Search Documents

By R. K. Collings

The annual production of mineral and mineral-based wastes in Canada is conservatively estimated to be 400 million tons. Over 90 per cent of this amount is waste rock or mill tailings from the mining and mineral processing industry. The remainder are slags and ashes from the metallurgical industry, and sludges from the chemical industry. Because of impurity content, remote location, or both, most wastes have limited usefulness and, indeed, are a liability in that they must be transported to waste disposal sites and contained therein. Certain mineral wastes do, however, have potential value. Some contain small percentages of metals that may be economically recoverable with price increases; others consist of mineral material that may be used for such purposes as road base, construction aggregate, railroad ballast, and in the manufacture of bricks or blocks. Increased interest has been shown in mineral wastes in recent years. This paper reviews the types of mineral wastes available in Canada, briefly describes a number that have potential value, and notes possible uses and related research by CANMET and other organizations.

Jan 1, 1978

The Carboniferous sedimentary rocks of southwestern Newfoundland merit investigation because of petroleum, salt and gypsum possibilities and indications of base metallization along the equivalent of the Horton-Windsor con-tact. In this paper, Lower Mississippian (Anguille) strata are divided into three formations: (1) the Cape John below, (2) the Snakes Bight and (3) the Seacliffs. A correlation between these formations and the Craignish, Strathlorne and Ainslie formations of the Horton group? in western Cape Breton Island is suggested. The criteria for the Anguille subdivision are essentially lithological, but preliminary study of included spore assemblages suggests more precise interformational correlations between Anguille and Horton sequences. The re-measured lower portion of the type section of the Codroy group is presented to define more clearly the stratigraphic position of numerous gypsum and limestone beds. Because of rapid facies changes within the Codroy group a simplified two-fold division into upper and lower units is proposed on the grounds of

Jan 1, 1964

By M. L. Jeremic

"Hydraulic mining consists of coal erosion by powerful jet s of water from hydraulic monitors operated by remote control. The broken coal is crushed and mixed with water and then transported from the face to the surface using gravity whenever possible. This is a simple, safe and productive method. It will easily satisfy North American productivity standards if the structural features and coal properties are favourable for water jet cutting technology (Kaiser Resources Ltd. , hydraulic mine). General ConsiderationIn open-pit mines, placer mining (Fig. I) and hydroelectric construction projects, hydraulic earth moving techniques have been successfully applied. The stripping and transporting of the overburden has been accomplished by means of large monitor jets augmented by slurry pumps and pipes. An extension of this technique has led to the underground extraction of coal and ores. To date, the method has been most successfully used in undergrond coal mining, because the coal can be easily cut and flushed away by water jets, and the rocks of the roof strata can be left behind. Due to this favourable situation, the hydraulic mining definition only relates to the underground coal mines.At present, there are four basic types of hydraulic mining, which can be defined according to the coal breaking technique used in each case. The methods are briefly discussed below:(1) Coal excavation may be carried out by conventional techniques, but the mine is designed and equipped for the hydraulic transport of the mineral from the working place to surface. Under these circumstances, the coal breaking may not be influenced by the water jet, however it may be indirectly involved. For example, pre-loosening of the coal may be done by water infusion-hydraulic fracturing. Water may also be used to flush the broken coal, which has been excavated either by drilling and blasting or by mechanical cutting, into the transport flumes. In other cases, a mechanical loader may load the coal directly into the hydraulic transport system, without using any water for the extraction process. This hydraulic mining concept is primarily used for hard and impermeable coal, such as anthracite."

