Search Documents

By A. Haque

"This paper describes an improved formulation of an analytical shear strength model developed by Haque & Kodikara (2012) by incorporating the failure of regular concrete/rock joints subjected to CNS condition. Sokolovskii’s analytical solutions developed for failure stress of slopes have been found to be effective in this regard. The analytical models have been validated for predicting the shear behaviour of concrete/rock joints subjected to various CNS loading conditions. The model has been found to accurately predict the dilation, normal stress and shear stress behaviour for a regular triangular saw-tooth joint up to the peak shear stress. Moreover, the peak shear stresses of concrete-rock joints with asperity angles ranging from 5 to 27.5o compared reasonably well with the available laboratory test results.INTRODUCTIONA new shear strength model for elastic regular triangular concrete/rock joints loaded under Constant Normal Stiffness (CNS) boundary condition has been developed by Haque & Kodikara (2012). The salient feature of this model is its capability of accurately estimating the normal and shear stresses of joints with shear displacements under CNS condition by incorporating the elastic deformation of asperities. However, the shear strength model of Haque & Kodikara (2012) for the elastic asperities cannot be directly employed to predict the peak shear stress of a joint experiencing plasticity under applied loads. Therefore, the model inevitability requires articulation of an appropriate shear failure criterion simulating the boundary conditions of the loaded asperity to predict the peak shear stress and corresponding normal stress and dilation behaviour of concrete/rock joints. Sokolovskii (1960) developed a set of analytical solutions for failure stress of slopes comprising c-??soils, which can be exploited effectively to simulate the failure condition as encountered for loaded regular triangular concrete/rock joints (Seidel & Haberfield, 2002)."

Jan 1, 2015

By R. M. T. Raja Ismail

Shipping and stevedoring industry is going to witness a massive increase in the amount of containers to be handled while land constraints become more critical. Offshore transfer operations hence offer a preferable solution to deal with the surge in cargos rather than to expand the port outwards. Recently, there has been increasing research interests on offshore crane automation. Suspended cargos in a ship-mounted crane system are caused to swing due to the vibratory motion of the ship induced by ocean waves, which can lead to collision between cargos and deck. Therefore, it is vital for offshore crane systems to satisfy rigorous requirements in terms of safety and efficiency. This paper presents the modelling and control development for offshore boom crane systems. A second-order sliding mode control law is proposed for trajectory tracking and sway suppression control, making use of its capability of actuator chattering alleviation while achieving high tracking performance and preserving strong robustness. The asymptotic stability of the closed-loop system is guaranteed in the Lyapunov sense. Simulation results indicate that the proposed controller can significantly reduce the effect of disturbances coming from gusty waves and other dynamic loadings.

Aug 1, 2013

By M. Phylli Bray

"Mining has the reputation of being a very ""macho"" industry. Recently, wider educational opportunities for women in nontraditional occupations and changes in mine technology have combined to make mining a viable career choice for women also. To benefit from this new resource, the mining industry faces the challenge of developing a different work environment from the one now burdened with sexism. Management supported initiatives are needed to facilitate such a transformation. The same rethinking of gender attitudes might also be extended to mining women in their traditional role as ""wife of"". The assumption that the male worker's wife is an unpaid adjunct is being questioned. It is suggested that women's separate concerns both as helpmate and as part of the mining workforce should be considered when planning for mining into the 21st century.IntroductionI must confess that, during the preparation of this paper, there have been many moments when I questioned my temerity. After all, I am not male, I am not an engineer, and I have never had a position in mine management. But as the wife of a mining engineer and a long-time resident of Northern Ontario mining towns, I do have an interest in the mining industry. This interest has had little to do with the technical and management aspects of the industry. Instead my research has been concerned with the impact the mining industry has on the people involved, particularly women, whether directly as employees or indirectly as wives. As I look toward the 21st century, I believe that the whole question of gender relations in the mining industry is one of the critical management issues smouldering below the surface."

