Search Documents

By Brian Lewis

"IntroductionThe leaching method selected for the dissolving of uranium ore depends in part on the physical characteristics of the ore, as well as the uranium mineralization. There are two main methods of leaching employed in uranium circuits in North America, one being ""Carbonate Leaching"" on sandstone, and pitchblende type ores, and ""Acid Leaching"", on quartzite type ores.This chapter deals with the acid leaching of uranium ores found in the Elliot Lake area, using sulphuric acid, for the leaching reagent, and ""pachucas"" for the contactor.The basic leaching process involves the pregrinding of the ore and the mixing of the ore with hot sulphuric acid, the mixture is air agitated, the air being used to oxidize the ore as well as produce agitation. The chemical reaction is as follows: Uranium Oxide + Sulphuric Acid = Uranyl SulphateThe following equations show the actual dissolution of the ""Hexavalent Uranium"", which show that more than one ion or complex of uranium is possible.Uranium DissolutionsI. UO, + 2H-(UOJ + H,O2. (UO,) + SO, = -UO, SO, (Uranyl Sulphate)3. UO, + SO,-(UO, (SO,),)=4. (UO, (SO,),)= -(UO, (SO,),)'Test work carried out in the laboratory as well as in the plants has determined the most efficient methods of extracting the uranium from the ore. A very important factor that has to be determined during initial test work are the amount of acid consumers in the ore. Within the Elliot Lake orebodies are minerals such as chlorite schist, diabase, and basement material, all very high acid consumers, consuming up to 1000 lbs. of acid per ton of ore. Of these minerals only the chlorite schist contain any uranium at all.The following are the operating parameters that have to be controlled in the plant:I. sulphuric acid concentration2. temperature of the mixture3. agitation4. liquid solid ratio5. reaction time6. particle size of ground ore"

Jan 1, 1989

By H S. Ellis

Flow studies have been conducted on nickel-water suspensions in a 1in.-diam., 42-ft.-long transparent lab-oratory pipeline at concentrations of up to 25 per cent, by volume, and slurry velocities of up to 15 ft/sec. The average size of the nickel powder was approximately 150 mesh (106J.L). Three flow regime were noted. At the highest velocities, i.e., above 10 ft/;sec., where the concentration distribution through the vertical diameter was most uniform, pressure gradients could be correlated with the Durand-Condolios equation (7,8). An intermediate region, i.e., from 7 ft/sec. to10 ft/sec., could be distinguished, the lower velocity limit being that at which nickel particles began to deposit. This region was also marked by decreasing pressure gradients, for a given concentration, as the velocity was reduced. The upper velocity limit in this region was also uniquely defined in that the friction factor for any nickel concentration was the same as that for water. In the third regime, below about 7 ft/sec

Jan 1, 1963

By Denis Blackburn

La Direction générale du développement de l?Industrie minérale (DGDIM) du ministère des Ressources naturelles et de la Faune (MRNF) du Québec tient un inventaire de toute l?activité minière sur le territoire. Cet inventaire s?est enrichi, au cours des dernières années, d?un grand nombre de projets dédiés au fer ou à des substances qui y sont associées (titane, vanadium, phosphate). Actuellement, cinq régions du Québec sont principalement touchées par la recrudescence de projets dédiés au fer : Fermont, Schefferville, Baie d?Ungava, Baie-James et Chibougamau. Fermont et Schefferville sont les régions les plus actives. Les infrastructures en place, telles que les routes, les chemins de fer, les ports, les lignes électriques et les municipalités, ont atteint, dans certains cas, leur capacité et de nouvelles infrastructures devront être construites pour satisfaire les besoins. À la Baie-James et sur le flanc ouest de la Baie d?Ungava, des projets d?exploration sont aussi en cours. Le manque d?infrastructure pourrait peser lourd sur le développement de projets miniers dans ces régions. Enfin, dans le secteur Chibougamau/Matagami et à quelques sites ailleurs au Québec, des projets d?exploration qui visent le vanadium, le titane ou le phosphate pourraient aussi fournir comme produit secondaire des concentrés de fer. Tous les projets, décrits dans cet article, sont situés sur le territoire du Plan Nord du gouvernement du Québec.