Jan 1, 1980

By Richard J. Wardle, Ambrose F. Howse

The industrial minerals industry in Newfoundland and Labrador is a significant contributor to the provincial economy. The variety ofcommodities produced reflects the diverse geological environment from which they come. A highlight of the past decade has been the continuing development of dimension stone quarries, with producers now active in anorthosite, gabbro, granite and sandstone. Other dimension stone prospects have been identified and are in various stages of assessment and development. Western Newfoundland hosts a large resource of limestone, dolomite and marble. It provides raw material for industries that produce Portland cement, agricultural limestone and aggregate, as well as chemical-grade limestone and dolomite products. In western Labrador, dolomitic marble is quarried for use in the production of self-fluxing iron ore pellets. The recent opening of a new gypsum quarry at Fischells Brook signalled the beginning of a new era in the commercial production ofgypsum, a commodity which the province has produced since the 1950s. Hopefully it will emulate the nearby Flat Bay Quarry (now closed) which was a long-time exporter to markets along the U.S. eastern seaboard, in addition to supplying local demands. Oil production and continuing exploration in the Newfoundland offshore has renewed interest in local barite deposits for potential use in drilling fluids. Already there has been some production from the Collier Point deposit, and at Buchans, an existing plant is being refurbished to recover barite from a large tailings pond. Emerging new industries include the development of an antimony mine in central Newfoundland, the development of silica deposits near Labrador City for silicon metal production, and reactivation of the St. Lawrence fluorspar mine. The province has many deposits with development potential such as rare metals at Strange Lake, white marble at Roddickton and salt deposits near St. George's Bay region.

Jan 1, 2001

By J. Keith Haddock

"Introduction The Boundary Dam Mine is located 5 km south of the City of Estevan, Saskatchewan and is operated by Manitoba and Saskatchewan Coal Company Ltd., one of the Luscar companies. The entire production of 1.7 million tonnes per year is delivered to the Boundary Dam Generating Station of Saskatchewan Power Corporation. Geology There are basically two seams mined on the property, the main Estevan seam ranging in thickness from 3.0 m to 4.5 m with partings and the upper Roche Percee seam (roughly 15 m to 23 m above the Estevan) which ranges from 0.6 m to 2.0 m in thickness. Most of the reserves are concentrated in the Estevan seam, the Roche Percee only being mined whenever its thickness makes it economic to recover. The coal measures belong to the Ravenscrag Formation of Tertiary (Paleocene) Age. This formation is widespread in North Dakota and Montana and contains the lignite fields of North Dakota and subbituminous coals of Montana. The formation is gently tilted to the southeast at Boundary (0.5 degrees) and consists of weak sandstones, siltstones and silty mudstones. Reserves and Coal Quality The present minesite encompasses a coal reserve of approximately 50 million tonnes calculated to a maximum stripping depth of 37 metres or 20:1 mining ratio. The reserves form only a part of the total reserves in the Estevan area which are owned by the Saskatchewan Power Corporation. The coal being mined is classed as Lignite ""A"" and has the following specifications:"

Jan 1, 1985

By C. R. Edwards, D. G. Feasby

"Over the last 50 years disposal of uranium mill tailings has evolved from dumping untreated tailings into the nearest depression to depositing chemically-stabilized tailings into highly engineered management facilities. This paper describes the evolution of disposal methods and the criteria which have determined the development path followed. Remediation techniques to bring older and now unacceptable tailings deposits into satisfactory compliance with today's· regulations are reviewed.With the closure of the uranium mines in Elliot Lake, Ontario, considerable effort is being made on decommissioning the tailings areas by developing long term maintenance of water covers. The innovative methods being used to develop these water covers are detailed. Methods now under development in Saskatchewan for subaqueous deposition of high density or paste tailings for permanent disposal in mined out open pits are described.SummaryThe technology for uranium mill tailings disposal in Canada has evolved considerably over the past 51 years. This evolution has been driven by an improving understanding of how best to safely and permanently store tailings, in conjunction with stricter environmental protection regulations. Old sites are being decommissioned in situ, but may require long term care and maintenance. The use of water covers is an important technique in eastern Canada to prevent intrusion, radon evolution and, for the Elliot Lake tailings, acid generation. The major drawback of water covers in any above ground disposal method is the requirement that a long term maintenance and monitoring plan be put into effect for each site.New higher grade mines in Saskatchewan will increasingly use disposal in mined-out pits using the pervious surround method and/or paste tailings technology as a method to permanently dispose of these wastes and to permit “walkaway” after a few years of monitoring."

