Search Documents

By Pierre Choquet

"The whole work carried out both in situ and in laboratory by a research group of the West German collieries is presented. This work has led to a design method of steel arch supports for gate roadways that gives full satisfaction in this particular coalfield. The method accounts for mining depth, the mining system (advancing or retreating), thickness of the coal seam and other parameters.Full statistics are then given on gate roadway supports of the ECCS (European Community for Coal and Steel) coalfields. They were collected by the author in order to show that the West German method can be applied to other coalfields as the long wall systems which are generally being used are very similar. Design calculations are conducted for each coalfield's case. They show that the method would have been able to predict in most cases the support actually used.Utilization of the design method is recommended to the Cape Breton Development Corporation 's mine operators because mining conditions, even though different from European ones, present a number of similarities which make it possible to apply the design method to their particular case.This procedure might be profitable in mines facing support problems in their levels and for any planning of future projects"

Jan 1, 1986

By Michael S. Moats, Alex Luyima, Tomas Oliveira

Some commercial copper electrowinning facilities use Cyquest N-900 (a polyacrylamide) or HydroStar (a modified polysaccharide) to improve the density and smoothness of copper electrodeposits. However, the effects of these additives have not been studied extensively in the open literature. Thus, the electrodeposition of copper at 40 oC from a non-stirred synthetic electrowinning electrolyte (40 g/L Cu2+, 160 g/L H2SO4, and 20 mg/L Cl-) in the presence of various concentrations of either additive was evaluated using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). CV results show that neither additive has much effect on the nucleation overpotential of copper electrodeposition on stainless steel. However, Cyquest N-900 polarized the copper deposition reaction upon the return sweep. The EIS data indicates that Cyquest N-900 increases the reaction’s charge transfer resistance and creates a second low frequency loop. HydroStar had minimal effect on the electrochemical data generated by CV or EIS. Thus, the mechanism by which HydroStar affects the copper deposition reaction still needs to be determined.

Jan 1, 2014

By Peter Harben

"This paper discusses the benefits of industrial minerals, their sources of supply, price and marketing trends, and their increasing use as substitute materials and ""strategic"" minerals. IntroductionKaolin finds have yet to spark the kind of frenzy associated with the 1849 California gold rush; no dolomite deposit has ever gained the notoriety of the Comstock Lode; and few industrial minerals are counted among the currently fashionable list of "" strategic mineral s"". Nevertheless, the glamorous zhine associated with metals may be somewhat superficial; further digging provides perhaps the real foundation of modern society - industrial minerals.They are often tagged as common, everyday materials that are simply dug out of the ground, crushed and hauled to a local point of consumption. Although this description is accurate in the case of road aggregates, sand and gravel, and the like, there are many exceptions to this rule. The term industrial minerals is rather nebulous, covering as it does the mundane and esoteric, the chemically active and the refractory, the $2 and the $10m-a-ton product. All of these minerals influence every facet of modern life from fertilizers to fire retardants, ceramics to cars, construction to clothes, and toothpaste to tennis courts. Their usefulness is well illustrated by the variety of industries they serve; the main ones are listed in Table 1. It is now time to dismiss the notion of non-metallics as the ""third world"" of natural resources business after the metallic and energy products by dispelling some of the myths regarding abundance, variety and value of the group's sixty-plus products."

Jan 1, 1982

In terms of throughput, product size and power draw, grindcurves provide a measure of the response of the mill performance to changes in mill operating parameters ? usually mill filling. Since presenting the principle in 2006, grindcurves have been applied to a wide variety of AG and SAG mills. Mill response has been carefully measured for variations in: mill fillings from 15% to 40%; throughput by a factor of two; power by 50%; feed blends; liner profile; and mill speed from 65% to 80%. The outcomes of this extensive program of work are presented as the measured grindcurves. How they have enhanced our understanding of mill operation and how they may be applied to practical daily mill control is discussed. It is proposed that this technique provides a viable and valuable mill control tool that may find extensive application in the industry.

