Search Documents

By Michael Bauer

Increases in productivity and improvements in mining occupational safety and health are intrinsically linked. Over the past years, the German Hard Coal Mining Industry has been able to accomplish both: an increase in coal production and, at the same time, a significantly reduction of accidents. This success has been achieved by advances in technology, better organization and investment in people. Since 1990 productivity has more than doubled, while the total number of accidents has been reduced by more than 90%. Further development started initially with the mechanisation of the winning and drivage technology. Innovative technology and standardisation of the mining equipment were one reason for the increase in productivity and reduction of the accident rate. Therefore this technical development was not only one important pillar of the TOM model explicated later but also the requirement for the successful development of the other pillars. In addition to further developing this innovative technology it was possible to realise procedural and organisational improvements. As a result, the above achievement is based on implementing the three pillars of the so-called "TOM" model (technology, organization, ?Mensch? = human). To increase safety, improve performance, raise awareness and change of employees? attitude, the following technical and organizational requirements have been introduced: ??New innovative technology and procedures, standardized techniques and better equipment. ??Measures to revise or redefine the organizational structure, processes and systems of work, which were then integrated into the company policy and procedures as a company management tool. ??Personnel measures (investment in people). These include, improving motivation and behaviour, training, communication to raise and to change awareness of safety issues. Success in Occupational Health and Safety is not an automatic or self-regulating process. It needs hard work to make improvements and it must be treated as a recurring cyclic process. As a result of the above, occupational health and safety has become a natural part of daily work in the German Hard Coal Mining Industry. This could only be achieved by the unconditional "commitment" of all managers and employees to the issues, coupled with discipline and responsible action. Further improvements towards the ultimate aim of "zero" accidents are only possible by mutual involvement in implementing the ?TOM? (technology, organization and ?Mensch? human) model.

Aug 1, 2013

By G. L. Palmer

"Abstract- ln 1986, anomalous sampling results for heavy minerals were obtained at various sites in Namaqualand on the west coast of the Cape Province. Drilling in 1987 at Graauwduinen penetrated up to 35 meters of heavy mineral-bearing Tertiary sands which extend several kilometers inland from the coast. The heavy mineral suite includes ilmenite, rutile, leucoxene, zircon and monazite, along with garnet, pyroxene and amphibole. Three deposits are recognized, two of which comprise the resource to be mined by Namakwa Sands Limited, a recently formed Anglo American Corporation subsidiary company.Mineable reserves in excess of 500 million tonnes have been delineated, sufficient to sustain mining for over 35 years at projected production rates. During the feasibility study, on-site investigations included test mining at various sites to assess mineability and to provide material for metallurgical testing in a pilot plant located at the site. Ilmenite produced at the mine will be smelted at a new facility to be built at Saldanha Bay . Saleable products comprise titania-rich slag, pig iron, zircon and rutile.During the exploration phase, company environmental guidelines were established and monitored. The feasibility study incorporated a Class 1 Environmental Impact Report, the contents of which were made public following the principles of the Integrated Environmental Management legislation."

Jan 1, 1994

By M. Bryson, A. E. Brady, W. Dawes, G. Beer, N. Sehlotho

Mkango Resources Limited is developing the Songwe Hill Rare Earth Element Project in southeast Malawi. Since being awarded the exclusive exploration licence for the project in January 2010, Mkango has completed an extensive work programme including detailed mineralogical studies, geological mapping, geochemical sampling and trenching, environmental and social studies, two phases of diamond drilling, and extensive metallurgical test work. In October 2012, the company announced a NI 43-101 compliant mineral resource estimate comprising an Indicated resource of 13.2 million tonnes grading 1.62% total rare earth oxides (TREO) and an Inferred resource of 18.6 million tonnes grading 1.38% TREO. The Indicated mineral resource estimate formed the basis for commencement of the Preliminary Feasibility Study (PFS). The mineralogical program identified the fluorocarbonate mineral, synchysite, and the phosphate mineral, apatite, as the primary rare earth element (REE) bearing minerals. Extensive flotation testwork conducted at Mintek in South Africa has resulted in an effective regime to increase the REO grade 2.6 times. Initial leaching testwork by Mintek identified that a selective hydrochloric acid (HCl) leach can target the gangue minerals with minimal REE dissolution. Recent testwork undertaken at Nagrom in Western Australia has expanded on this work to develop a two stage HCl leach process incorporating HCl recycling. A downstream processing route of purification and cerium rejection to produce a cerium depleted high grade REE concentrate suitable as feed to a separation facility is proposed.

Jan 1, 2014

By Sadan Kelebek, S. O. Fekete, Gerhard W. Heinrich, Peter F. Wells

"For many years, rejection of pyrrhotite at the milling stage has been a viable method for sulphur dioxide abatement. Pyrrhotite rejection options have included the use of selective pyrrhotite depressants in flotation; a depressant which has recently come into use is diethylenetriamine (DETA). This reagent has been the subject of recent research and development efforts in the processing of nickel-copper sulphide ores.In the present study, adsorption trends for DETA have been monitored under the dynamic conditions of flotation using a spectrophotometric method which has been adopted for this purpose at Falconbridge Limited. The results indicate that the adsorption of DETA is quite fast and in the majority of cases, accounts for the disappearance of 75-95 % of this reagent from pulp's liquid phase. The adsorption decreases linearly with an increase in the DET A dosage from 100 git to 600 git. The tailings produced in flotation tests were subjected to washing with deionized water at 60 °C to examine the desorption of DET A. These results indicate that the amount desorbed increases with increasing DETA dosage used during flotation but is less than 7 per cent of that adsorbed. It was found that adsorption of DETA alone, even at relatively high levels, does not always cause depression of pyrrhotite. A new combination of reagents identified in the metallurgical laboratories of Falconbridge Limited utilizes sulphur dioxide with DETA. These reagents together are capable of efficient depression of pyrrhotite on a consistent basis."

