temperatures in industrial furnaces are significantly lower than those in the steel industry and therefore the binding systems of these castables must have the capability to develop a ceramic matrix below 1300°C. It is also challenging to develop a good binding system without addition of fume silica, because the hydration of magnesia may take place during installation, curing and firing of the castables. This work presents the experimental results on developing magnesia-based cement-free, silica fume-free refractory castables using hydratable alumina as the hydraulic binder and a spinel phase as the final ceramic binder. In order to activate the sintering and have a ceramic matrix well developed at the relatively low required temperatures, ultrafine aluminas, chromia, magnesium-aluminate spinel and aluminum titanate powders were used as components of the binding system.

Jan 1, 2004

By Ch. Wenzl

Anodes must have a certain physical and chemical quality in order to provide uniform anodic corrosion and meet the requirements of electrorefining, i.e. to achieve a high current efficiency, low energy consumption, low amount of anode scrap and low effort together with high cathode quality. Various properties of the anodes can be influenced directly by the casting process, which is the interface of pyro- and hydrometallurgy of copper. The aims of anode casting ? high output and long mould lifetimes ? are not consistent with good physical anode quality. The physical requirements of an anode are smooth surfaces, uniform weight and thickness, minimal edge effects, minimal distortion of the body and the lugs, as well as a homogeneous microstructure, in order to achieve uniform dissolution behaviour. The chemical quality of the anode copper is a task of electrorefining operations, but the elemental distribution within the anodes, which should be as homogeneous as possible in order to provide uniform anodic corrosion, can be influenced by the casting process.

Jan 1, 2007

By Joachim von Scheele

An oxyfuel-based technology - OXYFINES - has been introduced for in-plant recycling. It provides fines, dust, sludge (without any drying-step) and other by-products arising in the steel and metal producing industries to be recycled directly back into existing processes or a separate unit on-site. Results from full-scale installation (20,000 tpy) for dust treatment, full-scale and pilot-scale trials with dry and wet materials in the steel and ferroalloy industries are presented. Processing rates at 3.5 t/h have been demonstrated. The product is agglomerates or lumpy pieces, the latter if the product has passed an all-liquid stage and thereafter been crushed. The technology does not only provide a solution to the problems connected to dust and sludge generated in metal production. It also turns these materials into a low-cost raw material useful for the production in question, thus replacing part of the raw material input in electric arc furnaces, blast furnaces, etc. Elements harmful to re-use of the processed dust or sludge, e.g., zinc and alkaline components in steel production, are removed as secondary dust, and material yield of main components for re-use is very high, about 98%. The paper reviews the concept, the results obtained and its status; its use for sludge recycling is emphasized.

Jan 1, 2004