Jan 1, 2012

By R. W. Thompkins

"PREFACEPart 1 of this paper, published in the September issue, covered the occurrence of uranium, radiation from uranium ores, the uranium series, radioactive theory, radioactive equilibrium and application to the radon series, the working level, the theory of emanation and diffusion, transport by thermal diffusion of radon emanating from porous rocks, and definitions.The October issue carried Part 2, which dealt with radiation theory applied to uranium ores, other radon migration factors, factors affecting the radon gas release rate, the measurement of radon gas emanation rates, the tunnel concept, variation of emanation rate with grade and estimating radioactivity from grade analysis.Part 3, in this issue, concludes the series by discussing the techniques for controlling radiation and providing some example calculations.17.0. Techniques for Controlling Radiation17.1. Altering the Factors In the Diffusion EquationIt has been noted that radon gas emanates from the surfaces of exposed ore to the mine atmosphere. The diffusion laws establish the rate of this flow. The fundamental relationship is that the rate of flow (J) is a function of the pore concentration and the distance from the surface. It is expressed as: []If any of these terms is varied, either naturally or artificially, the rate of gas emanation will be altered.Altering the Diffusion CoefficientThe literature describes many ways to lower the radon gas emanation rates which are dependent on changing the diffusion coefficient:1. A layer of ice on top of a tailings dam or on a soil.2. Humid clayey materials and swamped soils over a radon source."

Jan 1, 1982

By S. Amira

In the last two decades, many new creep-resistant magnesium alloys have been developed for high temperatures applications. Their mechanical performance and corrosion behaviour were reported for various experimental conditions. However, these conditions often led to uneven comparison basis. In the present study the microstructure, mechanical properties and corrosion performance of four of these newly developed creep-resistant magnesium alloys were systematically compared. Specimens were obtained from experimental box-like components that were die-cast and thixocast in comparable conditions. Their mechanical and corrosion properties were compared using similar testing conditions. Results show that the creep resistance, strength and impact resistance of specimens are comparable but systematically lower compared to specimens cast under optimized conditions. The reduced concentration of elements such as Al, Ca, Sr and Ce lead to a decrease of the corrosion resistance of the magnesium alloys in 3.5% NaCI solution.

Jan 1, 2007

By L. A. Melis, A. R. Marchbank, S. A. Webster

"Certain northern Saskatchewan uranium ores have a high content of nickel and cobalt which offer the potential for recovery as a by-product to uranium. A nickel/cobalt recovery process has been developed as a viable method of recovering a marketable concentrate from typical uranium raffinate solution.Impurities are first removed from the raffinate and the pure solution is then treated with sodium carbonate to recover a bulk nickel/cobalt carbonate precipitate for sale to a primary nickel producer. All contaminants of concern are removed to very low levels and the product is free of radioactive contamination with gamma emissions significantly below natural background. Cost estimates have shown that installation of a nickel/cobalt recovery circuit within a uranium process plant is economically feasible.The testwork that led up to the selected process is described along with recommendations for further investigations such as additional testing of hydroxide precipitation as a possible viable alternative to carbonate. The selected process is described and project economics are briefly reviewed.PROCESS TEST PROGRAMBackgroundExtensive metallurgical research has been performed over the years to develop a process for recovering uranium from the Midwest deposit in northern Saskatchewan. During the course of this research, a certain amount of information became available which suggested that recovery of nickel and cobalt from uranium raffinate could be economically feasible. It was decided to undertake a test program which would investigate methods of separating nickel and cobalt from radioactive and other metal contamination to permit production of a saleable product.Available technology suggested that three general approaches could be taken to recover nickel and cobalt. The first and simplest approach would be to selectively precipitate the impurities of concern, primarily arsenic, iron and radium, and then recover a bulk concentrate from the purified raffinate. The second approach would be to purify the raffinate and then remove cobalt from solution by solvent extraction producing pure nickel and cobalt solutions for further treatment. The third approach would be to precipitate all metals from solution and then selectively re-dissolve nickel and cobalt in ammoniac solution which would be further treated by solvent extraction for nickel recovery, leaving cobalt for further treatment."

Jan 1, 1993

By G. P. Demopoulos

"The recovery and separation of platinum-group metals (PGM) from primary and secondary materials currently attracts a lot of interest due to the high value of the metals and their increasing demand for high-tech applications. Thus, the traditional refining processes are gradually replaced by newer more efficient separation techniques such as solvent extraction and ion exchange. In this paper the classical and modern refining techniques are reviewed and the pertinent solution chemistry dictating proper processing strategies in each case is discussed. The technological advantages of the modern separation methods are emphasized and reference to the recovery of PGM from primary as well as secondary materials is given. INTRODUCTIONDue to their outstanding physicochemical properties, such as catalytic activity, conductivity and corrosion/oxidation resistance, precious metals now find extensive usage outside of the traditional jewellery and investment industries. The increasing use of precious metals in such areas as electronics and catalysis, as well as their increasing high value, has led to a growing interest in their recovery and separation from primary and secondary materials.Quantitatively the demand of platinum metals in the western world by area of application is described in Table I. Platinum and palladium represent 90% of the total demand, Rh and Ru 8% and the remaining is taken by Ir and Os. In terms of value the following were the average prices (US$/oz) of the metals in the second half of 1986: 500 Pt, 125 Pd, 1200 Rh, 650 Os, 400 Ir and 80 Ru. Due to these prices, exploration, mining, reclamation and refining activity were very high in South Africa, the biggest producer of Pt metals in the world, as well as in other areas: United States (Stilwater deposit), Canada (Sudbury, Marathon and Lac des Isles, Ontario; Kenly Lake, Quebec, etc.), Australia, Europe and elsewhere"

