Search Documents

By F. S. Thurner

This paper, a description of the new ore-unloading and stockpiling facilities at the Sydney Works of DOSCO Steel Limited, deals with a new approach to arrive at the most economical solution to combine ore unloading facilities for common bulk carriers and for different types of self-unloading vessels. Also discussed is the design and installation of a 1-mile-long steel-cord belt conveyor sys-tem with a most modern type of mobile belt conveyor stacker, along with automatic and semi-automatic controls for the entire ship-unloading and stockpiling operations.

Jan 1, 1968

By I. J. Burgess, B. C. Barlow

"The electrodissolution of nickel pellets with different controlled electrical variables was investigated in an effort to mitigate plating residue in Watts bath based electroplating cells. During galvanostatic dissolution at 0.4 A dm-2, the anode potential was seen to oscillate between passive and pitting potentials. In-situ microscopy and ex-situ characterization has shown that lacy-pit formation and large, partially perforated, pit covers form during the potential decay from pitting potentials. In general, covered pitting at low current density shows increased plating residue. Using potential pulses is one way to maintain greater control over surface pitting by creating a higher density of pit nuclei while at the same time controlling their growth. Pits generated from a series potential pulses were examined ex situ for a range of pulse times and stages of pit growth were identified. An alternative method of anode dissolution was devised using potential pulses and duty cycles that allowed average current densities comparable to industrial plating conditions to be achieved. By restricting the time at pitting potentials to 0.05 s, plating residue was reduced more than six-fold in comparison to an equivalent galvanostatic experiment run at a comparable current density.INTRODUCTIONIn typical galvanostatic (direct current) nickel electroplating cells employing soluble anodes, some amount of plating residue is produced which consists of metallic nickel and impurities that detach from the bulk in the form of small fines. Significant buildup of residue requires plating operations be halted and the anode assembly cleaned of residue before operation can resume. While variables in the refining process have been shown to affect plating residue, more precise control of electrochemical variables may provide an attractive route to mitigation of residue."

Jan 1, 2016

By J. Karonen, M. Tiihonen, J. Guentner, L. Haavanlammi, Outotec GmbH, E. Kolehmainen

"Rare earth elements have obtained significant attention during the last few years due to predicted increase in their demand. Several projects worldwide are at pre-feasibility or feasibility stage aiming to commence production. Deposits of rare earth elements are typically complex and multi-metallic of nature. This means that production processes are often also complex and therefore, various metallurgical unit processes are needed. Outotec’s equipment and technology portfolio is very comprehensive and includes hydrometallurgical and pyrometallurgical apparatus and processes applicable to the efficient exploitation of rare earth deposits. Outotec has gained useful experience relevant to the processing of rare earths through several assignments including those for Alkane Resources Ltd. (Dubbo Zirconia Project), Greenland Minerals and Energy Ltd (Kvanefjeld Project), Frontier Rare Earths Limited (Zandkopsdrift project), Tantalus Rare Earths AG (Madagascar), Quest Rare Metals (Strange Lake project) and Orbite Aluminae Inc. (HPA project). The hydrometallurgical test work of two process flowsheets is presented in the paper. A roasting or acid baking step is common to several proposed rare earth projects. In the past, rotary kilns have been used, but Outotec has developed a new process concept to handle the rare earth material in fluid bed reactors. The basis for this development is long experience in fluid bed technology of Outotec in Germany. One advantage of fluid bed roasting is the higher throughput per unit. In combination with the roasting and baking, Outotec offers the gas cleaning and acid plant and provides a complete and closed concept.INTRODUCTIONRecovery of rare earth elements (REE) has obtained significant attention during recent years. It has been estimated that their demand will be boosted because of their need in many technology areas. REE can be utilized in magnets, batteries, displays, catalysts, optical devices etc. (Jordens, Cheng, & Waters, 2013; Zhang & Edwards, 2013). The production of REE is focused in China, which means that production outside of China is very scarce. However, there are multiple active development projects worldwide working towards production of REE containing products outside of China (Chen, 2011)."

