Search Documents

By Kari Niiranen, Andreas Boehm

LKAB (Luossavaara-Kiirunavaara AB) is operating underground iron ore mine, with three beneficiation and pelletizing plants in Kiruna, Northern Sweden. The wet low intensity magnetic separation (WLIMS) is regarded as the crucial part of silicate mineral separation from the ore. The Kiirunavaara iron ore deposit shows a rather low content of silica (ca. 2.3 to 3.3 % SiO2) but the silica grade is expected to increase in the deeper parts of the deposit. This can be problematic in the case of DR pellet quality with an average silica grade under 0.75 % SiO2. A laboratory scale methodology was developed for the systematic characterization of the ore for mineral processing with the focus on silicates at the Institute of Mineral Processing, University of Leoben. This methodology is combining mineralogical, geochemical and process mineralogical characteristics. Automated mineralogy (QEMSCAN) was used to study the modal mineralogy, the distribution of silicate minerals in different particle size classes after comminution, the deportment of silicon (Si) between various silicates and degree of liberation and intergrowth of magnetite and silicates. Based on the mineralogical investigations, actinolite, phlogopite and even quartz and albite are the predominating SiO2 bearing minerals in the ore. The important result of the investigations was the discovery of two separate subtypes within the high silica ore type B2 based on their mineralogy and mineral processing characteristics. The crucial part of the investigations of intergrowths and liberation of magnetite results was the magnetic separation tests carried out with the Davis magnetic tube. The binary intergrowths of magnetite and the silicate minerals (mostly actinolite) are the most common type of mineral association discovered. The significant characteristics in the intergrowths of magnetite and actinolite are the fine-grained magnetite inclusions in actinolite which may end up increasing the SiO2 grade in the magnetite concentrate despite magnetic separation.

Jan 1, 2016

By Osvaldo A. Bascur

Industrial complexes rely on measurements of flow rates, qualities, and concentrations for monitoring and optimizing their operation. Corporations use the data from the various sensors and measurements to make business decisions, which affect the profitability of the operation. However, gross errors, due to a variety of reasons like faulty sensors, bad instrument calibration, or incorrect process models may corrupt the actionable information supplied to operations, quality managers, and maintenance personnel. The solution is to use the sophisticated new tools to model the process, sift through the available data to locate the gross errors, and use statistical data reconciliation to validate the sensors and instruments. In this way the data are unified to give the most accurate plant information for use by the monitoring and decision making processes. Most mining and metallurgical plants use predictive maintenance policies based on statistical analysis and special techniques, like vibration analysis, and oil and lube analysis for critical equipment. Process control strategies are installed in several metallurgical sites. All of these depend on reliable and accurate data. The data unification methods validate the individual measurements by using the concept of balances and statistical techniques where each instrument is no longer independent of the other measurements in the facility. This paper refers to the data unification and analysis methods required for profitable plant operations. Continuous improvement and monitoring of the measurement system at the plant and analysis of the reconciled data provide the best information for the decision-making process. On-line gross error detection and elimination methods are required to ensure efficient evaluation of process performance and process optimization. An open discussion of the new methods for gross error detection and data unification will be presented.

May 1, 2001

By Jianhong Xu, Hailong Hou, Yu Jing, Yundong Wang

Microcapsules containing extractants have been applied to the extraction of metal ions, organic acid, pesticide, and herbicide. The difficulties of conventional liquid-liquid extraction in phase mixing and phase separation (e.g. high energy consumption, emulsification phenomenon, and large equipment requiring housing) could be overcome in a liquid-solid system by using microcapsules. Even some extractants with high viscosity and poison can be encapsulated conveniently into microcapsules. In the work described in this paper, polysulfone microcapsules containing 2-ethylhexylphosphonic acid mono-2-ethylhexyl ester (P507) were successfully prepared. Then, the extraction rate of lanthanum, samarium, and erbium in dilute solution into the microcapsules containing P507 was studied. An extraction kinetic model is proposed based on the interfacial reaction model accompanied by intraparticle diffusion expressed by Fick’s law. The extraction efficiency was obtained by using the kinetic model with the separately determined complex formation rate constant and the intraparticle diffusion coefficient. From the results, it was confirmed that the kinetic model could predict the experiment in a microcapsule system over a wide concentration range of lanthanide solution. In the future, the model could provide good guidance for the design and application in extraction of lanthanides.

