Search Documents

By Allan R. Punkkinen

Safe extraction of the valued ore resource in the deep levels of VALE Creighton Mine has progressed in a pillar-less fashion using vertical retreat, slot-slash and uppers retreat methods since the cessation of ?cut and fill? mining in the late 1980?s. Sequencing of the panel extraction and filling has been the key to successful exploitation of high stress orebodies at depth. In late 2010, discussions between the Operating Department and Creighton Ground Control revealed an opportunity to evaluate a trial primarysecondary sequence in the west end of the 400 Orebody at the 2340m horizon. To manage the trial primarysecondary project, a high level risk analysis and management of change was carried out to mitigate potential danger. As part of the requirements, an instrumentation project was conducted in the hanging wall and footwall bottomsills of the secondary panel and within the secondary panel itself. The extraction sequence was modeled with Map3D® software, confirming high stress levels with the advance of the primary panel. Enhanced ground support was installed based on modelling results. A key objective of the instrumentation project was to verify support system response to mining and to obtain knowledge in regards to the behavior of the stope. This paper describes the first time that this type of new innovative instrumented rockbolt technology had been used in a hard rock mining environment. Understanding of the physical deformation mechanisms of ground support in response to high stress conditions is the basis for an effective ground control strategy. The data played an important role in subsequent enhanced ground support system design at the mine and importantly, established the fact that the secondary pillar had not totally failed. Subsequent cavity monitor results helped establish that fact.

Jun 1, 2012

By P. R. La Pointe, J. Clark

"Studies have shown that the roof in coal mines is nearly twice as likely to fail at intersections as at entries due to enlarged roof spans, stress redistribution and other factors. However, the relative stability of intersections in a mine varies, and an improved understanding of what factors impact roof instability can lead to efficient, proactive mining practices that both enhance stability and mining efficiency.A study was undertaken at an underground longwall coal mine to develop a model to predict the stability at the intersections of entries and cross-cuts. The statistical analyses relied upon observational and measured data regarding the development of tension cracks, seepage, intersection geometry, mining practices, geological attributes and geomechanical factors at 783 intersections. Each intersection was given a NIOSH roof. Common data mining techniques, such as multivariate linear regression, multinomial logistic regression, decision trees and probabilistic neural nets, were considered and evaluated to establish correlations and associations between stability and the other variables. Two of the more successful techniques were Decision Trees and Multinomial Logistic Regression. The analyses showed that a number of factors impacted stability:• Overburden thickness (impact on stress concentration magnitudes)• Initial opening area (impact on stress concentration magnitudes)• Sulfur content (depositional environment & impact of mechanical properties, leaching effects)• Intersection type (impact on stress concentrations)• Gob distance (impact on stress concentrations)• Presence or proximity of a particular sandstone (impact on mechanical properties)• Roof bolt type and diameter (impact on reinforcement)Some factors showed no statistically significant relation to stability. These included:• Total area• Supported areaSeepage was a more problematic variable in assess. Seepage is associated with instability, but it is not clear whether seepage occurs as a consequence of instability, for example, through the creation of tension cracks, or whether the intersection has been excavated where water already exists and has degraded the rock prior to excavation, leading to greater instability.Seepage appears related to the geology of the roof rock mudstones, not the sandstones. Tension cracks in the intersections occur preferentially where the Sulfur content is below 0.9%. The Sulfur may relate to mechanical differences in the roof rock, and where the Sulfur is low, the roof is less stable, there are more tension cracks, and seepage is greater. This suggests that the weaker mudstones may be more prone the development of tension cracks, not because these rocks are more brittle, but possibly weaker.2-way and 3-way intersections appear to have less seepage than 4-way, although very few intersections overall have any seepage. This is similar to the roof stability, in which the 2-way and 3-way are more stable. 2-way and 3-way intersections have fewer-than-expected tension cracks, while 4-way have more than expected. These results suggest that four-way intersections are weaker and more prone to tension crack development, also suggesting that increased seepage results from weaker roof conditions, rather than the converse. Thus seepage appears to be mostly a consequence of instability rather than a cause and is higher where there are 4-way intersections, mudstone geology and external loading factors like depth of cover and proximity to gob that promotes crack development. The study also indicated that a better understanding of the mudrock facies could reduce uncertainty."

