Search Documents

By S. V. Burr

"IntroductionOne of the more puzzling geological enigmas, in the writer's opinion, is how rock can move sideways with respect to other rock. In the writer's study of regional northwest-southeast folding in North America (Burr, 1980), he may have found the answer to horizontal offset.Horizontal OffsetSideways movement or horizontal offset does not mean that the movement was, or is, horizontal. As indicated below, the actual movement may be at a high angle from the horizontal. However, it is the horizontal VECTOR, or offset, which is measured on surface by geologists. Vertical movements (thrust, normal, reverse) can be understood, as they involve blocks of rock , generally separated on four to six sides, which have been pushed up or subsided. Vertical faulting across dipping strata can produce APPARENT horizontal offsets. However, this thesis deals only with ACTUAL offsets.The ProblemFigure 1 is a plan view of a simple hypothetical horizontal offset. Three vertical dykes are intersected by a fault lineament. Two dykes exhibit no movement; the middle dyke has been offset a distance (a). Vertical faulting would have produced no horizontal offset. How can a horizontal distance (a) disappear or appear? Rock expands or contracts in infinitesimal amounts.SolutionThe map (Burr, 1980) shows the writer's interpretation of regional northwest-trending folds in Ontario. The writer made two observations about horizontal offsets during his thirty year study of these folds:1) All major horizontal fault lineaments strike at a high angle to the northwest fold axes. Many of the northwest-trending lineaments are fault s, but their movement is essentially vertical.2) Close to many of the known horizontal offsets (and several lineaments), there are areas where plunge reversals are so frequent and close together it is impossible to draw in all the fold axes at a scale of 1 inch = 4 miles, and, in the highly faulted Espanola area southwest of Sudbury, Ontario, all the indicated folds cannot be easily separated at a scale of 1 inch = 1 mile. The writer has observed folds less than 30 feet apart next to the strong Puskitamica-Chibougamau fault in northern Quebec."

Jan 1, 1982

By Don McColman

"Tires, although not always the largest single cost item in open-pit mining operations, will place in the top three, along with explosives and fuel. How this high-cost supply is controlled is dependent upon on an efficient tire program. The success of this program is, in turn, dependent upon the people who are directly associated with tires and their use, namely: the mine's tire personnel, the tire sales representatives and a technician for the rubber company. The technician will relay his observations and information received from the mine personnel back to the manufacturer with recommendations to overcome current problems .Haulage truck tire life and costs in a hard rock open-pit mine are governed and controlled by four important factors:I) Field control.2) Operating within manufacturer's guidelines.3) Different tire purchasing methods.4) Scrap piles.Field ControlPerhaps the most influential people involved in this program are those who live with the tire through every hour of its lifespan: the truck driver, the shovel operator, the dozer operator, the grader operator and the shift boss. Of these, the truck driver has the most control, in that he can drive over or around rock s as these situations arise. The loading area, the edge of the haul road and the dump account for most of the tire injuries.This is why shovel, dozer and grader operators must appreciate their influence on haulage tire life. Spillage cleanup must be ongoing and is not being done adequately if any of these operators are idle. The shift boss that drives by a rock on the road without removing it or calling for a cleanup has little recourse with the truck driver who runs over it-he has sanctioned the driver's actions by his own neglect."

Jan 1, 1986

By Mike McKevitt

We are trying to promote a concept and a change in management?s approach to the iterative process of grade control. This is important as grade control must routinely try and achieve the long term objectives set by the mine plan ??BackgroundBackground ??Factors contributing to variation from planFactors plan ??Basis of OptimisationBasis Optimisation ??Ore Block Optimisation processOre process ??Operating mine examplesOperating examples ??Chain of Mining. ??Intention is to highlight the need for repeatable and consistent materialand material-type classification to remain consistent with the Life of Mine Plan ??We can drill another hole or reWe re-optimise a plan, but once excavated, the final decision has been made ??The grade control decision is the last decision made in the resource exploitation sequence.

