Search Documents

By R. Holmestad, M. Gazizov, S. Wenner, R. Kaibyshev, J. K. Sunde

"Mechanical properties and microstructure of an Al-4.7Cu-0.74Mg-0.51Si-0.48Mn-0.10Cr-0.09Ti-0.02Fe (wt. %) alloy subjected to various thermomechanical processing (TMP) have been investigated and compared to conventional ageing at 170°C (designated T6). Three TMP routes involving cold deformation of solution treated samples were tested. These were (i) 3%-stretching (T8-3%), (ii) equal-channel angular pressing (ECAP) to true strain (e) of ~1 (T8-1) and (iii) ECAP to e~2 (T8-2), all with subsequent ageing at 170°C for 0-96 h. At peak age conditions, both yield stress, ultimate tensile strength and elongation-to-fracture decreased for the T8-3% state as compared to the T6 condition. Intermediate ECAP (T8-1 and T8-2) lead to significant increase in maximum yield stress, ultimate tensile strength and elongation-to-fracture. The changes in mechanical properties were related to microstructure evolution, encompassing changes in grain sizes, dislocation densities, precipitate morphology and phase fractions, which were characterised using transmission electron microscopy. Relations between TMP, precipitation behavior and contributions to different strengthening mechanisms are evaluated.INTRODUCTION Al-Cu-Mg-Si alloys are widely used as structural materials in aerospace industry due to their attractive combination of high specific strength, good fracture toughness and enhanced creep resistance. These properties are largely due to the formation of a large number of nano-sized metastable precipitates during artificial ageing (Polmear, 2006; Eskin, 2003; Gazizov, Dubina, Zhemchuzhnikova, & Kaibyshev, 2015). The precipitation behaviour in these alloys is complicated and depends among other things on Cu concentration and the Mg:Si ratio (Wolverton, 2001; Chakrabarti, & Laughlin, 2004). In general, the precipitation sequence has been presented in a prior study (Eskin, 2003) as follows:"

Jan 1, 2018

By S Grönstrand, C. Perez, A. B. Yañez, F. Coddou, P. Morales, H. Elgueta

"The TankCell® 300 forced air flotation cell designed and built by Outotec, with active volume of over 300 m3, was installed at Codelco’s Chuquicamata concentrator in September 2008. After that, a program was conducted, where the new cell was tested against the plant’s existing flotation cells of type TankCell® 160, with an active volume of over 160 cubic meters.Testing program was exhaustive and detailed. Grade-recovery curves for each setup were reported, along with recoveries by particle size. Secondly, operational characteristics like air feed and froth height setpoints, and power consumption are compared side-by-side. As the third topic, gas dispersion characterization included velocity mapping, holdup, bubble size and bubble surface area flux operating range. The fourth area of interest was the retention time distribution (RTD) of the 300 and 160 m3 cells in comparison. A detailed campaign using radioactive tracer tests was conducted to clarify this.All of the investigations mentioned above are reported in separate papers for more detail. The aim of this paper is to collect the key findings, and present them in real terms, always referring to operability and metallurgy of the cells. It is destined for people designing new plants and to those improving and expanding existing ones. The most frequently heard question is: will the new large cells operate at same efficiency as the smaller ones. In short, the answer is: NO. They operate at improved efficiency!INTRODUCTIONIn the last two decades of minerals processing, there have been three dominant trends of development in the flotation technology: equipment scale-up, cell characterization and circuit modeling. Equipment scale-up has been rapid in the past two decades. In the year 1990, the largest flotation cell in use was 50 cubic meters of size. This year, 300 cubic meters is the largest installed cell. Characterization of flotation equipment and circuits is a very popular subject nowadays and has helped many operations to improve their recoveries through better control strategies, for example by using optimized air feed and level control profiles (Gorain, 2005), (Doucet, Gomez, Finch, 2006), or through better maintenance (Coleman, Urtubia, Alexander, 2006). Characterization work is closely linked to circuit modeling. The aim is to produce sufficient amount of data to allow reliable model building. These models are then used to design new circuits and to improve existing ones. So in summary, these three lines of development have slightly different aims – from capital and operational cost to performance optimization. Ultimately, they converge in the same end result – maximizing the profitability of the operation. Following chapters will summarize the extensive test work and scientific studies at Codelco Chuquicamata. The aim was to compare a TankCell® 300 cell, with nominal volume of 300 m3, against two TankCell® 160 machines, with 160 m3 volume in each. The work should yield answers to questions: does the larger cell produce similar results – is the scale-up successful?"