Jan 1, 1995

By D. E. M. Plaumann

"The wet grinding of asbestos has attracted the attention of engineers for many years as a means of improving fibre liberation from the ore. Today, added impetus for wet grinding has resulted from a need to minimize worker exposure to asbestos dust in conventional dry mills using air, as well as a need to provide a cleaner, technically superior fibre for use by product manufacturers. However, high viscosities of asbestos slurries create transport and grinding difficulties which have been a factor impeding use of a wet grinding process.Laboratory evaluation of reagents to reduce viscosities of asbestos slurries found that one reagent, XFS-4272.00, reduced the viscosity of a 35% (by weight) slurry by 75%. The impact of XFS-4272.00 on actual grinding parameters were evaluated using a pilot plant rod mill. Slurries containing 78% solids and XFS-4272.00 were successfully milled and asbestos fibres from that milling compared favourably in liberation and relative surface area to asbestos fibres obtained from milling a 4% slurry without additives. IntroductionAlthough the use of asbestos has been declining over the last few years, the large deposits of chrysotile in eastern Canada (Quebec in particular) remain very important. Asbestos production in Canada stands ninth in volume for mineral production with over 740 000 tonnes produced in 1985. Of this quantity, 722000 tonnes were exported with a value of $446 million. Canada is second in world production of asbestos behind the U.S.S.R. The milling of asbestos ore has been done primarily by a series of steps involving crushing, dry-grinding and aspiration using large quantities of air to release the fibres. Contrast this process to those practiced in the purification of virtually every other mineral. Ores other than asbestos are crushed and milled using an aqueous slurry in rod, ball or pebble mills. The finely ground mineral, still as a slurry, undergoes beneficiation by froth flotation, heavy media separation, hydrocyclones or any of the other aqueous techniques currently employed in mineral processing.One of the driving forces behind the use of air instead of water as a means of separating asbestos is the nature of the aqueous asbestos slurry. While most slurries of minerals contain as much as 80070 solids and can still be pumped and transported, asbestos slurries become highly viscous with as little as 10070 solids. These high viscosities reduce the pumpability of the slurry and create severe handling problems. Mills become prohibitively large and uneconomical due to having to handle slurries containing only 10% rock and 90% water.Health-related issues have affected the use of asbestos in many countries. In Canada, the asbestos-producing provinces have introduced stricter occupational legislation to improve safety in the workplace. This primarily means strict control minimizing release of air-borne asbestos fibres . Quebec and Ontario have set limitations of airborne asbestos at 2 (2) and 1(3) fibre per cubic centimetre of air. With present milling technology, maintaining these low levels in the workplace requires constant vigilance."

Jan 1, 1988

By I. Protkova

Versa Power Systems solid oxide fuel cell (SOFC) stacks operate at intermediate temperatures 700 ? 800 °C allowing the use of metallic interconnects. Thermal expansion good matching with other stack components and cost restriction led to selecting ferritic stainless steels as interconnect material. Analytical tools and techniques were developed to understand the ferritic stainless steel behavior at high temperature while exposed to dual environment. Analytical tools such as X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) have provided valuable information towards describing interconnect degradation in a variety of testing conditions. Several examples are presented to demonstrate interconnect oxidation and its relation with SOFC testing results.