Jan 1, 1996

By T. R. Yu, D. B. Counter

"In an effort to increase productivity, the use of fly ash as a binder for consolidated backfill was studied. From laboratory and underground tests f or its cementitious properties and environmental effects, it was found that a portion of Portland cement could be replaced by the same amount of type ""C"" fly ash to produce an acceptable consolidated rockfill product for use at Kidd Creek.The environmental concerns in terms of dust control and emanation of radon gas were unfounded from measurements. The dust count was comparable to the use of Portland cement only, or with ground blast furnace slag, and the radiation readings were low, averaging one-seventh the regulation level.Since May 1984, a total of over 100 000tonnes of fly ash has been consumed as a binder blended with Portland cement, producing over four million tonnes of consolidated rockfill. To date, the fill in the stopes has performed very satisfactorily, while yielding considerable cost savings.IntroductionThe Kidd Creek minesite, located 27 km north of the city centre of Timmins, Ontario, produces 4.5 million tonnes of base metal sulphide ore annually. The mining method for both No. I and No .2 mines is mainly sub-level blasthole stoping with delayed backfilling.No. 1 mine was developed with a shaft to a depth of 930 m in 1973 to recover the ore between the floor of the open pit at the 216 m horizon, and the 792 m horizon. Stopes are normally 18 m wide, 22 m to 65 m long, with heights varying from 90 m to 135 m. Vertical rib pillars between stopes are typically 24 m wide and sill pillars are 30 m thick.Pillar recovery is implemented after the consolidated rockfill placed in the mined stopes has cured for a period of at least three months. This allows a maximum recovery of the ore with a minimum of dilution, while also maintaining safe working conditions.No. 2 mine was developed from a second shaft, sunk to a depth of 1530 m in 1978, for the recovery of ore beneath the No. I mine. Sub-level stoping in No .2 mine is similar to No.1 mine in methodology, yet differs in sequencing, as no rib pillars are left."

Jan 1, 1988

By B. R. Casement

"Managing safety on the basis of after-the-fact reaction to accidents, can never be more than partially successful. Injuries will occur as long as the underlying potential for them still exists. Unless unsafe actions and conditions are systematically decreased, no program can have more than a short-term success.The pro-active Bullmoose loss control process, instead, focusses on heightening awareness of work habits, to prevent incidents by reducing their potential.Any safety program will be doomed to failure if the development of safe work habits depends on the safety supervisor or a safety committee. At Bullmoose the focus is on the critical actions out of which losses emerge. The successful application of performance-related feedback is achieved by taking safety, health, and environmental concerns into consideration on every level, and, by doing the right thing in every job done.What is an Exceptional Loss Control Program?If an accident in an organization creates a flurry of interest, resulting in ""cracking down"" on violations for a short period of time then an ""exceptional"" loss control program exists. Unfortunately, exceptional here does not refer to the effectiveness of quality of the program but to the fact that the organization is managing loss control by exception. The degree of management attention in an ""exceptional"" safety program varies over a period of time, remaining low as long as the rate of losses stays within management's acceptable control limit (Fig. I). When the losses rise above this, management becomes motivated to begin ""exceptional"" efforts to manage losses. When the rate falls again to within the accepted limit, efforts to control losses take a back seat.Such a strategy guarantees that losses will be tolerated or ignored as long as the actual rate is below the acceptable limit. Simply to lower the limit would not reduce losses, but would result in an increased number of flurries of management attention to loss control. This ""on-again, off-again"" style of management teaches supervisors and others that basic loss control is not as important as are statistics."

