Search Documents

By F. L. Casey

"Part 1 – Published Papers Baria, G., and Boshkov, S., ""Insights into Undercuttingin Block Caving"", Proc. 5th Rock Mech. Symp.,Mines Br. - Information Canada, 41-58, 1970.Barron, K., Coates, D. F., and Gyenge, M., ""ArtificialSupport of Rock Slopes'', Mines Branch ResearchReport R228, July, 1970.Barron, K., ""Criteria for Brittle Fracture Initiation inand Ultimate Failure of Rocks and Their Applicationto Fracture Zone Prediction"", Proc. 2ndCongr. Int. Soc. Rock Mech., Belgrade, 1970, 3-37.Bauer, A., and Calder, P. N., ""Projectile Penetration inRock"", Proc. 5th Rocle Mech. Symp., Mines Br. -Information Canada, 157-170, 1970.Bauer, A. M., ""Site Development and Rehabilitation ofPits and Quarries"", Canadian Mining Journal,Vol. 91, No. 7, 77, July, 1970."

Jan 1, 1971

By R. J. Johnston

"INTRODUCTIONPoint Mines is located about 65 miles east of Hay River on the South Shore of the Great Slave Lake. It is connected to the Northern Alberta Railway System by the Great Slave Lake Division of CN Railways at Roma Junction, Alberta.The operation started in the fall of 1965 with a capacity of 5000 t.p.d. An addition was put into operation late in 1968 to bring the capacity up to 8000 t.p.d. The present milling rate is 11,000 t.p.d.The location of Pine Point Mines is such that long end cold winters are to be expected end temperatures of lower than -200F are encountered from late October to late March, with extended periods of -300F being common in January and February.It was recognized by Cominco engineers during the initial design period that since freezing would be encountered with open pit ore somewhere in the crushing circuit, the problem was to reduce it as much as possible. Other mines, working under similar conditions, found that the fine ore bins feeding the grinding circuit were the main problem area. The decision was reached, therefore, to have heated fine ore bins and to make sure thst the ore was sufficiently warm to prevent freezing.CRUSHING PLANT FLOWSHEETThe crushing plant has a standard open flow circuit (flowsheet). Ore from the stockpile is loaded into R-50 Euclid trucks by Caterpillar 992 Front End Loader with 11 cu. yd. bucket and dumped into a 42 x 65 C.A.C. Superior Crusher driven by a 300 HP motor. The crusher is set at a nominal 5 inches. The ore falls through into a 100-ton surge bin. There are high level and low level nuclear gauges to allow the primary operator to optimize for optimum orientation."

Jan 1, 1972

By D. J. Cheung, V. N. Kazakidis

ABSTRACT Seismicity and rockburst problems in hard-rock mines negatively impact safety and profitability. The authors propose a design risk methodology as a relative risk assessment for underground excavations vulnerable to rockburst damage. It considers rock mass conditions relating to mininginduced stress, geological structure, rock mass properties, and mining influence. Application of the methodology to rockburst cases involving seismically active fault zones at the Craig mine in Sudbury, Ontario, Canada, demonstrates that design changes can reduce exposure and economic risks. Mines with high geotechnical risk can use the design risk methodology to evaluate design alternatives as a risk management strategy.

Jan 1, 2014

"Yara Siilinjärvi in Finland is the Western Europe's only apatite mine. Annually it produces one million tons of apatite concentrate, which creates 10 million tons of tailings. At the beginning of 2017, Yara replaced their conventional TSF with a new tailings treatment plant, which increased the solids content of the slurry from 45–48% to 66–68%, making it possible to deposit as a paste. This extended the life-span of the current TSF from 2020 to 2035. This paper presents the storyline of the Yara paste plant project. The project began with laboratory testing and then progressed to pilot-scale thickening and beaching trials. After successful pilot trials, the final process design was implemented. Process automation played a key role in the project. An advanced control system is needed to maintain process stability and the desired operation point in various operational circumstances. Since commissioning the paste plant has been running consistently with an underflow solids content of 66-68%, with average beach slope angles of 3.5 degrees in the tailings disposal area. Robust thickener operation also leads to the trouble-free high-density pumping and high availability of the plan. During first year of operation the plant’s availability has been very good, over 97%, and currently, the plant is operated remotely from the main concentrator plant.INTRODUCTION The Yara Siilinjärvi Plant is owned by Yara International, a Norwegian fertiliser company. Yara Siilinjärvi is Western Europe's only apatite mine, and it primarily produces apatite concentrate for its Siilinjärvi phosphoric acid plant. A portion of the concentrate is also dried and shipped to other Yara fertiliser plants. The site annually produces one million tons of apatite concentrate, which creates approximately 10 million tons of tailings. Extending the lifespan of the 1150-hectare tailings storage facility has been studied in Siilinjärvi for a long time. The aim has been to use the same tailings area footprint, without any new land purchases or major dam increases. An important part of the process has been to study the possibilities for using new technologies, especially thickened tailings technology (Ruhanen, 2014)."