May 1, 2011

By S. Shairp

"After cooling and thickening, slurry from the second stage of the Hudbay zinc pressure leach circuit is filtered and washed on a belt filter prior to disposal. At times, the belt filter can be a bottleneck to the process. Preliminary studies show that filterability of the second-stage (HAL) autoclave leach residue can be indicated by particle size distribution of the filter feed and filtered residue cake. In particular, the Volume Weighted Mean Diameter, D[4,3], generated by a laser diffraction particle size analyzer from samples of HAL Filter feed, shows residues that filter more poorly have a lower Volume Weighted Mean Diameter than those that filter better. INTRODUCTIONHudbay produces cast zinc metal from blends of zinc concentrates at its metallurgical complex in Flin Flon, Manitoba, Canada, using Sherritt’s two-stage pressure leach process (Collins et al., 1994; Collins et al., 1995; Barth et al., 1998; Shairp et al., 2006). Pressure leaching replaced the original roastleach- electrowinning process in 1993.Filtration for the second-stage (HAL) leach residue originally consisted of two stages of vacuum drum filtration with intermediate cake repulping stirred tanks. As part of Hudbay’s 777 Project, with a designed increase in cast zinc production, a pre-feasibility study by SNC-Lavalin Inc. showed that losses of soluble zinc in the zinc pressure leach residue could be reduced by installing more efficient filtering and washing equipment. Based on laboratory performance, capital cost, installation ability, and potential operating cost savings, a 70 m2 Filtres Phillipe belt filter was chosen for the HAL residue, and commissioned in 2000/2001.When the HAL belt filter is performing well, there is no pooling of water on the surface, moisture content is relatively low, and subsequent analysis shows that water soluble zinc content is relatively low. There have been occasions where the filter has performed poorly with respect to the aforementioned parameters. Aside from the filter experiencing mechanical difficulties, there are several variables affecting leach residue filtration:"

Jan 1, 2012

By A. Sutherland Brown

"The Red Rose Mine is in the Rocher Deboule Range, 8 miles south of Hazelton. The mill camp (elevation 4,000 feet) is on Red Rose Creek, 11 miles by road from Skeena Crossing. The mine camp is one mile northeast and 1,600 feet above the mill camp on a spur of Red Rose Peak.The Red Rose mine was described in the Jubilee Volume, Structural Geology of Canadian Ore Deposits (Davis, pp. 129-131), but regional geology and mine development have progressed to a stage at which a more complete description is possible.The property was first located in 1912, and for the next 7 years was prospected actively for gold and copper on the southern extension of the Red Rose shear. Scheelite was first discovered in the vein in the northern part of the shear in 1923. The Consolidated Mining and Smelting Company of Canada, Limited optioned the property in 1939, and after a drilling program in 1940 the present mine development was initiated in the vein in the northern part of the shear. A 75-ton-per-day mill started operating early in 1942 and continued until 1943. The property was inactive until 195 l, when Western Tungsten Copper Mines Limited leased the property from The Consolidated Mining and Smelting Company of Canada, Limited. A mill, which later was enlarged to 140 tons per day, started operations at the end of 1951. The mine and mill were closed in December, 1954.The mine has twelve levels and sub1evels, and most of the workings are in the plane of the vein (see Figure 2a). The level interval is not constant, but between the lower four levels is 87 feet (100 feet in the plane of the vein). Access is provided by four adits; the 800 (elevation 5,659 feet), 600 (5,920 feet), 300 (6, 133 feet) and 200 levels (6,237 feet). The 600 level is the main haulage, and from it the ore is transported to the mill by aerial tram. From this level an inclined shaft extends in the vein to the lowest level (I, 100)."