Jan 1, 1993

By Nav Dhadli

Tailings from Oil Sands MiningWhat are they? Challenges Solutions Regulatory Environment Definition of the AFD Tailings Treatment Process 2010 AFD Pilot/Demonstration ProgramTechnical challenges Performance and Results Next steps Oil Sands Industry Collaboration on Tailings Technology TAILINGS ?WHAT ARE THEY? Mixture of remaining water and solids following bitumen extraction process Composed of water, sand, silt, clay, small amounts of hydrocarbon (bitumen, solvent, and asphaltenes) A necessary part of production in excavation of oil sands and removal of bitumen

May 1, 2011

By E. Ghali, W. Zhang, M. Robichaud, G. Houlachi

"The performances of six mesh and one plate dimensionally stable anodes have been investigated in the zinc electrolyte at 38oC and compared to conventional silver-lead alloy anodes. The electrochemical behaviour of these anodes was studied by cyclic voltammetry, galvanostatic, potentiodynamic, open circuit potential and electrochemical noise measurements. It was observed that at the end of 24 h of galvanostatic polarization at a current density of 50 mA/cm2 in the zinc electrolyte at 38oC, the mesh V had the lowest potential followed by mesh III, mesh VI, plate-V, mesh IV, mesh I, and mesh II electrode. When the potentials for mesh I, mesh III, mesh IV, VI and plate-V, mesh V were compared with that of the Pb-0.7%Ag anode (1920 mV/SHE), they were found to be 6%, 16%, 7% 10%, 17% lower, respectively.After 16 h decay following the 24 h polarization, the mesh III had the lowest corrosion rate (51 mS/cm2) among the seven specimens, followed by the plate-V, mesh V, VI, IV, I and II (221 mS/cm2). For the fresh surface as received, after two hour open circuit potential measurements, mesh I had the most positive (noble) potential (1382 mV/SHE) among the seven electrodes followed by the plate-V electrode, mesh V, mesh IV, mesh VI, mesh III and mesh II (751 mV/SHE). After consecutive series of electrochemical testing, mesh V, mesh III, mesh VI had lower corrosion rates (~ 343± 6 µA/cm2) than that of mesh IV, mesh I, plate-V, and mesh II (~ 644± 143 µA/cm2).INTRODUCTIONThe continued use of lead based anodes in the electrowinning process has been mainly due to their relatively low cost as compared to other materials (Msindo, Sibanda, & Potgieter, 2010). They have good electrical conductivity, stability during electrolysis, very good corrosion and wear resistance (Ivanov, Stefanov, Noncheva, Petrova, Dobrev, Mirkova, Vermeersch, & Damaerel, 2010). However, lead-based anodes give their high energy consumption and low corrosion resistance for electrowinning. To overcome these problems, Dimensionally Stable Anodes (DSAs) has been chosen (Msindo et al., 2010). Comparing to the traditional lead anodes, the DSA anodes have many advantages: (1) no contamination; (2) no loss of anode material, pure electrolyte; (3) lower gas bubble effect through special anode designs; (4) use of higher current densities (Msindo et al., 2010). The success of DSA anodes has been attributed to their chemical stability that allows them to maintain nearly constant dimensions during the life of the anode even when operating in environment with low pH values. Due to their stability, the consumption rates of DSA are as low as 1 mg/amp.y (Alfantazi & Moskalyk, 2003)."

Jan 1, 2016

By Robert B. Parsons

"The 1994 Quebec Budget included a significant overhaul of the mining duties sys-tem in that province: broadening the base and lowering the rate, all in the name of “ensuring the integrity of the taxation system"" and ""enabling the State to collect fair compensation "". The reforms hit hardest on the small, lightly-capitalized producer, by repealing the basic annual exemption, limiting the refund for losses, and significantly reducing the investment and processing allowances. There is some relief provided in the form of faster depreciation rates and a lower nominal tax rate, but the thrust of the overhaul is clear -higher taxes on the mining sector.IntroductionAlthough Quebec's mining tax regime represents under 10J0 of the province's revenue base, and was significantly reformed in 1979 and 1985, the May 13, 1994, provincial budget introduced further significant changes to the Mining Duties Act, The hope (on the part of the province) is to reduce the provincial ""subsidy"" for mining by $20 mil· lion per year by 1996."