Jan 1, 2016

By Greg Johnson

Maintenance needs information about assets to optimize availability and production needs information about performance and consumption to maximize output. In considering both these needs together as, ?Asset Optimization?, the information systems that support them are critical. The theory of Asset Optimization derives from the Lean Manufacturing concepts developed by Toyota, but some changes are required to apply this to mining operations. In particular, mining operations require automated systems due to their geographic spread and they need a strong emphasis on capturing under-performance losses as well as delays and stoppages in production. Leading metal miners and coal miners alike have applied these systems to good effect in the last 10 years. The concepts developed initially in minerals processing plants are now being applied to the mines themsleves as well as the mining logistics chain. Production increases of 5?10% are achievable with the right implementation and consideration of the some key lessons learnt in the last 10 years. Putting these lessons into action is one key step in the goal of optimizing asset performance and thus utilizing the resource at lowest cost.

Aug 1, 2013

By Roger Lacroix

Fuel cell application to mining has been indicated to be potentially beneficial to underground mine worker health and to energy efficiency. In order to define the economic advantages of using hydrogen fuel cell vehicles, a detailed study of operating and capital costs associated with underground loaders and power supply infrastructure has been carried out. The results show that for a typical medium-size mine, operating costs and infrastructure costs are less for the fuel cell option versus diesel. The reverse occurs for capital costs owing to the currently higher cost of fuels cells versus diesel engines. This disparity is expected to decrease given the decline in price associated with fuel cell technology advances. Related market issues for fuel cell manufacturers are also presented. Despite the difference in cost, the resources and mine infrastructure required to operate loaders, and base design of the mine loader, is similar for diesel and fuel call versions.

May 1, 2007

By K. N. Subramanian, H. Kanduth

"It is well known that chalcopyrite can be dissociated into simple sulphides by heating with elemental sulphur at about 475°C:CuFeS2 + S -> CuS + FeS2Experimental work was undertaken to determine whether this ""activation"" could be used to advantage in the selective leaching of copper from chalcopyrite concentrate.A method of treating copper concentrate with molten sulphur was developed and the activated product was leached in dilute sulphuric acid using oxygen, ferric iron or manganese dioxide as the oxidant. The object was to obtain a solution suitable for electrowinning with minimal purification, but it was impossible to obtain rapid extraction of copper without simultaneously dissolving a large proportion of iron. This was attributed to the fact that some of the copper was present as a low iron-copper sulphide (idaite) and that the pyrite formed during the ""activation"" step was more easily oxidized than natural pyrite."

Jan 1, 1973

By Ron Tessier, Claude Bazin, Robert Grant, Mike Cooper

"Grinding simulators are now widely available to assist in the optimization of industrial circuits. They provide circuit operating conditions or flowsheet designs that yield a given product size distribution. However, they do not provide information of the impact of a change of product size distribution on the subsequent flotation or leaching stages. This paper presents a method to predict grade and recovery indices for a flotation plant as a function of the flotation feed size distribution. The application of the method to various size distributions allows the determination of the optimal fineness of grind. A case study for a CuPb rougher circuit of a New Brunswick complex sulphide processing plant is presented to illustrate the method.IntroductionIs the grinding circuit product fineness optimum for the subsequent separation steps? This is a question that is certainly very difficult, but critical, to answer. Laboratory and pilot plant testworks can provide clues as to whether grind should be finer or coarser. For a full scale operation there is no other way than trying to change the setup of the grinding circuit and verify the effect on flotation. True effects can, however, be masked by the numerous and unexpected disturbances inherent to grinding and flotation circuit operations. A good preliminary investigation requires a noise free environment to elaborate possible solutions for the question.Plant simulators provide this noise free environment. However, despite grinding and flotation simulators having evolved significantly for the last 20 years, very little is available on the integration of both simulators to analyze the effect of fineness of grind on metallurgical performances. For instance, a grinding circuit simulator may help to find the tuning of a grinding circuit that will yield the desired fineness of grind, but does not inform on the effect the new product size distribution will have on the separation stages. Linking grinding and flotation would require a flotation plant simulator with the rate and infinite recovery parameters for each mineral in each size interval considered. This approach is seldom used because of the tedious work required to estimate the model parameters. Recently Leroux(1992) proposed a method to predict mineral liberation from grinding ore of known mineralogical texture. Although the method is still at its infancy it may provide, when combined with a reagent conditioning model (e.g Niemi et al., 1982; Bazin et al., 1988), a way to simulate flotation without the need of entering the numerous parameters of a flotation model."