Jan 1, 2015

By Philippe Poirier

Les parcs à résidus miniers représentent un risque environnemental qui nécessite une gestion adéquate. Suite à la publication du « Guide sur la gestion des parcs à résidus miniers » en septembre 1998, les membres de l?industrie minière ont appliqué les éléments de gestion du Guide, permettant ainsi une amélioration continue des opérations. En février 2000, l?industrie minière a indiqué le besoin d?établir des lignes directives plus spécifiques pour l?opération sécuritaire des parcs à résidus. Dans cette optique, l?Association Minière Canadienne a publié, en septembre 2002, un Guide pour l?exploitation, l?entretien et la surveillance (EES) des parcs à résidus miniers. Suite au développement du Guide et à son application sur plusieurs sites miniers, il apparaît que la mise en oeuvre d?un Manuel ESS des parcs à résidus miniers permet : ? d?établir les responsabilités des intervenants; ? de s?assurer que les critères d?opération sont appliqués; ? de mettre en oeuvre le plan de déposition des résidus et de gestion de l?eau; ? de rencontrer les normes et exigences environnementales; ? de définir un programme d?entretien et de surveillance des ouvrages; ? d?identifier les risques et de mettre en oeuvre un plan d?intervention d?urgence; de démontrer une opération diligente.

Nov 1, 2002

By J. Ran

"Hangingwall sloughing is the major cause of unplanned stope dilution in open stope mining. Understanding the hangingwall sloughing mechanism can guide the stope design in minimizing the unplanned dilution and improving muck size and therefore mining efficiency. Though the modified stability graph method may be adopted to assess the hangingwall stability, for mines where the hangingwall is inaccessible, the required parameters are difficult to define and some of the simple influential factors cannot be easily identified in this method to provide guidelines for stope design.This paper identifies the main modes of hangingwall sloughing in open stope mining based on detailed data collected from mined-out stopes and site observations, applies the voussoir beam notation to analysis of the hangingwall sloughing mechanism, compares the model analysis results with the collected stope data, and provides guidelines for stope design and model application. Finally, examples are given to demonstrate the time and support effects on hangingwall sloughing and stope dilution."

Jan 1, 2002

For the last few years, a new and innovative technique has been successfully used to determine refractory and castable thickness in various metallurgical vessels. The acousto ultrasonic-echo (AU-E) technique uses stress waves to detect metal penetration and delaminations within refractory linings. In addition, it is capable of measuring the thickness of refractory layers and build-up material. The inspection and measurements can be carried out while the furnace is in full operation. The present paper discusses the principles of the AU-E technique, and its advantages and limitations. A number of case studies are presented to demonstrate various capabilities of this new Non-Destructive Testing (NDT) technique.

Jan 1, 2005

By Warnett Kennedy

"GENUINE CONCERN for the environment is a built-in attitude of mind. If you do not have it by age 40 you probably never will. Some people speak the jargon of 'environment' and 'ecology' for political reasons, others because it feeds their need and bias toward attitudes of moral indignation or dissent. Others pay lip-service for purely business reasons. Complete reactionaries equate conservationists, ecologists and environmentalists as either 'commies' or 'pinkos'. Their real credo is the old saying, ""Where there's muck there's brass."" Those who have genuine concern for good environment are not only romantics like Thoreau but realists who sense the danger to our planet if human greed is rampant and unchallenged. The cities are in real trouble. Almost 75 per cent of the population already live in and around cities. Even mining men live in cities or bring up their children in the new 'instant' towns. The ecology of cities is the concern of all. Our distinguished guest Stewart Udall, in his book ""The-Quiet Crisis,"" quoted Thoreau in 1859 as having written ""each town should have a miniature wilderness park, a primitive forest of five hundred or a thousand acres where a stick should never be cut for fuel, a common possession forever."" Mr. Udall will be glad to know that this advice was taken in at least one instance known to me. I refer to Stanley Park in Vancouver. It is a primitive forest of 1000 acres right inside our small downtown peninsula. It remains unmanicured. This month we celebrated the completion of a seawall of 4%, miles along its perimeter. The construction of this wonderful walkway started in 1910. We are very, very proud of our park."

