Search Documents

By Qian Liu

Mining in highly stressed ground conditions has been an increasing challenge at the Brunswick Mine. Two large regional pillars were established on the 1000 m Level to support the ground for safe extraction of the surrounding ore. The South Regional Pillar contains about 5 million tonnes of ore and the North Regional Pillar has about 3 million tonnes of ore. In the fall of 2000, mining activities were suspended following a series of ground movements around the South Regional Pillar along weak geological structures. After extensive geotechnical investigations, a decision was made to carry out a mass destress blast in the West Ore Zone (WOZ) to cut the principal stress across an area of 135 m along strike and 86 m high. At the end of July 2001, the WOZ mass blast was successfully initiated. Following this success the mine decided to take a similar approach to destressing the North Regional Pillar (NRP). The final mass blast was taken in early February 2003. Advanced blasting technologies, including state of the art electronic detonators and blast simulation, played an important role in achieving the successful blasts. The high precision of delay timing and long delay duration of the electronic detonators ensured accurate and reliable initiations of over 800 blastholes in the WOZ mass blast. Orica?s DMC_Blast (Distinct Motion Code) simulation code was used to study different blasting blocks for the desired timing in the initiation sequence. This paper describes the process of applying electronic detonators in complex blasts, and discusses how blast simulation results were interpreted to guide engineering design of the mass blasts.

May 1, 2003

By C. Schmidt, M. Kohnk, C. Siemers, J. Kiese

The application of conventional titanium alloys is limited to 550°C due to their poor oxidation resistance. In addition, severe grain growth is observed in single-phase titanium alloys in long-term runs at elevated temperature leading to a degradation of their mechanical properties. In exhaust applications in automotive or aerospace engineering, products are often manufactured by cold-deformation like deep-drawing or rolling which is normally difficult in oxidation-resistant titanium alloys due to the presence of titanium-silicides. Therefore, in the current study, titanium alloys based on CP Titanium Grade 1S (soft grade) were developed showing (1) improved oxidation resistance due to a concerted addition of silicon, iron and niobium, (2) microstructure stability by the precipitation of hafnium-silicides mainly on the grain boundaries and (3) good cold-deformation properties. The industrial production route was developed so that the new class of Ti-Si-Fe-Nb-Hf-alloys is now ready for application in exhaust systems of planes or cars at minimum 800°C.

Jan 1, 2015

By K. C. Sole, G. Robinson, M. S. Moats, W. G. Davenport, S. Sandoval

Global practice in hydrometallurgical production of copper cathode by electrowinning is reviewed, based on individual plant operating data for 2018. Data from 29 plants were collected, representing 38% of world cathode copper production. Similar surveys were carried out in 1997, 1999, 2003, 2007, and 2013. This survey includes analysis of historical and current data. Evolving trends in operating conditions and performance, as well as equipment design and process technology choices, are analysed and differences in operating practices with location are assessed. Examples of recent technology and operational choices to increase productivity, improve copper quality, and decrease electrical energy consumption are discussed. Significant project expansions, particularly in Africa, and the consolidation of numerous small Chinese operations are also presented. INTRODUCTION Global trends and operating practices in copper electrowinning (EW) in 2018 are reviewed and evaluated. Similar world and African surveys were carried out in 1997, 1999, 2001, 2002, 2003, 2007, and 2013 (Robinson, Davenport, & Jenkins, 1997; Jenkins, Davenport, Kennedy, & Robinson, 1999; Davenport, Jenkins, Robinson, & Karcas, 2001; Robinson, Garbutt, & Davenport, 2002; Robinson, Davenport, Jenkins, King, & Rasmussen, 2003; Robinson, Davenport, Moats, Karcas, & Demetrio, 2007; Robinson, Sole, Sandoval, Moats, Siegmund, & Davenport, 2013). Contributing operations included sites from the USA and Mexico (9), Chile and Peru (6), Laos (1), Kazakhstan (1), and Africa (9). Despite fewer contributions compared with past experience, this survey nevertheless represents 2018 copper EW cathode production of 1.76 Mt, or about 38% of world production of 4.64 Mt (International Copper Study Group, 2017). This drop in permission to contribute is attributed to the more competitive nature of the industry and unprecedented production pressures; furthermore, several operations in Australia have shut down, while large operations that are currently commissioning or ramping up to full production in Africa and Asia declined to participate. Of the Chinese operations, which represent an increasingly important proportion of global electrowon cathode copper, particularly in Africa, only Tenke Fungurume (Democratic Republic of Congo; DRC) participated in this survey.