Jan 1, 1994

By E. R. Rivenbark

"The coal handling plant represents an investment of about $100 million in coal handling and storage equipment. The coal receiving is done by a continuous ship unloader that can handle ships in the 60 000 T range at Q rate of 1750 /ph. A unique feature in the system is a stacker/reclaimer unit which will work inside a dome storage structure. The coal for the unit will include any low sulphur coal that can be delivered by sea at an economical price blended with New Brunswick high sulphur coal.ThE flue gas scrubber is a wet limestone system capable of 95% SO2 removal. The scrubber will utilize about 150 000 tonnes of limestone per year and will produce commercial grade gypsum by the forced oxidization method.IntroductionWith the need for new generating capacity being required, New Brunswick Power reviewed, in 1985, its options for the next unit. The study indicated that the most attractive option for New Brunswick Power would be a coal-fired unit capable of receiving imported coal at a sea port. The site selection process resulted in three site options being considered.The existing Coleson Cove and Dalhousie sites, and the Belledune site were considered. To meet load distribution needs, it was then decided that the unit had to be located in the northern section of the province, thus eliminating the Coleson Cove site. The Belledune site was selected because it had the capacity to have additional units added where as the Dalhousie site would have only been able to accommodate one unit"

Jan 1, 1994

By Rodrigo Madariaga, Tracy T. Morris

The practice of stripping copper starter sheets from titanium blanks to be used in a conventional electrolytic tankhouse has been around since the advent of Electrometallurgy. Historically it has been done manually, utilizing many people to produce in some cases thousands of starter sheets per day. Some other conventional tankhouses have successfully converted to using mechanical means to strip starter sheets or have made the switch to permanent cathodes and although robotics have been around for quite some time they have not been used to strip starter sheets until recently. The Amarillo Copper Refinery began using robotics to strip several years ago and the details to how this came about and how the robots work will be described. INTRODUCTION ASARCO LLC (Asarco) was organized in 1899 as the American Smelting and Refining Company. Originally a consolidation of several lead-silver smelting companies, it evolved over the years into an integrated producer of primary non-ferrous metals, including copper, lead and zinc and associated co- products (Marcosson, 1949). Grupo México, S.A.B. de C.V acquired Asarco in 1999. Today, Asarco is a vertically integrated producer of primary refined copper and associated co-products such as gold, silver, molybdenum, selenium and tellurium. Asarco operates three open-pit mines and mills and two solvent extraction-electrowinning (SX-EW) plants all in Arizona plus a copper smelter in Arizona and a copper refinery in Texas. Figure 1 illustrates how the copper metal comes out of the ground at the mine and ends up as a refined product at the refinery The copper refinery in Texas is known as the Amarillo Copper Refinery (ACR) and is located in Amarillo, Texas. It was built in 1975 to replace 3 other aging refineries and was designed to produce 550,000 tons (500,000 MT) of refined copper per year using conventional starter sheet technology. At the time it was commissioned it was the largest tankhouse in the world at just under 1/2 miles long under one roof.

Jan 1, 2019

"In flotation research, relatively little attention has been paid to understanding particle-bubble detachment phenomena compared with attachment processes. With CFD models now incorporating attachment/detachment kinetics, it is important to obtain more accurate formulations for detachment probability. The formula most often used is due to Bloom and Heindel (2002) who proposed that the rate of detachment would equal the product of detachment frequency, as previously estimated by other authors, and probability of destabilization, as estimated previously by Schulze. These two factors both account for the balance between stabilization and destabilization forces, so the product accounts for this effect twice. An integrated procedure has been followed to estimate the overall detachment rate by re-analysing the process. In this analysis, detachment rate is calculated as the frequency of eddy-aggregate interactions (or “collisions”) sufficiently energetic to cause detachment. The Bond number analysis of Schulze has been incorporated into the turbulence frequency analysis of previous authors in an integrated way. The new formulation has essentially the same type of dependencies as the previous model, but gives a lower detachment frequency. Detachment frequency has been calculated using the new formula for conditions relevant to an industrial flotation cell. INTRODUCTIONIt is well known that the effectiveness of froth flotation for separating different minerals is limited to the particle size range of approximately 10–100 mm (Trahar & Warren, 1976; Trahar, 1981). Fine particles tend to follow fluid streamlines around bubbles limiting the likelihood of bubble–particle collision, while coarse particles can be more easily detached from bubbles before collection can be achieved.Phenomenological models have been developed to quantify the physico-chemical aspects of flotation in order to better understand factors affecting these limitations, and to suggest ways of broadening the window of feasible flotation. Koh and Schwarz (2008) have incorporated these models into computational fluid dynamics (CFD) models of flotation cells, which have then been used for design and scale-up purposes (Schwarz et al., 2015). The models are based on dividing the process of bubble–particle interaction into three subprocesses: collision, adhesion and detachment. Of these, the hydrodynamics of bubble–particle collision and the probability of adhesion have been studied most extensively, while the dynamics of detachment have received relatively little attention from investigators."

