Search Documents

By C. Zangerl, H. Lechner

"Large scale rock slides in deeply incised Alpine valleys are common hazards that can endanger human life, settlement areas and critical infrastructure such as highways, railways and reservoirs (Bonzanigo et al., 2007). In order to perform reliable forecasts of the behaviour of rock slides influenced by large dam reservoirs the geometry, the kinematics, the deformation behaviour and the hydrogeological situation need to be understood profoundly. Based on generic rock slide models the influence of the rock slide geometry on the stability as well as the impact of the buoyancy forces and water load of the reservoir at the toe of the slope are the main focus of this study. Various assumptions of hydraulic conductivity, groundwater conditions of the rock slide and impoundment depth of the reservoir are analysed using limit equilibrium approaches.Generally, deep seated rock slides are characterised by deformation along one or multiple shear zones where most of the measured total slope displacement localizes. Many large rock slides, especially those observed in foliated, mica-rich crystalline rock masses (e.g. paragneisses, mica schists, phyllites), do not fail suddenly or reach high velocities. Instead, many of them move slowly and reach velocities of centimetres per year or even less. Some show episodic accelerations, sometimes reaching alarming levels, but then subside to non-critical levels again. However, there is a potential that deep-seated rock slides fail rapidly, develop into far-reaching run-out rock flows, and cause catastrophic events. Whereas the role of triggers in promoting phases of acceleration is often understood, the same cannot be said regarding the kinematics and dynamic processes by which the rock slide mass decelerates, re-stabilises or accelerates to a catastrophic degree once the trigger impetus has been removed. Thus key questions of the presented work concern the geotechnical, geometrical and hydrogeological conditions under which a slowly moving rock slide is triggered to accelerate to irreversible, maybe dangerous velocities. The development of the sliding zone is generally influenced by pre-existing discontinuities such as brittle fault zones, shear and tensile fractures, foliation and bedding planes. These geological structures determine the geometry of the sliding zone which can either be rotational or translational. During the gravitationally induced failure process the geometry of the rock slide undergoes a change.Several observed post-failure geometries in metamorphic rocks show a concave topography in the middle to upper part of the rock slide and a typical convex or bulge-like topography at the toe of the slope (Zangerl et al., 2012). Whereas the sliding zone of the upper part of such a rock slide mass is rather steep and planar, the inclination of the sliding zone at the toe can be close to zero and act against the driving forces (Alonso et al., 2010). A shear zone that meets alluvial deposits at the foot of the slope encounters a stabilizing impact on the mechanical behaviour. This buttressing effect of alluvial sediments has a remarkable influence on the slope stability."

Jan 1, 2015

By Simon C. Dominy, Alwyn E. Annels, Mark A. Noppé

Abstract - Mineral Resources and their subsequent conversion to Ore Reserves are of key importance to mining companies. Their reliable estimation is critical to both the confidence in a feasibility study, and also to the day-to-day operation of a mine. Together with sampling, assaying, geological and other errors introduced during interpretation and estimation, additional errors are likely to be introduced during the application of technical and economic parameters used for conversion of resources to reserves. There is thus a requirement for high-quality interpretation and estimation to be supported by high-quality data. Any company expecting to make sound investment or operational decisions must base this on both relevant and reliable information. An Ore Reserve statement generally contains a single set of grade and tonnage figures without a discussion of the potential inherent errors in these estimates. Some sensitivity studies may be run, but confidence limits are rarely quoted and, if they are, often do not take into account many of the factors that cause uncertainty in the grade and tonnage estimates. Mineral Resource and Ore Reserve estimates thus carry certain errors leading to uncertainty and risk; some of these are unquantifiable for various reasons, for which the operator should be aware. This paper presents a review of the potential sources of error that might occur during a resource estimation program, which are carried through into the reserve estimate. A number of methods are discussed that allow the estimator to be more transparent about the inherent risks in his/her estimate. Emphasis is placed on data quality, and the requirement for strong quality management to be linked to continuous improvement.

Jan 1, 2002

By C. Anderson, H. Huang, P. Miranda, E. Dahlgren, I. Chandra, M. Jeffrey

The latter part of the 20th century saw great advances in the treatment of refractory gold ores coupled with increased reliance on the use of cyanide for gold processing. Now, in many parts of the world, there is social pressure to limit or eliminate the use of cyanide. As well, treatment of some refractory ores or concentrates which have excessive cyanide consumption, gold cyanide pregrobbing or significant sulfide content remain difficult. This paper will outline the history of the development of alkaline sulfide leaching as an ancillary process to nitrogen species catalyzed (NSC) pressure leaching. Electrochemical fundamentals and the applicable thermodynamics of the alkaline sulfide hydrometallurgical system will be outlined. As well, examples of refractory gold recovery with alkaline sulfide hydrometallurgy such as an arsenopyrite gold concentrate application, a chalcopyrite gold concentrate application, a pregrobbing gold ore application, and a cyanide consuming gold ore application will be delineated in this paper.