Jan 1, 1989

By A. R. MacPherson

"This paper considers four aspects of autogenous grinding. Part 1 discusses statements on power efficiency of autogenous grinding compared to conventional crushing and grinding systems. It also demonstrates how high-power efficiency can be obtained from autogenous grinding systems. Part 2 considers a simple method of testing ores to determine the type of autogenous plant which can treat these ores on a commercial basis. A comparison of testing for simple small plants vs large plants or complex ores is included. Part 3 considers important aspects which have to be considered in proper design of an autogenous grinding system. Part 4 discusses problem ores and how they can be treated in an autogenous system. INTRODUCTIONAfter about 35 years of using autogenous grinding plants in the mining industry, it is perhaps time to review where we are with this, by now, relatively old development. Autogenous grinding in this paper means grinding run-of-mine ore by fully autogenous means or by using a ball charge to assist the grinding (semi-autogenous). Also, autogenous grinding can be eitherby dry or wet.The use of autogenous grinding in the fifties was making its slow start, and it was not until the sixties that more of the mining industry would consider its use . By the seventies, most builders of new plants would have considered autogenous grinding, whether they used it or not, in the final design.In the eighties, most large plants use autogenous mills and to reduce over-all operating costs, many older conventional plants are now looking and actually retrofitting these old plants with autogenous grinding mills.It is evident that many misconceptions concerning autogenous grinding are still current. Some come from improperly designed plants which result from poor test work. There are many considerations in the proper design of autogenous plants. Some ores have been found to give problems even in a well designed plant. These ore types are beginning to be classified and recognition in the test stage allows steps to be taken in the design so that these ores can be efficiently handled in autogenous grinding plants.Therefore, this paper will address the following aspects of autogenous grinding:1. Misconceptions regarding autogenous grinding.2. Testing of ores to ensure a well designed commercial plant.3. Important considerations in mill design.4. Difficult ores, their recognition and types of design to handle such ores."

Jan 1, 1989

The fracture behavior of second phase particles and the role of matrix material on the wear resistances of the three Al-Si alloys containing 8, 17, and 19% Si were investigated using single pass scratch testing technique by applying normal loads between 0,15 and 5,00 N, in ambient air, Optical microscopy and SEM with EDS were used to analyze microstructures and morphologies of scratch tracks of the Al-Si alloys, The results showed that needle-like Si particles fractured under a load of 0.50 N, while block-like Si particles fractured at loads above 3,00 N, The Al-17% Si alloy with large number of needle-like particles (area fraction 16,4%) exhibited the highest coefficient of friction (0,8) and the widest scratch track, The Al-19%Si alloy containing high Si percentage and larger number of block-like particles (area fraction 16%) exhibited the lowest coefficient of friction (0,37) and the narrowest scratch track width. Presence of block-like particles was effective in reducing the amount of material transfer from Al-Si alloy surfaces to the counterface.

Jan 1, 2005

By D. M. Ward, J. H. Ahrens

"The Fond-du-Lac uranium deposit was delineated primarily by percussion drilling and a small program of diamond drilling. Drillcore samples from three diamond drill holes as well as digitized gamma logs from percussion and diamond drill holes were utilized to define and implement an algorithm for the conversion of gamma-log data to equivalent-grade data. The procedures and detailed analysis for the provision of assay data for uranium reserve estimation are documented.IntroductionThe Fond-du-Lac uranium deposit is on the south shore of Lake Athabasca, approximately 2 km southeast o f Fond-du-Lac , northern Saskatchewan. It is on the northern rim o f the Athabasca sandstone basin.A train of mineralized glacial erratics was discovered in 1967 by Farnok, Limited by means of a helicopter-borne radiometric survey. In 1969, a program of diamond drilling by Famok was successful in locating in-situ mineralization in the Athabasca sandstone at the apex of the mineralized boulder train. Since 1974, exploration and development work have been performed under a joint-venture agreement between Eldorado Nuclear Limited and Famok Limited, with Eldorado acting as operator.From the discovery drill hole to the development of the gamma-log to equivalent-grade con version algorithm, the deposit had been tested by a total of 222 drill holes, 210 of which were percussion holes and 12 of which were diamond drill holes. The holes are generally vertical and collared at 10-metre centres on fences spaced 20 metres apart. The deposit is approximately 390 metres long, 10 to 40 metres wide and up to 45 metres deep, and is generally confined to the Athabasca sandstone. Uranium occurs as pitchblende, coffinite and uraniferou s goethite."

