Search Documents

By Dwayne D. Tannant

The Fox Pit at EKATI Diamond Mine reached a depth of approximately 150 m as of September 2005. The pit is designed with 11 m wide benches excavated using a double benching technique leaving 30 m high bench faces. A series of blasting tests were conducted to improve catch bench reliability and increase the percentage of benches that meet an 11 m catch width. The design changes focussed on reducing damage to the bench crest because maintaining the bench crests is the most important factor in achieving good bench reliability. The most significant improvement was obtained by raising the bottoms of the lower trim blastholes by 0.5 m. This change decreases the depth of broken rock below the final bench elevation, and consequently reduces damage to rock that forms the bench crest below. Another improvement was the use of smaller diameter (165 mm vs. 270 mm) blastholes in the A and B rows for the upper trim blast. This change reduces the charge per delay during detonation, reduces the powder factor slightly, and reduces the energy affecting the final pit wall and crest. As mining and the blast testing progressed, the portion of the bench with crest achievements (>11 m) increased from 57% to 75%.

May 1, 2006

By Douglas A. Karvonen

"Competition in the world potash market has increased significantly since the late 1970s. The failure of consumption to grow at expected levels has led to industry over-capacity, a situation which is likely to persist at least until 1990. Individual Saskatchewan producers and their offshore marketing company, Canpotex, have responded to this challenge by increasing mining efficiency, developing more cost-effective and reliable transportation systems and establishing innovative financing and market development programs tailored to customers' special needs. Investment in warehouse facilities to serve U.S. customers and exploration of opportunities for intermodal distribution through the Great Lakes and the Mississippi River system have maintained individual producers' position in the highly competitive domestic market.Export sales through Canpotex have been bolstered by utilization of CIDA funds, Exp ort Development Corporation financing guarantees and other innovative payment plans which enable heavily indebted developing countries to maintain the import levels which are necessary for their agricultural development.IntroductionPotash is the general term applied to various potassium salts both natural occurring and commercially derived. The most common of the commercial product s are potassium chloride, potassium sulphate and potassium magnesium sulphate. The potassium content of potash is measured in units of K20 equivalent. The common grades of potassium chloride produced for agriculture average at least 60 0/0 K20 compared with approximately 50% Kp for potassium sulphate and 22% for potassium magnesium sulphate."

Jan 1, 1985

By Frank Martonhegyi

"The objective of this paper is to review the coal basins in the Canadian part of the Western Cordillera to aid their understanding, and to aid in finding and proving places of economic coal mining potential. Coal occurs in eugeosynclinal basins in the Western Cordillera which evolved through three stages: -from systems of volcanic arcs in the Late Jurassic to mid-Cretaceous; -through an intermediate stage with deposition in increasingly restricted successor basins in Jurassic to Early Tertiary; -to a continental stage by the Eocene. Minor coal seams occur usually in late volcanic arc stage sediments bur they can be locally thick as they are on Queen Charlotte Islands. Successor basins usually show a marine-paralic-limnic evolurion. Signijicanr coal deposits occur in the tarter two sequences in the Whirehorse (Tantalus) and Bowser (SkeenaSusrur) basins. Currenr activities are intensive in the more accessible Bowser Basin, for example at Telkwa, Susrut River and on the Groundhog coal field. On Vancouver Island major coal seams occur in cyclic sediments, but the more accessible deposits are mined our. Exploration renewed recently in the less accessible northern part of the Island, for example Quinsam, for surface mineable coal. The Western Cordillera is a mosaic of allochtonous tectonic blocks. They originated from the south and were displaced northward by several hundred kilometres. Many Tertiary coal basins are related to strikeslip transcurrent faults along which the later part of displacement took place, for example the Dawson coal area in the Tintina Trench. Tensional and dipslip normal faulting also created or enhanced sites for thick peat accumulation. For example at Hat Creek 280 m of coal occur in a 550 m section. Secondary structures are often better exploration targets than the main fault zones. Pluvial and alluvial fan environments away from the main drainage are usually the favourable sites for thicker and cleaner coal deposition."