May 1, 2009

By C. D. M. Chisholm

Introduction The Sullivan orebody is a sulphide replacement deposit in beds of argillaceous quartzites. The general strike of the vein is north and south, with rather an abrupt change to northwest in the north limits, and a pronounced steepening of the dip in the same area. An east-west section across the orebody in the vicinity where the change in strike occurs will show the dip-to the east-to be about 10° to 20° above the 4500 level, 20° to 30° between the 4500 and 3900 levels, and 35° to 45° between the 3900 and 3500 levels. It is this last section, averaging 75 feet in thickness, that is being mined by the blast hole method discussed in this paper. Typically, the mineralization throughout this section follows the same general pattern between footwall and hanging-wall, there being solid sulphides for a width of 30 to 50 feet, above which lie quartzite beds of varying widths separated by ore bands which also vary in width and in grade. This banded part of the vein usually extends for 30 to 40 feet above the solid sulphides, with commercial ore terminating on reaching a siltstone bed. Development is generally carried to the highest ore band which, when averaged with the underlying quartzite band, will assay about the marginal limit in lead and zinc. When wide stopes are opened, sloughing to the siltstone usually occurs and, although the values are too low to carry the cost of developing and mining, the caved muck can be handled profitably with only haulage and treatment to be considered.

Jan 1, 1946

By Avi Nanda, Robert Brandt, Alex Piatkiewicz, David M. Jones

In 2010 the United States Environmental Protection Agency (UESPA) revised the National Ambient Air Quality Standards (NAAQS) by lowering the permissible value to a 1-hour average SO2 concentration of 75 ppb. In 2012, the USEPA designated the Miami area as non-attaining for the new SO2 NAAQS. A number of options were studied to assist in bringing the Miami smelter into attainment with the new standard. The chosen solution included: Installation of a large tertiary hooding system over the converter aisle; Hooding of the anode vessels and treatment of the anode gas in a baghouse; Installation of a large 2,325,212 Nm3/hr caustic scrubber to treat the captured converter fugitives and anode off-gases; Installation of a secondary ESP for the tapping fugitive off-gas treatment system; and the continuous scrubbing of all acid plant tail stack gases. The modifications have reduced smelter SO2 emissions by 85%, achieving a world class SO2 stack emissions rate of 0.45 kg of SO2/tonne Cu. INTRODUCTION The Freeport McMoRan Miami smelter has been previously described in literature (Steinborn, Pasca, Sallee, Binegar, Bhappu). For the sake of brevity a brief description is given here. The Miami smelter is located 129 km east of Phoenix, Arizona near the town of Miami, Arizona. The smelter was established in 1915 and has undergone a number of process upgrades and modernizations over the years. The present smelter consists of an Isasmelt furnace, an electric settling furnace, four Hoboken converters, two anode refining vessels & one casting wheel; and one double contact sulfuric acid plant. Concentrates are railed & trucked to Miami from four Freeport McMoRan mines located in Arizona & New Mexico. The wet concentrates, typically containing 10% H2O with a Cu/S ratio of 0.85, are smelted in an Isasmelt furnace to a matte grade of 58%. The entire output from the Isasmelt is laundered into an Elkem electric furnace (originally installed in 1972 as the primary smelting furnace) for separation into matte and slag. Slag containing 0.85% Cu is skimmed from the electric furnace and discarded. Molten matte, containing 60% Cu, is tapped from the electric furnace and processed in one of four Hoboken converters to produce blister copper. Two anode refining vessels further refine the blister copper before the final product is cast on a single, 30 mold, casting wheel. All of the anodes produced at Miami are shipped to the Freeport McMoRan electrolytic refinery in El Paso Texas for refining into cathode copper. Smelter off-gases from the Isasmelt, electric furnace and Hoboken converters are combined and treated in a double contact acid plant to produce sulfuric acid. Acid produced at Miami is internally consumed at Freeport McMoRan mines in the region.

Jan 1, 2019

By J. B. Evans

"NORMALLY the duties of the exploration engineer and geologist cover the initial, and possibly, the most important phase of mining property evaluation; that phase being the presentation of an opinion of the property's ore reserve potential in terms of tonnage and grade. The prime objective of this pa-per is to outline one method of bridging the wide gap that lies between a know ledge of a property' s tonnage and grade potential and an appreciation of the value of that property in dollars and cents.THE PRESENTATION OF PROPERTY EVALUATIONThe engineer engaged on a mining property evaluation, regardless of whether he be an independent consultant, or a company employee, has as his goal, the presentation of his appreciation of the property's potential value or worth within terms of reference acceptable to his principal.To furnish a complete evaluation report, the evaluator must firstly study all aspects pertaining to the particular property under consideration, then present his appreciation of the property's worth in some tangible form. The ultimate presentation is one giving a Present Value of the pro pert y in terms of monetary exchange. Such an idealistic presentation is not always possible; typical preventives being -insufficient reliable information, limited time, Jack of ability and absence of definite direction."