Jan 1, 2005

By A. Plugatyr, C. P. Baxter

"Bessemer matte iron content is a critical process parameter that needs to be closely monitored and controlled in order to achieve optimal Ni/Cu smelter returns. Current process control practices during Ni/Cu converting often rely on visual observations and typically involve matte sampling to confirm that target composition was reached. A high-level techno-economic analysis study was carried out to evaluate potential direct benefits of advanced process control during the final stages of Ni/Cu matte converting. The results indicate that the magnitude of direct benefits will largely depend on matte iron control practices already implemented as well as matte iron set point. Preliminary assessment suggests that under the assumptions used in this study, implementation of advanced process control can potentially result in additional revenues ranging from several hundreds of thousands to tens of millions of US dollars per year per converter producing about 200 tonnes of Bessemer matte per day based on Ni, Cu, and Co metal recoveries alone.INTRODUCTION Real-time measurement of molten metal elemental composition, arguably, remains one of the key unresolved issues impeding full automation and real-time optimization of pyrometallurgical operations in different industrial areas, including non-ferrous metals and ferro-alloys. In particular, current process control practices during Ni/Cu matte converting often rely on visual observations and typically involve matte sampling in order to confirm target matte composition. In addition to being time consuming, this approach relies heavily on operator experience and diligence, and, therefore, requires continuous performance and quality control efforts. For instance, the need to improve quality of the Bessemer matte (BM) at the Copper Cliff smelter has prompted an impressive staff engagement and training campaign that was carried out by Vale’s team in the late 2000’s (Zanini, Wong, & Cooke, 2012). This training exercise was executed to address the compounded effect of several operational challenges, namely demand for higher throughputs, changes in the feed concentrate composition, increased feed variability, loss of process knowledge and expertise due to retirement, as well as lack of a comprehensive approach to improving the overall performance of the flowsheet rather than meeting production targets for intermediate products. Although the campaign was very successful and has resulted in significant improvements in the Bessemer matte quality, it has also highlighted the need to move away from “the-art-of-converting” and develop analytical tools that would enable real-time process monitoring."

Jan 1, 2018

By Chandrakala Kari, Divyang Shah, Lakshmi Kanth Reddy, Kaushik Vakil, Sanjay Sarkar, Bhavin Desai

Gases rich in sulfur dioxide generated as a by-product of smelting and converting operations of copper concentrate contain selenium apart from zinc, lead, copper, cadmium, bismuth, antimony, and arsenic. The gaseous stream is heat exchanged in waste heat boiler, dust collected in electrostatic precipitator followed by cleaning in reverse jet scrubber to remove fumes, halogens and fine dust before passing to DCDA Monsanto catalytic converter to produce commercial grade sulfuric acid. The gas cleaning section of the acid plant uses water to scrub the smelting gases. During scrubbing, precipitated solids, known as sludge, settles at the bottom of the reverse jet scrubber containing 30 to 40 wt% copper and selenium up to 40 wt% selenium. In the existing process, the sludge collected during scrubber cleaning process is directly recycled to the smelter for copper recovery. However, the selenium is expected to again vaporize due to high oxidation potential during smelting and converting, causing accumulation of selenium in sludge. In present investigation, a roasting process has been developed to recover the selenium from acid plant sludge before charging it to smelter for copper recovery. Selenium is associated with copper in acid plant sludge as copper selenide, as determined by X-ray diffraction and electron microscopy. Thermodynamic and thermo-gravimetry study revealed that the copper selenide phase present in the sludge was amenable to oxidation at 600°C forming oxides of copper and selenium (Cu-Se-O). However, the dissociation of selenium from the copper oxide was made possible by sulfatation using sulfur dioxide between 450°C to 600°C, resulting into the formation of CuSO4(s) and SeO2(g). Lab scale experiments were carried out in vertical tubular furnace to determine the optimum roasting conditions with respect to roasting time, temperature and molar ratio of O2:SO2. Using these optimum conditions, selenium up to 90 wt. % in the form of SeO2 vapors could be recovered from the acid plant sludge in a large scale commercial roaster. Roasted sludge free from selenium and containing oxides and sulfates of copper could now be recycled in the smelter for copper recovery. INTRODUCTION There is an increasing demand for minor metals due to their use in innovative technologies. Similarly, the increase in demand for selenium is expected due to disruption in sectors related to renewable energy and photovoltaic battery. Selenium is a chalcogen and a non-metal with black or red crystalline appearance. Selenium is used in the glass industry to decolorize glass and to make red-colored glasses and enamels. It is also used in solar cells and as a photographic toner. Selenium is used as a brasses in stainless steel to improve its machinability. Selenium sulfide is used in anti-dandruff shampoos. In spite of the toxicity of its compounds, selenium is also an essential trace element for humans and animals. Selenium occasionally occurs free in nature, but more often occurs as selenides of iron, lead, silver and copper. There is an urgent need for the development of new methods for selenium recovery from the existing resources. Commercially, selenium is obtained only from anode mud produced during electrolytic refinery of copper.