Jan 1, 1983

ABSTRACT The SART (sulphidization, acidification, recycle, and thickening) process is an effective way to separate copper and cyanide in the waste stream of gold processing plants using cyanidation. Factorial experimentation has been conducted to create models of copper recovery, cyanide recovery, acid addition, and oxidation/reduction potential during SART. Economic analysis of the resultant models showed that SART is best operated with a sulphide-to-copper molar ratio of approximately 0.56, pH of 4, and a minimized cyanide-to-copper molar ratio. The experiments also showed th0at residence time can have drastic impacts on SART performance.

Jan 1, 2013

By Robert B. Parsons

"It is generally felt that flow-through shares face a bleak future under the set of tax rules proposed in the federal government's tax reform white paper. Industry and government circles are beginning to give thought to alternatives to flow through as a mechanism for facilitating equity financing in the exploration industry. Despite suggestions that grants and tax credits may someday be on the table, industry is sticking to its position that there is no substitute for flow-through. Alternatives toFlow-throughProposals in the federal government's tax reform white paper have cast significant doubt on the ability of the mining industry to raise risk capital after 1989by way of flow-through shares. There is serious concern that introduction of the ""cumulative net investment loss"" (CNIL) rules, the phase-out of the mining explorati0! 1 depletion allowance (MEDA), and the Increased capital gains inclusion (750/0 versus 50%, at present) will make the economics of flow-through so unattractive after 1989 that these shares will hold little appeal to most investors. The question might be raised, then, as to what alternatives exist by way of tax or other government assistance that could help the exploration sector.The purpose of this paper is to survey the types of government incentives that could be of some value to explorationists and to the mining industry in general. For the past several years, flow-through has been in the spotlight insofar as incentives to the exploration industry are concerned. Other potentially useful and attractive incentives have been partially hidden in the shadow of flow-through. These incentives, in certain circumstances, can be of considerable benefit, and should not be ignored."

Jan 1, 1988

By Sudarshan Martins

The measurement of acoustic signals produced by a tumbling mill has been previously used to determine the operating state of the mill and correlate the variations of the sound intensity with the operating conditions of the mill. Separately, the discrete element model (DEM), a software simulation of the mill, was developed to provide insight into the operation of the mill. Presently, there has not been much work reconciling the DEM simulation of the mill with the acoustic signal. Working from basic principles of linear, time-invariant systems, agreement between an acoustic DEM simulation and the measured signal is sought. First, the impulse response function of the mill is measured. The DEM provides the forces applied to the mill shell as a function of time. A convolution of these simulated shell forces and the transfer function gives the simulated acoustic signal. This signal is compared to the measured acoustic signal, both in the time domain and the frequency domain. Finally, a discussion of the results is given.

Jan 1, 2012

By D. A. Stokes

"In October of 1980, Fording's 15 000-ton capacity clean coal silo was put into operation. The silo was unique in that it was designed to allow the mass flow of material, coupled with a sophisticated computer-controlled dynamic loadout/weighing system.On May 1, 1982, an explosion, attributed to a methane buildup, devastated the top of the silo. .As a contingent plan to minimize the effect of the production loss the conveyance to the silo top was reconstructed and the silo' was back in operation by mid-June 1982, although the silo top was left open to prevent further methane buildup. As dust emissions occurred during loading ofthe silo, an extensive study was undertaken to establish dust control for the silo, while at the same time providing methane detection and control.The study, conducted for Fording by the Cambrian Engineering Group of Calgary, involved an extensive search and investigation of existing coal silos. The study concluded that there IS no universally accepted method of controlling methane emissions in coal silos.The study also produced a unique conceptual design for handling methane, while at the same time, protecting the environment . Fording's Clean Coal SiloThe silo, located at Fording Coal's Fording River metallurgical coal operation, is utilized for the storage and load out of cleaned thermally-dried metallurgical coal.The silo was constructed in 1979 and 1980 to reduce unit train loadout times and to facilitate the handling of “special shipments"" of coal. The silo went into operation in October 1980, under manual control and utilized computerized, automated loading by February 198I.The silo is 21 m in diameter and 76 m high, with a nominal capacity of IS 000 live tonnes. The coal storage portion of the silo is 21 m in diameter and 48 m high, utilizing 2 steep-angled hopper outlets allowing mass flow of the stored coal during train loading. Each hopper has a control gate and a discharge chute, one chute for bulk loading, the other for trim loading of coal into the rail cars."