Jan 1, 1949

By David E. Pearson

"There are many tests that can be used to characterize and classify coals, and describe their quality. One of the easier tests, and most versatile in its application, is petrography. Rank and coal type are precisely defined by petrographic evaluation, and in this paper they are compared with other definitions of rank and coal type. Brief descriptions are given of the various rank tests, and of rheological and coking tests used to describe coking-coal quality in Canada. Similarly, tests used to evaluate thermal coal quality are discussed. Finally, the use of these tests as parameters to classify Canadian coals is examined with reference to four coal classifications.Introduction Among all coals there are two independent variables that are required to evaluate coal quality. These are, coal rank and coal type (or composition), and although coal petrography can be used to precisely define them, other methods are often used to provide values that are, in fact, functions of rank and coal type. For example, volatile matter yield is used as a proxy for rank, and free swelling index is used as a proxy for coal type in the International Classification of Hard Coals by type. Currently, there are a number of methods in use in Canada to define rank. The approach taken here, (obviously the author's bias), is that Romax, the mean maximum reflectance of vitrinite, is both a quick and an accurate measure of rank. It is logical to compare the other techniques employed in the measurement of rank to this favoured method. Coal type is, in theory at least, simply a quantitative measure of the various varieties of coal. In practice, the microscopic entities are assigned to a Reactive or Inert category, and at that point objectivity fades from petrography. Despite this somewhat subjective approach, petrographic composition of coals remains an independent variable of such.importance that its place in the evaluation of coal is essential. In this paper, a variety of me.thods that are used to assess rank and coal type are reviewed and compared; the influence of these variables over other parameters that are used to determine the quality of metallurgical and thermal coals is examined, and their usefulness in coal classifications is discussed."

Jan 1, 1985

By J H. Dressel, J. E. Williams

This paper presents a brief review of what coal gasification is, procedures that are available today and processes that may be available in the future. Examples are given as to how the process might be used in power plant applications, the effect on pollution level and power costs, and some thoughts on the added burden that might be placed on mining and coal preparation.

Jan 1, 1973

By C. Pichler, C. Benigni, J. Antrekowitsch

"The recycling of steel mill dust results in zinc oxides which are sold to the primary industry in or-der to recover zinc in its metallic form. Due to the contained impurities - chlorine and fluorine - these sec-ondary oxides are usually charged into the roaster together with primary concentrates. Appearing problems in this furnace limit the application of secondary materials. Based on the zinc amount, a direct leaching, assumed that a low halide concentration is present, would be possible. To use the zinc solution directly in the electrowinning stage, the concentration of impurities, first of all iron, is limited. Iron can be found in secondary zinc oxides due to carry over during the recycling process. In order to reduce the iron content in the solution, the leaching has to be pH-controlled. This leads to a limited number of simple purification steps before the solution enters the electrolysis. Various trials were performed to evaluate the influence of temperature, time and sulphuric acid concentration on the iron dissolution. This paper deals with the results and also focuses on other impurities such as halides. Additionally, the soda washing process, usually done with secondary zinc oxides to remove most of the halides, and the challenges within this step are discussed.INTRODUCTION Recycling of steel mill dust, which is the main zinc containing residue, in the Waelz process dis-plays the common method worldwide. The product of the process is a secondary zinc oxide which is con-taminated with different elements like lead, iron and halides due to mechanical carry over or evaporation. Depending on the feeding material the concentration of each element in the dust is varying. The zinc con-tent of the product, also called Waelz oxide, lies around 65–68%. Based on these values it presents an al-ternative to the primary concentrate for the production of metallic zinc. The contained halides limit the direct utilization in the leaching stage and therefore have to be reduced. State of the art is a soda washing process but also solvent extraction gives a possibility to remove chlorine and fluorine but the desired con-centration for the electrolysis is hardly reachable (Antrekowitsch et al., 2016) Iron is present as an undesirable component of such secondary zinc oxides due to carry over. During the hot acidic leaching of the secondary concentrate, iron is dissolved too. Based on the higher electrical potential iron has to be removed before the zinc solution enters the electrowinning stage. It is usually removed by precipitation as goethite, hematite or jarosite, which is the common precipitation residue (Ismael et al., 2003)."

