Search Documents

By Hämäläinen M., O. Hyvärinen, E. Jääskeläinen

HydroCopperTM is a new hydrometallurgical process for the treatment of copper sulphide concentrates, which has been developed by Outokumpu. The process includes chloride leaching of copper concentrate, solution purification and precipitation of copper(I) oxide, an intermediate product, which is reduced and cast into copper products. The reduction can be carried out by pyrometallurgical methods or hydrometallurgically in an autoclave. This paper discusses the thermodynamic and kinetic aspects of the hydrogen reduction of copper(I) oxide in an autoclave. The results of the laboratory tests are presented and discussed. Finally, the autoclave method is compared with other options.

Jan 1, 2004

By Donald L. Mordell

Introduction A very large part of the world's fuel resources are in solid form, as various grades of ?coal, but an increasing proportion of fuel demands on this Continent and else-where are having to be met by liquid fuels. Convenience and, in many cases, cost weigh heavily in favour of the liquid: fuels, and there are many fuel burning applications where the use of coal would be impractical, such as for automotive or air transport. By extrapolating the present trends one might conclude that, in future years in Canada and the United States, coal will be used only in a few power stations close to coal fields. If such a state of affairs should arise, it will obviously prove embarrassing to those accustomed to make their livelihood from the winning and marketing of coal, but it is perhaps not so obvious that it must also prove an embarrassment to the nation. The major reasons for this are two in number. Firstly, if present coal production is to be replaced by oil production, a large capital expenditure is necessary, which must inevitably be paid by the consumer; and secondly, in times of emergency, large amounts of oil fuels are required for military purposes which cannot be achieved with solid fuels. It is obviously unwise, therefore, to discontinue the use of coal for those non-military jobs that it can do. If we examine the major fuel markets we find that there are three: Domestic heating Steam generation Transport by air, sea, and land For domestic heating, the extreme convenience of oil, in spite of its greater cost, has captured much of the coal market.

Jan 1, 1952

By Z. Xiao, A. R. Laplante

"The recovery of gold by gravity from grinding circuits differs from virtually all other gravity recovery approaches in that stage (or unit) recoveries are low, typically 1 to 5%, but overall recoveries are generally in the 25 to 60% range, because individual gold particles are presented many times to the primary recovery unit. Full-scale recovery is difficult to predict from benchscale tests. Further, maximizing metallurgical recovery is generally not the primary objective, because of the more efficient downstream recovery circuit (flotation or cyanidation). In this paper, a new concept, the gravity recovery effort, is presented to assist in the design and optimization of gold gravity circuits. It is defined as the product of the circulating load treated by the primary gravity unit, the recovery of this unit, and the gold room recovery. Predicted gold recovery is linked to the recovery effort, the size distribution of gravity recoverable gold (GRG), the dimensionless retention time in the mill and the partition curve of GRG. A case study of economic optimization of the gravity recovery effort is presented. INTRODUCTIONPredicting gold gravity recovery from grinding circuits has always been a hit-and-miss exercise. The problem can be traced to the highly variable gravity recoverable gold (GRG) content of ores, high GRG circulating load, fraction of the circulating load treated, and performance of primary gravity recovery and gold room. Typical values, highs and lows are shown in Table 1."

Jan 1, 2001

By R. Stratton-Crawley, S. W. Wilson

"Inco's Matte Separation Plant is a unique mineral processing facility having no process tailings stream. Each product is a high-grade concentrate with strict assay specifications which are defined by the downstream refining route. The most recent column application in the flowsheet, copper scavenging in the production of a high quality nickel concentrate, is described in detail. Testwork in pilot-scale columns (0.038 m, 0.051 m and 0.10 m in diameter) was used to develop a model of the copper scavenging system. This data was then used to simulate the performance of plant-scale equipment. The relationships thus established were confirmed by a series of plant tests in a 1.8 m diameter column. Column results consistently exceeded conventional cell performance. The modelling was extended to assess full plant production requirements and, as a result, a 2.1 m diameter column was specified for this application. Engineering design for this column is currently underway and the column is scheduled to be commissioned later in 1991.INTRODUCTIONMatte SeparationINCO's Matte Separation Plant is a part of the Copper Cliff Smelter complex near Sudbury Ontario. The flowsheet and the development of column flotation within it have been described previously (Feeley et al., 1987, Wilson et al., 1989). The plant feed is a synthetic Bessemer Matte from the Nickel smelter. This matte is slow cooled to promote grain growth and typically assays 46-52% Ni, 23-27% Cu. These elements are present primarily in sulphide form (Ni3S2 and Cu2S respectively) with some metallic alloy also precipitating from the sulphur deficient matte. Minor amounts of iron, precious metals, and nuisance elements are also present.The matte separation process is, in concept, relatively simple. Following magnetic removal of the metallic alloy from the feed, the flowsheet is designed to float a high grade copper concentrate from the nickel sulphide matrix. A simplified flowsheet of the process is shown in figure 1."