Jan 1, 2016

By X. W. Yi, Z. J. Li, G. W. Ma

In this paper, the compressive strength and failure patterns of reinforced cemented paste backfill (CPB) were studied aiming to promote the stability of backfilled stopes. The concept of ductile backfill was proposed and a series of unconfined compression tests were carried out on both non-reinforced and reinforced cemented paste specimens. Portland cement (3% to 5% by weight of tailings) and five different types of ductile materials (0 to 0.5% by weight of solids) were employed in this experiment for the specimen preparation. The test results showed that inclusion of ductile materials enhanced the unconfined compressive strength (UCS), reduced the post peak stress loss and transformed the failure behaviour of specimens from classical brittleness to ductility. The strength of CPB reinforced with different proportions of polypropylene fibres was compared. The stress-strain curves illustrated that both cement and fibres contributed to the increase of UCS, but higher strain values at the peak stress were achieved by fibre reinforcement. CT sliced images acquired from X-ray computed tomography (CT-scan) demonstrated that the reinforced specimen developed irregular crevices at the edge of cross sections and gained the capacity of bearing large displacements owing to the mobilised tensile strength of fibres. It leads to the potential of avoiding unexpected falling blocks of CPB when adjacent mining occurs. This finding highlights a strategy to improve the self-supporting capacity of the fill mass with less cement usage and reduce the ore dilution rates when excavating to adjacent stopes.

Jan 1, 2015

By H. Tokuichi, H. Ohta, K. Sato

A physical separation technique of tantalum capacitors from waste print circuit boards is in a development phase in Japan. A tantalum capacitor consists of an exterior coating of resin (epoxy resin) mixed with silica fillers and a sintered tantalum compact, the latter of which is impregnated with manganese dioxide (MnO2). In this study, we developed a process to recover tantalum oxide from tantalum capacitors by roasting, fluidized-bed separation, and hydrometallurgical treatments. Our aim was to recover tantalum oxide with high purity from waste tantalum capacitors. In this process, the exterior resin was selectively decomposed by roasting without oxidation and pulverization of the sintered tantalum compact at a proper temperature. Furthermore, the decomposed resin with silica filler on the surface of the sintered tantalum compact was mostly removed by fluidized-bed separation. The surface of the sintered tantalum compact was cleaned by ultrasonic irradiation in an acid solution to remove the MnO2 paste as well as residual Ag paste and silica filler. The impregnated MnO2 in the sintered tantalum compact was leached as Mn(II) ions using acid solutions via the reducing effect of tantalum metal to recover purified tantalum oxide.

Jan 1, 2014

By F. Parada L

Two copper concentrate with medium and high enargite content were leached in a 3 L autoclave reactor under conditions based on the CESL process. Copper, arsenic, sulfur and iron were checked in all the experiments and antimony, zinc and molybdenum were evaluated in selected tests. The 98% of the obtained copper extraction is agree with others authors, but the behavior of arsenic, iron an sulfur have some differences. The solid residue was characterized by chemical analysis, DRX and QEMSCAN®. Finally a comparative analysis with neutral roasting as an option for the treatment of this concentrate is done.

Jan 1, 2014

By Richard Q. Fox, Joe L. Pinson

This paper provides guidelines jo1• analyzing and selecting electric power demand controlled. Error calculations, load selections and timing criteria are identified as the three key functions which affect the suitability of a demand controller for any particular application. The advantages of simulating the demand control application on a computer are described, and applications of a demand controller to an iron ore concentrator and a copper refinery are shown. Finally, the paper studies the return on investment for a demand controller.