Jan 1, 1986

By Scott K. Palm, Neil D. Pearson, Jr. Read

"Uncertainty is an important feature of many investments, but it is especially important for mineral properties. Mine properties often entail large investments and fixed commitments. Managers in the mining industry often view price uncertainty as undesirable, due to the possibility that the price of the mined commodity will fall to a level that prevents the firm from recovering its investment and fixed costs. This paper identifies pitfalls in conventional valuation methods and outlines a new approach to valuation based on option pricing theory and dynamic programming. In the process, it identifies generic strategies for organizing mine production in ways that allow the owner to benefit from the uncertainty in mineral prices. IntroductionRisk is pervasive in the mining industry. The operation and maintenance of a mine may involve high, and unavoidable, fixed costs. A mine owner can only begin to recover these fixed costs if the price of the mined commodity is greater than the incremental cost of production. But the prices of many minerals are extremely volatile. The price volatility of copper has been significantly higher than the price volatility of a typical stock, for example. A mine owner cannot be sure that the price of the mineral product will remain high long enough for the firm to recover its capital and fixed costs.Mine owners are able to minimize their losses during periods when the output price is below the incremental cost of production by temporarily closing operations. During these periods they incur only fixed costs. While shut-downs help minimize losses, the y do not help the firm recover its initial investment. If output prices remain low long enough, the fixed costs and original investment may never be recovered. High fixed costs, therefore, lead to substantial downside risk."

Jan 1, 1986

By F. Kapeller, G. Herget

"The need for monitoring the effect of changes in ground stresses due to mining in hard rock has existed for many years. The Mining Research Laboratories of CANMET, EMR have developed a new tool which monitors with high precision the radial deformation in boreholes. The result is the Mining Research Laboratories strain monitoring system (MSMS) which uses the highly stable and very sensitive vibrating wire principle to monitor deformations in relatively large boreholes, e.g. 76 mm to 153 mm diameter.The vibrating wire is strung across a relatively large proving ring and operates at a frequency between 600 to 1800 Hz. The read-out system is based on continuous vibration.The ring is installed with a hydraulic tool and brought into contact with the surrounding rock through precisely machined and guided wedges. The resolution of the system is in the neighbourhood of 4 x 10-4 min/ Hz. The data collection can be carried out with a portable read-out unit and provisions are available for automatic data collection. Stresses may be calculated from strain readings.The system was tested in cooperation with the Centre de recherches minérales at the Niobec Mine in Quebec for the purpose of monitoring the effects of drill drift development and slope mining on surrounding ground stresses.After access was available to the site, 153 mm diameter holes were drilled for the determination of in situ ground stresses. These holes were then used to install the strain monitoring system. The effect of drill drift development and production blasting in stopes C-203-13 and C-203-15 on ground stress distribution could be observed clearly.The horizontal relaxation in the core of a pillar which occurred during mining of adjacent rooms was between 0.082 mm to 0.111 mm. Calculations of stresses from these deformations indicate that the rock material is still in an elastic condition.Roctest of Montreal has obtained a license on the manufacturing and distribution rights. A patent has been registered and CANMET will assist in installation of the MRL strain monitoring system and the interpretation of records."