Jan 1, 2019

By A. P. Bois, K. Saleh, A. Ghorbal, V. Hajiabdolmajid, G. Ballivy

"The knowledge of the initial stress field is not always sufficient to ensure the stability of mining stopes due to the high-stress variations generated by mining. Monitoring of these openings is then necessary and can provide quantitative information (deformations and stress variations) as well as qualitative information (state of stability).An applied technique for following the variations of stress and deformation in static and dynamic conditions, in relation to the evaluation of the stability of underground openings known as “Cylindre Instrumenté de l’Université de Sherbrooke” (CIUS) is discussed in this paper. In addition, a data acquisition system combined with a rock failure warning system has been developed to be connected to the CIUS for detecting the instabilities, which can endanger the stability of underground openings. Also, the installation of six CIUS and a data acquisition system as well as the selected procedure of programming in a warning system are briefly described."

Jan 1, 2003

By S. D. Botts, F. Cantuarias

"The Antamina project, owned by BHP Billiton Plc, Mitsubishi Corporation, Noranda Inc., and Teck Cominco Ltd., is a $2.3 billion copper/ zinc project, located in the Ancash Department of Peru. The project consists of an open pit mine, a 70 000 ton per day concentrator, a 302 km long concentrate pipeline, port facilities, a new access road, power line, and town site. The project is designed to produce up to 1.5 Mtpy of copper and zinc concentrates over a 23 year project life, and will be the third largest producer of zinc and the seventh largest producer of copper in the world.This mega project is the largest mining investment in the country and, during its construction stage, was the most important construction project worldwide. On May 28, 2001, Antamina commenced testing operations and four months later, it reached commercial production. Antamina was officially inaugurated on November 14, 2001 by Peruvian president Alejandro Toledo.The construction stage of the project generated 8000 direct jobs, with a peak of 10 000 employees, and 30 000 indirect jobs. The permanent workforce consists of approximately 1650 employees, the vast majority of which are Peruvian Nationals, around 30% of whom came from the region where the deposit is located. Approximately 5600 indirect jobs were generated from the project. Independent sources state that Antamina increased the Peruvian mining exports by 30% (mining exports constitute 50% of Peru’s total exports) and Peruvian GDP by 1% in its first year of full operation in 2002.Since winning the privatization bid for the project in 1996, the company has implemented an approach to community development and environmental protection based on sustainable development principals. Throughout the development of the project, a number of initiatives have been undertaken to ensure full involvement of the local populations in community development activities and the company’s environmental program.Due to its size, difficult logistics, cultural considerations and financial aspects, the project has faced a number of unique challenges in the area of environmental protection and management of community interaction. Antamina has been innovative in its approach to these issues and, as a result, has set new standards in Peru for environmental and community management and sustainable development."

Jan 1, 2003

By Jozef S. Stachula

"INCO Limited operates eleven under-ground mines in the Sudbury area. The mines are located on the rim of the Sudbury Basin, an oval with the axis in the range of 27 km and 60 km. The ore dips to at least 3000 m below surface. The ores are mined primarily for nickel and copper. Total ore production from underground is in excess of 55 000tonnes per day.Over 40 surface fans have been installed since the late 1960s. All of the fans are adjustable pitch, axial flow units. A major factor influencing ventilation design in the last 30years has been the introduction of diesel equipment underground. Volumes per fan have ranged from 60 m3/sec. to 330 m3/sec., with motors from 100 hp to 2500 hp.Fans of the axial flow type have been commonly used for main fan installations at Canadian mines for many years. The standard arrangement has been to mount these fans horizontally, i.e. with the fan shaft and the long axis of the housing horizontal. This is a natural arrangement for an underground fan, but for a surface installation, a vertically mounted fan has definite advantages.The surface area taken up by a typical vertical fan installation is generally about one quarter that of a horizontal fan of the same capacity (Rutherford, 1957). This is not a problem with isolated fans and fat surface out crop sites, but where the installation is to be near existing buildings, or where there are poor surface soil conditions, space and cost considerations greatly flavour vertical fans."