Jan 1, 2010

By D. E. Gill, A. Piche, S. Dufresne

"SOMMAIREUne méthodologie de prévision des coûuts de forage en galeries est proposée. Cette méthodologie a été élaborée pour les perforatrices pneumatiques manuelles. Elle est composée de quatre modèles: (1) un modèle de pénétration conduisant à la prévision du temps de forage; (2) un modèle d'estimation de la durée de vie des fournitures; (3) un modèle d'estimation de fa quantité d'énergie consommée; et (4) un modèle de calcul de couts. Elle fait intervenir la résistance en compression uniaxiale de la roche du massif foré, le diamètre des trous, Ie type de perforatrice utilise, fa pression d'air d'opération, la longueur des fleurets, les temps morts associes au forage ainsi que le rendement des compresseurs, des perforatrices et du réseau de distribution de l’air comprime. L 'application de la méthodologie est illustrée à l’'aide d'un exemple, suivi d'une courte analyse de sensibilité et d'une brève discussion. ABSTRACTA drilling cost estimation methodology for underground headings is described. This methodology has been developed for percussive hand-held drills. It comprises four models: (1) a drillability model used for the prediction of the drilling period; (2) a model for the prediction of bit and rod lives; (3) an energy model; and (4) a cost model. It makes use of the uniaxial compressive strength ofthe rock drilled, hole diameter, drill type used, operating air pressure, drilling rod length, dead times that may occur during the drilling operation as well as compressor, air distribution network and drilling machine efficiencies. The application of the methodology is illustrated with an example, followed by a short sensitivity analysis and brief discussion."

Jan 1, 1994

By J. Dong

"A “green” collector project has been initiated at Vale Base Metals Technology Development to replace xanthate. Bench and miniplant testwork showed comparable metallurgical results between xanthate and DTC (sodium dibutyl dithiocarbamate), a “greener” collector. During the first DTC plant trial, a strong interaction between the process water and DTC negatively impacted the metallurgy. The subsequent investigation showed that the quality of process water including suspended solids and dissolved metal ions had a significant impact on the performance with DTC, while less so with PAX. This paper explains these differences using UV spectrophotometry and batch flotation tests. INTRODUCTIONVale Base Metals is dedicated to sustainable mining and mineral processing. One of the key activities is to find a “greener” collector to replace xanthate (PAX: potassium amyl xanthate), which decomposes during storage and flotation causing CS2 emissions in the work place. As the most promising candidate, DTC (sodium dibutyl dithiocarbamate) was evaluated in the lab and miniplant (Dong & Xu, 2011). Consequently, a plant trial was conducted in the winter of 2010. However, the results were not as good as expected. The subsequent investigation showed that the quality of process water played a significant role in the metallurgical performance with DTC but less so with xanthate.From test work in 1996 and 1997, a series of batch tests were performed at Clarabelle Mill to investigate the winter/summer metallurgical shift with xanthate. As shown in Figure 1, the winter metallurgy was considerably worse than the summer metallurgy (Xu & Wilson, 2000). At 80% pentlandite recovery, the concentrate (Cu+Ni) grade was 21% in the winter and 26% in the summer. At 23% (Cu+Ni) concentrate grade, pentlandite recovery was 85% in the summer and 70% in the winter. In the summer, the process water is much cleaner, with very low concentrations of dissolved metals ions and suspended solids; while in the winter, the water is yellow and cloudy, with much higher suspended solids. Based on these results, it was concluded that the process water in winter has a detrimental impact on metallurgy."