Jan 1, 1995

By R. P. Chapman

The geochemical interpretation of results of statistical analysis of published multi-element stream sediment data from southwest and northern New Brunswick is presented. Element concentrations in southwest New Brunswick are low and comparable to element concentrations in background areas in northern New Brunswick. Deposits of copper and nickel are indicated in southwest New Brunswick. Anomalous element concentrations occur in several areas in northern New Brunswick and the elements most commonly associated with these anomalies are Cu, Pb, Zn, As and Ag; and also Mo, Wand Sb. Bedrock geology greatly influences element concentrations and may cause false anomalies. Manganese has a pronounced effect on the dispersion patterns of Co and also Zn, Mo, Pb, As, Ba and Ni. Nickel and Cr are strongly sympathetically related and this association is independent of bedrock type.

Jan 1, 1977

By J. K. Szymanski

"RÉSUMÉPour maintenir de bonnes performances technique et économique dans l’exploitation par chambres vides (open stope) il est primordial d’assurer un contrôle efficace des limites réelles des chantiers d’abattage. C’est pour cette raison que, de plus en plus souvent, les opérateurs miniers utilisent un dispositif de laser (Cavity Monitoring System: CMS) qui permet de mesurer les dimensions réelles de chantiers en vue de calculer principalement la dilution et les pertes du minerai ainsi que d’autres paramètres. Malheureusement, il n’existe présentement aucune méthodologie commune, qui permettrait d’interpréter ces résultats selon les mêmes critères pour faciliter d’évaluations juste et précise de la réalisation par rapport à la planification en vue d’en apporter de corrections, dans les différentes opérations minières, si nécessaire. Dans la première partie du présent article on discute les principales séquences d’exploitation utilisées dans l’extraction par chambres vides. Par la suite, à l’aide des sections transversales et longitudinales on illustre toutes les phases des travaux miniers. Ceci en vue de permettre au lecteur de comprendre mieux c’est qui peut se passer effectivement dans les chantiers d’abattage. Par après on donne les définitions générales de principaux facteurs de performance technique. Finalement, l’exemple numérique, élaboré à partir des résultats de l’arpentage au laser effectué par la mine Bousquet 2 dans un chantier d’abattage, donne les détails concernant les définitions ainsi que les valeurs de nombreux facteurs de performance technique, qui pourraient être utilisés, par après, par les opérateurs miniers dans le suivi de leurs exploitations souterraines."

Jan 1, 1997

By L. C. Galloway, G. L. Tiley

"Mine hoist brakes must meet the following statutory performance criteria:- There should be two independent braking systems; at least one should act directly on the hoist drum.-If one brake fail s, the others should be able to retard and stop the hoist safely before the descending conveyance, carrying the rated load, reaches any obstruction.- When all brakes apply, decelerations should not be so violent that men travelling in the conveyance are injured.- The brakes shall not overheat and fade during an emergency stop.This paper discusses design principles and capacities of caliper and disc type brakes, when applied to double drum and friction hoists of equivalent capacity.IntroductionThis paper is about the brakes that are used on mine hoists; their functions, especially in emergencies, typical design, and how they are operated, controlled, tested, and adjusted.There are two basic types of mine hoists:1. Drum hoists, where the ropes are attached to, and coil on drums. The simplest system has only one drum. Most such hoists, however, have two drums, attached to a common shaft. Ropes are wound on each drum in opposite directions, so that when one conveyance is being raised, the other is lowered. The conveynaces may travel in vertical or inclined shafts. In the latter case, the hoist s are referred to as slope hoists.2. Friction hoist s, where the headropes are not attached to the wheel, but are in contact with it for an angle of lap of, typically, between 180 and 195 degree s. Forces are transmitted from the hoist wheel to the head ropes by friction.The lower ends of the conveyances are connected to balance ropes , approximately the same weight per foot as the headropes."