Jan 1, 1972

By C. Carrasco

Caletones Smelter, Division El Teniente of Codelco Chile, has used Teniente Converter (TC) as the only smelting unit since November 2000. The modernization project considered the shutdown of the last reverberatory furnace, the installation of the fourth Teniente Slag Cleaning Furnace, the installation of a new fluidized bed dryer and the modification of the concentrate injection system into TC. The modernization project and related investments allowed for the increase of the smelting capacity up to 1.25 million t of concentrate annually.Next stage of the smelter expansion in the year 2004 considered the increase of the smelting capacity up to 1.44 million t/year. The expansion required technology modernization and the installation of the new equipment, such as concentrate injection system, oxygen plant, fluidized bed dryer and storage bin. Currently the annual smelting capacity is about 1.35 million t of copper concentrate, being limited by sulphuric acid plant treatment capacity. This paper presents the technology and production evolution in the Caletones Smelter in the years 2000 - 2006, demonstrating the potential of development and competitiveness of Teniente Converter as world-wide recognized smelting/converting reactor.

Jan 1, 2007

By Seongki Lee

The purpose of this paper is to propose the real-time facility management system framework based on Building Information Model (BIM) and Web of Things. Latest IT such as BIM is rapidly spreading to architecture, civil engineering, engineering and maintenance with the aim of simplifying complex system in buildings and facilities, minimizing operation cost, providing high value services and advancing facility management. In particular, BIM-based management framework design to assist the development of sensor information operation system, which adds convenience to facility maintenance and management, has emerged as a key issue. To this end, this paper proposed conceptual framework for data warehouse, web service and interface that make up real-time facility management system. The paper also produced conceptual methodology on CoRE-based web service platform, mobile device, BIM and WSN mapping.

Aug 1, 2013

By Michael T. McCaffrey

The wide range of potential feed materials, process steps, and products in metallurgical facilities means that standard equipment might not be available to adequately meet the project technical and economic needs. Custom designed equipment should be considered only after rigorous research precludes purchasing standard equipment. However, the decision to use custom equipment introduces a new element of risk into the project. To manage the risk, custom equipment design should be developed through the same front end loading (FEL) phases as project development. If more than incremental development of custom equipment is required, appropriate test work or pilot trials are required to test key uncertainties. Important activities during custom equipment design include maintaining clearly defined performance objectives, conducting appropriate reviews, carefully crafting commercial and intellectual property agreements with design and fabrication partners, and assembling a multidisciplinary team with sufficient development expertise.

Jan 1, 2015

"The most widely used method for predicting the onset of continuous caving is Laubscher’s caving chart. A detailed examination of this method was undertaken which concluded that it had limitations which may impact on results, particularly when dealing with stronger rock masses that are outside current experience. These limitations relate to inadequate guidelines for adjustment factors to rock mass rating (RMR), concerns about the position on the chart of critical case history data, undocumented changes to the method and an inadequate number of data points to be confident of stability boundaries.A review was undertaken on the application and reliability of a numerical method of assessing cavability. The review highlighted a number of issues, which at this stage, make numerical continuum methods problematic for predicting cavability. This is in particular reference to sensitivity to input parameters that are difficult to determine accurately and mesh dependency.An extended version of the Mathews method for open stope design was developed as an alternative method of predicting the onset of continuous caving. A number of caving case histories were collected and analyzed and a caving boundary delineated statistically on the Mathews stability graph. The definition of the caving boundary was aided by the existence of a large and wide-ranging stability database from non-caving mines. A caving rate model was extrapolated from the extended Mathews stability graph but could only be partially validated due to a lack of reliable data."