Jan 1, 2012

By J. A. Finch

Individual mineral cyclone performance curves were determined for the four major minerals at two lead-zinc concentrators. Sizing was by screen and cyclosizer down to approximately 10 um, with lead , zinc and iron as saying of each size fraction. The performance curves were similar in shape and located according to the mineral specific gravity, Pm. The curves displayed a discontinuity at the fine end and a magnitude of short-circuiting of fines to the underflow which increased with Pm. Mass fraction of water to the underflow was only a guide to this short-circuiting. Sharpness of separation seemed in dependent of Pm. An inflection in the over-all performance curve was shown to be a consequence of the individual component mineral performance. A general relationship was observed showing that the flow regime of classification changed from laminar/ intermediate to turbulent with increasing cyclone feed size. Individual mineral size reduction for the four major minerals at one of the concentrators was also determined. Size reduction of the silica was greater than that of the galena, in contradiction to their accepted relative grind-ability. The observation did correlate with silica being much coarser than the galena in the feed to the ball mill. It is suggested that the silica acted as a buffer to the galena.

Jan 1, 1977

By CH. Liu, H. X. Jiang, X. Xiao

"A study has been conducted to characterize the fatigue life in 7050-T7451 thick plate by the comparison between an experimental alloy and commercial alloy. The fracture origins were specified and their sizes were measured by scanning electron microscope (SEM). Additionally, the size, number density and spatial distribution of porosity in the experimental material and commercial material were characterized and compared, using X-ray Computed Tomography(XCT). The results showed that microporosity was the predominant site for crack nucleation and subsequent failure of the experimental alloy. However, as for the commercial alloy, fatigue cracks were found to originate from constituent particles. The presence of microporosity in 7050-T7451 thick plate reduced fatigue life of an order of magnitude or more compared to the commercial alloy. The relationships between size of origin and fatigue life were proposed. It was showed that the fatigue endurance was reduced when the size of porosity increased.INTRODUCTION 7xxx series aluminum alloys, due to their combination of high strength, high resistance to stress corrosion cracking, and good fracture toughness, are widely used in structural engineering applications where high-strength and low-density characteristics are fundamental design requirements (Williams& Starke, 2003). Every designer is striving to find an optimal combination of properties including strength, corrosion resistance and fatigue resistance (Wanget al., 2016). Based on the design principles of aircraft, a higher fatigue resistance of aluminum alloys are required. Thus, many investigations have been carried out on the microstructures and its effect on fatigue properties of the 7xxx series aluminum alloy (Robson, 2004; Schubbe, 2009).Microporosity, which is a common defect in casting materials, can lead to a significant deterioration of mechanical performance and fatigue resistance, especially in the high alloyed 7xxx aluminum alloys. The actual valid loading area decreases due to microporosity, which results in detrimental effect on the mechanical properties. Many experimental studies have been conducted in this research field. Mayer et al.(2003) investigated the fatigue properties of magnesium alloys produced by high-pressure die-casting. The results show that porosity in magnesium alloys greater than0.18mm diameter may be considered as the most important material defect for high cycle fatigue and fully reversed loading conditions. Nadot et al.(2004) found that the near surface defects are much more dangerous than the internal defects. Wang et al.(2001a) used the Weibull statistics method to analysis the influence of the microporosity, oxides and particles on the A356-T6 alloy fatigue life. The results show that, the porosity is more detrimental to fatigue life than oxide films and particles. With regard to fatigue resistance, although the deleterious effect of microporosity has been generally acknowledged, a quantitative understanding between casting microporosity and fatigue life in 7050-T7451 plate is not well established."

Jan 1, 2018

By V. L. Gravitis

Radioisotope X -ray techniques of analysis for nickel have been tested in laboratory and plant trials. In the laboratory tests. a comparison was made of radioisotope and conventional analyses for nickel in solid s samples taken from streams of a nickel concentrator. Coefficients of variation of 1.7% for feed and concentrate samples , and equal to 10% for final tailing samples, were obtained. Continuous determination of nickel in final tailing slurries was demonstrated in a trial lasting 20 days at a nickel concentrator (Western Mining Corporation), nickel being determined with a standard error of 0.036% Ni in the slurry solids within the range of 0.24 to 0.68% Ni. This error, obtained by comparison of on-stream probe analyses with assays of samples taken from the stream, includes errors in sampling and assay by conventional techniques.