Jan 1, 2014

By B. Dubreuil, J. -M. Lalancette, D. Lemieux

Arsenical bearing deposits are posing an increasing challenge for the mining industry. In particular, mineral processing of arsenical sulfidic ores for base and precious metals recovery tend to produce problematic arsenical tailings. This arsenic being present as sulphide or oxide, tends to dissolve, contaminating surface and underground waters. To meet the environmental regulations, it is often required to stabilize the arsenic in a more insoluble form. Dundee Sustainable Technologies has developed a new patented technology using vitrification of the arsenic oxide in an economical way, giving a stable solid, well below the environmental regulations upon leaching. This technology involves oxidation of As (III) to As (V), by using a low cost natural oxidizer and transformation of the produced arsenic oxide into calcium arsenate, which is not volatile at the melting temperature of the glass. This technology would be advantageously applied on most cases around the world where sulphide concentrates are oxidized in a fluidized bed or smelted.

Jan 1, 2014

By Carricajo T., S. Nazari

This paper discusses a unique dynamic solution for optimizing comminution area in real time. The proposed technology is a combination of model predictive controller, optimization methods and real-time digital twin for mineral processing. For grinding area, the ultimate goal of an effective control strategy is to maximize the mineral processing, reduce energy consumption and stabilized size classification. To have a continuous and effective comminution operation, a reliable control system that minimizes the need for human intervention is necessary. The implemented advanced control strategy for comminution area consists of two layers in hierarchical structure. The lower layer objective is to stabilize the process stabilization using model based predictive controller (MPC) technique. The unique MPC used in this layer is called BrainWave™ chosen for its robustness, convergence and delay handling; furthermore, the developed platform offers stable and repeatable solution and has short implementation time. The upper layer is a supervisory control, which sends the preferred process operation points to the lower layer to drive the process towards optimal performance. The goal of this layer is to optimize the process targets, as well as making decision. To increase process performance, automatic ore characteristic adaptations are implemented in this layer. A digital twin of comminution area is built in the second layer that runs amongst the process in parallel. By communicating, the process data in real time, a virtual densitometer is built that is being used in our advance process control strategy. Our control strategy has been developed, tested and implemented in various areas of a copper concentration plant. The targets for implementing advance process control are usually increased throughput, decrease energy consumption and variability reduction in particle size distribution. Overall, the results showed in different mine sites are increase throughput between 2 and 5%, specific energy consumption reduction about 15% and process variability reduction up to 60%. In this paper we discuss the results of the recent implementation of this technology on Minera Los Pelambres, Minera Collahuasi and CAP Minería. Their concentrator plants have installed control systems with the most updates optimization features, for SAG mill, ball mills and thickeners.