Jan 1, 1996

By P. Desclaux, A. Gosselin

"In 1999, PFC measurements were carried out at Alcan smelters as part of a large measurement campaign led by the Canadian Aluminium Association. Side worked prebake (SWPB) and horizontal stud Söderberg (HSS) plants in Arvida were the selected sites. CF4 and C2F6 emissions were measured continuously in the exhaust duct and at the roof vents for a week. In parallel, voltages from four designated cells were recorded at a high scan rate. Results were analyzed and correlations between voltage, anode effect duration and PFC emissions were tested. Some fundamental anode effect mechanisms were proposed and validated with the observations. IntroductionFollowing the international agreement reached within the scope of the Kyoto protocol, voluntary partnerships have been established in many countries especially for the aluminum industry. It is well known that the PFCs that are periodically emitted during aluminum production are the major source of fluorocarbon emissions. The latter are part of the greenhouse gases. In the fall of 1999, Alcan announced that it will adopt, promote and regularly renew a long-term greenhouse gas management commitment at all of its facilities within the framework of the so-called TARGET program that was implemented during 2001. The program is intended to produce on-going reductions, which will be reported publicly on an annual basis.Improvements in the understanding of the mechanisms leading to PFC emissions will contribute to targeting the most appropriate reduction actions. PFC measurement campaigns have been driven toward this end. The first measurement campaign was conducted in 1993 in order to get a picture of the emissions and a base line. The last measurement campaign was conducted in 1999 and its main objective was to compare current emissions with those measured in 1993 and to confirm the accuracy of the predictive equations for the calculation of PFC emissions. This campaign has been conducted by the Canadian Aluminium Association and measurements were made in plants using different technologies. Results of this campaign have already been reported by Bouchard et al. (2001)."

Jan 1, 2002

By C. S. Parsons

Ore-Testing laboratories are maintained by the Mines Branch, Department of Mines, at Ottawa for the purpose of conducting experimental test and research on ore treatment. Sample shipments of a few hundred pounds to car-load lots of Canadian ores are received on application for experimental tests, and all possible methods of treatment are investigated. Reports are issued to the shipper, containing the results, with recommendations as to the most economical method of treatment. These reports have been of valuable assistance to mining companies in the preparation of plans for the design and equipment of their treatment plants. Investigations have been conducted on ores and metallurgical products from all parts of the Dominion. The ores from practically every producing mine and important mineral occurrence have been investigated in these laboratories.

Jan 1, 1931

By M. Xian, M. Jahazi, Y. L. Lin

The 2-mm butt joints of ZE41A-T5 sand castings were laser welded at different defocusing distances on two surface conditions (as-cast or machined) using a continuous wave 4 kW Nd:YAG laser system at a power of 2.5 kW and a welding speed of 6.0 m/min. Two welding modes (conduction or keyhole) have been observed. The adjustment of defocusing distance can greatly influence the establishment of conduction or keyhole modes. On the machined surface conditions conduction welding is obtained at a power density of 4.0 x 105 W/cm2. In contrast, keyhole welding is reached at a threshold irradiance of 1.5 x 106 W/cm2. Neither conduction nor stable keyhole modes have been established at a range of power density from 7.7 x 105 to 1.2 x 106 W/cm2 on the machined surface conditions. On the as-cast surface conditions keyhole is obtained at a power density as low as 4.0 x 105 W/cm2 but good surface quality is obtained at a defocusing of +2 mm. The as-cast surfaces require lower power irradiance for the formation of keyholes indicating that they have higher energy absorptivity for Nd:YAG laser beams probably due to coarse surface morphology.

Jan 1, 2004

By C. R. Hocott

"IntroductionRESEARCH in petroleum production consists primarily in investigations related to the drilling for and recovery of oil. As an organized activity of individual oil companies, production research is now 30 to 35 years old, and the petroleum industry may point with justifiable pride to the achievements of this third of a •century. Emphasis on research has grown through the years until at the present time many of the larger companies operating in the United States •have well-organized production research staffs.In addition to the efforts of the oil companies, significant research and development in petroleum production technology have been performed by oilfield service companies and others. Valuable contributions have been made through fundamental research carried on by the U. S. Bureau of Mines and by various colleges and universities, both in their own programmes and in programmes sponsored by industry, such as those of the American Petroleum Institute. However, the total effort of these groups is small when compared to the sum of the effort devoted to research by the individual .oil companies. In contrast to some industries which conduct the major portion of their research through co-operative, sponsored research at universities or research institutions, research by the petroleum industry is done predominantly by individual company research staffs. These industrial research groups have usually been organized in such a way as to provide liaison and co-ordination with operating technical staffs. In this way, the research groups are kept aware of the major problems confronting the operating departments and, correspondingly, the operating technical people •are able to keep informed on research activity and progress. This type of close contact generally results in prompt testing of research developments in actual operations."