Jan 1, 1991

By B. R. Conard

Copper refining at Vale Canada (previously known as Inco) has been associated with Ni production. Because Cu and Ni carry risks for adverse health endpoints through inhalation exposure, it is critical that their aerosol levels, and the metallurgical processes through which they enter the air, are understood. Because certain Ni substances have been linked to respiratory cancers, it is also important to characterize the amounts and types of Ni compounds in occupational settings. This paper describes electrorefining and electrowinning operations near Sudbury, Ontario (1930–present), and gives aerosol measurements (1978–present).

Jan 1, 2014

By Jean Dugas, Roger Sirois

The Mineral Deposits Service of the Quebec Department of Natural Resources is engaged in the preparation of metallogenic maps as a contribution to the Canadian Sub-Committee of the Metallogenic Map of North America. The preliminary work is being done on large-scale maps. The main objective is to clearly represent information on ore deposits in a suggestive way. The design of the legend to meet these requirements is discussed. As these maps are still only descriptive, a further step will be the interpretation of data into metallogenic maps with Jess emphasis on the individual deposits and more on the metallogenic factors. Both types of map should prove useful in the search for ore deposits; the first by providing at once a large amount of information, the second by suggesting the ore controls.

Jan 1, 1967

By R. Tyreman, G. Ritson

"The Red Lake Mine is situated in Balmer Township, Red Lake area in northwestern Ontario. It is an underground mine that has been in production since 1948. The property was originally known as the Dickensen Mine and was shut down in 1996.A feasibility study was carried out in 1998 and it was determined that a new mill should be constructed with a throughput rate of 600 stpd. The life-of-mine average gold grade was projected to be 1.35 oz/t with gold predominantly associated with arsenopyrite and pyrite. Metallurgical testwork indicated that the optimal flowsheet for gold recovery would include an autoclave for oxidation with a carbon circuit for adsorption. To limit capital cost and establish cashflow, the mill was constructed without an autoclave. The recovery by gravity and cyanidation was projected to be 83%. A flotation plant was constructed at the tail end of the circuit to recover the additional gold associated with sulphides from the leach circuit tailings. This material is being stockpiled onsite for future oxidation treatment.Detailed engineering was started in early 1999 and the first gold was poured in August 2000. One feature of the project was the use of Contact Lake equipment from Cameco’s Contact Lake project. The entire mill was purchased and equipment re-used where possible. The capital cost for the process facilities was C$3 1.5 million."

Jan 1, 2001

By D. H. Flather, J. W. Hendry, K. Drover

Black Hawk Mining Inc. has completed a comprehensive program on the prediction and management of acid rock drainage (ARD) at their Keystone Gold Mine (Keystone) near Lynn Lake, Manitoba. The program, initiated in 1994, followed a phased approach utilizing initial acid-base accounting (ABA) results and subsequent laboratory kinetic testwork to define site-specific sulphide oxidation and neutralization consumption rates in waste rock. Net acid generating waste rock at Keystone was defined through the kinetic testwork as waste rock yielding a net potential ratio (NPR) of less than two. A preliminary waste rock management program based on blending of potentially acid generating and acid neutralizing waste rock was advanced. Subsequent refinement of the management program followed the analysis of over 1580 ABA samples collected from individual blast holes during the initial bench development phase of the Keystone pit. Uncertainties in actually achieving adequate blending within the dumps at a mining- scale resulted in the development of a revised waste rock management program based on segregation. Recognizing that any successful management plan requires that the ARD characteristics of the waste rock be identified prior to in-pit blasting, the extensive ABA database was utilized to develop a rapid characterization scheme. By implementing a characterization scheme based on total sulphur concentrations and fizz rating, waste rock could be quickly segregated without delaying the natural flow of ore from the pit. Interestingly, it also became apparent that gold values were strongly correlated with total sulphur, such that traditional fire assays were supplanted with a simple and more cost-effective total sulphur determination. The program highlights the importance and benefits of collecting and exploiting data beyond that necessary to acquire appropriate development permits.