Jan 1, 2003

By Kazutoshi Haga, Ariunbolor Narankhuu, Ariuntuya Battsengel, Yasushi Watanabe, Altansukh Batnasan, Akita University

"Rare earth minerals are usually concentrated by flotation, magnetic or gravity separation methods to produce concentrates that are subsequently leached with hydrochloric (HCl), sulfuric acid (H2SO4) or nitric acid (HNO3). About 75 % REEs are lost in gypsum by-product when apatite is dissolved in H2SO4, whereas more than 80% of REE can be extracted from the apatite using HCl and HNO3 leaching processes, respectively. Therefore, the main aim of this study was to find an efficient process of dissolution of rare earth elements (REEs) from apatite ore by sulfuric acid solution due to its lower cost. In order to optimize the dissolution process, effects of different parameters, namely, concentration of H2SO4 (0.05 – 6 M), solid/liquid phase ratio (1:50 – 1:100), temperature (20 – 80 ºC), agitation speed (300 – 900 rpm), and leaching time (0.5 - 6 h) on the dissolution of REEs from apatite ore were examined in various intervals. The contents of main REEs in the apatite ore used in this study were (as % wt): 3 % La, 6 % Ce, 0.6 % Pr, 2.1 % Nd, 0.2 % Sm and 0.3 % Y. X-ray diffraction (XRD) analysis identified fluorapatite and phlogopite as main minerals in the ore. The results obtained from leaching experiments showed that more than 85% of REEs were dissolved from the apatite ore under the optimized conditions, which were: 1 M H2SO4, particle size of -150 + 100 µm, S:L phase ratio of 1:50, agitation speed of 500 rpm at 20 ºC for 1h. The XRD analysis revealed that main mineral compositions of the residues from 1M and 6 M H2SO4 leaching are gypsum (CaSO42H2O) and hemigypsum (CaSO40.5H2O), respectively.INTRODUCTIONThe term rare earth elements (REEs) denote the group of 17 chemically similar metallic elements consisting of the 15 lanthanides, plus yttrium (Y) and scandium (Sc) in the periodic table. These metallic elements are generally divided into two sub-groups; (1) the cerium sub-group, which is called “light rare earth elements” (LREEs), includes the elements from lanthanum (La) to europium (Eu), and (2) the yttrium (Y) sub-group elements, which are known as “heavy rare earth elements” (HREEs), are the remaining lanthanides from gadolinium (Gd) to lutetium (Lu) plus yttrium (Gupta and Krishnamurthy, 2005). The REEs occur together in the minerals due to their chemical and physical similarities, which cause problems of separating them from one another (Abreu and Morais, 2014). Although REEs are relatively abundant in the earth’s crust, they are typically dispersed and rarely occur in concentrated forms, making them economically challenging to obtain. There are a wide variety of rare earth minerals, however economic deposits of REEs in mining are bastnasite (La, Ce) FCO3, monazite (Ce, La, Y, Th) PO4, and xenotime YPO4 (Binnemans, 2013; Xie, et al, 2014). Due to the unique physical, chemical, catalytic, electrical, magnetic and optical properties of REEs, demand of these elements has increased dramatically with the advent of new technologies in electronics, communication, construction, energy and medicine (Jordens, et al, 2013). Since 1990, China has provided about 90 % of REEs worldwide. Japan and United States are the largest consumers of China’s REEs. In 2010, China announced to reduce REEs exports to Japan, as it tended to increase prices of REEs and to reduce a stable supply of REEs in the world market (Humphries, 2013). Therefore, there has been an increase in recent exploration activities intended to reveal new commercial sources of REEs and to bring them into production (Antico, et al, 1996). Apatite is an important host mineral for REEs in igneous and metamorphic rocks and can be used as an ore for those metals (Kanazawa and Kamitani, 2006). Apatite is also the main source of phosphate fertilizers and phosphoric acid (Habashi, 2013; Emsbo, 2015)."