Jan 1, 2005

By J. J. Benitez

MIBC (methyl-isobuthyl carbinol) was previously shown to enhance significantly sylvite flotation when used at the stage of preparation of amine dispersions. In this paper Atomic Force Microscopy (AFM) is used to study the effect of MIBC on deposition of octadecylamine (ODA) on the surface of mica. The AFM images indicate that amino terminated, and therefore hydrophilic, deposits of ODA are observed on the mica surface in the ODA dispersions free of MIBC. In the presence of MIBC a methyl terminated (hydrophobic) monolayer is obtained on the mica surface. The transition between the monolayer and bilayer phases is due to the presence of MIBC. Experiments carried out in distilled water reproduced the results obtained from the brine. Working in pure water instead of brine simplifies the preparation conditions and the analysis by AFM.

Jan 1, 2006

By G. Shen, W. R. Tyson

In most fracture toughness test standards, such as ASTM E 1290 and BS 7448, crack-tip opening displacement (CTOD) is measured by using three-point bend (SE(B)) or compact (C(T)) samples with deep cracks. The loading mode and crack depth in these tests sometimes are different from that of pipelines. Pipelines usually have shallow defects and experience tensile loading when the supporting ground moves. As a result, the CTOD measured by these samples is lower than that of pipeline in tension. Recent researches suggest using single-edge-notch tension (SE(T)) samples to measure fracture toughness for pipelines. In the present study, shallow and deep SE(T) samples under fixed grip loading were analyzed by using the finite element technique. An equation to relate the CTOD to the area of the load/plastic crack mouth opening displacement (CMOD) is proposed. With this equation, the CTOD of a SE(T) sample can be evaluated by measuring the area under the load/plastic CMOD curve of a SE(T) sample.

Jan 1, 2005

By W. R. Bacon

"MAGNETITE HAS BEEN found in many .parts of the coastal area of British Columbia, but the more important deposits are on Vancouver Island and Texada Island. The locations of these deposits are shown on Figure 1.Interest in the magnetite deposits dates back to the 1870s, when land was acquired on the southwest coast of Texada Island by the Puget Sound Iron Company. This ground included the Prescott, Paxton, and Lake deposits. During the years 1885 to 1903, and 1908, 28,898 tons of magnetite ore was shipped to the company's blast-furnace plant at Irondale, Washington, U.S.A. This production was almost entirely from the Prescott open-pits.In the years following the Texada Island discoveries, other magnetite deposits were found in the coastal area, and various plans were proposed to utilize the local ores in the establishment of a steel industry in the Pacific Northwest. None was carried to fruition but, in 1951, open-pit mining was begun at Iron Hill, Vancouver Island, to furnish iron concentrates for steel mills in Japan. In 1952 mining of the Texada deposits was resumed to supply the same market. Production figures for these recent operations are as follows:"

Jan 1, 1949

By K. Soldenhoff

Mantra Resources Ltd is developing the Mkuju River project is southern Tanzania. The uranium deposit, hosted in ?Karoo? sandstone, is surface outcropping with the majority of uranium mineralisation occurring in the finer clay component of the ore. A flowsheet, consisting of ore beneficiation, acid leaching, RIP uranium recovery and direct precipitation of the uranium product, was developed and successfully demonstrated in continuous mini-plant operations at ANSTO. The selected flowsheet overcomes the difficult slurry rheology, arising from the clay component of the ore, by eliminating the need for a CCD plant. The RIP process was found to contribute to a high uranium extraction, by eliminating ?preg-robbing?, at a relatively low acid addition in leach, with the potential to eliminate ferric ion and oxidant additions.