Jan 1, 1976

By G. W. Diehl, G. A. Griffiths

"Gentlemen, one week ago, I attended the University of Minnesota's Annual Symposium on Mining, in Duluth. A good part of this symposium was dedicated to mill linings of rubber.At this symposium, three mining companies published results from long time full scale tests with rubber linings in mills at four different mines. These were the Republic and Empire Mines of Cleveland Cliffs Iron Company, the Groveland Mine of Hanna Mining Company and the Eagle Mountain Mine of Kaiser Steel Corporation. These papers will be printed in due time and I will not endeavour to relate their full contents, let me only say that in three of the plants, the linings were found to be very economical compared wi.th steel, and that these three are converting over completely to rubber linings, while the fourth, Empire Mine, reported no economical results as far as the shell lining goes, whereas the grates showed promise of becoming economical. The authors of the Cleveland Cliff's paper, however, stated that design improvements in the rubber lining possibly could result in an economical lining also for Empire Mine.That rubber linings in mills, in most cases, show better wear life than steel linings, is known by most of the audience. But, one thing that has not before been disclosed by the endusers is the effect of rubber linings on the grinding economy. All three papers mentioned above reported no change in capacity or grind and two of them reported a decrease in power consumption per ton ground. Hanna Mining reported an average decrease over a three year period for one mill of over 10%. This, of course, puts the economy of a rubber lining in a completely new light. Finally, a point of interest at this meeting was that all three papers emphasized the design aspect, Thus the industry has acknowledged what I believe to be a very important fact - the design of a lining is often more important than the material it is made of."

Jan 1, 1970

By P. J. van Staden

Several differences exist between the columns used for laboratory simulations of heap leaching and commercial heaps. Column walls support part of the weight of the ore and restrict the particle packing arrangements. Columns are typically of a diameter that is smaller than the dripper spacing to be used on the commercial heaps. The stacking practices that cause segregation and stratification on heaps are absent from columns. Intuitively, these physical differences would be expected to be the reasons behind the observed differences between column and heap leaching performance. But how can they be quantified, and what is the magnitude of the differences? Could some of these differences be built into column leaching experiments in order to better simulate commercial-scale heap leaching performance to ease the scale-up calculations from column leaching data? Alternatively, could heap construction practices be improved so that the ideal performance obtained in columns could be emulated on heaps? Data from a few heap leaching cases studies that permit direct comparisons between column and heap leaching performance is analysed, to reveal the extent of the differences in resistance to mass transfer. Discussion is provided on the implications for column and heap leaching practice, and for scale-up design procedures. INTRODUCTION Differences have been known to exist between leaching performance observed in laboratory columns and that of commercial-scale heaps. Both the heap leaching kinetics and finally achievable extent of extraction are generally found to be inferior in heaps compared to that achieved in columns. Heap leaching design engineers extrapolate the anticipated heap leaching performance by multiplying the time-axis of a column-leaching curve by a factor of about 2 and the extraction-axis by a factor of about 0.8, as explained by Jansen and Taylor (2002), Scheffel (2002), John (2011) and Scheffel, Guzmán, and Dreier (2016). The procedure is illustrated in Figure 1 by means of a hypothetical example. The solid line represents the leaching performance observed in a laboratory column, and the dashed line represents the anticipated leaching performance of a heap, extrapolated from the column leaching data using these empirical scale-up factors.

Jan 1, 2019

By I. Osvath, I. Gombköto, G. Mucsi, Z. Molnár

"In the present research, a deposited brown coal fly ash was used as raw material for geopolymer. The reactivity of the fly ash was altered using mechanical activation, which is one of the promising methods to improve bulk and surface reactivity. The mechanical activation experiments were carried out in a high energy density mill using 5 m/s circumferential speed, and various residence times (1, 3, 5, 10, 15 and 60 min). The effect of mechanical activation on particle size distribution was measured by a laser particle size analyzer and structural changes using FT-IR. Geopolymer samples were prepared from mechanically activated fly ash with an alkali solution. The progress of geopolymerisation was monitored using an Isothermal Conduction Calorimeter. The heat flow curve obtained indicated that reactions were more prominent and started much earlier in the mechanically activated samples. This observation is further supported by the compressive strength results which also improved in geopolymers using mechanically activated fly ash. Based on the obtained results, it can be inferred that mechanical activation is a possible way to enhance the reactivity of fly ash and consequently properties of resulting geopolymers.INTRODUCTIONCoal fired power plants generate fly ash and slag in huge amount worldwide, about 780 million tons/year (Heidrich et al. 2013). Due to the relatively low utilization rate, enormous quantities of these wastes are landfilled in ponds. The fly ash is the finest grained particle fraction of the solid ash, which is transported with flue gas, and removed by electrostatic or bag filters. The fly ash has pozzolanic activity, it does not react with water, but in the presence of calcium hydroxide solution hardens and solidifies, producing a reaction product practically insoluble in water (Opoczky, 2001). The most important property of the fly ash regarding geopolymerization is its reactivity, which depends on the chemical and phase composition, the dispersity (specific surface area, particle size distribution), and the morphology of the fly ash particles, and determined by the physical properties and chemical composition of the fly ash. Geopolymers concerning their chemical structure are polysialates, where the sialate (silicon-oxoaluminate) network is built up from the bonds of Si-oxide and Al-oxide by sharing oxygen atoms (Davidovits, 1988)."