Jan 1, 2019

By C. -M. Katsari, G. N. Anastassakis

"Copper is considered one of the most important industrial metals because of its properties (conductivity, malleability) and variety of uses. Approximately 70% of the global copper is used for various electrical applications, with a significant part of copper originating from recycling, since copper can be recycled and re-used countless times, without any loss of performance and difference in the quality of recycled copper in comparison to that from ore. Copper recycling significantly contributes to natural resources conservation, waste minimization, energy saving, and overall cost reduction. Approximately, 35% of the globally produced copper originates from recycled copper.The objective of the current work is to investigate the recovery of copper from electric wire scraps using wet shaking table as an alternative to air separation methods that prevail over the wet ones in recycling processes. The tests were carried out using feed of correspondingly high- and low-grade in copper. In the first case, the wire scraps had been subjected to shredding only, prior to tabling separation; in the later, the low-content tailing of prior air separation was used as feed ?n table separation.In regard to testing, the following factors were examined: table tilt, water flow-rate, and reciprocating speed. The results of the tests clearly denote that copper wire separation from plastic polymer is feasible, as in most cases, table separation resulted in heavy products of high purity in copper and high recovery, and tailings of very low copper grade. The results of the current work clearly denote that wet tabling can be applied efficiently for the separation of recycled copper wire from plastic, as an alternative to air separation methods, as well as for the recovery of copper from the low-grade tailings derived from air separation methods."

Jan 1, 2016

By B. Skrotzki, E. Augenstein, C. Rockenhäuser

"The aluminium alloy 2618A is an Al-Cu-Mg alloy with additions of Fe and Ni, which is designed for long-term operation at elevated temperature in transportation and aerospace industries. The alloy degrades due to coarsening and dissolution of GPB zones and coarsening of S-Phase precipitates (Al2CuMg). This work investigates the overageing process at the application relevant temperatures of 190 °C for durations ranging up to 25,000 h. The nm-sized precipitates were selectively imaged along the <001>a direction of the Al matrix using dark-field transmission electron microscopy. The resulting images were then evaluated and allow the statistically relevant determination of radii distributions and the average radius of the precipitates dependent on temperature and heat treatment duration. Ostwald ripening of the S-phase does not describe the ageing process adequately. Instead, the evolution of GPB zones during the initial ageing regime needs to be considered in addition to the coarsening process of the S-phase. DSC measurements were performed to determine the presence of GPB zones in different ageing states. This will allow a quantitative description of the ageing process and a comparison to samples aged under external load.INTRODUCTION Alloy 2618A is an Al-Cu-Mg alloy, which is part of the 2XXX series of aluminium alloys. It is used in aerospace and transportation industry due to its desirable material properties for long term operation at elevated temperatures (Polmear, 2006). Fe and Ni are added to form intermetallic compounds, which retain microstructural stability at elevated temperatures (Bergsma, Li, & Kassner, 1996; Elgallad, Shen, Zhang, & Chen, 2014; Oguocha, Yannacopoulos, & Jin, 1996; Wang & Yi, 2006). The size and distribution of the nm-sized S-phase formed from the supersaturated solid solution (SSSS) during heat treatments mainly controls the strength (Khan, Starink, & Yan, 2008; Liu, Zhang, Ding, Sun, & Chen, 2003; Parel, Wang, & Starink, 2010; Shih, Ho, & Huang, 1996; Wang, Starink, & Gao, 2006). The S-phase has the composition Al2CuMg and is orthorhombic under equilibrium conditions (Heying, Hoffmann, & Pottgen, 2005; Perlitz & Westgren, 1943). Early experiments proposed the following decomposition of the S-phase sequence during heat treatments (Hardy & Heal, 1954; Silcock, 1961):"