Jan 1, 1977

Reaction between xanthate ions in solution and oxidized compounds present on the surface of galena to form lead xanthate is considered to be a side reaction not contributing to flotation, although accounting for some consumption of reagent. The direct reaction of lead sulphide with xanthate and oxygen to form lead xanthate is the most significant to flotation. Coadsorntion of dixanthogen is also involved. Previous work has shown lead recovery in lead rougher flotation to be a function of m [H+] where: m = concentration of xanthate in solution rHl = hydrogen ion concentration. A plausible explanation for this relationship is suggest-ed. Likewise, the experimental findings that the amount of xanthate adsorbed under certain conditions is a function of m'[H+] are explained in terms of reaction between xanthate ions and soluble basic lead salts such as PbO.PbS04? It is also shown that m[H+] should have a constant value in lead cleaners operating at a higher pH than the roughers. This conclusion is confirmed by plant data, and the value of the constant agrees well with the calculated value. The finding is useful in mill control.

Jan 1, 1965

By S. Tavani, T. Rees

The current mining operations at Newmont Boddington Gold Mine (NBG) commenced in 2008, and commissioning of the processing plant started in the latter half of 2009. Metso Process Technology and Innovation were engaged to assist NBG with commissioning and project ramp-up through the implementation of a comprehensive “Mine-to-Mill” Process Integration and Optimisation project. This methodology entailed extensive data collection which included drill and blast audits, ore characterisation, comprehensive comminution circuit surveys and review of operational data to assess the limitations within the current mining and processing operations. The results of these investigations have been used to define the operating base line of both the mining and processing areas and identify improvement opportunities. The use of modelling and simulations, utilising actual production data, has allowed for multiple scenarios to be evaluated, minimising the requirement for actual trials and thereby minimising impact on the operation. Improvements implemented to date include: the introduction of routine rock strength measurement for inclusion in block models, modifications to blast design improving ROM fragmentation and downstream comminution process performance, and changes to improve performance of secondary crushing and grinding circuits. Close cooperation between the mine and plant personnel is playing a significant role in overcoming the challenges presented to this operation and further improvements are targeted for the second full year of process plant operation.

Jan 1, 2012

Eagle Plains Resources? Exploration in the Northern Cordillera ?Eagle Plains Resources Ltd. (EPL) is actively exploring for Zn-Pb deposits in the northern Cordillera in both carbonate-hosted and shale-hosted (sedex) environments. ?This presentation will review some of the significant carbonate-hosted Zn-Pb showings occurring in the Mackenzie Mountains, NWT and make limited comparisons with sedexdeposits in the adjacent Selwyn Basin.

May 1, 2006

By Warwick D. Bullen

Gold mining in the Yellowknife area of the Northwest Territories started long before the concept of sustainability entered the academic literature and by the time the term enjoyed widespread public acceptance, the Yellowknife gold mining industry was in its sunset years. Nevertheless, the city of Yellowknife will long outlive the gold mines that it was founded on, demonstrating that not only can mining build sustainable communities, but that sustainable mining as a concept is an entirely valid precept. To this effect, the authors examine the complex economic and social aspects of the gold mining industry in the Yellowknife area over the last 70 years.

May 1, 2004

By Andre Vien, D. H. Hendriks, D. Willet, B. C. Flintoff

"For many years the training of mill operators was an informal process which involved senior operators training junior operators on an as-needed basis. Recognizing the needs and benefits of better training some companies, and even some provinces through legislation, have moved to ensure that a formalized training program exists in the plants. These programs tend to focus on basic safety and operations. Much remains to be done. With the more rapid incorporation of new processing and information technologies, and the goal to keep labour costs to a minimum by doing more with less, operator training has become a critical issue. This paper briefly examines the evolution of training programs, provides some measure of their effectiveness, and explores some recent developments which could have a very significant impact on the industry.PreambleOne can draw an analogy between operator training and the mechanical support of production equipment. When we buy a piece of process equipment it is critical that the mechanical installation be done properly to ensure that the device will operate at peak performance on start-up. Once the equipment is running, some form of preventive maintenance is required to ensure continued efficient operation. The operators and the equipment are both elements of the processing system, yet the former do not seem to get the same ""start-up"" or ""operating"" support. Are they not seen as critical to efficient operation? Why is this so? What impact does it have? How can we improve?These are all very logical and important questions, although the answers are not nearly so obvious. In the mineral processing industry, progress in operator training over the past thirty years has been limited and quite variable. To address the perceived need for a more coherent and consistent approach, some provinces have moved to incorporate basic training requirements in their legislation. Some plants have gone a few steps further by building integrated training programs into their operating culture. One conclusion which can be easily reached is that there are no standards, and that the range of training activity is great. In other words, a flotation operator is not a flotation operator is not a flotation operator. Their knowledge and skills are very much a function of training and experience, which are clearly corporate and site specific."