Jan 1, 2019

By Y. Long

The deep-hole surface blasting technique is a prime method of iron ore mining. Blasting fragmentation is one of the important economic indicators that measures the blast method to obtain the iron ore. To improve the efficiency of the blasting method and further reduce the cost of the subsequent processing of iron ore, this paper summarizes measured data gained from a certain amount of blasting test conducted in an iron ore mine in Guangdong province, China. According to the data analysis, there are differences on iron ore blasting fragmentation by different indicators of deep-hole blasting, such as decoupling coefficient of charge, contact state between charge and borehole wall, and change of detonation position in charge. These factors were compared in terms of relevance and impact. Research shows: under certain rock conditions, the decoupling coefficient of the charge has a best range related to blasting fragmentation. Since the detonation position in charge determines the direction of propagation of the explosion stress wave through ore and rock, bottom initiation and mid initiation will help to improve the iron ore blasting fragmentation in joints fractured rock and ore. The research conclusions have important application value for program design of iron ore surface blasting and to guide other types of rock surface blasting.

Aug 1, 2013

By C. Gu

Flow field design is critical for PEM fuel cells. The flow field design can affect reactant distribution to the catalyst surface, water management, thermal management and current collection. Therefore, it has tremendous impacts on the fuel cell performance and durability as well as reliability and operational flexibility. In this paper, an optical method is used to study the reactant distribution in the flow field channels of two commonly used flow field designs, straight channel design and serpentine channel design. Images of the flow patterns are shown followed by discussions of the flow patterns.

Jan 1, 2005

By J. Elbrond

"This paper describes qualitatively the progressive are losses and rock dilution in a mining project from the geological modelling to and including the concentration. A simple theoretical model of the net present value of a deposit, assuming a log-normal grade frequency function, is used to find the pair of decisions on rate of production and cut-off grade, which maximizes the net present value. Various degrees of ore losses and rock dilution are then applied on this optimum, and the resulting decreasing net present values are calculated, as well as the increasing cost of metal and the increasing metal losses as a function of are losses and rock dilution.IntroductionDue to a variety of uncertainties, to inevitable lack of precision in deposit estimation and in mine planning, and due to production constraints, ore losses and rock dilution occur throughout the many phases of a mining project. The phases range from the geological definition of the orebody, over the cut-off grade optimization and decision, over the design of the mining method and the actual mining to the ore dressing, where the final loss of valuable ore into the tailings occurs. Quantification of ore losses and rock dilution are mostly difficult if not simply impossible to obtain. At the end-phase an estimate of the total dilution may be obtained with some degree of precision by observations of the amounts and analysis of concentrate and tailings. It is much more difficult to estimate the total ore losses because the uncertainty of the geological modelling in the initial phase and in the mining phase is very difficult to quantify, despite the use of geostatistics for grade estimation.Many attempts at quantification of ore losses and rock dilution have been made and some examples are shown in Table I. Although they differ widely from each other, it is obvious from these figures that ore losses and rock dilution are significant and have considerable effects on the economical results of a mining operation. Life length, net present value, cost of producing metal and the loss of metal are all affected."

Jan 1, 1994

Who is ArcelorMittal Mines Canada ?One of Canada's leading suppliers of iron ore to steel markets around the world ?Past company name = ??Quebec Cartier Mining?? ?Operator of one of North America's largest open-pit mines ?Mont Wright Mines ?Fire Lake Mine ?Largest ArcelorMittal iron ore mining subsidiary ?Annual production of 15 million tonnes of concentrate ?Major expansion program to 24 MT/Y ?Internationally competitive pellet plant ?9.0 million tonnes annually