Jan 1, 1985

By Y. Prevost, D. Verhelst

"A computer-assisted process control system for the Noranda Process Reactor Wa5 installed at the Home smelter in 1991. Operating as an advisory tool for the furnace operators, and using a flexible oxygen balance as the basic building block of the computer program, the new control system has helped to reduce the variability in the grade of the matte produced by 50% . The smelter is currently operating at a 72% copper matte, with a standard deviation of between 1.0 and 1.3, while treating a wide range of concentrates, secondary materials and scrap. Enhanced process control has allowed for longer reactor campaigns, and improved stability of the converting operation.This paper reviews the feed classification and blending practice used at the smelter, outlines the strategy of the new computer control system, and summarizes the benefits realized since the implementation of the system in early 1990.IntroductionUntil 1989 the Noranda Home smelter operated as a multi furnace smelter, at one time having three hot-charge reverberatory furnaces, and finally operating with one wet-charge reverberatory furnace and one Noranda Process Reactor. In 1989 the final reverberatory furnace was closed and the Reactor became the sole smelting vessel, treating around 750 000 tonnes of concentrate, secondary materials, and scrap per year. At the time of the start-up of theNoranda Reactor in 1973, the vessel was capable of treating 750tonnes per day of a heterogeneous mixture of copper concentrates, fluxes and secondary materials to produce copper in one operation. Through process improvements, and the introduction of additional oxygen in 1982(pannell and Mackey, 1988), the daily tonnage increased to 1800 tonnes by 1988. The operation had also been changed to produce a high-grade matte instead of copper. Figure1 illustrates the main features of the reactor, a cylindrical vessel which is charged at one end and tapped at the other. The matteis subsequently processed through Peirce-Smith converters and anode furnaces before being cast into copper anodes. Figure 2 outlines the progressive increase in the furnace smelting capacity. Over this period the percentage of secondary materials, and scrap feeds also increased to approximately 110 000 tonnes per year, or 15% of the total new feed input (Bedard et al., 1991). Now operating wholly as a custom feed operation, the Home smelter can treat over 2200tonnes per day of new metal-bearing material."

Jan 1, 1993

By P. A. Riveros

The literature on the arsenic disposal practices of the metallurgical industry and the long term stability of the disposed arsenic compounds were reviewed from a Canadian perspective. The review was complemented with visits to selected operating metallurgical sites to obtain information on their specific arsenic disposal practices and the behaviour of their impounded residues. The arsenic disposal procedure currently favoured by the industry involves the formation of an insoluble ferric arsenate compound which is allowed to sediment at the bottom of tailings or residue ponds. It has been shown recently that this poorly formed crystalline compound is similar to ?arsenical ferrihydrite? which is ferrihydrite containing strongly adsorbed arsenate anions. Despite concerns about its long term stability on thermodynamic grounds, arsenical ferrihydrite appears to be stable for many years in the proper environment which includes a slightly acidic pH and oxidizing conditions. A high Fe/As ratio and the presence of heavy metals appear to increase the stability of arsenical ferrihydrite. High temperature operations, such as those encountered in the autoclave treatment of refractory gold ores, are conducive to the formation of scorodite, FeAsO42H2O, and/or a series of ferric arseno-hydroxy-sulphate compounds depending on the solution composition. Scorodite has several advantages over arsenical ferrihydrite as a disposal compound including a lower iron demand, a higher density and a greater thermodynamic stability. New procedures have been developed to generate scorodite at ambient pressure. These procedures would offer significant reductions in capital cost because of the elimination of the need for autoclaves. Lime precipitation which was widely used in the past is being abandoned as a result of strong evidence showing that calcium arsenate compounds decompose slowly in contact with atmospheric CO2 to form calcium carbonate and soluble arsenic acid. In all cases, the long term stability of the disposed arsenic compounds depends on a number of factors including disposal site characteristics, particle crystallinity and size distribution, the presence of complexing agents and the effect of bacterial activity.