Jan 1, 2017

By François Robert

"The Eastern Abitibi Sub province (Quebec segment), contains two main types of gold deposits: the common quartz-vein type and the rare pyritic type. Both occur in areas dominated by volcanic rocks and are spatially associated with major fault zones.Quartz-vein gold deposits consist of simple to complex networks of quartz-carbonate-pyrite veins in reverse shear zones and extensional fractures. They occur in areas dominated by mafic volcanic rocks and are commonly associated with small syn- to late-tectonic porphyritic felsic intrusions. Associated alteration, which postdates peak metamorphism, is dominated by carbonatization, sericitization and pyritization of the wallrocks. These deposits formed late in the geologicalevolution of the Abitibi.Pyritic gold deposits range from deformed massive sulphide lenses to zones of syntectonic pyrite-rich veinlets and associated pyrite disseminations. These deposits occur in environments dominated by felsic volcanic rocks that are typically converted to sericite schists near the deposits. The associated pre-metamorphic aluminous alteration is now characterized by metamorphic sericite, andalusite, kyanite and chloritoid, overprinted by a late retrogression of alumino- silicates. These deposits probably represent deformed volcanogenic massive sulphide deposits, but the timing of gold introduction in these is not fully understood.The differences in geological attributes reflect significant differences in the genesis these deposits: the pyritic deposits probably have a multistage genesis, including a pre-tectonic stage, in contrast to a single stage late-tectonic genesis for the quartz-vein deposits.RESUMELa partie Est de la Sous-Province de l’Abitibi( segment québécois) renferme deux types de gites d' or: ceux de type ""veine de quartz"" et ceux, plus rares, de type ""pyriteux"". Ces deux types se trouvent dans des secteurs particulièrement riches en roches volcaniques et mantrent une association spatiale avec des zones de failles majeures.Les gites de type ""veine de quartz"" correspondent à des réseaux de complexité variable de veines de quartz-carbonate-pyrite se développant dans des zones de cisaillement inverse et des fractures de tension. Ils se concentrent dans les régions dominées par des roches volcaniques mafiques et s’associent fréquemment à de petites intrusions porphyriques felsiques syn- a tardi-tectoniques. L’altération associée ace type de glte est postérieure à la phase majeure du métamorphisme et consiste en une carbonatisation, une sericitisation et une pyritisation des épontes. La mise en place de ces gites est tardive par rapport à l'évolution géologique de l'Abitibi.Les gites d' or de type pyriteux consistent en des lentilles de sulfures massifs déformes, des zones d' abondantes veinules pyrite uses syntectoniques, et des zones de pyrite disséminée. Ces gites se retrouvent dans des empilements contenant surtout des roches volcaniques felsiques qui sont transformées en schiste à séricine pres des gisements. L’altération a l’umineuse pre-metamorphique associée a ce type de glte a donné naissance, lors du metamorphisme regional, a la sericite, a 'andal ousite, a Ia lcyanite et au chloritoi""de; par la suite, les alumino-silicates ont été affectes par une alteration retrograde tardive. Ces gites representent probablement des depOts de sulfures massifs volcan gènes déformes, mais la chronologie de la mise en place de l'or dans ceux-ci est encore mal comprise.Les caractéristiques géologiques propres à chacun de ces types de gites reflètent des conditions de formation différentes: le type ""pyriteux"" montre une histoire génétique polyphasée, incluant une étape pre-tectonique alors que le type ""veine de quartz"" s’est développe au cours d’une seule phase tardi-tectonique."

Jan 1, 1990

By R. A. Campbell

Pig iron and silicospiegeleisen were produced experimentally from a very low-grade manganiferous iron ore from Steep Rock, Ontario, by a two-stage electric smelting process. The most favourruble operating conditions were determined for each stage. Cement clinker then was made by calcining the slag from the second stage of smelting, with additional limestone and alumina. (This slag would normally be a waste material). The cement clinker produced had the composition of commercial Portland cement, and met the physical test requirements of the Canadian Standards Association Specification A5-1951 for normal Portland cement as well as could be expected for a material produced on .such a small scale.

Jan 1, 1958

By R. Elliott, C. A. Pickles, J. Peacey

As the nickel sulfide ore deposits become decreasingly viable as a source of nickel metal, increasing attention is being paid to the exploitation of the nickeliferous laterite ores. Attempts to produce a high grade ferronickel concentrate from these ores by pyrometallurgical methods face several challenges, in particular the selective recovery of the highly disseminated nickel from the reduced ore. The current work explores strategies for maximizing the size of ferronickel particles formed in order to improve the selective recovery of the ferronickel by magnetic separation. The effect of various coal, elemental sulphur, pyrite and sodium sulphate additions on ferronickel particle formation and size at 1000°C have been investigated. It has been observed that increased coal additions leads to a moderate improvement in the size of the ferronickel particles, while the presence of any sulphur bearing reagent leads to a significant increase in particle size. The retention of sulphur in the reduced material has also been studied, showing sodium sulphate has the highest retention, followed by pyrite and then elemental sulphur. An inverse trend was observed in the efficiency of sulphur retention on the basis of residual mass of sulphur per unit mass of reagent added.