Jan 1, 1994

By Descarreaux. Jean

"The Abitibi volcanic belt was sampled along a cross section extending from Matagami to a point east of Rouyn. A few samples were also collected in Louvicourt township, Quebec. The major elements were determined for 344 samples, and rock names were defined using normative minerals. The analytical data were studied by means of variation diagrams. The Abitibi volcanic belt is characterized by rocks belonging to both the tholeiitic and calc-alkaline magmatic series, but they show some differences as compared to some typical reference series, particularly those from Japan. Basalt is the predominant rock type and accounts for 44 per cent of the sampled outcrops. The volcanic rocks are relatively poor in K2O and TiO2. Regionally, the volcanogenic copper-zinc mineralization is associated with the calc-alkaline volcanic sequences. Locally, within such sequences, some types of abnormal deviations from the averages are recognized only in association with the copper-zinc mineralization. The anomalies are ascribed to hydrothermal alteration consisting of the introduction of MgO and removal of N a20; enrichment in K20 is also observed where zinc mineralization predominates. Examples of such anomalous zones show that, in places, this alteration phenomenon can be quite extensive. Petrochemical characteristics can be used as geochemical ore guides in exploration programs."

Jan 1, 1973

By R. K. Netolitzky

The Weedy Lake, Tower Lake, and Wedge Lake gold deposits illustrate contrasting styles and different ages of mineralization within the same district. The discovery of these deposits was the result of systematic exploration of gold occurrences noted during research of assessment files. The Weedy Lake and Tower Lake depo its reflect a late-stage gold mineralizing event. The e deposits developed along the same major structural break, and also display simi lar mineralogy and alteration patterns. Mineralization is developed in all the lithologies present. The Wedge Lake property, while having occurrences similar to the Weedy and Tower deposits. has the more important Twin Zone which best fits a volcanogenic exhalative model. The Twin Zone has a complex structural history without a recognizable alteration halo. The setting may be proximal to a hydrothermal vent. Mineralization is hosted within a mixed ulphide/oxide/silicate facies iron formation breccia. and the gold is intimately associated with arsenopyrite. The origin and age of the brecciation is key to understanding the mineralizing event. Traditional prospecting procedures in conjunction with conventional B-horizon soil geochemistry were instrumental in the Twin Zone and Weedy lake disco,•eries. Tower Lake was a prospecting discovery partially defined by previous drill programs. This deposit was also identified by B-horizon oil sampling.