Jan 1, 2019

By Kim Wiwchar, Elizabeth Mbaja, Lynne Dang, Jim Furey, Anita Marks

"Suncor Energy Inc., located north of Fort McMurray, Alberta, commenced pilot scale operation using a CPT 4’ diameter flotation column in March 2003. This larger scale trial follows two previously successful flotation column bench scale tests. They included an April 2002 trial with a 2.4” inner diameter column from the University of Alberta and a 20” diameter CPT column in August 2002. The column receives middlings stream feed from one of Suncor’s deep cone separation cells and is operated in parallel with a set of WEMCO flotation cells. The recovery, tails losses, and concentrate quality are being compared between the two systems. The column, to date, has been tested with all types of run of mine ore grades. Variables such as wash water flow and temperature, sparger nozzle size and location, sparger air/water flow rates, and column residence time has been adjusted to achieve better recovery and final product quality.Used in many mineral processing applications, column flotation is primarily used for the final stage of sulphide cleaning and flotation of phosphate or iron ore. As well, mechanical cells are often used in combination with a column to retrofit an operation and to produce a cleaner product.Initial results prove that this is the first successful application of a flotation column in an oilsand application. If viable, it will be an inexpensive process for recovery of bitumen from a middlings stream and able to produce a final product suitable for froth treatment.INTRODUCTIONSuncor’s oilsand is surface mined from the Athabasca Oilsand deposit north of Fort McMurray, Alberta. The oilsand is then mixed with hot process water (HPW) and the bitumen is slurried in a pipeline. Large separation cells as shown in Figure 1 float off the bitumen product, which is then steam or static deaerated and sent to Secondary Extraction for further cleaning. The tails stream from the cell is sent to the Final Tails Pumphouse (FTPH) for processing. The tailings flotation froth product gets recycled to the separation cell oilsand feed. The tailings are pumped from the FTPH to tailings ponds. The middlings stream is drawn off the separation cell approximately 9’ from the froth overflow level. It runs down, by gravity, to the scavenger banks for bitumen recovery. It was from this stream off of the Line 6 Separation Cell that the feed to the Canadian Process Technologies Inc (CPT) flotation column was taken."

Jan 1, 2004

By S. Kelebek, E. Yalcin

This paper reports bulk flotation characteristics of a pyritic gold ore sample from the Barry District, Quebec using isopropyl and amyl xanthates. The ore sample was highly floatable with particles showing tendencies for self-aggregation that was most apparent in the first stage of flotation. A possible reason for this is discussed. The gold concentrate grade-recovery performance with respect to the particle size is presented for the rougher-scavengers as well as for the cleaners. The effects of copper sulphate as an activator, fuel oil and NaSH as a sulphidising agent are discussed along with the recovery by size behaviour.

Jan 1, 2011

By J. Gustavsson, S. Holmin, Å. Afvander, E. Rosseland, E. Zimmerman

There are numerous advantages in replacing lead-based anodes with mixed metal oxide (MMO) coated anodes in copper electrowinning; for example, lower energy consumption, improved working conditions for operators and less environmental impact. Since 2012, Permascand AB in Ljungaverk, Sweden has evaluated Permascand coated titanium anodes in copper electrowinning pilot trials at Glencore Nikkelverk in Kristiansand, Norway. The investigation has proceeded in three different steps (Phase I, II and III). In Phase I, different Permascand coatings, electrode structures and coating methods were investigated. The results showed that improved current distribution, lower energy consumption and longer service life could be obtained with expanded mesh electrode structure in a box configuration compared to rod anodes in a single-mode construction. In addition, improved current distribution and less coating wear was found when electrostatic spray coating was used instead of brush (manual) coating. It was also found that the extrapolated service life from controlled lab experiments at 200 A/m2 was much shorter compared to what was experimentally obtained in copper electrowinning pilot trials at similar current densities. This was mainly attributed to different coating failure mechanisms in lab and industrial copper production. INTRODUCTION Traditionally lead-based anodes have been used in copper in electrowinning due to lower cost. But there are many advantages in replacing lead-based anodes with mixed metal oxide (MMO) coated titanium anodes in copper electrowinning, such as lower energy consumption, higher corrosion resistance, improved working conditions for operators and less environmental impact. Still, many facilities are using lead-based anodes, although the progression of using metal oxide coated anodes in copper electrowinning has slightly increased (Robinson et al., 2012).