Jan 1, 2018

By E. Johansson, T. Siren, K. Kemppainen

"As part of the preparations for the design of an underground repository for radioactive waste at Posiva’s Olkiluoto site on the west coast of Finland, there has been considerable site investigation work. Except the extensive surface based investigations, Posiva started in 2004 the construction of an underground characterisation facility termed the ‘ONKALO’. The ONKALO has now been completely excavated to the anticipated repository depth i.e. -430–450 m. The research conducted in the ONKALO gives further information on the bedrock and groundwater conditions of the final disposal site, as well as on the impact of the construction. The ONKALO provides an excellent opportunity to investigate the rock at tunnel scale, to conduct in-situ testing in rock, to develop excavation and final disposal techniques in realistic conditions. The ONKALO has aided in collecting the data needed, supported by a Preliminary Safety Assessment, for the application of the construction license that was submitted in the end of 2012. The target is to begin disposal operations in 2022. According to current plans, the final disposal would end in 2112 and the repository would be sealed up by 2120. The testing in the ONKALO still continues several years. This paper presents the current characterisation and research activities in the ONKALO. INTRODUCTIONAfter the Finnish Government's favourable policy decision in 2001, Posiva Oy, which is an expert organisation responsible for the final disposal of spent nuclear fuel of the owners in Finland, has focused further investigations at the Olkiluoto site, western Finland (Figure 1) and has started in 2004 the construction of an underground facility termed the ‘ONKALO’. The ONKALO is not a nuclear waste repository, but more than just an underground research laboratory URL – it is an underground rock characterisation facility. The ONKALO has now been completely excavated to the anticipated repository depth i.e. -430–450 m. In addition to facilitating bedrock research, the ONKALO also provides an opportunity to develop excavation techniques and final disposal techniques in realistic conditions. Later, the ONKALO facilities can be put into use when building and using the repository. The construction methods and materials have been selected in order not to jeopardise the long-term safety of the repository site. The findings of the ONKALO and other investigations will provide the knowledge needed for an application, supported by a Preliminary Safety Assessment, to construct a final repository for spent nuclear fuel at the site. Posiva has submitted an application for the construction licence for a disposal facility in the end of 2012. The target is to begin disposal operations in 2022 and the repository would be sealed up by 2120."

Jan 1, 2015

By Y. Kocaefe, D. Bhattacharyay, D. Kocaefe

The carbon anodes used in the electrolytic production of aluminum are made of petroleum coke, recycled anodes and butts, and coal tar pitch. Due to technological advances in the aluminum production technology, aimed at increasing production and decreasing energy consumption and greenhouse gas emissions, better quality anodes are required. Presently, the anode quality is evaluated by visual inspection and the analysis of a small core taken from 1.5-2% of the anodes produced. The visual inspection is susceptible to human error and limited to surface imperfections. The analysis of cores takes time, and therefore, it is difficult to determine the existence of a problem and intervene at the right time. In addition, the core does not represent the whole anode due to the non-homogeneity of anodes. A validated online anode quality control system can highly improve the situation. In this article, an electrical resistivity measurement method developed for this purpose is presented.

Jan 1, 2014

By R. W. Pugh, S. L. Ma

"High carbon rods are typically used as the grinding media in rod mills. Usually an AISI I 090 grade of steel is used which provides the high hardness needed for abrasion resistance and sufficient toughness to prevent rod breakage.Work to improve performance in the past has mainly concentrated on increasing the hardness for improved abrasion resistance. This has been accomplished by adding alloys to the steel which uniformly increase the hardness across the rod section.However uniformly increasing the hardness of the rod produces a more brittle product and at high hardness l1evels can lead to rod breakage problems. Heat treatment processes can be used to selectively increase the surface hardness to high levels while maintaining the core at lower hardness levels to give a product that wears slower without breakage. AltaSteel has developed and mill tested a higher hardness heat treated grinding rodThis paper describes the development of a simple model to predict performance improvement with different hardness profiles and the AltaSteel heat-treated grinding rod process. Mill characteristics of the Endako operation are summarized and predicted performance improvements based on hardmess are compared to the approximate 25% achieved in trials running since July, 1991 at this mill. Early results of other mill trials are also presented.INTRODUCTIONAltaSteel, in Edmonton is a major supplier of grinding media. We have a strong desire to continually increase the quality and performance of our products and thereby improve the efficiency of our customers' processes. In the area of grinding rods, we wanted to produce a product with a significant improvement in wear rate. Second to energy, rod consumption usually represents the next highest cost in processing. This paper presents our development of a heattreated grinding rod that has reduced consumption by about 25% in trials to date."