May 1, 2002

By Jacob Wood, Robert Matusewicz

The Outotec® Ausmelt Top Submerged Lance (TSL) Process has achieved widespread commercial acceptance over the past 40 years for the processing of copper, nickel, lead, tin, zinc and precious metal bearing feeds. The continual development and evolution of the technology during this period has resulted in a more intense smelting process with higher energy efficiency and lower operating costs. More recently, considerable effort has been invested in decarbonisation of the process through improvements such as increased oxygen usage, dry feed injection and use of low-carbon auxiliary fuels. This paper covers a number of these recent advances to the technology and highlights their impacts on energy consumption and CO2 emissions for a range of non-ferrous smelting flowsheets. INTRODUCTION Relentless demand for improvements in the profitability, safety and environmental performance of non-ferrous smelting plants has driven a continual development and evolution of processing technologies in this industry. In response to these demands, a number of bath smelting technologies have emerged over the past 40 years and have been implemented for the treatment of primary and secondary feedstocks. The Outotec® Ausmelt Top Submerged Lance (TSL) Process (henceforth Ausmelt Process) is one such bath smelting technology which has been widely adopted in a large number of greenfield projects and brownfield plant modernisations (Wood & Hughes, 2016). Emissions of CO2 from the production of non-ferrous metals represent approximately 4-5% of global totals (Rankin, 2012), comparable with the almost 10% attributed to iron and steel production. Despite significant improvements in the energy efficiency of modern smelting technologies (Coursol, Mackey, Kapusta & Cardona Valencia, 2015), primarily through increased oxygen usage, further innovation and development is still required to address their reliance on fossil fuels such as coke and coal. Transformation of the non-ferrous smelting industry to low-carbon technologies and process flowsheets is lagging behind the power and transport sectors, which have witnessed significant growth in clean/renewable energy technologies to reduce CO2 emissions and address the issue of anthropogenic climate change (IRENA, 2018; IEA, 2018).

Jan 1, 2019

By Hans Lundberg

The magnetometer which was developed during the war for detecting submarines has proven exceedingly valuable in outlining deep-seated structures in oil exploration, and will be useful also to geologists in outlining regional structural features in the Precambrian. Our magnetometer has been developed to outline local and detail structures. 1 am quite sure that all geophysicists and geologists would agree with me that, in ore prospecting, it is important to obtain as much detailed information as possible. We know that, as we ascend from the ground and get away from the magnetic ore-bearing structures and orebodies, the magnetic intensity decreases rapidly, but, worse than that, we lose the details even faster. Figure l shows two strong, very sharp, magnetic 'highs' over two orebodies which, as our distance increases, rapidly merge into one fairly broad, moderately strong anomaly. If we drilled on this maximum, we would not encounter any of the orebodies. Therefore, we should fly the airborne magnetometer as close to the ground as possible in order to duplicate the results of the magnetic ground surveys. The first chance to accomplish this came with the helicopter, which is an exceedingly maneuverable aircraft. It can be landed in a cleared space not much more than fifty feet square. With floats, it can be landed anywhere, even in a swamp, on thin ice, or on soft snow. It can stand still in the air, hovering over a given point. It can ascend and descend vertically, fly sideways and even backwards, at the will of the pilot. It flies forward at any speed up to l00 miles an hour. The helicopter can be taken to any desired position at a given time. It can fly at any useful altitude from a few feet to several thousand feet above the ground. It can fly very close to the ground with safety. In bare areas, the survey flight may be performed a few feet above the ground. In forested areas, however, the flights, to clear the trees, must be made at l00 to 150 feet. To mark out a certain point, a small parachute-like marker may be draped over a tree or laid on the ground. This can be done from the helicopter without touching the ground.

Jan 1, 1947

By D. McFadgen

"THE Dominion Steel & Coal Corporation, through its subsidiaries, the Old Sydney Collieries and the Dominion Coal Company Limited, produces 4% million tons of coal annually from eight submarine collieries situated on the eastern coast of Cape Breton Island. The present workings have a frontage of 20 miles and extend 31/2 miles under the Atlantic ocean on gradients varying from 4 deg. to 24 deg. To date, some of the workings have reached .a depth of cover up to 2,800 feet.The pitching seams, the annual seaward advance, the resulting depth of cover and the rdatively soft roof and floor have necessitated the adoption of extensive longwall mining, with room-and-pillar mining con-fined to areas above the 1,000 foot cover line, where 60 per cent of the -coal is left standing in pillars to support the ocean floor. Longwall mining accounts for 87 per cent of the total production with the remaining outputs obtained from room-and-pillar work and the narrow work development. Seventy-four per cent of the longwall production and 41 per -cent of the room and development production is completely mechanized.Although 2 tons of water is pumped from the collieries for each ton of coal mined, the working sections are relatively dry as the heavy make of water is essentially surface drain-age from the land crop areas. The dry workings and the long haulage distances, which in many cases exceed 4 miles, have resulted in a continuing programme to combat the dust hazard, both at the working face and along the mine roadways."