Jan 1, 1986

By M. W. Mikhail, R. J. Mikula

"Funding has been made available through the National Energy Program to build a mobile fine coal treatment plant. The plant is intended f or field application and also to upgrade the existing pilot plant facilities.Western Canadian coals with high proportions of fines (due 10 their friability) cause high losses of fine coal to the reject and in turn reduce the over-all recovery of saleable coal. Eastern Canadian coals with high amounts of sulphur of ten require crushing to fin e sizes to liberate pyrite and therefore need effective and efficient separation of these fine sulphur particles. The difficulties involved in solving these problems are two-fold. One is the reluctance to experiment in an operating wash plant and the other is that laboratory scale testing often cannot be extrapolated to the plant environment. The mobile fine cleaning plant with its ability to operate at existing coal preparation plants across Canada and with its flexibility in implementing flowsheet option s and close monitoring of fine coal circuit variables, is ideally suited to solve these fine coal cleaning problems. The mobile plant objectives are to design and optimize flowsheets, evaluate and improve fine cleaning circuit operations and 10 lest new process monitoring and control equipment.The schedule for construction and the required resources will be outlined along with flowsheet options and the general R&D philosophy of the mobile plant.IntroductionIn relation to coal preparation technology, Canadian coal s can be grouped as Eastern coal, Rocky Mountain metallurgical coal and Foothills high volatile bituminous coal. The eastern coals have high sulphur contents and in some cases require crushing or even grinding to liberate the fine pyrite . Rocky Mountain metallurgical coals often occur in highly sheared seams which have been subjected to rapid coalification. The high friability of these coals means that degradation during mining, handling and processing is extensive and results in large amounts of fine s ranging between 20 and 60% by mass of the wash plant feed. The widely varying geo logical structure and exposure to the elements results in partially oxidized coals which perform inconsistently in the traditional method of fine cleaning by flotation . Foothills high volatile bituminous coals for thermal use are frequently interbedded with soft shales and bentonitic clays. These clays disintegrate during washing and swell, producing large volumes of tailings. The presence of clays in plant circuits, particularly fine circuits, tends to increase the viscosity and may cause deterioration of the fines density separation and increase magnetite losses. In view of the fact that fine coal cleaning is the most difficult aspect of coal preparation , a research program is being established to study the factors involved and to offer some solutions.A recent performance evaluation of Canadian washeries showed that yield losses in the minus 2 mm coal circuits were approximately ten times those occurring in the coarse coal circuits(1). Because 2 mm x 0 coal represents 30 to 70 per cent of the raw coal, these losses can be considerable . The operating and capital costs of beneficiating minus 6 mm coal are about four to five times higher than for plus 6 mm coal. In the case o f minus 2 mm coal the costs are even higher. The economic importance of the fine coal cleaning cannot be over emphasized and as a result, the CANMET R&D program is geared for fine coal beneficiation."

Jan 1, 1984

By M. Krasowska

Dynamics of collision and kinetics of the bubble attachment to hydrophobic solid plates (Teflon) of different surface roughness were investigated. The experiments were carried out in such a way that probability of the collision and probability that the detachment will not occur were equal always 100%. Thus, it was possible to determine effect of the surface roughness on the bubble attachment (three phase contact formation, TPC) only. A high-speed camera (1182 Hz) was used to record the velocity variations, bouncing and time of attachment of the bubble colliding with Teflon plates having different surface roughness (5 different plates). Roughness of the plate surfaces was modified in a mechanical way using different abrasive papers. It was found that the roughness had a crucial influence on the time-scale of the TPC formation and attachment of the bubble colliding with the Teflon plates. Despite high hydrophobicity of all plates (contact angles 1100 -115º) it was observed that at the smoothest surfaces (called "Teflon I" and "Teflon II" and having surface roughness below 1 um) there was no attachment during the bubble first collisions. Prior to the attachment four or more "approach?bouncing" cycles of the colliding bubble were observed there and simultaneously the bubble shape varied rapidly within time intervals below 0.85 ms. Time of contact of the colliding bubble with the Teflon plates was very short; 2-3 ms. These results indicate that during that short time of the collision the liquid layer separating the colliding bubble and the solid surface did not reach a critical thickness of its rupture.

Jan 1, 2006

By Jeanne B. Percival, Paul Ramaekers, Charles W. Jefferson, Pat A. Hunt, Eric G. Potter, Katherine E. Venance, William Davis, Sean A. Bosman