Jan 1, 2016

"Eastern Canadian thermal coal mined at Minto, New Brunswick, and in western Cape Breton at St. Rose, Inverness County, Nova Scotia, contains 6-8 per cent sulphur. Both coals are high volatile bituminous. types. The Minto coal averages 18 per cent ash, 7 per cent sulphur and has a Btu rating of 11,900 per lb. Pyritic sulphur accounts for 75 per cent of the total sulphur and the remainder is largely organic; the amount of sulphate sulphur is negligible. This means that in a 7 per cent sulphur coal, 2 per cent is organic and 5 per cent pyritic sulphur. Pit-head St. Rose coal contains approximately 10 per cent ash, 7 per cent sulphur and 11 ,800 Btu/lb. The distribution of sulphur is different to that of Minto coal because about 12 per cent sulphate sulphur is present. Thus, a 7 per cent sulphur coal would contain 4 per cent pyritic, 2 per cent organic and 1 per cent sulphate sulphur.The iron sulphides, pyrite and, to a lesser extent, marcassite occur over a wide size range from large sulphur balls to crack fillings, lenses, and individual crystals and framboids. Coarse-grained pyrite and sulphur balls are easily separated during washing. It is the fine grain sizes, intimately mixed with the coal constituents, that are difficult to separate. Quantimet analyses of the fine grains in coal from both localities showed that about 50 per cent were smaller than 30 micron(1).No efforts have been made to wash the Inverness coal of Nova Scotia and in 1980 washing ceased in New Brunswick. Previously, the Minto coal was processed in an antiquated jig circuit which reduced ash from the strip operation run-of-mine value of more than 20 per cent to less than 18. More effective removal of ash and sulphur could clearly be obtained. Laboratory tests on both Minto and St. Rose coal have shown that ash rejection rates of 40 to 50 per cent at yields of 70-80 per cent were possible(2), Little information on sulphur removal was available."

Jan 1, 1981

By Graham A. Davis, Michael Samis

The dramatic fluctuation in metal and energy prices in the last few years is causing mining companies to consider alternative analytical methods for mine design and valuation. The goal is to improve insight into unforeseen changes in the economic and project environment and to design projects that take advantage of management's ability to respond to these changes. Such flexibly managed projects will contain value that cannot be measured using traditional engineering economic approaches, further motivating the used of alternative, modern valuation methods. This paper considers the valuation of an uneconomic low-grade resource at an open pit gold mine using two of the most popular modern valuation methods, Dynamic Discounted Cash Flow and Real Options. Our analysis demonstrates that the conventional valuation method may incorrectly represent the value and risk attached to mining this type of resource because it is unable to recognize management's ability to respond to future events in a manner that minimizes losses and exploits advantageous business conditions. The results of this paper highlight the importance of recognizing flexibility and business uncertainty in both mine design and valuation.

Jan 1, 2003

By A. E. M. Warner, A. Vahed, P. J. Mackey

In the decade 2002 to 2012 some 6.7 million tonnes of new copper concentrate production capacity was brought on line, corresponding to 2 million tonnes of contained copper. This increase in concentrate supply necessitated the commissioning of a number of new copper smelters as well as the modernization and/or expansion of existing plants to meet the demand. This paper gives an overview of the copper extractive industry, reviews recent copper production trends and changes in the copper industry, including an examination of pyrometallurgical and hydrometallurgical technology developments. WorleyParsons has supported a number of the projects involved in these developments and this role is briefly discussed. The paper introduces a number of ideas related to possible future directions of the copper industry.