May 1, 2011

By M. Tadie, J. Wiese, K. Corin

The use of potential control in the flotation of ores has been applied in a variety of operations and presents an opportunity for improvement of selectivity and recovery of valuable minerals. Although it is possible to vary the redox potential (Eh) using chemical additives such as sodium hypochlorite or hydrogen peroxide this is more commonly done by varying the pH and dissolved oxygen (DO) concentration. The present study involves an investigation into the effect of varying dissolved oxygen concentration, ionic strength (IS) and pH on the flotation response with the aim of application to a South African lead-zinc ore. In all cases the Eh is measured as a function of the different DO, IS and pH values. The main objective was to achieve selective flotation of galena from sphalerite. The first part of the work was micro-flotation tests conducted on single minerals with galena used as the basis for effect of the factors studied on redox potential and ultimately recovery. The DO was varied by alternating between the use of air and nitrogen as the gas source to the micro-flotation cell. PH was varied between pH 9.2 and pH 11.8 using sodium hydroxide. In the first part of this study a factorial design approach was used to determine the interactive effects of the variables tested, viz. DO, ionic strength and pH, on the Eh and on the recovery. Redox potential was measured using a combination electrode made up of platinum wire and Ag/AgCl reference combination. Recoveries indicated that pH had the most significant effect on recovery and Eh. The influence of redox potential on recovery was found to be of relevance to the condition of high dissolved oxygen concentration and less so at low dissolved oxygen concentrations. It was also noted that that the combined interaction between ionic strength and dissolved oxygen concentration had a positive effect on recoveries, however this was not so with Eh. The chemistry of the ions in solution was observed to play a dominant role on the recovery due to changes in solubility arising to pH modification. The longer term objective of this work is to determine the optimal Eh conditions for the separation of galena from sphalerite.

Jan 1, 2016

By Robert D. Brown

"All ten Canadian provinces have now tabled their 1981 /82 budgets . Only the provinces of Ontario, Quebec and British Columbia made more than minor modifications to their tax structures, with both Ontario and Quebec imposing major tax increases. In the past year, the federal budget was also released in the spring. Not so this year: we have that to look forward to in the fall!This month, Tax Notes presents a brief summary of the more significant tax changes introduced at the provinciallevels in the last months.Summary of provincial tax rate changesThe tax changes in this year's provincial budgets were both up and down- but there were far more tax increases than tax cuts.At the corporate tax level, two provinces, New Brunswick and British Columbia, increased their general corporate income tax rate; the former by two percentage points and the latter by one percentage point. Quebec, rather unexpectedly, sharply cut its corporate tax rate on business income, but increased some of its other business taxes at the same time. British Columbia reduced its corporate tax rate on small business income by two percentage points and Saskatchewan by one percentage point."

Jan 1, 1981

By E. Larsen

Marine tailings disposal may in some cases be the best solution to one of mining’s major environmental problems. The public standing of this solution is poor, partly because of past bad practices. Among the tailings problems spreading of super-fines and toxic substances stand out. The two are often interrelated as heavy metals, insoluble to sea water, tend to adsorb on fines and spread piggyback on them. Only one paper seen, has addressed the mineralogy of fine particles in suspension. The topic was a secondary tailings deposit. Studies on the sedimentation of fines in large river estuaries show that different minerals sediment sequentially as the salinity of the river increase. Mineralogy in the particle size range where particle separation takes place, has so far, naturally been in focus for the mineral processors. Next to nothing is known about the fines which may cause environmental problems. Tailings disposal has, due to its complexity, to a large extent been taken over by specialists in other fields, biologists, engineering geologists, chemists. The basics of the subject ought also to be given more input by the mineral processing community. A drawn out battle about tailings discharge into some fjords has taken place in Norway. The detractors focus at fine particles (could be dangerous nanoparticles) spreading and emphasize the effects. Calculation is simple: 5 million tonnes tailings annually discharged, containing 1 wt. % < 1µm determined by laser diffraction, results in 50 000 tonnes of nanoparticles let loose in the environment. The industry`s difficulty to answer, is lack of basic research on this topic. Test work to develop a methodology to address the problem is described. One thing the mineral processors know is that final tailings may be comprised of tailings from separate separation processes, with different properties, some of which may require special treatment. One tailings stream from a Norwegian mine is investigated in such a context.