Jan 1, 1960

By A. J. Goodman

Introduction The position of Turner Valley in the foothills of Alberta, some thirty-five miles southwest of Calgary, is too well known to need further description. This attempt to interpret in detail the nature of the structure, and its relationship to neighbouring structures, together with general observations on the foothills belt, is based on work carried out in the office of the Supervisory Mining Engineer, at Calgary. The object in view was the correlation of the mass of evidence which had accumulated from the detailed examination of drill cuttings, and to discover, if possible, its structural significance. Unfortunately it is not possible to publish most of this detail owing to its confidential nature, and in consequence the reader is asked to accept certain statements, which under other circumstances would not be made without supporting evidence. The main argument for the general structural interpretation rests on evidence which has already been made public, and it is possible to proceed to logical conclusions on the main points. The evolution of ideas concerning the structure of Turner Valley is somewhat difficult to follow, as, compared with all that has been said on the subject, there is not a great deal on record.

Jan 1, 1930

By S. Demetrio

China has a traditional segment of Copper Smelters with its own Chinese technology, typically small in size from 20.000 to 50.000 tCu/a, and they are responsible for the processing and production of more than 600,000 tonnes of blister copper per year. For occidental experts, like one of the authors, it is not so easy to believe that they are profitable, because the size and the use of old Blast Furnaces, but they are with simple and effective production lines. The authors are convinced that China has a good alternative to improve theses old copper production lines with small innovative changes in its process arrangement, jumping to higher level technology, more efficient in production, productivity and cost, assuring copper as a raw material for the country and its high speed development. The key to improve that the traditional Chinese Copper Smelter is white metal as an extra raw material as a first step doubling the copper production from raw materials and the complete replacement of concentrates by white metal (WM) in a second step increasing it four times or more as the final goal. It is not so difficult nor expensive to make it happen, but there are a couple of questions for implementing this innovation in the copper smelter industry: 1 - Will the old fashioned mentality be open to this new direction for China being the biggest copper consumer on one side, and the biggest copper Primary Producers on the other hand? and 2 - Will they be open to follow this "win-win" strategic way for both ends of the copper market? We don't know if anybody will take up the challenge to improve it but our responsibility as a consulting expert and a university professor is to put the alternative on table for others to decide whether to implement it.

Jan 1, 2007

By K. Nikkhah, N. Dhadli, G. Freeman

Ammoniacal pressure leaching operations have been in commercial use at the Fort Saskatchewan refinery of Sherritt International Corporation since 1954. Recent improvements have significantly increased the capacity of this circuit. The computer modeling of this process has proved to be a valuable tool in facilitating the evaluation of different operating scenarios in an effective manner. Reagent response in the ammonia leach of nickel and cobalt sulphides is examined using the dynamic process simulation capabilities of IDEAS(TM) software. The dynamic simulation enables accurate measurement of the sensitivity of the process to variables such as temperature, feed rate and ammonia concentration as well as compartmental analysis of metals concentration, pulp density, vent gas composition, and the formation of specific complexes. The complexity of the ammonia leach process makes it a logical choice for evaluation by computational analysis. The methodology for dynamic modeling of a pressure leach process is presented.

Jan 1, 2005

By BARRY BANNATYNE

Non-swelling bentonite has been quarried in Manitoba by Pembina Mountain Clays Limited since 1941. It occurs in several thin layers near the base of the Pembina Member of the Upper Cretaceous Vermilion River Formation, and is quarried from the narrow outcrop belt along the slope of the Manitoba Escarpment. It is marketed both as natural and activated bentonite for a variety of specialized uses. Percolation of acidic water through bentonite has produced a naturally activated bentonite with good absorbent properties; these properties are enhanced by treatment with sulphuric acid to produce an activated bentonitefor decolourizing petroleum and vegetable oil.