Jan 1, 2000

By Dave Price

"Canada is scheduled to become the 4th highest diamond revenue producing country in the world by year 2004 with the already operating Ekati Mine and the anticipated operation of the Jericho Mine in 2002 and the Diavik Mine in 2003.This paper provides an overview of worldwide diamond production statistics and a brief introduction to a diamond processing plant. The dense medium separation (DMS) extraction process is presented and this process is discussed in more detail with respect to the extraction of diamonds in terms of feed preparation, dense medium, dense medium cyclones, ferrosilicon recovery and dense medium cyclone operating efficiencies.INTRODUCTIONThe Ekati Diamond Mine in the Northwest Territories started commercial production of diamonds in the 4* quarter of 1998. At full production, the mine is anticipated to produce annually some 3 million carats of diamonds. The Jericho Mine in Nunavut Territory and the Diavik Mine in the Northwest Territories are anticipated to come into production in the 1'' quarter of 2002 and 1st half of 2003 respectively. The combined annual diamond production of these three mines will total approximately 10.34 million carats by 2004, making Canada the 4~ highest diamond revenue producing country in the world.A diamond processing plant initially utilizes crushing, scrubbing and screening in the beneficiation process to liberate diamonds from kimberlite ore and size the product for further treatment through DMS. Alluvial diamond operations do not require initial crushing and scrubbing but incorporate a feed preparation and sometimes a recrush facility with the DMS plant. The heavy sink product from the DMS, which contains diamonds, is further upgraded through x-ray separation and high intensity magnetic separation prior to producing the final diamond product.DMS is a relatively simple separating principle. A mixture of particles of different density is immersed in a dense fluid, so that particles having a density lower than that of the fluid will float while those of heavier density will sink. The translation of the float-sink principle from a laboratory method to continuous industrial practice offers the prospect of very precise mineral separations based on density differences alone."

Jan 1, 2000

By K. V. Konigsmann

"The mill at Mattagami Lake Mines treats 3,850 tons per day. The mill feed is a heavy sulphide ore. It is composed ofPyrite & Pyrrhotite - 40%Marmatite - 17%Chalcopyrite - 2%Magnetite - 10%Talc and other Silicates - 31%The sulphides are intimately associated with each other and often finely disseminated throughout the siliceous gangue. An abundance of middling particles exist in the circuit and a delicate balance has to be maintained between concentrate grades and metal recoveries.The metal content of the mill feed fluctuates between 0.4 to 0.7% for copper and 6 to 13% for zinc.The flow sheet of the concentrator is shown in Figure 1.Eight sample streams have been selected for on-stream analysis, namely1. Copper Concentrate 2. Copper Cln Tailings 3. Copper Tailings 4. Zinc Concentrate5. Zinc Rgh Concentrate6. Zinc Cln Tailings7. Zinc Rgh Tailings8. Flotation TailingsThe mill feed is not being analysed. Only a very coarse sample could be obtained which would be difficult to pump, and the fluctuations in the copper content are too small in absolute terms to have much of a bearing on circuit operations."