Jan 1, 2019

By Douglas Brand

"The data that many mineral processing plants make use of, is provided by samples taken from sampling systems which are inadequately designed or improperly maintained, and therefore cause detrimental effects to plant operations, production planning and metallurgical accounting! Poorly designed or maintained sampling systems will likely produce low probability samples which give the operator a false sense of security of the product and the process. If data is the basis for action (Flintoff, 1992, p.2), then using the resulting suspect or bad assays by operators, control systems, or metallurgist and administration personnel will act and make decisions which may adversely affect the profitability of a processing plant. Here we will discuss some of the fundamental sampling problems, propagation of errors and a method to estimate what impact this has on an operations Net Smelter Return.INTRODUCTIONIn order to control a mineral processing plant at its best potential, it is necessary to obtain the best possible measurement results of the metal or mineral in question. The sample which is delivered to a measuring instrument, or lab, needs to be of the highest probability to be able to achieve this. This paper will discuss the effects of sampling errors on grade / recovery and grade / Net Smelter Return (NSR) and provide a method to estimate the monetary advantages of using probabilistic sampling in a processing plant.REVIEW OF SAMPLINGSampling, by definition, is the removal of a small representative portion from a total consignment, or flow, for the purpose of accounting or process control.• A sample can only be considered representative, if each and every increment collected, in each of the sampling stages, is representative.• Each particle of the sampling lot must have the same probability of being included in the final sample.• If both of the above conditions are met, then the final sample will be representative of the complete sampling lot.It is commonly known that in order to take truly representative and probabilistic sample, best practices indicate that:• The total stream should be sampled.• The sample cutter should intersect the sample at right angles to the flow.• The sample cutter should travel through the stream at a linear and constant speed and the speed deviations should be less than 5%."

Jan 1, 2016

By C. Prévost, V. Leclerc, R. Pinto, M. Ruel

"A buffer’s ability to dampen production variations is directly related to its size. Small buffers cannot handle large variations in production, resulting in production losses when their inventory is depleted or saturated. This paper presents a predictive control algorithm used to regulate the inventory in a buffer of limited size, subject to large production variations caused by an upstream batch process. The algorithm was designed to manage the acid flow rates in an acid regeneration process, servicing batch leach reactors at Rio Tinto Fer et Titane, in Sorel-Tracy, Québec. The objective was to increase production by reducing equipment downtime caused by imbalances in the acid tanks servicing the leach reactors. The controller attempts to maintain acceptable acid tank volumes by optimizing the leach reactors acid/slag ratio and reaction time as a function of anticipated acid needs, all while maintaining product quality.INTRODUCTION Some beneficiation processes in extractive metallurgy require processing bulk material in batches. Typical examples of metallurgical beneficiation batch processes are smelting, leaching, electrowinning, elution and carbon-in-pulp. These processes are often situated midstream in an ore beneficiation flow sheet and either receive or transfer ore to continuous processes. Batch processes, by their very nature, introduce large variability in the flow sheet, because they process large finite quantities of material at nearly periodic time intervals. In order to dampen variations in production, various buffers–tanks and stockpiles–are utilized to accumulate ore upstream and downstream of batch processes. A buffer’s ability to dampen production variations is directly related to its size (Phillis & Gumede, 2011). Small buffers cannot handle large production variations, resulting in equipment downtime when their inventory is depleted or saturated (Everett, 2010, Berton et al., 2013). Consequently, the batch equipment production rates must be adequately managed to minimize production losses, attributed to depleted or saturated inventories, while maintaining product quality. Algorithms that anticipate or predict future production variations are often utilized to regulate buffer inventories, subject to large flow rate variations (Salvo et al., 2002; Bonvin, 2013). This paper presents a predictive control algorithm used to maintain an acceptable volume in a spent acid tank servicing several batch leach reactors. The algorithm is implemented at the acid leach plant of Rio Tinto Fer et Titane, in Sorel-Tracy, Québec."