Aug 1, 2010

By D. Y. Li, C. D. Ma, T. Zhou, T. J. Cheng

In this paper, a number of experimental tests are carried out to study the strength difference on rectangular prismatic marble specimens with different height-to-width (H/W) rations. The specimens have a nominal size of 45×15 mm in the compressive cross-section (W×T) and different heights (H = 22.5 mm, 45 mm, 60 mm and 90 mm). It is to say that the height-to-width ratios are equal to 0.5, 1.0, 1.33 and 2.0, respectively. The quasi-static uniaxial compressive tests are finished by a servo-controlled INSTRON machine (the strain rate at about 10-5/s), and the dynamic compressive tests are finished by a diameter of 50 mm cylindrical SHPB apparatus (the strain rate reaching about 101/s). The rock failure process of marble specimens is captured by a high speed camera in order to distinguish the fracture propagation behaviour. It is found that the compressive strengths increase when the H/W ratio of marble specimen changes from 2.0 to 1.0 due to the end clamping effect both for quasi-static and dynamic loads. However, when the H/W ratio changes from 1.0 to 0.5, the apparent compressive strengths decrease both for the two loading conditions. The strength decrease of short marble specimens may be attributed to the change of failure mode from shear to slabbing, which can be identified by the fracture patterns of the specimens. Based on the uniaxial compressive tests, the slabbing strength of the marble was found to be about 40% of its UCS for the specimens with a nominal height-to-width ratio of 2.0. In addition, it is found that the dynamic increase factors (DIF) are affected by the specimen’s aspect ratios. It implies that the same aspect ratios should be used to compare the dynamic and static compressive strength of rocks. Meanwhile, both the static and dynamic tensile strengths of the marble are obtained by the Brazilian disc tests. The ratio of the dynamic tensile strength to the static tensile strength of the marble is about 2.68.

Jan 1, 2015

By Abani R. Samal

The Fe assay values from the diamond drill-holes within a magnetite deposit of magmatic origin are utilized in this study. Only assay data from the unoxidized magnetite mineralization was utilized. The data from the overlying hematite mineralization zone was not used. A threedimensional block model estimated using ordinary kriging (OK) is used for analysis purposes. To estimate the non-linear standard deviations (s) and the confidence intervals (CI) of block estimates a discrete Gaussian variogram model is used in this project. The change-of support coefficient (rv) and the block-support correction are used in the ?block-anamorphosis?. A new calculated value of rv is 0.7283, implies that its influence in the block-anamorphosis is not significant. The CIs are calculated from the block-gaussian variables; then back transformed to the raw values. At 95% probability, the CI for the kriged block estimates of Fe values are calculated using Gaussian kriged estimates of the Fe and the corresponding standard deviations (Gaussian). The results indicate that the block estimates with a high influence from relatively small amount of samples can be identified as high-risk estimates.

Oct 1, 2009

By D. Nie, M. Ren, T. Mo

This paper studied the phenomenon of room temperature creep deformation at crack tip and its effect on fatigue crack growth rate of a X-70 pipeline steel using compact-tension (CT) specimen on a MTS 810 testing machine. Time-dependent deformation at the crack tip under constant load was observed in this steel at room temperature and the amount of deformation produced was seen to depend on loading rate and the magnitude of stress intensity factor. It is found that there exists a critical stress intensity factor below which the deformation decreases with time when the applied load remains constant. It is also found that the occurrence of room temperature creep obviously affects the subsequent fatigue crack growth rate. The observed behavior was explained based on dislocation theory.

Jan 1, 2005

To date, improved thickening of clay mineral dispersions presents major technological and environmental challenge to mining and mineral processing industry worldwide. Flocculant-assisted dewatering processes currently employed during thickening are far from being efficient, requiring further development and process optimisation for dramatic improvement. In this paper, recent studies carried out to modify (i) pulp chemistry, (ii) flocculation performance and (iii) particle interactions to significantly improve the dewatering behaviour of flocculated, model and plant smectite and kaolinite clay dispersions are presented. It is shown that pulp pH-mediated hydrolyzable metal ion hydrolysis and specific adsorption in tandem with high molecular weight flocculant and shear may synergistically act to significantly enhance the dewaterability of both clay mineral pulps. Furthermore, polymeric flocculant structure type is demonstrated to show clear links with floc shear sensitivity, and hence, flocculation performance and pulp dewaterability. The implications and relevance of the findings plant clay mineral waste tailings thickening operations are drawn.