Jan 1, 2014

By K. Hambrice, E. Fauveau

"When it comes to measuring the level of bulk solids, liquids, and everything in between, guided-wave radar technology now offers more level-detection capabilities than ever before. For an ever-widening range of previously hard-tomeasure products such as molten sulphur, liquid ammonia and petrochemicals, guided-wave radar transmitters provide accurate level measurements even under harsh chemical environments, wide variations in operating temperatures and pressures, and low dielectric constants.Great strides have been achieved in making these units easier to configure to a variety of process applications coupled with the simplicity of integrating these devices with most digital communication protocols. These improvements come as welcome relief to process engineers within an expanded range of level applications across several different industries that seek solutions to measuring the contents of tanks, silos, hoppers, bins, mixing basins, and vessels.Because radar transmitters have no moving parts, radar has already established a dominant niche in level measuring that quickly distances itself from mechanical means, which do not hold up as well in dirty service. Radar achieves its nonmechanical level detection capability by measuring the time of flight of the transmitted signal.Known more accurately as time domain reflectometry (TDR), the process involves sending microwave energy down into a vessel. When the pulse of radar energy reaches the product (indicated by a change in impedance), part of the pulse is reflected back toward the transmitter.A receiver measures the exact duration of time between the transmitted and reflected signal — the “time of flight.” The device analyzes this time and ultimately displays the level of the product as a distance in feet, metres, or other engineering units."

Jan 1, 2003

By S. Ng, Peter Stapleton, Paul Mankowski, J. Spence, R. Siy

"Syncrude has developed a low energy extraction process for the recovery of bitumen from oil sand. This new process operates at a temperature of 25 °C, resulting in substantially lower energy costs and lower capital costs, especially for the thermal energy generation equipment. The process will be used in Syncrude’s Aurora Mine, which is scheduled for startup in mid 2000. The flowsheet for Low Energy Extraction includes hydraulic transport of oil sand slurry, and bitumen separation using collector and frother chemicals and air as process aids. A number of flow sheet innovations and optimizations have been included, resulting in the next generation of extraction technology. Experimental pilot plant results, engineering progress to date and areas of ongoing work will be discussed. SUMMARYThe Low Energy Extraction Process has been successfully developed for commercial implementation at Aurora. The 1996 100 tonne hour Field Pilot demonstrated that the bitumen recovery target could be met with an 11.1% grade oil sand. However, pilot plant bitumen recoveries for a lower grade oil sand were not acceptable. The subsequent flowsheet optimization study led to a new flowsheet for Low Energy Extraction, which includes a primary separation vessel, a flotation circuit for PSV middlings, and the use of middlings displacement in the PSV cone bottom with flotation underflow. A test program conducted in 1997 showed that the new flowsheet could significantly improve the bitumen recoveries for lower grade oil sands. Engineering work on process scale-up led to selection of a 30 meter diameter PSV, with a tangential feedwell. The successful development and commercialization of Low Energy Extraction for the Aurora Mine Project is a major enabling step in the Syncrude 21 program. The low energy requirements of this process allow Syncrude to develop the Aurora leases more cost effectively. The use of this process results in major capital cost savings, predominantly in the thermal energy infrastructure and also provides long term operating cost advantages for Syncrude."

Jan 1, 1999

By A. H. Winckers

"CAMIRO, The Canadian Mining Industry Research Organization, formerly known as MITEC, is a collaborative research organization of Canadian Mining Companies. It is comprised of Exploration, Metallurgical Processing and Mining Divisions.The Metallurgical Processing Division (MPD) has the mandate to contribute to the profitability, competitiveness, safety and growth of the Canadian mining industry by improving the efficiency and effectiveness of mineral processing and extractive metallurgy in an environmentally conscious manner through the development of innovative technology by managing cooperative industry focused research programs.Current membership includes about ten Canadian mining companies. Past research has largely focused on base metal mineral processing. The Division wants to expand its research base to include all areas of mineral processing and extractive metallurgy.Past performance and plans for the future will be highlighted in the presentation."

Jan 1, 1998

By Pierre Gauthier

Is the hydrogen economy of the future just another fish story? Absolutely not! There have been many changes affecting the energy equation over the last 10 years and conditions have changed. In this presentation, we will examine the reasons why, in the very near future, hydrogen production and distribution will be increasingly visible on many industries? radar screens.