Jan 1, 1986

By R. Pandher, R. Schonewille, N. Tripathi

Advanced process modelling tools were developed for the Xstrata Nickel Sudbury Smelter flow sheet using a combination of FACTSAGE TM METSIMTM and ARENATM software. These tools were employed to assist with plant optimisation, emission control, process design, troubleshooting and case studies as applied to the smelter. The development of process modelling tools in pyro-metallurgy commonly involves an in-depth study of the therm o-chemical properties (heat capacity, liquidus temperature, etc.) of all high temperature phases, usually matte and slag. The preferred tool for this purpose is FACTSAGETM, a well-known then-no-chemical modelling software package. The results from the therm o-chemical model have been subsequently incorporated into the development of a process model for the entire smelting facility using the METSIMTM platform. Such process model also includes a number of special features adopted to effectively simulate the complex industrial phases; matte and slag systems. To ensure the robustness and reliability of the process model, several process parameters and assumptions were verified with laboratory and plant data. Consequently, the model includes the ability to examine the impact of a number of plant parameters on potential plant performance. Primary variables are the percent sulphur elimination during concentrate roasting, furnace matte grade and degree of matte metallization. Key output parameters include operating temperature, furnace coke requirement, sulphuric acid production, CO2 emissions and overall energy requirements. Selected outputs from the process model (for example blowing time, slag production rate and matte converting rate) can then be utilised in the development of a discrete event model (DEM) for the smelter using ARENATM software. Incorporation of reliable and validated mass balance parameters enhances the robustness and reliability of the DEM model. The integration of then-no-chemical, process and DEM modeling tools has a distinct advantage in planning plant trials and examining process design initiatives at Xstrata Nickel's Sudbury Smelter. The present paper discusses the development of these three models and the synergies existing among them. Typical results from all three models are also presented.

Jan 1, 2011

By R. Pandher, R. Schonewille

Advanced process modelling tools were developed for the Xstrata Nickel Sudbury Smelter flow sheet using a combination of FACTSAGETH METSIMTM and ARENATM software. These tools were employed to assist with plant optimisation, emission control, process design, troubleshooting and case studies as applied to the smelter. The development of process modelling tools in pyro-metallurgy commonly involves an in-depth study of the therm o-chemical properties (heat capacity, liquidus temperature, etc.) of all high temperature phases, usually matte and slag. The preferred tool for this purpose is FACTSAGETM, a well-known then-no-chemical modelling software package. The results from the therm o-chemical model have been subsequently incorporated into the development of a process model for the entire smelting facility using the METSIMTM platform. Such process model also includes a number of special features adopted to effectively simulate the complex industrial phases; matte and slag systems. To ensure the robustness and reliability of the process model, several process parameters and assumptions were verified with laboratory and plant data. Consequently, the model includes the ability to examine the impact of a number of plant parameters on potential plant performance. Primary variables are the percent sulphur elimination during concentrate roasting, furnace matte grade and degree of matte metallization. Key output parameters include operating temperature, furnace coke requirement, sulphuric acid production, CO2 emissions and overall energy requirements. Selected outputs from the process model (for example blowing time, slag production rate and matte converting rate) can then be utilised in the development of a discrete event model (DEM) for the smelter using ARENATM software. Incorporation of reliable and validated mass balance parameters enhances the robustness and reliability of the DEM model. The integration of then-no-chemical, process and DEM modeling tools has a distinct advantage in planning plant trials and examining process design initiatives at Xstrata Nickel's Sudbury Smelter. The present paper discusses the development of these three models and the synergies existing among them. Typical results from all three models are also presented.

Jan 1, 2011

By P. F. Berry

X-ray fluorescence analytical techniques are fairly well established in the mining and metallurgical industries. In recent years, instruments utilizing radioactive isotopes have been developed which, owing to their more compact size, greater reliability and independence of substantial power supplies, are often preferred to X-ray tube installations. Analyses can now readily be carried out in the field, on the factory floor and in otherwise difficult locations. This paper describes many examples of radioisotope X-ray fluorescence for the analysis of metallic minerals, finished metals and alloys and also for the continuous measurement of metallic coatings, such as tin and zinc, on steel. Radiation scatter techniques are also described for certain analyses and for thickness and density measurements.