Jan 1, 1993

By K. Sawada

Along with the expanding demand of copper concentrate in Asian countries, custom-smelters have confronted with difficulties of low TC/RC. Now, Japanese Copper Industry have 2 options; investment in mine development and/or recycling of copper scraps. The strategy of global mining companies is analyzed, and implications for Japanese Copper Industry will be discussed from the viewpoint of sustainability of smelters in Japan.

Jan 1, 2014

By T Salman

The construction and use of the B.E.T. (gas adsorption) apparatus is described. Examples are given for the determination of large and small surface areas using nitrogen and krypton. Introduction A NY study of the milling of ores from crushing to grinding, classification, and concentration and finally dewatering of the products involves solid particles which are either in contact with a gas or a liquid phase. The surface area of the solid and its characteristics constitute important parameters in all mineral dressing operations. The success of any particular operation is dependent on the interaction of the surface of the solid particles with the gas or the liquid phase. Particle size and specific surface (surface area per unit weight) continue to be important parameters in the flotation research associated with the adsorption of collector molecules or ions on mineral particles, as in the early years of mineral dressing research (1). In order to understand the mechanism of the flotation process, it is essential that the surface properties of the adsorbent be known.

Jan 1, 1965

By Cesar A. Urbano Jr., Gretchen T. Lapidus

A series of experiments examined silver extraction from a high-grade sulfide concentrate employing thiourea solution. Thiourea was initially oxidized with hydrogen peroxide (H2O2) to form formamidine disulfide (FADS) and used to extract silver from the as-received concentrate and after various pretreatments. Very low recoveries (~30%) were obtained with the as-received concentrate due to competitive cementation reactions by metallic iron and easily oxidizable copper phases. Over 80% Ag recovery was obtained when the concentrate was pretreated to remove this iron and copper. The results suggest that an oxidative acid pretreatment of this concentrates significantly improves silver recovery upon leaching with thiourea.

Jan 1, 2014

By Tommee Larochelle, Henry Kasaini

"Simulation of rare earth element solvent extraction processes for plant design and optimization is complex, requires extensive bench scale and pilot scale testing, and is traditionally performed using proprietary algorithms. The complexity of simulation is mainly due to traditional simulation software solvent extraction modules not being designed to simulate rare earth separation processes because of the interaction between each element. This paper presents an alternative method for designing and optimizing rare earth element solvent extraction separation processes using METSIM to converge each stage of the battery individually until the full battery reached ultimate convergence. A feed-forward controller is used to control the organic to aqueous flow ratio feeding the solvent extraction modules. This method minimizes the complexity of simulating such processes by using inexpensive batch solvent extraction data, and allowing for rapid theoretical optimization, by varying the process configuration and parameters from a graphic interface instead of the traditional code-based interface of most proprietary models. Comparison of the model predictions to pilot plant data reveals that the method can be used to accurately model rare earth solvent extraction processes, as illustrated by its application in the development of Rare Element Resources innovative process.INTRODUCTIONThe Rare Earth Elements (REEs) consist of 16 metals, specifically the 15 lanthanide elements and yttrium, which is typically found in the same mineral deposits as the lanthanides. Scandium can be associated with the rare earth elements, but is usually only present in trace amounts, and therefore omitted. The term “rare earths” originates from an old term used to designate minerals (earths) and their believed scarcity upon their initial discovery. The rare earths designation is now considered a misnomer because it was demonstrated that the crustal abundance of some rare earth elements, such as cerium, is known to be higher than many common metals, such as copper. However, enriched deposits are fairly uncommon compared to other similarly abundant metals. The REEs are typically divided into groups commonly consisting of light rare earths (LREEs), medium rare earths (MREE), and heavy rare earths (HREEs). Light rare earth elements include lanthanum to neodymium, medium rare earths include samarium to gadolinium and the heavy rare earth elements include terbium to lutetium, and yttrium. The REEs exhibit similar chemical characteristics and are usually extracted from the ore and processed into a mixed rare earth concentrate. The rare earth concentrate requires further processing in order to separate the REEs from each other and produce a series of single element products."