Jan 1, 2016

By Michel Garon

"Several years ago computer control of the flotation process was successfully implemented at the Matagami concentrator of Noranda Mines Inc. At that time this was the first computer application being installed at this operation. The last few years have seen an extensive use of programmable controllers in areas such as the copper and zinc dewatering circuits and the lime preparation system. With the aid of such instruments, these areas have attained a high level of automation and as a result, a high degree of efficiency. The controllers have proven to be very dependable and easy to use.IntroductionThe Matagarni Division of Noranda Mines Inc. operates two mines in the Matagami District of northwestern Quebec which is located about 650 km northwest of Montreal. The mines ship ores to a central concentrator whose throughput averages 95,000 tonnes of ore per month. Metal contents of the mill feed average 0.9 per cent copper and 5.0 per cent zinc. Concentrate outputs are approximately 3,200 tonnes of copper and 8,200 tonnes of zinc per month.The concentrator commenced operation in 1963. An on-stream X-ray analyzer was installed in 1968, providing analyses of several samples in the flotation circuit without the aid of a computer. In 1974, control of the circuit by computer was added to the system. As a result, zinc flotation efficiency improved considerably and reagent costs decreased through the reduction of copper sulphate consumption.In the past few years it was realized that significant improvements could also be made in other parts of the operation . Copper and zinc dewatering circuits and the lime preparation system were identified as major areas that could drastically benefit from automation. In 1982, programmable controllers were seriously considered as an attractive alternative for achieving the company &apos;s goal. Because of their relative lowcost and their high degree of flexibility, they were selected for implementing automation and, for improving the efficiency in each of these areas."

Jan 1, 1985

By W. Basuki, B. Setyotomo, L. Hakim, R. Hendrajaya

Due to high crack sensitivity of slab product of gas and oil line pipe application, its steel making process and alloy composition were evaluated and then improved to overcome its critical solidification process and reduced surface defects. The study was conducted at Slab Steel Plant Krakatau Steel. The purpose was to improve slab surface quality by reducing surface defects so that the slab surface doesn&apos;t need to be totally repaired. The method applied was by performing plant trial process, which the secondary process parameters such as alloying method and the casting parameters such as casting powder selection, metallurgical cooling, mould level control, and superheat were continuously monitored and then adjusted to the surface quality of the product. Based on the calculation of Ferrite potential of the steel, the chemical composition was designed to achieve optimum casting parameters in order to avoid high shrinkage during solidification. The results of the study are decreased surface defect quantity, and smooth casting process. The quantity of crack decreased by almost 90%. The slab surface repairing was significantly reduced from 85. % to less than 10%. These new casting parameters and developed alloy composition are then used and standardized for the mass production of the steel.

Jan 1, 2005

By Robert B. Parsons

"The new Ontario Liberal government introduced its first budget in October. The changes to The Mining Tax Act proposed in the budget are mean t 10 simplify the current system without any loss of revenue to the government. It goes without saying that some operators will benefit from the changes while others will pay more taxes after 1985.With regard to ongoing matters at the federal level, the proposed carve-out legislation and the issue of northern allowances are being discussed with government officials, and a small victory has recently been scored with regard 10 the laxation of certain share transactions of prospectors and grubstakers. A report on these issues is provided herein.Ontario BudgetOn October 24, 1985, Ontario Finance Minister Robert F. Nixon tabled a budget proposing several significant changes to both the Ontario Mining Tax Act and the province’s income tax legislation.Mining Tax ActA flat rate of tax and reduced processing allowances highlight proposed changes to The Mining Tax Act. The proposed changes, with a comparison to the existing system, are set out in Table I.The most significant change is the replacement of the graduated tax rate schedule with a flat 20010 tax rate. This is a welcome change for most mine operators who viewed the high rate of 30% on profit over $20 million as counter-productive.However, the flat rate of ta x may not be welcome to all operators. Generally speaking, operators with less than $ 10 million annual profit are better off under the graduated rate system, while operators with annual profit exceeding $10 million will benefit from the 20010 tax rate."