Jan 1, 2015

By Allan J. Guse

The primary limiting factor for hoisting capacity from great depths is the self-weight of the typical steel wire ropes used for mine hoisting. Steel wire ropes possess properties making them very suitable for mine hoisting including high strength and durability, but have the negative characteristic of being relatively heavy in comparison with their strength. Also, as hoisting depths increase, the service life of steel wire ropes decreases due to the higher stresses and physical effects on the ropes. The significantly higher strength-to-weight ratio of synthetic ropes compared with steel ropes offers the primary advantage of hoisting a larger payload with a similar size rope and hoisting plant. The beneficial properties of synthetic ropes could be used to improve the overall economics of deep underground mining both for new deep shaft projects and for existing mining operations expanding to deeper orebodies. A research and development program has been initiated to evaluate the suitability of a fully synthetic rope for the mine hoisting application, including rope discard methodology and NDT testing. The three phases/projects are: 1) proof of concept with focus on coilability under load (successfully completed in 2012); 2) high speed and load durability optimization & NDT Development; and 3) in-situ mine trial.

May 1, 2013

Flotation works very well for particles that are typically in the range 20 to 150 µmin diameter, for base metal ores. In this range, it is possible to get quite high recoveries in conventional flotation machines. Outside this range, the recoveries decline progressively, whether it be with the very fine or the coarse end of the size spectrum. In this paper, the reasons for the drop-off in recovery are briefly reviewed, together with strategies for future work. Recent progress in the author's laboratory will be described. These include the Concorde Cell, which takes advantage of the high dissipation rates in the shock wave created when a gas-liquid mixture reaches supersonic velocities. The environment thus created is very beneficial for the flotation of ultrafines. For coarse particles, the reasons for the drop-off in recovery can be related to the highly turbulent nature of the pulp in a conventional flotation cell. To improve recovery, it is necessary to find a way of bringing particles and bubbles into contact in a quiescent environment. A new process for coarse particle flotation will be described, in which a fluidized bed is created in the flotation cell. The flow conditions are very gentle, and the high solids concentration leads to rapid rates of capture of the particles. Experimental results are presented. It is apparent that the maximum floatable size for coal and minerals can be increased by a factor often over the limits found in current practice. Advances

Jan 1, 2009

By Celine Y. Zhang, Chloe J. Feng, Charles Q. Jia, Donald W. Kirk

Oil sands petroleum coke (OSPC) is a by-product of coking - a high-temperature process that converts the mined bitumen to the synthetic crude oil (SCO). For every barrel of the SCO produced, about 20 kg of OSPC are generated. Over 70 million metric tons of OSPC have been produced and stockpiled as a result of the development of oil sands industry in the past few decades. Unlike conventional petroleum coke, OSPC has uniquely high impurity contents, particularly sulphur (~ 7 wt%) and metals (e.g. vanadium at ~0.15 wt%), which has hindered its large-scale applications as a solid fuel. Vanadium is a valuable metal that is widely used as an alloy for strengthening steels. The stockpiled OSPC contains about 100,000 tons of vanadium, while the world’s production in 2013 was only 75,600 tons. At the current price of $25US/kg, the OSPC-bound vanadium represents a total value of $2.5 billion US dollars. In this work, we investigate the technical feasibility of extracting vanadium from OSPC. The work focuses on the characterization of vanadium in OSPC and the conditions for effective extraction of vanadium from the OSPC.