Jan 1, 2016

By Deng Yang-wu, Zhang Yan, Chen Chun-fei, Luo Xian-ping, Luo Cai-gui

This paper summarizes the ecological imbalance status of abandoned rare-earth element (REE) mines in southern China. These include large areas of vegetation damage, serious water and soil erosion, landslides, mudslides, heavy metal pollution, water pollution, soil contamination, and fluorine pollution. The causes which lead to the ecological imbalances at abandoned rare-earth mines are analyzed, such as: the inadequacies of using vat leaching, heap leaching, and in-situ leaching processes to extract REE resources; low mineral thickness and low grade of REE ore; and low utilization rates of the resource. Southern ionic REE resources are not fully integrated, with limited access and ineffective supervision of REE mining by relevant departments. The ecological recovery research for ionic-type REE mines is lagging behind, and there is no deployable ecological restoration method for REE wasteland. In the end, the following suggestions are made to improve the ecological imbalance status of rare-earth mine in southern China: develop new rare-earth extraction processes, accelerate the integration pace of REE resources, increase investment in ecological restoration research in rare-earth wasteland, and so on.

Jan 1, 2014

By John Lund

INTRODUCTION GOLD-BEARING placers of Alaska and the Yukon Territories are buried under a layer of permanently frozen alluvial overburden, or 'muck', which varies in depth from twenty to one hundred feet. The placers, and the decomposed bedrock layers upon which they are deposited, are also permanently frozen. During the summer, surface muck which is exposed to the sun will thaw, but only to a depth of a few feet. To reach a valuable deposit, the frozen overburden must be either penetrated with shafts, or stripped from the deposit entirely. In either case, before the placer can be mined, it must be thawed. At modern dredging operations, the frozen muck is stripped from the placer by powerful jets of water from hydraulic giants. The placer, and several feet of decomposed bed-rock, are then thawed by forcing water through narrow pipes which have been driven into the deposit. Other methods of thawing frozen placers were used extensively during the early years of the Klondike 'gold rush', but experimentation later proved that creek water at its natural summer temperature was a more effective and economical thawing medium than any other which had been used. EVOLUTION OF COLD WATER THAWING Early prospectors of the far north reached placers by digging shafts through the frozen muck. They then thawed the placer sand and gravel by building wood fires at the bottom of the shafts.

Jan 1, 1951

By Chester J. Kuryliw

"The Geology of the Cochenour Willans mine, Red Lake district, was described by J. P. Nowlan in the Jubilee Volume. The complexity and intense alteration of the rocks obscured any clear relationship between ore and structure, and Nowlan recognized that future work might greatly modify the ideas then existing. This has proved to be the case. Subsequent detailed work has established the stratigraphic sequence in the Keewatin formations which are the host rocks of the orebodies, and has shown that the principal orebodies are confined to two adjoining bands of tuff.On this basis, it is now possible to map the complex structures with greatly increased accuracy. The amount of drilling and underground exploration required to find new ore has been much reduced, and indicated ore reserves are now substantially greater than at any time in the past. Daily production in 1955 averaged 187 tons per day at 0.578 ounces of gold per ton.The sequence of Precambrian events in the mine area is summarized in the following table:Intrusion of post-ore dykes.Ore formation.Intrusion of post-faulting, pre-ore dykes.Deformation: folding and shearing; alteration; faulting.Timiskaming sedimentation.Unconformity.Keewatin: volcanics and sediments, host rocks of the orebodies, described in detail in the next section.KeewatinFrom oldest to youngest, the Keewatin rocks in the mine area can be divided into six formations, which have been given local names:“Grey"" LavaA fine-grained dacitic to andesitic lava, amygdaloidal and locally containing well formed pillows. Certain areas are sheared and chloritized to a degree that makes identification difficult. The rocks are carbonatized throughout; the most persistent carbonate veins parallel the upper contact. Thickness more than 1,000 feet. (Minor mineralization, type 1 I -See section on Ore Formation)."

Jan 1, 1949