Jan 1, 1960

By A. J. DeArdo

Linepipe steels have come a long way in the past forty years. In fact, modern, high strength steels for large diameter linepipe applications represent one of the seminal accomplishments in metallurgy of the past half-century. The synergy of advanced steelmaking, alloy design including microalloying, hot rolling, and interrupted accelerated cooling has led to the marvelous steels being used today. The drive for higher performance pipelines has been motivated by the energy sector of our global economy who wanted both higher throughput capacity, i.e., larger diameters and higher pressures, and lower material cost, i.e., relatively thinner gauge wall thicknesses. These requirements led to new steels with higher strengths, better toughness and improved weldability. The goal of this paper is to trace the evolution of linepipe steels from the X60 grades of the small diameter pipelines of the 1960s to the (X80 - X120) grades used in the large diameter pipelines of today. The metallurgical triumphs permitting this success story, e.g., clean steel practices, controlled rolling, microalloying with Nb, and using IAC to obtain low temperature transformation products, will be highlighted and discussed.

Jan 1, 2005

By R. F. Engler

"IntroductionThe Coal Branch region of west-central Alberta has been the focal point for unprecedented exploration and development activities over the past ten years prompted by the renewed markets for high-quality thermal coal. Although mines were developed and operated extensively throughout the region from 1910 until 1960, information relating to the detailed stratigraphy of the coal measures and their areal distribution tended to be localized to individual mine sites. Continuity along trend was impaired by a paucity of outcrop restricting geologic mapping to stream bank and roadside exposures. Recent studies and subsequent publications by Jerzykiewicz and McLean of the Geological Survey of Canada (1978, 1980) have established a detailed sedimentological model and defined the stratigraphic nomenclature for the region . The term Coalspur Beds has been adopted to describe the coal-bearing sequence between the overlying Paskapoo Formation and underlying Brazeau Formation. Complete sections of the Coalspur Beds have been compiled from sub-surface borehole data and published by Manalta Coal Ltd ., Dentherm Resources Ltd. and Luscar Stereo Ltd. This paper is an attempt to correlate this information on a regional basis to illustrate trends within the Coalspur Beds."

Jan 1, 1986

By Z. Zhong, Y. J. Hu, D. Elsworth

"A standard triaxial apparatus was set up to perform sliding tests. Slide-hold-slide (SHS) tests, with hold times from 10 to 3000s and at invariant effective confining pressures of 1MPa, incremented to 3MPa and then 5MPa, were conducted on both dry and wet split limestone samples to study the evolution of fracture friction under holding and sliding processes. Limestone fracture shows time-dependent behaviors in SHS tests, friction drops (creep) gradually during hold periods, and recovers (healing) after re-slide. Frictional healing and creep increment are proportional with hold times, while are inversely proportional with effective confining pressures. Moreover, the wet sample displays heavier healing than the dry one, whereas creep increment of the wet sample is lighter than the dry one. We conclude that the evolution of limestone fracture friction is significantly controlled by mechanisms of fluid-rock interactions.INTRODUCTIONThe evolution of the mechanical properties of fractures and faults exerts a critical influence on the behavior of fault zones and on the earthquake cycle. In addition to natural processes, this behavior has broad implications in induced seismicity and influences oil and gas production, the sequestration of carbon dioxide and the disposal of nuclear wastes.Fault friction is typically measured by slide-hold-slide experiments, where fault gouge is deformed at low velocities (<0.1 mms-1) and over small shear offsets (<30 mm) (Dieterich, 1979, 1981; Mair et al., 1999; Marone, 1998, 2004) or alternatively with rotary-shear devices, that enable higher slip velocities over very large shear offsets (Hirose & Shimamoto, 2005; Mizoguchi et al., 2006). Typical experiments (Dieterich, 1972; Marone, 1998; Olsen et al., 1998; Bos & Spiers, 2002; Tenthorey et al., 2003) show significant creep during the holding period and frictional healing (strength gain) upon reloading. Fault creep and healing are often time-dependent with longer hold times typically resulting in greater magnitudes of creep and in strength gains (Tenthorey et al., 2003; Yasuhara et al., 2005; Carpenter et al., 2012). Frictional healing may arise from growth of grain contacts (potentially induced by pressure solution) (Rabinowicz, 1951; Dieterich & Kilgore, 1994; Yasuhara et al., 2005), strengthening of the contacts (correlates with cementation) (Hickman & Evans, 1992; Beeler et al., 1994; Karner et al., 1997; Olsen et al., 1998; Muhuri et al., 2003; Tenthorey et al., 2003; Li et al., 2011) or via other changes in state including changes in porosity and rearrangement of force chains. Experimental evidence (Dieterich, 1979, 1981; Johnson, 1981; Marone & Scholz, 1988; Marone, 1998; Saffer & Marone, 2003; Moore & Lockner, 2007; Ikari et al., 2007; Ikari et al., 2011; Carpenter et al., 2012) quantifies both the mode and magnitude of second-order changes in the velocity-dependent (including velocity- strengthening and weakening) evolution of frictional strength."