Jan 1, 2016

By Colin Jones

Canadian Clay Products Inc., which mines bentonite in Saskatchewan near Truax and operates a plant at Wilcox, is the sole producer of swelling bentonite, often called western bentonite, in Canada. Seven products produced by the company are used in binders, sealants, water and waste water treatment, plasticizing agents, foundries and absorbents. Reserves are reported at about one million tonnes for the deposit but the area in general contains significant additional reserves.

Jan 1, 2001

By M. Maeda, H. Sasaki

Dissolution characteristics of metals vary significantly when they form alloys with other elements. Because hydrometallurgical processes are essential in separation and refining of non-ferrous metals, it is important to study behaviors of alloys in aqueous solutions. The authors have studied dissolution characteristics of precious metals in acid solutions using electrochemical measurement. When precious metals are alloyed with Zn, its dissolution is promoted by an increase in surface area caused by the preferential dissolution of this metal. The electrochemical study also revealed that precious metals dissolved from some alloys at unusually negative potentials; the underpotential dissolutions are explained by activations of these metals in the dealloying.

Jan 1, 2014

By H. J. Hartjens

"With the trend towards bringing into production ore bodies of lower and lower copper content every possible avenue of approach to achieve maximum copper metal recovery and keep milling costs to a minimum are of increasing importance.Equipment manufacturers have contributed a great deal by designing larger mills, flotation machines, pumps, etc. in lowering capital and operating costs; instrumentation and automation usually as a joint effort of operating staffs and equipment manufacturers have resulted in lower operating costs and improved metallurgy. Likewise manufacturers of chemicals used in mineral beneficiation have directed their research and development at new flotation reagents and treatment schemes to complement the needs for more efficient products, permitting coarser grinds without detriment to recovery, higher flotation rates, higher degrees of selectivity, as well as chemicals to improve settling, clarification and filtration. The various treatment schemes in use and suggested for consideration are:1) The choice of the flotation treatment scheme is largely dictated by the desire to operate a simple circuit, originally consisting of rougher and scavenger flotation, with scavenger concentrate either returning to the head of the rougher circuit or joining the rougher concentrate for cleaning by reflotation, with and without prior regrinding. The cleaner tailing was also recycled to the head of the rougher circuit. In the case of porphyry copper ores, this was originally the standard circuit. Lime is the preferred alkalinity regulator to adjust pH, usually in the range 10-12.To avoid the undesirable effects of circulating loads and gain the advantage of simplified control of the rougher circuit, open circuit cleaning is practiced more and more. In this scheme, cleaner tailing is scavenged to produce a discardable tailing and the scavenger concentrate returned either to the cleaner or the regrind circuit."

Jan 1, 1970

By Isabel F. Barton, Matthew J. Gabriel, Mark D. Barton

Process control, mine-to-mill optimization, and other mining operations depend on having robust, comprehensive mineralogical and chemical characterization. However, current characterization methods rely primarily on analyzing samples from trenches, channels, blast holes, and drill holes and interpolating between them, and are not always sensitive to some minerals (such as clays) that cause major problems for mining and mineral processing. Continuous characterization is possible with techniques such as hyperspectral remote sensing, which measures reflectance or absorption of light in the visible to near infrared (VNIR) and short-wave infrared (SWIR) regions of the electromagnetic spectrum. Absorption and reflectance features are characteristic of different chemical bond types, so each spectrum corresponds to a different mineral or material. In remote sensing, each pixel in the scanned area has both a location and a spectrum. This makes hyperspectral remote sensing potentially useful for characterizing mine site materials. In this study, we tested a hyperspectral remote sensing system as a method of characterizing the mineralogy and material types at mine and metallurgical sites. Our test site was a small open-pit copper mine and leach operation in the southwestern U.S. We scanned mine highwalls, dump piles, leach pads, and nearby rock outcrops with drone- and tripod-mounted VNIR-SWIR spectrometers. We collected ground-truth data through geologic mapping, sampling, and spot analyses with a portable short-wave SWIR instrument. The results show that the hyperspectral remote sensing system that we tested is capable of distinguishing the types and distribution of spectrally active minerals and other materials in diverse mining settings, including showing wet and dry areas of leach pads; clay and carbonate type and distribution on mine highwalls, leach pads, dumps, and rock outcrops; plant type and distribution; fault zones, bedding planes, and other geological features; and qualitative spectral matches between dump piles and areas of the mine highwalls. Hyperspectral sensing proved particularly sensitive to the presence and type of clay and carbonate minerals, which cause geotechnical and metallurgical problems such as highwall failure, gangue acid consumption, and flotation sliming. Examples will be presented and discussed at the conference. Areas of continuing research include automating and streamlining the data reduction process, integrating hyperspectral data with block modeling and mine planning software, and testing the results of hyperspectral sensing in different geological environments.