Jan 1, 1969

By X. -G. Chen, J. Qin, K. Liu, D. Racine

"Understanding the thermo-mechanical fatigue (TMF) behavior of materials plays a significant role in the safety design of critical components used in aerospace and automotive industries, such as engine blocks and cylinder heads, which undergo the cyclic change of temperature and stress. However, the cyclic changes of temperature, stress and strain make it difficult using the traditional testing methods to accurately simulate the TMF process. In the present work, the Gleeble® 3800 system was successfully applied to develop a reliable procedure to measure the TMF behavior of aluminum alloys. The modified setup together with the new designed program allows the Gleeble system to precisely simulate the cyclic profiles of temperature and mechanical strain. The novel procedure includes the calibration and verification of the TMF setup to ensure the test validity with Young’s modulus measurement, multi-cycle measurement of the thermal strain and zero stress adjustment followed by online monitoring the TMF cycles. The results of the TMF testing of an AA6061 alloy under cyclic temperatures (60–300°C) and various strain amplitudes (0.2–0.6%) were demonstrated. Its TMF behavior was characterized by the typical hysteresis loops and cyclic stress-strain response.INTRODUCTION The thermo-mechanical fatigue (TMF) behaviour becomes increasing important to evaluate the elevated-temperature properties of materials used as the critical components in automotive and aerospace industries, such as the gas turbines (Hu, Shi & Yang, 2016; Moverare, 2007; Segersäll et al., 2015) and engine blocks (Grieb, Christ & Plege, 2010; Javidani & Larouche, 2014). During the cycles of start-up and shutdown of the engines, these components undergo a complex change of loading. Meanwhile, a dramatic temperature gradient exists on the components due to the cooling system. Therefore, the cyclic changes of load and temperature can give rise to the TMF and may limit the use life of such components (Hu, Shi & Yang, 2016; Javidani & Larouche, 2014; Moverare, 2007). Hence, performing the TMF tests to precisely simulate the cyclic changes of load and temperature to understand the TMF behaviours of materials is playing a significant role in the safety design of these components. For TMF tests, two principal types of cycles are generally employed, including the in-phase (IP) cycle where the load and temperature are at the same phase (i.e. maximum load at highest temperature) and out-of-phase (OP) cycle where the maximum load is applied at minimum temperature (Kliemt, 2012; Miller, 2014). The most significant damage mechanisms in engine components are reported to be OP TMF cycles (Javidani & Larouche, 2014; Kliemt, 2012)."

Jan 1, 2018

By Michael Cullen

The Quinsam Coal Mine is in the process of extracting a panel beneath the mine access road. To prevent damage to the road, and adjacent powerline, it was necessary to establish a ?protection zone? within which the extent of mining would be limited. The protection zone is analogous to the setback limit. For economic reasons it was desirable to make the protective zone as small as possible, and with the greatest extraction ratio possible. The size of the protective zone was established by determining the angle of critical deformation using the numerical model FLAC, coupled with field data on subsidence from the Mine. The angle of critical deformation (defined as the angle, measured from the vertical, at which intolerable damage is sustained by a structure) was determined to be between 0 and 5 degrees. The allowable extraction ratio in the protection zone was established using the ARMPS method of pillar design coupled with field data on pillar stability from the Mine. Excavations spans to prevent caving were determined by historical experience and field data on span stability from the Mine, coupled with numerical modeling. The minimum pillar size was determined to be 7.5m. The maximum pillar height was established at 2.5m. The maximum allowable excavation span was determined to be 8.5m. With these criteria, extraction ratios between 54 and 73% (measured in plan view) were determined to be appropriate for the protection zone.

May 1, 2001

By G. A. McGuffin

"IntroductionWITH the increase in quantity of sour gas reserves in the Province of Alberta, and the wider market for sulphur brought about by mounting world demand and restrictions placed on the principal supply, it was inevitable that this important source of sulphur would be .developed. In the light of these facts, it seems timely that a general paper on sulphur recovery from petroleum gases be presented. This, then, is the purpose of the following text. A short discussion of each of the following subjects is presented:(1) Properties and uses of sulphur(2) Existing sources(3) Market research(4) The recovery process in Turner Valley(5) Hazards of sulphur productionNo pretext of originality of material is made since innumerable reports have been prepared on this and related topics and information contained in these has been used quite liberally.Properties and uses of SulphurSulphur is a non-metallic element having an atomic weight of 32.06. The stable crystalline form at atmospheric temperature is referred to as 'rhombic' sulphur. It is bright yellow and has a specific gravity of 2.05, equivalent to 129.2 lb./cu. Ft. Above 204°F. sulphur has another stable crystalline form, referred to as 'monoclinic'. This is reddish-brown and is slightly less dense than the rhombic variety (122.4 lb./cu. Ft.). Sulphur in bulk form weighs 84 to 90 lb. per cu. Ft. Sulphur melts at approximately 240°F. to a straw coloured liquid which is quite viscous."