Jan 1, 1986

By K. MacMaster

"This paper deals with the history, development, present and future of the Employee Assistance Programs in place at the Inco Ltd. operations in Thompson, Manitoba. It should be noted that, although many similar programs exist in various industries and jurisdictions, these programs had to be fine-tuned to meet the needs of Inco employees, having in mind the helping professional resources available in Thompson and its geographic location. IntroductionIn the late 70s, many Canadian industries and the Canadian Labour Congress and their affiliates commenced discussions on the value of the Employee Assistance Program (E .A.P.) philosophy to both management and labour.In the contract signed between Inco Ltd., Manitoba Division and Local 6166, U.S.W .A. in 1981, a commitment was made to establish a joint E.A.P. for the hourly workforce in Thompson, Manitoba. With this background and sequence of events in mind, it is appropriate to explain the methodology and the steps that were taken for the implementation of the hourly program. Development of Hourly ProgramIt was agreed by the company and the union that the committee to develop the program should consist of equal numbers from both sides: three active union members plus an advisor representing the Union and three supervisory personnel plus an advisor representing the Company; in addition, a person familiar with E.A.P.s from the Alcoholism Foundation of Manitoba was to act as a facilitator. The Union appointed a social worker who was working as a counsellor for union members as their advisor , and the company appointed a staff employee who had worked voluntarily in the field of alcohol and drug abuse for many years. The makeup of the committee was extremely important in order to give credibility to the entire process. The makeup of the committee is shown in Table 1.The facilitator selected from the Alcoholism Foundation of Manitoba was well known in the community and highly respected in his profession."

Jan 1, 1989

By M. Labrie, H. L. Gibson, G. Doiron, J. J. Watkins, D. H. Watkinson

The Corbet deposit is one of 17 proximal Cu-Zn massive sulfide deposits located. within the Noranda Cauldron which occurs within the core of the Noranda Volcanic Complex. The deposit is located at the top of the Havrian Formation, the lowermost formation of the 3000 m thick Mine Sequence; the deposit has Yielded 2.75 M tonnes of ore grading 3% Cu, 0.96% Zn, 2.06 g/t Ag and 1.0 g/t Au. The multi-lens Corbet deposit formed within a 250 m wide crater that occurs within a localized breccia pile. The Corbet breccia pile was constructed by explosive magmatic and hydrovolcanic eruptions localized along the south flank of a larger andesitic shield volcano that formed during the waning stages of Havrian volcanism. The breccia footwall of the deposit allowed unfocused and widespread hydrothermal discharge that resulted in the development of a large area of chlorite and fringing sericite alteration that exceeds, by six times, the size of the sulfide lenses and represents a significant exploration target.

Jan 1, 1993

By Mohamed Hamoud

Relative permeability curves represent an important element of special core analyses, but challenges remain in obtaining valid results and the extrapolation and use of existing permeability results is problematic. This situation is compounded in cases where core properties are altered from changes in effective stress. During the production of oil and gas reservoirs, the effective stress changes as a result of changes in pore pressure or temperature. Therefore, changes in rock properties such as porosity and permeability will occur and will consequently influence reservoir performance calculations. An experimental program was carried out to understand the behavior of dense, reconstituted sand samples at low effective stress states. Drained triaxial compression tests were set up to study the effect of stress alteration on relative permeability data through porous media. Initially, a saturation stage was performed followed by isotropic loading to bring the core sample to reservoir fluid and stress conditions. Then, while axial (deviatoric stress) loading was applied to the sample, a series of absolute and relative permeability tests was performed under steady state flow at different levels of strain during pre and post peak shearing stress. The stress-strain behavior results from the study revealed that the absolute permeability decreased during isotropic loading (compaction) and increased during shearing (dilation). However, the shape of relative permeability curve changed from contraction to dilation and showed higher initial kro and the lower initial kro respectively. The goal of this project was to understand the behavior of both absolute and relative permeability at different stresses. It is expected that geomechanical processes will be adopted for special core analyses to support the current integration of geomechanics into reservoir engineering. This will be required if, during SAGD, conventional and/or unconventional reservoir simulation, reservoir engineers implement a proper set of relative permeability data at each in situ state of stress, instead of constant curves throughout the field?s life.

Jun 1, 2012