Jan 1, 2017

By G. M. Furnival

A PROGRAMME of structure drilling was commenced in the Southern Alberta Plains in June, 1943, for the purpose of determining the geological structure of the underlying sediments. More than 270 holes have been drilled throughout an area of some 1,800 square miles or 1,000,000 acres (see Figure 1). The Southern Plains of Alberta are covered by a mantle of glacial drift,' at places exceeding 200 feet in thickness. Only where this mantle has been dissected by deep drainage channels is bed-rock exposed to any great extent. Along such channels, surface geological mapping can be conducted to ad- vantage. Accordingly, geological mapping was commenced _in 1942 and continued each season to the present. To supplement this information, a survey of the water wells was carried on in conjunction with the mapping. However, to obtain more positive and evenly distributed structural control throughout the area as a whole and to define more adequately structural trends indicated by the preliminary mapping, it was necessary to resort to the use of drills to penetrate the glacial mantle. Various types of light drills are commonly used for this purpose and provide geological information in the form of drill cuttings, cores, drilling time rates, etc. Correlation of information is generally obtained through comparison of cored sections, drill cuttings, micro-fossils, and drilling time rates. However, in this case the holes were electrologged and correlations were made chiefly by comparison of such logs. The data so obtained is plotted and portrayed in the form of structure contour maps on recognizable stratigraphic horizons and in the form of isopach maps of the recognizable stratigraphic intervals penetrated in the holes. This method had not been widely used in Alberta previously and the technique employed was necessarily developed after the project began.

Jan 1, 1945

By B. K. Choi, G. E. Kim, S. Noh, T. K. Kim

Oxide dispersion strengthened (ODS) steel has been developed as the most prospective core structural material for next-generation nuclear systems because of its excellent high strength and irradiation resistance. In ODS steel, finely dispersed nano-oxide particles with a high number density in the homogeneous grains can be very attractive to achieve superior mechanical properties at high temperatures, and these favorable microstructures can be significantly changed using process parameters during the mechanical alloying procedures. In this study, the effects of mechanical alloying times on the microstructure of 10Cr-1Mo ODS martensitic steel were investigated. Pre-alloyed powders with Y2O3 powder were mechanically alloyed for various milling times using a high energy horizontal ball-mill apparatus (model: symoloyer CM20). Powder properties such as the mean particle size, size distribution, and crystallite size were evaluated. Uniaxial hot pressing was employed to consolidate the milled powders. The results of a microstructural observation after the MA and UHP processes indicated that the homogeneity of the martensitic structures was considerably increased with the longer milling time. It is thus concluded that the mechanical properties of the ODS martensitic steel are greatly dependent on the mechanical alloying times.

Jan 1, 2015

By P. S. Arthur, G. R. F. Alvear

Development of a new smelting process is risky. Many novel processes in the metals industry failed to fulfil the initial expectations of their inventors. Large sums of capital have been invested in technologies that either didn't provide a satisfactory return on investment, or didn't perform at all, and had to be replaced. One of the keys to success in process development is incremental scale up of the technology, with potential problems being identified and rectified as early as possible. In this way the cost of any rectification that is required can be minimized. The ISASMELTTM process was developed to maturity by Mount Isa Mines through the 1980's and 1990's using incremental scale up. Commercialization only occurred once the process had been proven on laboratory, pilot and demonstration scale over many years. As a result ISASMELTTM technology now operates successfully at numerous plants around the world. The methodical approach to development of the technology has allowed owners to modernise their existing operations or create new businesses with significantly reduced technical risk.

Jan 1, 2011

By C. O. Aksoy, H. Kose, K. Ozfirat, T. Malli, A. Gonen, S. Gurgen

In selecting mobile mining equipment, factors including availability, useful economic life, maintenance and operating costs, and spare parts availability are considered. Given these factors, trucks and shovels with different capacities are selected. Optimizing equipment for pit and hillside quarry cases, where 8% and 10% ramps are commonly in use, were examined; the effect of other mining activities such as drilling and blasting on unit cost were considered. In principle, 20 m to 25 m high benches should be economical for downhill haulage, and 7 m to 10 m low benches economical for uphill haulage. However, practice of both mining styles favours 10 m to 15 m bench heights. Hence, the analysis here was carried out with the field experience bench height range. In the study, a truck-shovel optimization was based on the movement of 5 to 20 million cubic metres (in 2.5 million cubic metre increments) of overburden stripping at the Eynez open pit mine in the Soma region of Turkey. The outcome showed that low-capacity shovels were unfavourable due to high production expectations. High-capacity shovels were also unfavourable due to health and safety issues causing high instances of impact vibration on trucks during the loading cycle and a decrease in foreseeable unit lifetimes. The number of shovel passes required to load a truck ranged from three to six. Trucks with high-capacity bodies were deemed uneconomical due to high investment and operating costs.