Jan 1, 2015

By J. Basi, D. F. Rucker

"A review of historic operating practices of the heap leach pads at the Los Filos Mine, Mexico, revealed periods of restricted cyanide addition, reduced leach time, and insufficient irrigation flow. These issues all led to the buildup of partially leached recoverable gold inventory within the leach pads. Drawing down this inventory represented an opportunity to bring value forward. This paper outlines the strategic initiatives which were implemented as efforts to accelerate the inventory drawdown, including geophysical mapping and pressure injection.INTRODUCTION Los Filos is a heap-leach operation located in the Guerrero gold belt in southern Mexico. Operational and hydraulic challenges at the Los Filos Mine have led to a buildup of gold in inventory within the leach pads. Operationally, periods of restricted reagent addition, reduced leach time, and insufficient irrigation flow have compounded over the last eight years, and resulted in significant inventory growth. Hydraulically, the leach pad has issues with low permeability and solution channeling due to the fines and clay content of the ore. The leach pad is storing high-grade pregnant leach solution (PLS) as perched aquifers above areas that are compacted and difficult to drain. These operational and hydraulic challenges made it particularly difficult to spatially predict the precise locations of the inventory build-up. Fortunately, the challenges at Los Filos are not unique to the mine, and others have taken steps elsewhere to reduce metal inventory through a program that targets areas for inventory drawdown. For example, Ghorbani et al. (2016) noted that a method of injecting barren reagent solutions, applied directly to specific areas of a leach pad to reduce inventory, was presented by Wan and Brierley (1997) and Wan (1997). Seal (2004; 2007), Seal and Jung (2005), and Seal et al. (2012) have put the injection methodology into practice in Nevada and Colorado gold mines with a technology called Hydro-Jex®. The goal of Hydro-Jex has been to supply reagents at a high pressure over a short duration, followed by periodical low pressure rinse periods to remove leached metal and resupply fresh reagent to the ore."

Jan 1, 2017

By L. Tafaghodi, S. Sarbishei

"Following the depletion of nickel sulfide ores, laterites are considered as one of the main sources for producing nickel and cobalt. One of the primary steps in pyrometallurgical extraction of nickel from laterites involves partial reduction of the ore at temperatures below 1000°C. Studying the kinetics of laterite reduction provides valuable information on reducibility of nickel laterites using coal as a reductant. The present study investigates the reduction behavior of a nickel laterite by thermal gravimetric analysis and differential scanning calorimetry. Non-isothermal reduction tests and X-ray diffraction analysis were performed to find the main reactions that occur during the process. The kinetic parameters were calculated by Coats-Redfern method. The general model of simple reaction f(a)=(1-a)n was used for calculating kinetic parameters.INTRODUCTION Nickel (Ni) naturally occurs in the form of sulfide and laterite ores. Laterite ores are mainly available in tropical regions. Weathering phenomena during millions of years has led to the formation of several layers with specific mineralogy (Butt & Cluzel, 2013). The three main layers downward are limonite, smectite, and saprolite (Crundwell et al., 2011). Although laterites are the most available nickel ore resource (70%), their share in the overall Ni production is limited to 40% (Crundwell et al., 2011). The main reasons for not materializing the full potential of laterites are as follows (Ray et al., 1985): •,Laterite ores contain high water content (free and combined) which in turn results in high energy consumption of the extraction process. •,As Ni is present in the form of solid solution in laterites, physical upgrading methods such as flotation are not effective in increasing the Ni content before the extraction process. •,Extracting Ni from sulfide ores involve exothermic reactions which are beneficial due to decreasing the overall energy requirement of the process, however there is not efficient release of energy in the process of extracting Ni from laterite ores."

Jan 1, 2017

By R. M. Lauer

OVER THE YEARS concentration of the Sullivan ore has become progressively more difficult as the ore has become increasingly refractory. The introduction of new reagents and changes in the flow of the concentrator have been and continue to be necessary in order to maintain and improve the efficiency of metal extraction. Prior to the completion of the pilot mill in 1957 ail new ideas were developed in laboratory equipment. If these were found to be promising, there was no alternative but to introduce them directly to the main mill flow in one step. When a major change was involved there was always the possibility of serious losses while the mill was being adjusted to the changed conditions. It proved difficult to determine whether these losses were the result of the changed procedure or of failure to adjust the flow to a change in the condition of the ore during the test. The pilot mill has provided a valuable intermediate step between the laboratory and the mill. It avoids the losses which occurred when unsuccessful full-scale tests were attempted, and conversely it provides assurance that full-scale flow changes can be made without serious hazard.