Jan 1, 2019

By F. W. Crossland

Losses of metal are often traced to incorrect pH/ORP signals in flotation, leaching, extraction, electrolysis, and precipitation processes, aggravated by pressure changes. IC Controls, a Canadian mining sensor manufacturer, developed a new superior pH/ORP sensor that stops metal losses, reduces environmental footprint and contributes to sustainability. The cause of incorrect pH/ORP signal is rooted in the reference. Reference junctions are designed to allow diffusion of reference chloride ions into the process but also allow process ions to diffuse into the reference. This development is important to mines and hydrometallurgists where sulphide, cyanide, ammonia and other poisoning ions are present in the process. These ions react with reference electrolyte components causing the signal to change, drifting from the correct process value. With fluctuating process pressure, ion in migration dilutes the electrolyte producing similar signal drifts. If process ion in-diffusion could be stopped, the pH/ORP signal would be accurate. IC Controls new pH/ORP sensor stops process ion in-diffusion, and remains accurate over long periods. New processes using higher pressure and fluctuating pressurized reactors will greatly benefit from stable pH readings. Similar to IC Controls&apos; proven model 642 Mining pH sensor, our new model 647 contributes to sustainability through reducing disposal costs from waste reagents, lost metal and fewer used sensors.

Jan 1, 2014

Applications of proven real time, through-conveyor elemental analysis technology and benefits achieved will be discussed using case studies in base metals, iron ore and phosphate operations. PGNAA (Prompt Gamma Neutron Activation Analysis) technology and its background in minerals applications and applications which are expected to further improve its utilization will be reviewed. Short payback through operational benefits such as removal of waste from feed, increased feed grade and overall improved productivity will be demonstrated based on results achieved at several processing operations. PGNAA technology is most applicable to conveyed flows as it is unaffected by belt speed, particle size, segregation/layering, mineralogy or dust. As a transmission method able to penetrate in excess of 500mm of rock it provides extremely representative results continuously measuring through the full conveyed cross section and reporting results typically on one to five minute accumulated increments to the control room. Multi-elemental results and moisture content are used for active process control: diverting conveyed flow increments(bulk sorting), blending ore types in plant feed, and providing advance warning of significant quality changes to the downstream plant operators (e.g. flotation). Elements of interest may include deleterious components as well as target metals. Ore feed quality measurements are also useful in metal accounting, ore reconciliation and real time feedback to mining operations. Further benefits can result when combined with other technologies such as particle sorters, to upgrade diverted increments of subeconomic material to achieve higher feed grades and lower deleterious content to the main process. Measurement of elements (e.g. silica) which correlate with ore hardness or grinding characteristics can be used to moderate feed rate to grinding mills to prevent overload, hence optimizing grinding performance and reducing energy and grinding media consumption. Pebble flows can be analysed and uneconomic increments diverted to prevent recirculating flows consuming mill capacity unnecessarily. This also increases average feed grade.

Jan 1, 2016