Jan 1, 1984

By Cy Jordan, Ben Burdett, Adrian Dance, Jack Rainey

"In 1997, EIMCO Minerals installed a knowledge-based control system on one of the five primary grinding lines at Highland Valley Copper. The objective of the system is to maximise throughput without affecting circuit product size or flotation recovery. The system was commissioned in October 1997 on a SAG mill/ball mill circuit following a plant audit and upgrade of the control instrumentation.The system monitors and controls the SAG mill power, bearing pressure and recycle load by manipulating the solids feedrate, water addition and mill speed. The two ball mill and cyclone circuits are controlled through water addition at various points in the circuit as well as the number of operating cyclones.An on-line particle size analyser is used to measure the cyclone overflow quality. Models of the SAG mill charge level and overflow product size are also incorporated. A method of predicting the SAG mill power response to feedrate changes is used to lessen the effect of dead time for improved mill power control. In the future, inferred measurements of SAG feed particle size and hardness will allow changes in ore behaviour to be predicted and compensated for by the system.This paper describes the development of the project -from installation and commissioning to modifications and refinement -along with prospects for the future.BackgroundIn early 1997, EIMCO Minerals was contracted by Highland Valley Copper to install a knowledge-based or expert system control strategy on one of the five grinding lines in the mill. This was to become the start of the Advanced Control Project at Highland Valley Copper (HVC). This paper will review the progress of the Project as well as discuss the prospects for the future.Following a preliminary engineering study (or plant audit) by EIMCO in 1996, it was decided to implement an advanced control system in order to improve plant operations and increase productivity. The study suggested that such a system had a pay-back period of a few months through increased throughput without loss in flotation recovery. Highland Valley already had successfully applied higher level control through their Elsag Bailey distributed control system (DCS) and this was the next stage in process optimisation."

Jan 1, 1998

By C. Pichler, J. Antrekowitsch

During the production process of steel and other metals a lot of different by products are generated in high amounts. Some of these residues are recycled to recover valuable metals like zinc, lead, copper and others. Especially the treatment of steel mill dust presents a great challenge. The need for new technologies can be seen in the wide range of available recycling concepts for steel mill dust treatment, however most of them have significant disadvantages. An example is the waelz process, which generates about 650 to 700 kg slag during the treatment of 1000 kg steel mill dust. This so called "waelz slag" must be dumped in the most cases. To avoid a landfilling all generated products must be able to get reused in another application. A so called "Zero Waste Process" can be reached with the "2SDR Process" (Two Step Dust Recycling Process), in which the dust is treated on an liquid iron bath generating cast iron, inert slag and zinc oxide. These products have a further usage and can also be sold. The paper focuses on the process development through trials in lab and technical scale up to planned pilot scales, with an accompanying characterisation of the generated products were done.

Jan 1, 2014

By Forrest A. Kerr

Introduction During recent years the work of the Geological Survey in northwestern British Columbia has been in the nature of reconnaissance and exploratory mapping, largely for the purpose of gaining knowledge of the potential mineral-producing zones known to occur along the eastern side of the Coast range, and also to gather such data as might facilitate their exploitation. Commencing with fairly detailed mapping in the more accessible parts, the work has been continued and expanded until now an understanding has been gained of the more general features of a continuous section along the range for a distance of about two hundred miles. Geographically, northern British Columbia is more or less isolated. It is cut off from the central part of the Province by a rugged and mountainous country which, except for the telegraph line and a rarely travelled trail along it, is not penetrated by any developed routes or lines of communication. To the west, it is cut off from the Pacific by the Coast range, an extremely rugged area sixty to eighty miles in width which, except along the few navigable rivers cutting across it, cannot be readily traversed. Politically, it is further isolated in this direction by the narrow strip of south-eastern Alaska which borders the coast and extends inland to the axis of the range.

Jan 1, 1931

By J. Spross

"The Key Lake mill has operated since the fall of 1983. The ore from both Key Lake open pits will be depleted by 1997. It is planned to use this mill, located about 60 km southwest of McArthur, to process the McArthur River ore.While the geological data collected so far on the McArthur deposit are encouraging, more information of the deposit is needed before any detailed mine planning can begin.The surface drilling program identified the orebody and provided information on the geomechanical and hydrological properties of the overlying sandstone. It was proposed to conduct an underground exploration program to further delineate the orebody. This was air proved following a public hearing and review process. This program involves the sinking of a 630 metre deep shaft and the driving of one or two drifts along a portion of the orebody. From these drifts, exploration drilling every 10 m to 15 m through the orebody will provide the information required for the preparation of a feasibility study and an Environmental Impact Statement (EIS)."