Jan 1, 1960

By Zihe Ren, Edouard Asselin, Marcus Tomlinson, Tianbi Zhang, Jing Liu

"Raman spectroscopy is used to quantify the extent of disorder in the carbonaceous matter associated with preg-robbing ores. Previous studies of Goldstrike ores showed that the height and width of the peaks for the “D” (disordered) and “G” (graphite) bands, the so-called “Raman ratio” had a strong correlation to the preg-robbing value (PRV) measured for various ore samples. A brief literature review on Raman spectroscopy as it applies to preg-robbing ores is presented. Further, recent studies, presented here, have shown no correlation between the Raman ratio and the PRV for a wide variety of ores. This suggests that the extent of organic carbon crystal disorder is not the main factor in determining preg-robbing characteristics.INTRODUCTION Valuable base metals, such as nickel, cobalt, molybdenum, vanadium and tungsten, are used in a wide range of important technological applications. The demand for many of these metals has increased significantly over the last few decades, driven especially by economic expansion in Asia generally and China in particular. This has led in turn to a large growth in the output of mines in order to satisfy this increasing demand, as shown by the data in Table 1 (USGS, 1994, 2014). These data reflect an even longer trend of growth of these metals, with nickel, for example, showing an average rate of 5.3% per year from 1980 until 2015 (International Nickel Study Group, 2017). This rapid and sustained rate of growth means that annual mine outputs for nickel, tungsten, molybdenum and vanadium have had to double roughly every 11 to 14 years, whilst cobalt mine output has had to double roughly every 7 years, over the period from 1994 until 2014. With the average working life of a nickel mine being between 17 and 22 years (Statista, 2017), this means that from the time a nickel mine opens until it closes, the industry needs to find the equivalent of another three or four mines of a similar output to satisfy this relentless growth in demand for the metal."

Jan 1, 2017

By Jonathan Peck, Carl Hendricks

"Global Positioning Satellite (GPS) based positioning and navigation systems have been recently developed and implemented by AQUILA Mining Systems Ltd. on blast hole drills and electric cable shovels in Canadian open pit coal and iron ore mines. These systems enable the location of the drill bit or the shovel tracks to be accurately determined in three dimensions. The position of the drill or shovel is displayed to the operator via a real-time, Moving Map Display (MMD) on an LCD-VGA screen. The MMD allows the operator to accurately navigate the drill from blast hole to blast hole or maintain a desired shovel grade or face position, with respect to displayed bench features. The maps for the MMD are downloaded from the mine office via laptop or radio link as required or as mining plans change.To obtain reliable, accurate and real-time3D positions of mobile mining equipment, proven GPS technology has to be utilized. The GPS components need to operate reliably under the severe environmental conditions that exist on board mobile mining equipment. In addition, they have to contend with varying pit geometry’s and satellite configurations, with little or no performance degradation. These issues were initially examined in December1993 during a feasibility project between AQUILA and Gregg River Resources Ltd., in relation to implementing GPS systems on blast-hole drills.To achieve certain design objectives, AQUILA Mining Systems Ltd. has developed navigation systems for cable shovels and blast-hole drills based around off-the-shelf, high precision GPS components. These systems utilize the AQUILA Advanced Monitoring Platform (AMP), to display graphically, via the MMD, shovel grade and drill position to the operator to within ±12 inches of design coordinates. Production prototypes have been installed on a Marion 301 cable shovel and a Bucyrus-Erie49-R Series III drill at the Fording River Mine in August, 1995, at the Wabush Mine on a Bucyrus Erie 190-B shovel in June, 1995, and on a GD120 drill at Gregg River Resources Ltd. in January, 1996. All these systems have undergone field trials to test system components and functionality’s under actual production conditions. This paper will discuss these GPS-based positioning and navigation systems in subsequent sections."

Jan 1, 1997

By James McManus

The original analogue instrumentation at Lornex Mining Corporation to optimize the throughput by controlling the power drawn by the semi-autogenous mills was found to be inadequate because of the frequent changes in ore type. Although the trunnion bearing pressure of the mill was a crucial control criterion, it was not utilized in the original control scheme. After several plant tests of different types of analogue controllers were unsuccessful in finding any control equipment suitable for this application, it was concluded that a digital process control computer was required. Computer control strategy to optimize the grinding rate by controlling the power and the bearing pressure of the semi-autogenous mill was developed and a Fox 2 /30 computer made by Foxboro was selected. After six months of experimentation, it was found that the throughput was increased substantially by computer control.

Jan 1, 1978