Jan 1, 1989

By L. M. Guayacán-Carrillo, G. Armand, A. Noiret, D. Seyedi, S. Ghabezloo, J. Sulem

"The main purpose of this paper is to analyze the convergence measurements in a drift excavated in the Callovo-Oxfordian claystone. The drift axis is in the direction of the major principal horizontal stress whereas the stress state is quasi-isotropic in the drift’s section. The initial geometry of the drift being circular, the anisotropic character of the deformation is taken into account by assuming that the drift shape evolves in an elliptical shape. The convergence measurement data on six different points around the drift are analyzed to identify the main axes of the deformation ellipse, following the methodology proposed by Vu et al. (2013, Rock Mech Rock Eng, 46, 231-246). Then, using the semi-empirical law proposed by Sulem et al. (1987, Int J Rock Mech Min Sci, 24, 145–154), the convergence evolution is fitted independently for each axis of the ellipse. This method permits to distinguish two effects: the face advance effect and the time-dependent behavior of the ground. The results for the two directions of the ellipse axes show very close values for the parameters describing the time-dependent properties of the ground, the distance of influence of the face, and the extension of the decompressed zone around the gallery. Such model can provide valuable insights for predictions of the convergence evolution in the long-term. INTRODUCTIONDeep disposal of radioactive waste has been studied in France for more than two decades. The French National Radioactive Waste Management Agency (Andra) began in 2000 the construction of an Underground Research Laboratory (URL) with the main goal of demonstrating the feasibility of a geological repository in Callovo-Oxfordian claystone. Several research programs have taken place to improve the knowledge of the rock properties and its response to the excavation progress. The optimization of supports design for long-term behavior is an important point to develop. A network of experimental drifts has been constructed with variations on: excavation method, structure geometry, supports system and orientations with respect to in-situ principal stresses’ directions. In each drift different sections have been instrumented to monitor the convergence evolution and the rock deformation. Continuous monitoring of the excavated zone around the drifts revealed the development of a fractured zone (extensional and shear fractures) induced by the excavation. The extent of this fractured zone depends on both the drift orientation and the in-situ stress field (Armand et al., 2014). Indeed, the fractures distribution has an important influence on the convergence of the drifts."

Jan 1, 2015

By S. S. Rahman, A. Gholami, M. A. Aghighi

"This paper provides a foundation for studying the growth of fractures in presence of other discontinuities and different anisotropies of low permeable hydrocarbon formations and helps to improve the design strategies for multistage fracturing.The multistage fracturing technology has recently been used to exploit low permeable hydrocarbon reservoirs. However, the mechanism of hydraulic fractures interaction and the impact of local heterogeneities on ultimate trajectory of the growing hydraulic fractures are not yet understood in depth. A fully coupled poroelastic Finite Element based model is developed to investigate the mixed mode propagation behaviour of growing hydraulic fractures. This model takes advantage of an explicit representation of the fracture which enables us to take the effects of rock and fluid related parameters into account. Moreover, impact of fracture geometry and leak-off phenomenon is investigated. The refined mesh around the crack provides the added advantage of more detailed stress distribution, pore pressure change and back stress in the vicinity of the fracture and in particular at the fracture tip. The potential deviation propensity of the fractures is evaluated based on the fundamental rule that fractures propagate perpendicular to the direction of the minimum horizontal stress.This study shows that pressurization of transverse hydraulic fractures results in the reorientation of local principal stresses, particularly in vicinity of fracture tips. Variation of flow patterns clearly influences the evolution of shear stress around the fracture tips which will potentially lead to mixed-mode I and II fracturing and consequently, fracture deviation. The presence of local heterogeneities such as preexisting fissures and/or fractures is a main source of such pore pressure induced stress redistribution and reorientation and potential deviation of hydraulic fractures.Most existing models ignore or simplify the effect of pore pressure/stress coupling as well as the fracture geometry and fluid flow within the fracture. Also, the fluid leak-off from the hydraulic fracture into the formation, which is a controlling factor in fracture growth, is often considered using analytical models. Taking advantage of a fully coupled porelastic model along with an explicitly discretized fracture, this study provides a more realistic insight into the complex fracture propagation processes of multistage fracturing operations particularly in presence of reservoir geo-mechanical complexities."

Jan 1, 2015

By J. B. Mitchell

Using digital image correlation the evolution of strain and strain at the onset of localisation resulting in a hot tear has been determined for alloys AA6111 and Al¬0.5wt% Cu during solidification. High resolution images of hot tear formation and growth were captured during a constrained bar test that incorporated a glass window above a central hot spot region. The images were analysed using digital image correlation software to measure the evolution of displacement and strain based on tracking the motion of discrete features on the as-cast surface of the sample. Temperature data was also acquired with a thermocouple cast into the sample in close proximity to the hot tear. The interval starting from the point immediately after solidification shrinkage ends (the metal pulls away from the glass) and finishing when the first sign of a crack or hot tear is visible to the eye was used to determine strain data. The minimum strain at which strain localisation occurs was found to be 0.0069 in AA6111 and 0.0021 for A1-0.5%Cu.

Jan 1, 2007