Jan 1, 2005

By Fraser Rowe

This paper discusses the philosophies, strategies, goals and pitfalls in automating a mine schedule. The intention of the paper is to give an open and honest view of who could benefit from moving to an automated system, what you can expect from such a system, and what you should be aware of. Many companies feel that moving to an automated mine planning solution will allow the mine scheduling engineer to push a button and walk away, but the reality is that is hardly ever the case. Part of that awareness comes from understanding what is meant by ?automated mine scheduling?, and this paper address that. By contrasting what is meant by ?manual scheduling? and ?automated scheduling? it is hoped that the reader can gain an appreciation of the entire process.

Oct 1, 2009

By M. C. Walton, W. Roelofs

ABSTRACT: In most cases, a refractory repair involves dealing with used refractory linings above shoulder height, defining these as overhead refractories. This paper details a method of personnel protection involving a low-pressure inflatable balloon system, installed to prevent the dislodgement and freefall of in-situ refractories. This system has been successfully applied to numerous types of vessels in the process industries in the last three to four years. This paper, prepared for the CIM Conference of Metallurgists held in Vancouver, British Columbia in October 2010, outlines details of the system and gives examples of successful applications.

Jan 1, 2012

By K. E. Harley, M. J. Whiting, T. J. Sabin, E. M. Ryan, J. F. Watts

"Wire and Arc Additive Manufacturing (WAAM) has the potential to enable a very significant reduction in buy-to-fly ratio compared to conventional manufacturing through the ability to build near-net shape components. Components manufactured from AA 2319 by WAAM can exhibit significant levels of porosity. There is also a variation in the physical appearance of the surface deposit sometimes found on such components. This deposit is similar to those observed on aluminium joined by MIG and TIG welding processes. It has been suggested that both the bulk porosity and the surface deposit are caused by hydrocarbon-based lubricant on the feedstock wire. An established correlation between surface deposit and porosity would offer valuable insight into WAAM products and enable early interventions in quality control or process monitoring based on visual examination. The relationship between the nature of the surface deposit and porosity has been studied for AA 2319 WAAM components manufactured using different wire batches. Evidence is presented to support the assertion that (i) there does not appear to be a relationship between surface deposit coverage and porosity, (ii) batch-to-batch variability in feedstock wire affects porosity. This study has led to a better understanding of the cause of porosity in WAAM components.INTRODUCTION There is a high cost associated with conventional, subtractive manufacturing because of the high ‘buy-to-fly’ ratio, a measure of the initial material bought compared to the material found in the finished part (Allen, 2006; Yilmaz & Ulga, 2016). A typical aerospace product may have up to 90% of the purchased billet of forging machined away which is cost inefficient and high in material waste. Wire and Arc Additive Manufacturing (WAAM) has the potential to reduce costs and lead time. Robotically controlled weld torches rapidly deposit feedstock wire in layers to build large near-net shapes with mechanical properties similar to those of conventional manufactured parts (Sequeira Almedia & Williams, 2010; Martina et al., 2012; Ding et al., 2015; Williams et al., 2015). A high level of porosity variation has been observed in aluminium WAAM parts (Cong, Ding & Williams, 2014; Gu et al, 2016) which can result in a range of material properties (Rudy & Rupert, 1970). This leads to difficulties in regards to standardisation and qualification of process and parts. In order for WAAM to be used commercially, porosity will need to be understood, monitored and reduced to a reproducible acceptable level or eliminated."

Jan 1, 2018

By R. Hans

Removal of toxic anions from aqueous solution was studied using a Magnetic Ion Exchange (MIEX) resin which is a polyacrylic, strong base resin. Gravity based settling is made more efficient due to the magnetic nature of the resin which is advantageous over conventional ion exchange resins. In addition, the magnetic microspheres of MIEX have larger surface area in comparison to conventional ion exchange resins. Over the years MIEX has been successfully used and has gained significant popularity for efficiently removing dissolved organic matter from wastewater and groundwater. In the present study the efficiency of the MIEX resin was tested for the removal of chromium(VI), molybdenium(VI), vanadium(V) and arsenic(V) anions. Effects of pH (2-10) and temperature (25oC-55oC) were examined. In general, low solution pH values were favorable for anion uptake by MIEX. Except for chromium(VI), the metal ion uptake was significantly increased by the increase in solution temperature. The adsorption data were analysed on the basis of chemical speciation and heterogeneous kinetic models.