Jan 1, 2015

By F. E. Lee

The following outline gives a brief account of some of the ways in which microscopy is applied to the problems arising from the various operations of the Tadanac reduction works, at Trail, B. C. The Sullivan ore is a very fine-grained mixture of galena, marmatite, pyrite and pyrrhotite. The separation of minerals associated so intimately is a difficult task and requires careful control. Various oils and reagents are used in the process as developed, and it is essential that the operators have a means of control which shall be rapid, and at the same time, approximately correct. This result is obtained by microscopic analysis in the following manner: The operator places a quantity of the material upon a slide, a drop of water is added, and it is covered with a cover glass. Upon examination with transmitted light, the zinc mineral particles appear reddish, the ordinary gangue colorless, the lead and iron sulphides opaque. This method has proved of great assistance both in the development and in the operation of the present method for concentrating Sullivan ore. The miscroscope has thus become as much a part of the metallurgical equipment as the balance and burette. The microscope used in the laboratory is a Fuess "petrographic" with a specially-made vertical "illuminator" by Bausch & Lomb, with the usual accessories.

Jan 1, 1924

By Godfrey W. McDonald, Dennis E. Fredrickson

"Commercial coal mining has been recorded in Nova Scotia since 1863 and during this period an estimated 60,000,000 short tons of mine discard containing 10 1030% coal has been accumulated, Approximately 70% of these dumps are in the Cape Breton region and most are owned by the Cape Breton Development Corporation (CBDC), formerly DEVCO.The explosion of oil produced energy costs which created an increase in thermal coal demand as well as the desire to rehabilitate abandoned mine dumps encouraged coal reclamation. CBDC was receptive to a proposal from the Selminco Joint Venture and encouraged the building of the Princess Recovery Plant (1980) and The Summit Plant (1982).The mine dump contains scrap, waste rocks, coal and substantial quantities of fine shale. The scrap and oversize are removed and the remaining material slurried with water to a density of 1.45. The slurry is cycloned to separate the saleable thermal coal from the rejects which are returned to designated areas of the dump for contouring and revegetation.BackgroundThe recorded coal production in Nova Scotia from 1863 to 1980 was 390,000,000 short tons. This extraction was associated with an estimated 60,000,000 short tons of discarded material. This mining discard and coal washing plant reject are located in numerous, varying sized dumps throughout the mining areas. Approximately 70% of these dumps are in the Sydney coal field region of Nova Scotia. The coal content of these dumps varies from 10 to 30% coal with an average of 18%.Energy CostsThe explosion o f energy costs in the mid-1970s greatly increased the sale price of thermal coal which made recovery of coal from some of the dumps economical. The environmental benefit of these operations will be the rehabilitation of the dumps upon cessation of the coal reclamation operation."

Jan 1, 1983

By A. J. A. Janse

The Argyle diamond mine is located in the Kimberley region in the northern part of Western Australia at approximately 16°43&apos;S, 128°23&apos;E in subtropical bush/shrub savannah. The 46 ha (113 acres) pipe is situated in the Halls Creek mobile zone, which was cratonized about 1800 Ma ago and adjoins the Kimberley Block, a plateau upheld by Early to Middle Proterozoic rocks underlain by presumably Archean basement. The crater and upper pipe zones of the diatreme have been preserved within tilted and faulted strata of Middle to Late Proterozoic age. Its age of intrusion is about 1178 Ma. The diatreme rock is not kimberlite but olivine lamproite which was not recognized as a primary diamond host rock until 1978. The Kalumburu Joint Venture, a syndicate of local and overseas mining companies, started in 1972 to prospect the Kimberley Block with a modest annual prospecting budget of $125,000. Annual expenditure doubled each year and reached $1 million in 1975 after which CRA took over management of the newly-formed Ashton Joint Venture with an annual expenditure of $2 million (all figures are in current US dollars). The Argyle diatreme was found near the end of the eighth field season and after a total expenditure of $12 million. Annual production is about 34 million carats which places Australia as the world&apos;s number one diamond-producing country, although, because of the low value per carat, it is number four in terms of total annual value. The global cost required for a major diamond mine is between $300 and $400 million, with a discovery every 10 to 12 years. Because Canada contains large areas of prospective platform rocks underlain by Archean basement it is likely that a major diamond deposit does exist there. It is probable that it will be found before the end of this decade and exploration expenditure may be in the order of $100 million.