Jan 1, 1953

By J. D. Wilkins

"Ore outcrops were first discovered in the area in 1911. Following various periods of exploration by private interests and Cominco Limited, the Coast Copper Company, Limited property was brought into production in August 1962. Subsequently, Cominco explored the adjacent Quatsino Gold Mines property and is currently developing, and producing from, what is now known as the Benson Lake Mine.The Benson Lake Mine was developed using a conveyor-equipped decline and trackless LHD equipment. The operation produces 800 tons per day of copper-iron ore, copper being the main product. Copper and iron concentrates are trucked 25 miles to storage and shiploading facilities near Port McNeill to await shipment to Japan."

Jan 1, 1971

Real Time Monitoring of Cemented Paste Backfill Introduction Methods ?how to instrument a Long Hole stope Key Results from 2 case studies: barricade pressures and displacement, in-stope pressures Importance of Real Time Monitoring How binder, rise rate, cement content affect fence pressures

May 1, 2010

By Da-Qiang Cang, Qingde Wang, Wei Wang, Wen-Bin Dai, Min Guo, Yu Li

Utilization of both slag and its heat for hot slag is a great challenge for iron and steel industry. Many methods of hot slag modification for directly converting hot slag into value-added materials were researched in recent years, and waste heat of hot slag could thereby be transformed into inner energy or chemical energy of the materials. In this paper, an experiment of converting hot slag directly into glass ceramics by hot slag modification method was conducted. A cooled modifiers mainly composed of fly ash were firstly heated though a cyclone furnace and then fell into a molten bath to mix with hot steel slag. Half of hot slag was used as raw materials and accordingly about half energy consumption, about 5MJ/kg for melting raw materials was saved in the process compared with that of traditional producing method. Frit quenched from the modified hot slag had a higher basicity of 0.6-0.7 than traditional frits in order to reduce the needed amount of cold modifiers and accordingly utilize more hot slag and its waste heat. Glass ceramics were further prepared from the frit and a heat treatment of one-stage method is more suiter to such frit than that of two-stage method. The glass-ceramics with basicity of 0.6 and heat-treated by one stage method had the best performance with bending strength of 146.46 MPa, Vickers hardness of 6.79 GPa, water absorption rate of below 2% and shrinkage rate of around 10%.

Jan 1, 2015

By Christopher Boys

"Abstract -Many water inflows in Saskatchewan potash mines are linked to salt anomalies. Potash ore and three anomalies in the PCS Cory potash mine in the Patience Lake Member of the Prairie Evaporite Formation were studied to understand the processes involved in their formation. Another goal was to find geological indicators of the proximity of anomalies. A geological model that relates the potash to the salt anomalies has been developed.Up to five post-burial facies may be recognized . These range from carbonate-mud collapse breccias to bedded sylvinite, and probably result from post-burial leaching. ln this model, the same fluids that caused widespread recrystallization and possibly enrichment of the potash salts, started by dis­ solving huge cavities in the evaporites . The effects of the leaching were highly variable, indicated by selectively preserved delicate laminae and chevron textures, to deformed and totally dissolved salt beds . ln at least two major events, Late Devonian and Cretaceous, collapse structures may have acted as conduits for overlying formation waters to cause pervasive leaching and recrystallization of the Prairie Evaporite Formation .Geological indicators of the proximity of an anomaly may include: a change in Insoluble seam color from greenish-gray to mottled brown and greenish-gray, unusual local increases in ore grade, large patches (e.g., >200 cm2) of sylvite-poor potash crosscutting units near the top of the ore zone, and drops in topography >10 m of the marker seams. Anhydrite was more common in an anomaly than in ore. The local abundance of anhydrite in ore may indicate the proximity of some salt anomalies.Once an anomaly has been encountered, indicators of a major collapse feature may include: stretched clay seams, folded beds, small collapse features (1 m to 20 m), numerous washouts, or split clay seams with injected salt. Any number, or none, of these indicators may be found close to a major collapse feature."