May 1, 2007

By William J. Davis, R. Blair Hrabi, Sally Pehrsson, Amelia V. Logan, Ross Sherlock

"Abstract - The Meadowbank gold deposits are hosted by a series of polydeformed and metamorphosed auriferous iron formations located in the Neoarchean Woodburn Lake group, western Churchill province, Nunavut. The supracrustal rocks in the Meadowbank area consist of a thick sequence of intermediate-composition volcanic rocks with intercalated iron formation, ultramafic volcanic rocks, and quartzite to quartz arenite. U-Pb geochronology gives an interpreted age of 2711 ± 3 Ma for the host strata at Meadowbank.The intermediate volcanic rocks are predominately volcaniclastic and have a geochemical composition that is consistent with an active continental margin setting. Iron formation deposition was coeval with the intermediate volcanism, as indicated by incorporation of volcanic detritus in the chemical precipitate. The geochemistry of the iron formation indicates that it precipitated from a fluid that at one time was at high temperature (>250°C), reducing, and likely acidic. Intercalated ultramafic rocks rarely show spinifex textures and have trace element ratios that are consistent with mantle plume-related undepleted mantle asthenosphere, likely recording episodic mantle upwelling associated with rifting in an active continental margin. The contact between the ultramafic volcanic rocks and the overlying quartz arenite is a disconformity marked by a quartz pebble conglomerate. However, similar geology on the structural hanging wall and footwall of the contact suggests that the conglomerate does not represent a significant hiatus in deposition, and is more likely a prograding terriginous siliciclastic unit.Three metamorphic events are recognized. The first, M1, is a cryptic greenschist facies event that is pre-D2. The second event, M2, is a mid-greenschist to amphibolite facies, syn-D2 event. M3 is the last event recognized, and is a post-tectonic greenschist facies event that is regional but inhomogeneous in extent, possibly reflecting thermal aureoles around post-tectonic 1.7 to 1.8 Ga Nueltin granites. The structural geology of the area is complex with four phases of deformation recognized, two of which had a significant effect on the geometry of the deposit. All of these regional events are interpreted as Paleoproterozoic in age. Relationships between deformation fabrics and mineralization, as well as the overall geometry of the mineralized envelopes, suggest that the deposit formed during syn- to late-D2. Superimposed on the mineralization are D4 structural elements that postdate gold mineralization.The main control on gold mineralization is replacement of magnetite by pyrrhotite and pyrite in high-strain corridors. The composition of amphiboles and chlorites associated with gold mineralization is remarkably consistent and shows no spatial or temporal variation, suggesting that it was buffered by the iron-rich nature of the host rocks. The bulk metasomatic effect on the intermediate volcanic rocks is characterized by the addition of K2O and the loss of CaO, Na2O, and MgO, with little variation in the total iron content. The elemental losses are likely the result of destruction of feldspars, stilpnomelane, and ferroactinolite, which are relatively common in the unmineralized rocks, and the formation of sericite, chlorite, and grunerite."

Jan 1, 2004

By Sub-Committee of the Committee on Research

"THE FOLLOWING REPORT was compiled by a sub-committee of The Metallurgical Society of CIM, Committee for Research, and represents a viewpoint of the steel industry in Canada. The objective was to define those areas in which the industry considers that external sources of Research and Development are a necessary function in supporting the in-house R & D conducted by the industry.On future occasions, the viewpoints of other metallurgical industries, such as those of nickel, copper and aluminum, will be presented. The report is divided into several sections: 1.-R & D Spending by the Steel Industry (a) Memberships in Recognized Steel Research Centres (b) Memberships in Recognized Industry Associations (c) Sponsored Research at Recognized Centres (d) Sponsored Research at Universities(e) Sporadic Research 2.-Areas for Research and Development(a) Instrumentation (b) Environment Control (c) Refractories (d) Sponsored Research at Universities(e) Electric Furnaces (f) Continuous Casting"

Jan 1, 1970