Jan 1, 1952

By A. LA. Salama, D. B. Hyma

"The Western Research Centre (WRC) of CANMET located in Devon, Alberta, is a modern research facility offering services ranging from fundamental research to pilot plant investigations. Recently, a 0. 76 metre diameter by 7.9 metre high Flotaire column flotation cell was installed as a demonstration unit for Canadian coal producers. Because the column cell is intended to be used for research, development and demonstration, WRC recognized that additional sensing equipment and improved process control would be required to generate good data for subsequent column scale-up and engineering design.A low cost, personal computer based control system was, therefore, designed and installed. This paper describes the stepwise procedure in developing the control strategies, selection of system software and hardware, and installation and configuration of the system.Preliminary performance data on a western Canadian coal sample are also presented. Future testwork is planned on additional coal samples to expand upon existing database."

Jan 1, 1993

By R. Hammen, J. Lifton

"The purification of rare earth elements (REE) at mining operations is traditionally accomplished by multiple chemical phase-transfer processes including precipitation, solvent extraction, and ion exchange. We describe REE purification results with Solid Phase Extraction (SPE) columns that were developed to improve the speed and economy of REE purification. The SPE columns have the properties of enhanced equilibration kinetics, so that residence time of a few seconds will accomplish selective chemical transfers from solution phase to solid phase. We describe the separation of REE’s as a class from leach solutions and the further purification of REE salts. INTRODUCTIONHistorically the rare earths were first chemically separated from each other and purified by fractional crystallization. This slow, cumbersome, and laborious process was not suited to commercial production. Solvent Exchange (SX) technology was applied to the problem of separating and purifying the rare earth elements when it was determined in the late 1960s that there might be commercial uses for them individually. At the same time the very slow and expensive technique of ion exchange was applied either for ultra-purification of the desired “light” rare earths, or for the recovery and purification of the tiny amounts of higher atomic numbered, “heavy,” rare earths. Solvent Exchange (SX) has today become the standard for separating the rare earths across their atomic number spectrum. Whereas the separation of the light rare earths commercially may take 30 “cascades’ in a modern Chinese plant, the total separation of all of them from each other may take up to 80 such “cascades,” and is only even “practical’ with preconcentrated feed stocks, such as those produced in China by heap-leaching techniques performed in situ on very low grade radio-nuclide free ionic absorption clays.. Ultra-pure materials of all types are produced today by ion-exchange processing of ionic species already separated by solvent exchange.Hard rock deposits and refractory residues of tin mining and residues from uranium mining have been identified outside of China with very high ratios of dysprosium and other heavy rare earths to the majority lighter ones. Several issues face those who wish to process these materials so as to separate the heavy rare earths commercially:"

Jan 1, 2012

By Michel Lefebvre, André Piché

Every organization performing R&D is faced with the challenge of introducing new technologies to its operations. Difficulties must be overcome if companies are to realize the benefits anticipated from such developments. This paper outlines the difficulties encountered in transferring to operations various technologies developed at the Mining and Exploration Division of the Noranda Technology Centre. The approach used in the selection of a privileged partner for the technology transfer, the criteria motivating the choice and the process followed to establish the partnership are presented.

Jan 1, 1997

By W. T. Robson

Introduction Ground failure, violent or otherwise, is a problem to be contended with wherever underground operations are carried out. The character and extent of the failure, whether superficial or of more serious proportions, is determined by a number of factors, among which might be mentioned: the depth and dimensions of the underground workings; the types and distribution of wall rocks; structural features of the ore and enclosing rocks; the degree of metamorphism; the dip of the orebody; concentration of mining operations; the rate of mining; the history of the excavations made on the orebody in question. This last factor implies the consideration of such points as the arrangement and distribution of stoping both past and present, the current sequence of scoping, the type and effectiveness of the support used in old and current workings, and the amount and distribution of unmined parts of the lode. With such a variety of conditions, it is only natural that the situation at one place in a mine will not be the same as that obtaining in another part of the same mine and, more than likely, will be quite different in another property.