Jan 1, 1992

By T. Moyo

Ammoniacal solutions are attractive and effective lixiviants for the dissolution of chalcopyrite, allowing for the formation of stable ammine complexes with copper while rejecting iron. Chalcopyrite dissolution in ammoniacal solutions is reviewed from literature, and results from a recently completed study evaluating it through electrochemical and controlled leach studies are discussed. Ammoniacal leaching of copper ores dates back to 1916 in the leaching of low grade copper ores in the Kennecott leaching plant and in the Calumet and Hecla mines, followed by the commercialisation of the Sherrit Gordon process for the ammoniacal leaching of sulphide copper ores in 1948. Since then ammoniacal leaching has received intermittent focus from researchers with the development of the Anaconda’s Arbiter process and the unsuccessful Escondida process. In these leaching processes, the formation of surface deposits has historically been reported to result in the passivation of the chalcopyrite surfaces, whereas oxygen mass transfer in solutions has been the focus of process design improvements. Results of studies on high grade chalcopyrite material is presented in this paper which show that although a surface deposit was formed, it did not result in the passivation of chalcopyrite in ammoniacal solutions, and that while oxygen transfer is critical, it is not the direct oxidant in the reaction. INTRODUCTION Ammonia and its salts have been used in the hydrometallurgical treatment of non-ferrous metals such as copper, cobalt and nickel from oxide ores. Its chemistry allows for the selective dissolution of desired metals, leaving behind gangue including iron. Chalcopyrite is a copper sulphide ore known to be very stable and hence recalcitrant to many hydrometallurgical processing methods. Thus, the dissolution of chalcopyrite continues to be an attractive area of research. The dissolution of chalcopyrite in ammoniacal solutions is possible due to the stabilisation of copper(I) and copper (II) ions by ammonia in alkaline media. Ammonia has become more attractive as a lixiviant during the present socio-economic climate due to its low toxicity, relatively low cost and ease of regeneration by evaporation (Meng & Han, 1996). Ammonia processes are ideal when the gangue minerals are acid consuming e.g. with calcareous or dolomitic gangue (Paynter, 1973).

Jan 1, 2019

By Gerhard Kircbner, Boen Tan

"IntroductionThe Key Lake uranium-nickel ore deposits are located in the Athabasca Basin of northern Saskatchewan, Canada (Fig. 1). Many papers have been published on Key Lake in the past (Dahlkarnp and Tan, 1977; Kirchner and Tan, 1977; Kirchner et al., 1980). Immediately after its incorporation in 1968, Uranerzbergbau GmbH, a German holding company, set up exploration subsidiaries in Australia, the United States and Canada. This account reviews those exciting years starting with the concept to explore the rim of the Athabasca Basin in Saskatchewan, and leading up to the discovery of the deposits in 1975 and 1976.A few summary statements can be made:• The discovery of Key Lake resulted from a very systematic exploration approach and the persistence of Uranerz, the operator. • Cluff Lake and Rabbit Lake had been discovered some seven years before, but it was the discovery of the Key Lake deposits which brought Saskatchewan to the forefront to become Canada&apos;s foremost uranium producing province.• The experiences gained at Key Lake, which were subsequently published, triggered the discovery of many other deposits of similar, or even larger, size than Key Lake. The spatial relationship of those deposits to graphitic conductors and hydrothermal alteration zones are presently the most effective indicators for locating new deposits - indicators which were first recognized at Key Lake.• Key Lake is, and will remain for some years to come, the largest producing high-grade uranium mine in the world."