Jan 1, 2014

By John Loui Porathur

Highwall Mining has been recently introduced in India. The first Continuous Highwall Mining extraction in India started operating at Ramagundem Opencast Project-II (OC-II) of Singareni Collieries Company Ltd. (SCCL) in December 2010. A new hybrid empirical and numerical modelling approach has been devised to design web pillars for the initial Highwall Mining sites in India, considering the complex geology, such as existence of thick seams and multiple seams in close proximity. This paper gives the scientific elucidation of a comprehensive design methodology adopted for the above mentioned Indian Highwall Mining sites. The design technology includes web pillar design for multiple seams using hybrid empirical and numerical methods, slope stability assessment, ground movement monitoring, and recommendations for conducting blasting operations in the vicinity of Highwall Mining extractions.

Aug 1, 2013

By C. E. Dowker

"IntroductionMechanization underground at the Buffalo Ankerite mine in Deloro township, Porcupine district, had reached a high level by 1944, both in equipment available, and in the use of this equipment, for all stoping operations. Power feed leyners and the latest type of stopers for drilling, slushers for moving ore and fill, and tugger hoists for all servicing, did much to halt rising stope costs, and in some cases decreased them. On the other hand, little beyond the use of mucking machines and power feed leyners had been adopted in the effort to reduce level development costs, or to increase the advance per man-shift.Faced with ever increasing level development costs, caused by rising prices of equipment and supplies, coupled with increasing wage demands for less physical effort, it was realized that more mechanization of development work was essential. The objectives of such further mechanization were:(1) Decreased development costs(2) Increased footage per man-shift(3) Less physical effort by development crews, with greater take-home pay (4) A more satisfied and stable labour force"

Jan 1, 1950

By D. Groenveld, M. Rozou

"Recent trends move towards automation, smart sensors, internet of things, powerful DCS, and more data. Are those trends already utilized in a real time production environment? Today operators still have to monitor several complex processes at the same time and predict their behavior based on an overwhelming amount of data available.The fact of the operator being overloaded and humans being unable to process multivariable problems shows the need of a tool merging essential data and providing consistent, sound decisions for long-term profitability.This paper shows a successful execution of ABB’s process improvement services in Aitik (Boliden SA), a copper mine located in Sweden. Soft sensors, fuzzy rule blocks and model predictive control were seamlessly integrated in the control system of the grinding area, resulting in proper control of mill loads and particle size without violation of any constraints.INTRODUCTIONDepending on the ore characteristics and the targeted plant capacity, the design of the grinding circuit may vary significantly. Typically, the circuit consists of several mills (rod, ball, SAG, AG) in series and/or parallel with a number of classifiers and sumps at appropriate locations. The goal of the grinding section is to reduce the ore particle size to a level that enables efficient separation between gangue and precious metals in the subsiding processing step. The trade-off between quality and quantity has to be made. It is also crucial to execute this process step at the lowest possible energy and grinding media consumption.An optimal grinding process controller must manage to maintain a given fresh feed level while keeping the product size within a given range without violating any constraints such as power, torque or load limits. To accomplish the aforementioned, it is necessary to manipulate the ore feed rate, water feed rate and the mill speed. The most significant disturbances adding another degree of complexity to this control problem are ore hardness and the amount of circulating load."

Jan 1, 2016

By J. P. Messervey

Dr. K. A. Clark: No one will doubt the statement of fact that, during drilling operations through the bituminous sand beds in the Mildred-Ruth Lakes area, the core-barrel was found to contain bitumen with minor amounts of sand instead of bituminous sand. But many will doubt the interpretation of this fact as meaning that beds of bitumen occur interstratified with the bituminous sand beds. They will prefer to hold faith in the laws of physics, which deny that sand will float on oil or that fluid under pressure will not flow away through a permeable medium, until it is proved that the appearance of the oil in the core-barrel was not due to circumstances surrounding the drilling of the bituminous sand beds. The implication of the interpretation that sand is floating on oil is clear and it is unacceptable. Bituminous sand is unconsolidated sand more' or less saturated with a viscous oil. It is as difficult to conceive of bituminous sand lying on top of a body of the viscous oil as it is to conceive of unconsolidated sand more or less saturated with water lying on top of a body of water. The only difference between the two concepts is that the oil is viscous whereas the water is fluid. Oil-soaked sand placed on viscous oil would, when released, sink through the oil slowly, whereas water-soaked sand would sink through the water quickly.

Jan 1, 1947