Jan 1, 2006

By P. R. Goad

"Kidd Creek is a large volcanogenic base metal sulphide deposit, located near the west end of the Abitibi greenstone belt, 27 km north of Timmins, Ontario. The rhyolite geology is characterized by a NNE-striking and steeply east-dipping package of rhyolite volcaniclastics upon which has been imposed a strong ESE-striking and north-dipping structural fabric . Massive rhyolite units with grey-black. chloritic cores and yellow, sericitic margins intrude as dykes into the stratigraphic footwall and as sills higher in the stratigraphy. Massive rhyolite units positioned near the top of the felsic pile exhibit an extensive marginal development of hydraulic fracturing and are termed crackle-brecciated rhyolite.The stringer sulphide zone is positioned in a lobate blanket of crackle-brecciated rhyolite at the top of the felsic pile. The stringer sulphide zone is characterized by a mature chemical alteration, being specifically depleted in alkalis and enriched in iron-rich chlorite. with accompanying silica, sericite and carbonate alteration. A suite of trace elements characterizes this mature alteration. The massive rhyolite units, which intrude lower in the rhyolite volcaniclastics, exhibit a core of weak chlorite alteration and strong marginal sericite alteration. Tight or unfractured massive rhyolite units are essentially devoid of sulphide mineralization and exhibit a suite of trace elements characteristic of this immature alteration. It is interpreted that the massive rhyolite units intruded into an already evolving system and ""choked-off"" active conduits carrying hydrothermal fluids and subsequently acquired an immature alteration signature. Rhyolite units positioned higher in the pile developed intense hydraulic fracturing and a mature alteration coincident with the formation of the stringer sulphide zone. In summary, a model, based strictly upon the rhyolite geology, is reviewed to assist in the exploration for volcanogenic base metal sulphide deposits."

Jan 1, 1985

By J. Shibata, N. Murayama, H. Yamamoto

As one of effective usages of wastes discharged in the non-ferrous metal industry, the syntheses of AlPO4-5 and hydrotalcite were carried out using aluminium dross as a raw material. AlPO4-5 is an aluminium phosphate condensate with properties of zeolitic materials and large pore size. Hydrotalcite is an inorganic anion exchanger and has a layered structure of complex hydroxide. They were synthesized in an autoclave at high temperature and pressure. Various physical properties such as crystal structure, surface texture, and specific surface area were measured. AlPO4-5 can be synthesized from aluminium dross under hydrothermal conditions at 180°C-200°C, and 3h. At the same time, AlPO4-34 and non-porous AlPO4 were also formed as by-products. The crystals of AlPO4-5 have a hexagonal structure. Lt is desirable to heat the reaction product at around 550 °C to remove tri-ethyl amine. The specific surface areas of the reaction product before and after heat treatment at 550°C were 17.9m2/g and 358m2/g, respectively. Hydrotalcite can be obtained by a co-precipitation method from the aluminium dross and waste MgCl2 solution discharged in the aluminium regeneration process. Small amounts of SiO2, Al2O3, and Fe2O3 remain in the reaction product as an impurity component. The interlayer distance of the obtained reaction product is about 0.3 nm. Hydrotalcite changes to Mg-Al oxide during calcination at 500 °C for 3h, and then hydrotalcite is formed again by a rehydration operation. The physical properties of the reaction products obtained from the wastes were very similar to those from fresh reagents.

Jan 1, 2004

By Free. Michael L.

Crushing ore prior to heap leaching enhances mineral liberation and creates fine particles that may require agglomeration to avoid permeability problems during leaching. Conventional modeling is relatively successful in describing general fluid flow and extraction in heaps. However, most models do not adequately account for the effects of mineral liberation and exposure or the effects of agglomeration, curing, and loading on heap leach performance. This paper will discuss methods to account for mineral liberation and exposure as a function of comminution. It will also discuss methods for incorporating liberation, exposure, and mineral locking as well as curing and fluid flow in heap leach modeling. It will also provide information regarding agglomeration and the effect of loading in heap leach modeling.

Jan 1, 2014

By A. Zarei-Hanzaki, O. Golmahalleh, S. M. H. Hosseini, H. Azizi-Alizamini

The main importance of acicular ferrite microstructures arises from their desired combination of mechanical properties in comparison with the bainite and ferrite-pearlite microstructures. Several factors affect the microstructural transition from bainite microstructure into the acicular ferrite one. As is well established any factor corrupting the prior austenitc grain boundaries nucleation potential, such as the thin layer of allotriomorph ferrite and the austenitc deformation inhomogenities may promote the acicular ferrite formation instead of bainite. Accordingly, this study deals with the effects of the aforementioned features on the acicular ferrite formation in low carbon microalloyed steel. The results indicate that the formation of strain-induced ferrite at the prior austenite grain boundaries accompanied by deformation inhomogenities in the austenite grains change the effectiveness of allotriomorph ferrite on acicular ferrite formation from active to inert one.