Jan 1, 1993

By M. J. Nicol, C. van Wensveen

The kinetics of the oxidation of thiosulfate by copper(I I) in ammoniacal solutions have been studied in the presence and absence of dissolved oxygen. The formation of an intermediate mixed ammine/thiosulfate copper(II) complex ion has been confirmed and the rate of the reaction monitored by simultaneous on-line spectrophotometric, dissolved oxygen and potentiometric measurements. The rate of the anaerobic oxidation of thiosulfate by copper(II) was found to be orders of magnitude slower than that in the presence of dissolved oxygen and is inhibited in the presence of ammonia and anions such as sulfate and chloride as a result of competition with thiosulfate for the axial coordination sites on the copper(II) tetrammine complex. In the presence of dissolved oxygen, it was found that the copper(I) thiosulfate complexes are only very slowly oxidized while the copper(I) diammine complex is rapidly reoxidised to the copper(II) state. Thus, the initial rapid reaction with copper(II) leads to a pseudo steady-state condition in which the concentration of copper(I) is relatively constant and the rate of oxidation of thiosulfate can be predicted from the measured rate of oxidation of copper(I) by oxygen in ammoniacal solutions. The effects of the concentrations of ammonia and thiosulfate on the oxidation rate can be rationalized on the basis of the above coupled to the species distribution of copper(I) in the ammonia/thiosulfate system. It is shown that, with relatively simple measurements of dissolved oxygen and copper concentrations, the rate of oxidation of thiosulfate can be predicted under typical leaching conditions.

Jan 1, 2005

By Vic Briccardi

Energy Management Challenges The Holistic Standard to Energy Management Energy Management Information System (EMIS) "Best Practices?: Energy Management Maturity Curve De Beers Canada Profile & Mine Locations Significant ROI Driven by Real-Time Energy Visibility Mining Energy KPI?s Summary: What Does EMIS Deliver? Q&A Session

May 1, 2013

By D. W. Ginsberg, D. Cieplinski

"The lifetime cost of a material handling system, or any mine system, can be reduced through the application of quality engineering. Dynamic simulation is a powerful tool that can be used to enhance the experience and ingenuity of the design team. It cannot only de-bottleneck the system to improve system productivity, but also define critical design criteria to eliminate over-design and reduce capital cost. Eliminating over-design also reduces operating costs by lowering component replacement costs and by ensuring all parts of the system operate at a higher utilization and efficiency. IntroductionA mine owner’s profitability is improved when a mine is developed at the lowest lifetime cost. This cost relates not only to capital and operating costs, but also, to a great extent, on the efficiency and reliability of the operation. These factors are tied directly to the quality of the engineering which depends on the experience of the engineers involved, and their ability to apply known system information in a rational and constructive manner.It is becoming apparent that it is increasingly more difficult to deliver the quality of engineering expected and needed to provide attractive lifetime costs using traditional design methods. Historically, system information has been evaluated based on a limited amount of information to which global rules-of-thumb and the engineer’s personal experience were applied to develop design criteria. However, market forces are dictating that more system parameters be defined and that they be defined more accurately so that the most economical system can be developed. This increase in the volume of information and the need for more accurate predictions is straining, if not already exceeding, the ability of engineers to apply simple global rules of- thumb and to combine all the information in a rational, comprehensive and representative set of design criteria. Furthermore, as proposed system production rates increase beyond established industry practice, the extrapolation of the engineer’s experience becomes more difficult and increases the risk in the proposed design."

Jan 1, 1998

By A. P. Schissler

Mining has several characteristics, uncommon in other business sectors, which pose additional challenges to the implementation or design of IT and management systems that use the information. Understanding these characteristics would improve the chances of successfully importing new information technology and management techniques to mineral producers. The most important characteristics that should be understood are workplace issues, the industry’s dual nature of being a continuous construction project using cyclical factory processes, labour challenges, workplace culture, information availability, integrative data elements, and the current technical education of mining engineers. These characteristics were taken into account in two applications of information technology and systems design at operating companies. The research and consulting projects focused on the development of an IT-enabled performance management system at several underground metal mines in Canada and an integrated data warehouse for surface mines spread throughout the United States and Latin America.

Jan 1, 2006

By J. K. Atherton

If the metals sector is to contribute successfully to sustainable consumption we must adopt principles and practices which address the entire life cycle of the materials we produce. Progress must be founded on a sense of shared responsibility for the resources we utilize and the materials we create - it is this integrated approach which lies at the heart of materials stewardship. Materials stewardship means mining and metals companies producing materials in a responsible manner and then working with others, beyond their site, to ensure that the downstream material flows and applications are managed properly to create maximum societal value. In September 2006 ICMM published 'Maximizing Value: Guidance on implementing materials stewardship in the minerals and metals value chain'. This document takes a practical view presenting structured guidance as well as good practice case studies. In the publication, materials stewardship is described in terms of the range of activities that can be undertaken to ensure that all parties work collectively toward the responsible use of metal and mineral resources. This paper introduces the materials stewardship concept as set out in `Maximizing Value' and describes the business case for implementation as well as the ICMM framework for promoting materials stewardship.

Jan 1, 2007