Jan 1, 1994

By Gustavo Brunello

Motor Failure Rates and Cost ? Motor failure rate is estimated: 3-5% per year. ? In Mining, Pulp and Paper industry failure rate is up to 12%. ? Sometimes process downtime costs are higher than motor ?? Motor failures are due: Electrical 32% Mechanical 31% Environmental 36%

Feb 1, 2008

The steam-filtration process for dewatering solids involves the application of slightly superheated steam to a filter cake during filtration. The mechanism by which the technique promotes water removal has been deduced from bench-scale experiments on coal and on granular iron ore concentrates. The mechanism, along with some of the applications and limitations of the process, is presented. Introduction I N the steam-filtration process, slightly super-heated steam is applied to the filter cake during filtration to remove more water than can be extracted by conventional filtration. Although this process was developed by Burton for coal filtration (1), it should have far wider applicability; certainly, it could be used to treat any mineral product, because only low-temperature steam is needed and most conventional filtration equipment can be easily adapted to it. As few restrictions apply to this process, however, it is important that its more obvious advantages and disadvantages be appreciated and, especially, that the criteria on which economic evaluations can be based are understood.

Jan 1, 1965

By H. C. Cooke

"The Part of the Eastern Townships dealt with in this paper is shown in the accompanying figure. Each rectangle represents one of the topographic maps published by the Department of National Defence on a scale of one mile to one inch. Each sheet covers an area approximately 24 miles long and 17 miles wide, or slightly more than 400 square miles. The north-western part of the area figured, comprising the Upton, Aston, Becancour, and the two unnamed sheets, (Three Rivers and Yamaska), together with most of the Lyster, Drummondville, and St. Hyacinthe sheets, is largely covered by clays and sands deposited in interglacial and post-glacial time in the Champlain estuary, so that outcrops are widely scattered and in-formation is correspondingly sketchy. In the remainder of the area figured, comprising more than 4,000 square miles, outcrops are reasonably numerous and have been mapped on a scale of one mile to one inch, and the structure is moderately well understood.The Eastern Townships was an area of intense orogenic disturbance, apparently beginning late in the Cambrian or early in the Ordovician, and continuing till well on in the Devonian period. During this long period, which may have lasted for a hundred million years or more, the area was subjected from time to time to intense thrusts from the east and southeast. Each of these caused folding of the rocks, accompanied by faulting, raised parts of the area above sea-level, and presumably created ranges of mountains. Long periods of erosion cut away the mountains and reduced the area nearly to sea-level after which subsidence carried it below sea-level, and permitted further sediments to accumulate before the next thrust initiated the next cycle.The first of these movements, as stated, appears to have been in late Cambrian or early Ordovician time. The group of rocks known as Caldwell was folded and, south and east of the town of Asbestos, was thrown into great drag-folds before deposition of the next overlying series, termed the Beauceville, began. Unfortunately, the date of this orogeny is very imperfectly known, because both series of rocks have been so crushed and sheared that almost all fossil remains have been destroyed. Graptolites, found in one place in slates generally considered Beauceville, give that series a tentative Middle Ordovician age. In the Caldwell rocks, which underlie the Beauceville with great unconformity, no fossils whatever have yet been found. Thus, if the Beauceville rocks are correctly dated as mid-Ordovician, the best that can be said of the movement folding the Caldwell is that it took place at some time before Middle Ordovician."

Jan 1, 1949

By Richard E. J. Putman

THE MINERALS INDUSTRY has always been a heavy user of energy in most of its unit operations: power in the mining, comminution, flotation and electro-winning processes; fuel in its smelting and other metallurgical processes; and, of course, fuel in the on-site generation of power and steam. Many of the techniques for using computers to perform energy management and conservation tasks have been known for some time, but they have not been widely implemented because the return on investment has hitherto been insufficient. Recent trends, however, have not only caused the dollar return to rise due to higher purchased energy costs, but the cost of the investment to fall. One trend has been the generally lower cost of computer control systems themselves, due to vendors having adopted the newer, lower-cost and more reliable electronic component technologies now becoming universally available. The second trend is the development of low-cost, but high-speed, remote multiplexing devices, which have reduced considerably the expense of bringing data from points scattered over a wide area, which is typically the case when applying energy management systems to a minerals processing plant. By taking advantage of these and related developments, computer control systems can now have a rewarding impact on plant energy management and conservation practices, and recent advances in application technology have opened up new and additional opportunities for energy cost reduction and control.

Jan 1, 1978