Jan 1, 2004

By J. A. Finch

Solvent-coated air bubbles in the Air-Assisted Solvent Extraction (AASX) process achieve the dual role of high solvent specific surface area and ease of phase separation. The thickness of the solvent film is of fundamental interest but difficult to measure directly in the process itself. As an approach interferometry (in the UV-vis region) was used to measure the time dependent thickness of a film formed by blowing an air bubble in kerosene-based solvents. The film was stabilized by the presence of 1.5 ppm silicone oil, as employed in AASX. The film appears to comprise two layers; an outer "free" layer of almost constant thickness and an inner "bound" layer which decreased in thickness with time. The bound layer is considered relevant to AASX. For a 20 mm diameter bubble blown in LIX/kerosene solvent the initial thickness was ~ 3 um which decreased over 10 minutes to a final rupture thickness of 500 nm. The bound layer thickness and time to rupture decreased with decreasing bubble size. Correspondence to prior indirect estimates of solvent layer thickness is examined.

Jan 1, 2006

By V. Prodanovic, M. Militzer

Production of advanced linepipe steels with strength levels of 685MPa (100ksi) and higher requires excellent control of runout table cooling to produce the desired final fine-grained microstructures, which may include acicular ferrite. Cooling is exerted on the runout table by applying water jets onto the hot surface of the strip and heat is removed from the steel by forced convective boiling. The associated boiling mechanisms are complex and include film, transition and nucleate boiling. A pilot-scale runout table test rig has been built to systematically study boiling heat transfer from a moving steel plate by employing industrial scale headers. Experiments were conducted using test plates moving at speeds between 0.3 m/s and 1.4 m/s. The plates were cooled down from 850°C to temperatures below saturation by a single water jet supplied through an industrial size circular nozzle. Based on these experiments heat fluxes were determined and further used to develop improved runout table cooling models.

Jan 1, 2005

By D. Mu

A method is presented for evaluating the effective gas diffusion coefficient of porous media. A series of random-distributed porous solids with different porosity are generated, a solution of the gas diffusion equations inside the porous media is obtained using the finite element method (FEM), and then the effective gas diffusivities are computed. The results show that there is a percolation threshold sp, and this percolation threshold decreases with an increase in the connectivity of the pore network; the relationship between the effective diffusivity and the porosity is strongly nonlinear when the porosity £ is less than about 0.2; and is quasi linear for higher porosities. The threshold decreases with increasing the connectivity of the pore network. A formula relating the effective diffusion coefficient with porosity is proposed.

Jan 1, 2005

By Z. Mubarok

An overview of the problems encountered the electrorefining of copper anodes containing high levels of nickel and antimony is presented. Our investigations have been focusing on the passivation behaviour of the anodes with high contents of Ni, Sb, Sn, and Pb, the formations of kupferglimmer and floating slimes. The results of linear voltammetry, chronopotentiometry and electrolysis test revealed a noticeable lower resistance of the anodes to passivation in comparison to those with lower contents of Ni, Sb, Sn, and Pb. Anode containing kupferglimmer exhibited oxygen gas evolution during the passivation state. Scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) indicated that tin can replace and/or join antimony in the kupferglimmer structure. Under specified experimental conditions, floating slimes precipitations took place with high Ni, Sb, Sn, and Pb anodes prior to the end of one anode period.

Jan 1, 2007

By Larry M. Southwick

Processing of ores to recover metals usually generates large amounts of waste materials, such as rejects from concentrating operations, tailings from leaching and slags from smelting. These wastes often contain substantial amounts of iron and other metals, recovery of which are often considered to be of commercial value. Earlier versions of this paper investigated a number of processes built to recover iron from a variety of copper processing residues. This paper will extend that coverage to residues from nickel/cobalt, aluminum, asbestos and oil shale processing and coal plant fly ash. Products of interest are iron, ferroalloys, magnesium and aluminum. While none of these processes achieved long-term commercial success, their efforts cover the gamut of problems that must be addressed in treating dirty and difficult materials to recover generally low-value products. An Adept is an alchemist who can create a Philosopher's Stone, which could transmute base metals into gold. In 1701 in Berlin one Johann-Freidrich Böttger, a nineteen year old apothecary's apprentice, told King Frederick I that he could discover how to make the Stone. He failed and fled Frederick's wrath to Poland. He failed again, and King Augustus II threw him in jail. Then, in 1709, he discovered instead the secret of making Dresden china, certainly a more practical search. His failures in alchemy led to the nickname Adeptus Ineptus.

Jan 1, 2004