Jan 1, 1967

By J. Visman

The water cyclone washer has a number of advantages that makes it a desirable machine for the cleaning of fine-grained and friable materials such as 1,4 x 0" slack coals. In this paper results are presented of tests carried out on a shaly coal containing a high percentage of inter-grown materials from the Minto area, New Brunswick. The tests were con-ducted in the pilot plant of the Western Regional Laboratory in Edmonton. The test results show that the cleaning characteristics of this coal can be improved by lightly grinding the recirculating middlings fraction, which constitutes approximately 30 per cent (1.45-2.00 fraction) of the raw feed. • The cleaning of 1;4 x 0" fines by water cyclones compares favourably with other coal cleaning machines and has an added advantage of being extremely simple to operate, low in capital and operating cost, and high in capacity. The application of water cy-clones dates back approximately ten years, following its development at the Dutch State Mines. ( 3) A number of papers published d

Jan 1, 1961

By G. Van Weert, O. Wang

"As part of a general review of processing double refractory ores through Barrick Gold’s autoclaves / CIL facility at Goldstrike, blanking the preg robbing native carbon in the process solids with hard (m.p. 55 - 60 º C) paraffin wax was studied, specifically in relation to pressure oxidation. The improvement in CIL gold extraction was found to depend on the wax addition point, with hot, dry contacting of the ore in the presence of wax - prior to POX - yielding the largest, most consistent improvement in gold extraction.INTRODUCTIONDouble refractory gold ores present two barriers to gold extraction. The first is generally a physical barrier: the gold is encapsulated or dispersed in a matrix which is impervious to the gold lixiviant. In most cases, including Carlin Trend, NV, deposits, this involves a pyrite or arsenopyrite matrix, although minor gold may also be dispersed in competent silica (quartz) or iron oxides. Gold can be rendered accessible by oxidative destruction of such sulphide matrices. At Goldstrike this is practised by roasting and autoclave oxidation (Thomas, 1994). It is the latter route to which this paper refers.The second barrier refers to the actual gold recovery. Gold may be extracted from the pressure oxidized solids with cyanide, forming a gold cyanide complex. One characteristic of this complex is that it adsorbs on graphitic surfaces. This is taken advantage of on a large scale by gold millers, who use manmade activated, i.e., graphitized carbon particles to remove the gold from solution during leaching: the Carbon-In-Leach, or CIL process. The gold cyanide bearing carbon particles are larger than the ore solids and can be separately recovered by screening. Goldstrike uses the CIL technology to recover gold. The second barrier becomes problematic when the ore naturally contains graphitic orcarbonaceous material, hereafter referred to as native carbon (versus the man-made activated carbon). This material may also adsorb gold cyanide in competition with the activated carbon. Since the native carbon is ground with the ore it is much smaller than the activated carbon. Any competition between the two carbons may produce a loss of gold from the pregnant leach liquor to the process tailings. This phenomenon is called “preg robbing”. Goldstrike ores come from the Carlin trend, which is known for the occurrence of native carbon (Adams & Burger, 1998; Schmitz, Duyvesteyn, Johnson, Enloe & McMullen, 2001; Tretbar, 2004)."

Jan 1, 2012

By A. Cummings

This paper reports two aspects of reactivity of complex Ni-Cu sulphide ores: variations that result from stockpiling of a nickel-copper sulphide ore in the Sudbury area and its consequences on flotation behaviour, especially in terms of metal losses to scavenger tails. In relation to the first aspect, self-heating characteristics of the stockpile were carried out by monitoring the internal temperatures of the stockpile. Six heat sensors were installed with respect to external conditions in local weather during a 7-month period. Stockpile temperatures were mainly influenced by ambient temperature with some retardation effects. The maximum temperature recorded in the stockpile was 44 °C. Samples taken at the beginning and at the end of stockpiling were tested to assess variations in behaviour of the rougher-scavenger flotation. Relative to the fresh ore, nickel and copper losses in flotation of the stockpile fines were 5.0 and 3.6 %, respectively. The fresh ore yields concentrates with higher nickel grades due to differential flotation behaviour of pentlandite and pyrrhotite relative to the stockpile fines, which exhibit a truly bulk flotation behaviour at least during the first 3 stages.

Aug 1, 2013