Jan 1, 1994

By Klau Meyer

"At Teck-Corona Operating Corporation's David Bell Mine, a successful water quality management strategy has been established. This resulted from the development and application of process technology, allowing year round discharge of an effluent exceeding the chemical and biological standards set by the Ministry of Environment. This strategy aims at minimizing contaminant levels of effluents through optimization of reagent selection and reduction of effluent volumes through maximizing reclaim water usage. Concentrator and effluent treatment plant operating practices, process chemistry and the results of the water quality management strategy are reviewed.IntroductionThe David Bell Mine is located in the Hemlo gold camp 42 km east of Marathon, Ontario. The concentrator has a design throughput of 1000 tonnes per day. The processing of the run of mine ore ( - 15cm) involves the following unit operations: grinding in a semi-autogenous mill followed by a ball mill, thickening, pre-oxidation , cyanidation, and carbon-in-pulp gold recovery followed by electrowinning and refining.The David Bell Mine water quality management strategy is composed of the following items (Goodfellow and Meyer, 1991):• natural destruction of cyanide contained in the tailing water in a large shallow tailing pond ;• preliminary treatment of reclaim water in the grinding circuit for cyanide and heavy metal removal;• pre-oxidation of sulphide minerals in pipe reactors to reduce cyanide consumption using pure oxygen;• pH control in the grinding, pre-aeration and leach circuits to minimize the dissolution of stibnite while maximizing gold recovery; • close control of cyanide addition rates to the leach circuit to maintain the lowest possible levels;• a carbon column for gold recovery;• an effluent treatment plant for antimony and heavy metal removal; and• the use of final treated effluent for industrial water underground to minimize fresh water consumption."

Jan 1, 1992

By David Rahal, Saul Ortiz, Maria Escobedo

The general trend in the minerals industry is towards the processing of fine grained, disseminated mineral deposits. This has led to an increase in the number of fine/ultra-fine grinding installations using stirred media mills. The challenge is that both the equipment type and the mineralogy of the deposit have an effect on specific energy consumption. Fresnillo PLC recognized this issue and addressed it by providing samples for testing in a laboratory regrind system. The objective of the test program was to determine the specific energy required to achieve a product size of 10 µm (P80). A specific energy plot was generated for both a lead and zinc flotation concentrate. It indicated that 34 kWh/t and 51 kWh/t were required for the two samples (Pb and Zn respectively). This difference highlights the effect of mineralogy on the energy required for fine grinding. The regrind feed and products were submitted to a range of basic mineralogy tests to quantify the mineral differences that could have changed the specific energy requirements. These tests provided general mineralogy, documented optical textures, and provided particle size microscopy. The lead concentrate was found to contain significant amounts of silicates in addition to the dominant sulphide, pyrite. The zinc concentrate was determined to be mostly sphalerite with minor amounts of quartz, chalcopyrite, pyrite and galena. The material testing results illustrate the importance of basic mineralogy studies in conjunction with comminution testing to determine specific energy consumption.

Jan 1, 2016

By F. G. Smith

Abstract Laboratory methods are now in use whereby the temperature and pressure during the crystallization of hydrothermal minerals can be determined. The techniques include the use of the decrepitation method of studying liquid inclusions, and electrical measurements of pyrite. The determinations are sufficiently accurate that the data can be used in solving a variety of ore deposition problems. Within the last year, several new laboratory techniques have been developed in the Geochemical Laboratory of the Department of Geological Sciences, University of Toronto. The results of several tests of ore by these methods have proved to be useful in treating some problems which previously were considered unsolvable. It is now possible to determine the temperature of deposition of most of the minerals in a hydrothermal ore deposit, also the depth below the surface during deposition. Measurements can also be made of the reopening history of a complex ore. The temperature-pressure determinations depend upon the fact that minerals deposited from a hydrothermal solution always trap a small amount of the solution at the time of crystallization. The solution, being predominantly composed of water, has a density which depends upon the temperature and the pressure prevailing during crystallization. After ore deposition is complete, erosion and isostatic uplift finally exhumes the vein. During this slow fall in temperature and pressure, the solution contracts and a gas bubble appears. If the trapped solution in the mineral is examined, the gas-liquid ratio records the density of the solution at the time the mineral was deposited (except for a slight change in the volume of the mineral). The thermal expansion and compressibility of water and water solutions are known to a sufficient degree that, if the gas /liquid ratio can be determined, the temperature-pressure relations during deposition can be calculated.