"A 10-cm thick clay-rich layer near the top of the Manitou Falls Formation of the Athabasca Group is unusual in its breccia texture, alteration, and detrital mineral composition relative to the adjacent overlying and underlying sedimentary beds. This layer is composed of angular quartz grains set in an illite >> kaolinite + dickite matrix. Deformed clay-rich fragments within the layer have very similar mineral assemblages. The presence of euhedral accessory minerals including Ti-oxides and aluminophosphatesulphate minerals points to a diagenetic/hydrothermal origin. The presence of individual grains of Kfeldspar and amphibole is unusual relative to the typical Athabasca quartz arenite; originally, these minerals were probably included in detrital quartz and subsequently liberated during fracturing. The textures and alteration characteristics suggest that this layer is a hydraulically-fractured unit, which has experienced hydrothermal fluid alteration - a possible pathway distally related to uranium mineralization Une couche argileuse de 10 cm d’epaisseur pres du sommet de la Formation de Manitou Falls du Groupe d'Athabasca est remarquable par sa texture brechique, son alteration et la composition de ses mineraux detritiques qui different de ceux des couches sedimentaires sus- et sous-jacente. Cette couche est composee de grains de quartz angulaires dans une matrice composee d’illite >> kaolinite + dickite. Des fragments deformes riches en argile dans cette couche presentent des assemblages mineraux tres similaires. La presence de mineraux accessoires idiomorphes dont des oxydes de titane et des aluminophosphates-sulphates suggere que ces derniers ont une origine diagenetique / hydrothermale. La presence de grains de feldspath-K et d'amphibole est inhabituelle comparativement aux arenites quartziques typiques de l’Athabasca; initialement, ces mineraux constituaient probablement des inclusions dans le quartz detritique qui ont ete subsequemment liberees pendant la fracturation. Les textures et les caracteristiques de l'alteration suggerent que cette unite a subi une fracturation hydraulique et a ete alteree par un fluide hydrothermal - possiblement en lien avec les effets distaux de mise en place de la mineralisation en l'uranium."

Jan 1, 2013

By M. Lindgren

"Hydrometallurgical processing involves process stages, like leaching, that create harsh environment for stainless steels. High acidity, the presence of chlorides and oxidizing ions combined with relatively high temperature create risk for both uniform and localized corrosion. Advanced electrochemical techniques were employed to study uniform and pitting corrosion of two stainless steel grades 316L and 2205. Results obtained with the linear polarization resistance technique combined with the harmonics distortion analysis, electrochemical noise and coupled multielectrode array systems are compared to the results of conventional electrochemical techniques and immersion tests.INTRODUCTIONHydrometallurgical processing has become favoured in metals production in recent years due to energy costs, leaner ore bodies and environmental factors. Because the hydrometallurgical processing route is flexible, various types of secondary raw materials, like flotation tailings, dusts, sludges and slimes can also be treated in addition to conventional mineral concentrates (Sarveswara Rao & Acharya, 2008).Hydrometallurgical processing relies on aqueous chemistry, usually acids, at temperatures around 100°C for the recovery of metals from ores, concentrates, recycled or residual materials. The processing route can typically be divided into three stages: leaching, solution concentration/purification and metal recovery. The processing environment is aggressive, especially in leaching. High acidity, relatively high temperature together with impurities, like chloride ions, place high demands on the corrosion resistance of construction materials. The dominant corrosion mechanism may be uniform corrosion or localized corrosion depending on the process conditions (Ekman & Torsner, 2010). This complicates the prediction of corrosion rates and, consequently, cost effective material selection.Traditional means to evaluate uniform corrosion resistance of stainless steels are immersion tests and the results are published in the form of iso-corrosion diagrams (Outokumpu Stainless, 2010). For the localized corrosion, namely pitting and crevice corrosion, immersion tests can be used but the duration of the test is rather long because an incubation period takes place prior to the occurrence of the actual localized corrosion damage. Electrochemical techniques, traditionally in the form of cyclic polarization scans, have been employed to assess the susceptibility of a material to pitting corrosion (Papavinasam, 2008). They cannot, however, give any indication of the pitting corrosion rate and lack potential for on-line measurements."

Jan 1, 2012

"The Australasian Joint Ore Reserves Committee (JORC), which is sponsored by the Australian mining industry and its professional organisations, developed the JORC Code to provide minimum standards for public reporting. JORC was first published in 1989 and later incorporated into the Listing Rules of the Australian and New Zealand Stock Exchanges making compliance mandatory for listing public companies in Australia and New Zealand."

Jan 1, 2003

By F. Charette

The paper reviews the requirements of the instrumentation required to monitor mining excavations in a high stress environment, and the development plan to instrument the D-Bolt in such a fashion as to be able to follow the behaviour of the bolts in relationship to the ground movements and support performance. Recent field observations of D-Bolts under static and dynamic conditions are also presented. Also discussed is the assumed mechanical behaviour of the D-Bolt. D-Bolts are used in two (2) Canadian underground mines operating in high stress environments and tested in three (3) other operations.

Jun 1, 2012