Jan 1, 1946

By M. B. Kime

"A set of experimental batch leaching tests studied the effect of pH, time, temperature, and stirring speed on the relative Cu, Co, Ni, and Fe leaching yields of an oxidized copper-cobalt ore sample in an aqueous hydrochloric acid solution. The results were statistically analyzed and modelled using the structural equation modelling method. Models showed that Cu, Co, and Ni leaching yields were strong functions of the leaching time and leaching temperature, whereas the Fe leaching yield depended on the leaching temperature, stirring speed, and pH. Under optimum leaching conditions yields were 99.8% Cu, 82.4% Co, 91.3% Ni, and 30.6% Fe.RÉSUMÉ Une série d’essais expérimentaux de lixiviation en bâchée ont été menés pour étudier l’effet du pH, de la durée d’attaque, de la température et de la vitesse de brassage sur les rendements relatifs de lixiviation du cuivre (Cu), du cobalt (Co), du nickel (Ni) et du fer (Fe) d’un échantillon de minerai de cuivre-cobalt oxydé dans une solution aqueuse d’acide chlorhydrique. Les résultats ont été analysés et modélisés statistiquement à l’aide de la méthode de modélisation par équation structurelle (SEM, de l’anglais structural equation modelling). Les modèles ont montré que les rendements de lixiviation du Cu, du Co et du Ni dépendaient énormément de la durée d’attaque et de la température de la lixiviation ; le rendement de lixiviation du Fe, quant à lui, dépendait de la température de la lixiviation, de la vitesse de brassage et du pH. Dans des conditions optimales de lixiviation, les rendements étaient de 99,8 % pour le Cu, de 82,4 % pour le Co, de 91,3 % pour le Ni et de 30,6 % pour le Fe."

Jan 1, 2017

By Clemens Kuhnert

"Nickelhütte Aue GmbH is specialized in the recycling of waste materials containing non-ferrous metals. We treat nickel, copper, cobalt, vanadium, molybdenum and precious metal containing materials like spent catalysts, ashes, dusts, grindings, liquids, slurries and sludge's as long as they contain one or a combination of the above mentioned metals. In our pyrometallurgical works we produce non-ferrous metal concentrates suitable for further treatment in our hydrometallurgical plant where we refine Ni-, Cu-, Co- and V-chemicals. Our production is based on synergy effects due to the combination of pyro- and hydro-metallurgy. As an example we can mention our heat recovery system and internal recycling of by-products. Furthermore, the use of alternative fuels instead of fossil fuels contributes to the economic and environ-mentally friendly treatment system.INTRODUCTION Nickelhütte Aue GmbH (NHA) can look back on nearly 400 years of tradition as a pyrometallurgical works and recycling company. The existence since its foundation in 1635 as a blue dye works shows responsible and successful action in the past. Therefore, we see highest customer service, minimization of interferences with nature by closing material cycles and maximized health and occupational safety protection by avoiding injuries and diseases, still as our future duties. These duties are evaluated and monitored by an integrated management system that meets the standards of DIN EN ISO 9001, 14001, 50001 and BS OHSAS 18001. We commit ourselves to the observance of all juridical and customized demands. The management and the department managers perceive their model function. We require responsible action from all employees. To protect the continuity of our enterprise, we will also perform in future continuous improvement of products and their quality, as well as steady progress in the areas of environment protection, health protection and industrial safety. Equally the effectiveness and propriety of the management system is checked and developed regularly. In order to obtain the objectives resulting from this policy, our company determines activities and measures by involving all employees."

Jan 1, 2017

By R. B. McIntosh, S Ramanchuk

A brief description is given of the process used by Sherritt Gordon Mines Limited to recover cobalt metal from nickel-cobalt sulphides. A description of the equipment with the operating conditions is presented with an evaluation of the corrosion test results for various stainless steels and other acid resistant materials for the part of the process involving the sulphuric acid leaching of nickel-cobalt sulphide slurry under air pressure. SINCE 1954 the Sherritt Gordon ammonia leach process has been used at Fort Saskatchewan to recover nickel metal, copper sulphides and cobalt-nickel sulphides from nickel concentrate produced at Lynn Lake, Manitoba. 'To develop a process for recovering cobalt and nickel from the cobalt-nickel sulphides, studies were carried out in the Sherritt Gordon laboratory and pilot plant and, late in 1957, continuous acid leaching of sulphides was started in the refinery. In September 1958 the present equipment

Jan 1, 1961