Jan 1, 1949

By J. Groppo, W. Zhang, R. Honaker

"The flotation of monazite is depressed when using hydroxamic acid as a collector in the presence of calcium ions which may exist due to the dissolution of minerals such as calcite. Minor dosages of sodium hexametaphosphate (SHMP) were found to effectively depress calcite, whereas the flotation of monazite was not impaired in single mineral flotation tests. However, in a mixed mineral flotation system, monazite flotation was depressed significantly. The mechanism of hydroxamate adsorption on monazite and calcite, the depression mechanism of calcite on monazite, as well as the depression mechanism of SHMP on calcite and monazite were studied using micro-flotation, electro-kinetic, and adsorption tests. Findings indicate that the adsorption of hydroxamate on monazite was due to chemisorption while adsorption on calcite was a result of physical interaction. SHMP significantly increased the negative charges of calcite surfaces which depressed the adsorption of the hydroxamate anions on the calcite surfaces due to an elevated electrostatic repulsion force. When calcium-rich minerals such as calcite are mixed with monazite, the calcium ions dissolved from the mineral surfaces specifically adsorb onto the phosphate oxygen sites on the monazite mineral surfaces thereby causing depressing effects. The addition of SHMP to suppress collector adsorption on the calcite surfaces interacts with the calcium species that were specifically adsorbed onto the monazite surface, which prevents hydroxamic acid adsorption onto the rare earth oxygen sites due steric hindrance and results in the flotation depression of monazite. INTRODUCTIONAs one of the commercial rare earth ores, monazite has been widely exploited to produce additives for catalysts, batteries, alloys, etc. Because of the complexity and the fine nature of some monazite ores, methods such as gravity, magnetic, and electrostatic separation to treat beach sand monazite fail to produce satisfactory concentrates, suggesting the use of floatation is warranted (Cheng, Holtham, & Tran, 1993). The primary associated minerals of monazite ores include ilmenite, quartz, zircon, rutile, sillimanite (Dixit & Biswas, 1969; Pavez a& Peres, 1994, 1993). Using sodium oleate as collector for monazite has been reported in many studies (Cheng et al., 1993; Dixit & Biswas, 1969; Pavez & Peres, 1994, 1993). Several investigations have reported maximum floatability of monazite occurring at pH values between 8 and 9 (Cheng et al., 1993; Dixit & Biswas, 1969). A study conducted by Pavez and Peres (1994) compared the use of hydroxamate and sodium oleate for the treatment of a monazite ore and found that hydroxamate significantly improved the grade of rougher concentrate."

Jan 1, 2016

By Franco Oboni

Numerous voices are raising around the world to show how misleading and fuzzy commonly used risk assessments methods are. These criticisms come at a time when public trust in ?proponents of new projects?, operators, private or governmental, seems to have hit a low and the legal system ?targets? public officers. It is common that technical experts and the public strongly disagree in their analysis of risks. Risk definition requires the evaluation of probability and consequences and those words are oftentimes enough to stir great worry to the public. Thus it is nowadays commonly understood that ?reality? is not scientific, but resides in public opinion, hence urging technical people to communicate better, more transparently. Blatant failures on both counts have lead to the emergence of ?new myths? used to justify complacency using ?complexity? and other buzz words as an alibi. This paper (together with its companion presented elsewhere) explores how poor ?common practices? in Risk Assessment contribute to biasing project team, design teams opinions, skew decision-making process and finally misrepresent reality to the public resulting precisely in the raise of public distrust, legal implication witnessed around the world. The discussion first reviews the pitfalls of common approaches (FMEA, Probability Impact Graphs) pinpointing them as possible causes of future legal liabilities. An alarming disconnect also comes from various codes, ISO 31000 itself has this flaw, invoking the term ?acceptable?/?tolerable? without defining it or giving any guidance for its determination. Wide-spectrum public consultation could be developed to define a ?modern? social acceptability criteria helping all the stakeholders making/understanding decisions. Another alarming disconnect comes from the poor definition of consequences of mishaps and their societal ripple effects. This aspect is indeed mostly ignored in codes, leaving ample room to biases and censoring applied to potential losses. In our society no one seems to have anymore the possibility of hiding behind a shroud of ?carefully maintained? misrepresentation. It is time to act and ?write the book? for proper risk assessments avoiding misrepresentations.

May 1, 2013

By Prodipto Ghosh

This paper is prepared as a review of existing and traditional methods related to electrical maintenance strategy. Its primary focus is to explore newer ideas and how they point the way to a more efficient and effective manner of electrical maintenance. This discussion is primarily related to large electrical distribution assets typical of heavy industry such as mining.

Aug 1, 2013