Jan 1, 1995

By A. Lopez-Valdivieso

Particle size enlargement processes play an important role in solid/liquid separation, and in beneficiation unit operations. In the latter, not only the size of the formed aggregates but also their surface properties are very important. Oil agglomeration has a special place among such processes: it is a selective process in which hydrophobic particles are agglomerated into hydrophobic agglomerates which can be recovered by flotation. This explains the broad applications of oil-assisted beneficiation processes not only in the beneficiation of fine coal, but also in agglomerate flotation of many different types of ores, and in coal/gold agglomeration.

Jan 1, 2004

By R. Scheepers

"Abstract -Mineral deposits and prospects of the Pan African Saldanian orogenic belt in the south­ western Cape Province South Africa, are reviewed. Despite the entire absence of operating base or precious metal mines in the area, this study has established at !east four metal associations that offer enticing exploration potential .The poly-phase deformed, low-grade metamorphosed volcano-sedimentary Malmesbury Group constitutes a complex, poorly understood supracrustal sequence that has been loosely subdivided into the Tygerberg, Swartland and Boland tectono-stratigraphic terranes by northwesterly trending fault zones. Syn- and post-tectonic granitoids of the Cape Granite Suite selectively intruded these terranes. Early S-types preferred the Tygerberg terrane whereas the later I-types dominate the remaining areas. Anorogenic A-type granites, however, occur in all three domains. Known metallization is directly or indirectly related to the intrusives, yet syngenetic deposits are conspicuously absent from the supracrustals. Four metal associations have been identified.•,Cassiterite-wolfrarnite (± Au, Cu, Mo, Fe-sultides) in quartz and quartz/aplite veins hosted by tourmalinized and locally greissenized S-type granite. Similar exo-granitic veins occur in proximal metamorphites.•,Juxtaposed disseminated, stockwork, breccia and vein style Cu-Mo-Fe-(Au)-sultide mineralization hosted by matie to intermediate intrusives of high K calc-alkaline, 1-type affinity.•,Cu-Mo-Au-sultides hosted by hydraulic breccia pipes, stocks and veins occurring in anorogenic A-type alkali feldspar granites and amphibole quartz syenites.•,Scheelite with minor Cu-Mo-sulfides and Au-associated with endo- and exo-skarns spatially related to I-type monzogranite, granite and alkali feldspar granite .The first three associations occur along the Yzerfontein-Helderberg-Zone, a 180 km lineament in the Tygerberg terrane, a zone exploited by syn-, late- and post-tectonic intrusives and their related mineralization. The fourth association is typical of the Boland terrane. The spatial and temporal relationships between the various metal associations is interpreted as the result of sequential intrusion of relative early high level S-type, followed by intermediate level I-type and finally anorogenic A-type granitoids during the evolution of a contracting continental margin arc and its inner arc. This plate tectonic setting suggests subduction in an easterly direction underneath the Kalahari craton. The spatial configuration of the various terranes at the present erosional levels is the result of rifting and significant differential vertical displacement following cessation of subduction, a terminal tectonic event possibly synchronous with intrusion of the A-type granitoids.Near surface preserved roof zones and cupolas of both S- and I-type granitoids in the Tygerberg and Boland terranes, respectively, render these areas extremely prospective for Sn, W, Mo and Au mineralization. The presence of intermediate to mafic volcanics, a diversity of calcareous lithotypes and favorable plate tectonic setting of the Malmesbury Group suggest potential for the thus far elusive VMS, MVT and Sedex base metal and minor precious metal deposits."

Jan 1, 1994

By Christiaan Zeilstra, Jan van der Stel, Koen Meijer, Gerard Louwerse, Tim Peeters

The steel industry is producing about 5% of the world wide CO2 emission. Therefore the European steel industry has defined a research program to reduce the CO2 emission by 50% per ton: ULCOS. Since its start in 2004 ULCOS has identified four technologies for further development. Two of these technologies which produce liquid hot metal are discussed. The ULCOS blast furnace is based on recycling of decarbonated topgas and the capture and storage of CO2. The concept has been demonstrated during three campaigns at LKAB EBF in Luleå, Sweden. The smelting reduction process HIsarna is a combination of the cyclone-technology and Hismelt. The process has been demonstrated successfully in four campaigns at a pilot installation on the IJmuiden steelmaking site.

Jan 1, 2015

By P. E. Davidson

The management of solid waste is known to be a large and increasing problem in high-population areas throughout the world. It is not necessary here to add further definition to the nature and magnitude of the problem. Instead, it is the purpose of this paper to describe a new process, called the Andco-Torrax System, which will be of use in converting municipal solid waste into useful energy forms and a granulated slag by-product. The paper includes a description of the first commercial plant for the process.

Jan 1, 1977

By J. Seo

We propose a dynamic biomechanical simulation method that uses motion capture to evaluate the risk of Work-related Musculoskeletal Disorders (WMSDs). Statistics show that WMSDs accounted for 33% of all non-fatal occupational injuries and illness in construction in 2009, and were a leading cause of temporary and permanent disability. Present methods rely largely on self-reports from workers, observational techniques, and direct measurements of motion and muscle activity to assess awkward postures, physical loads, repetitiveness, and the duration of exposure. While these methods have helped to prevent WMSDs in construction work, they may not be suitable for estimating the internal tissue loads associated with WMSDs. We propose a dynamic biomechanical simulation method to estimate internal forces and moments at each body joint of construction workers with motion capture data. Particularly, we explore the biomechanical loads by simulating active 3D musculoskeletal models based on measured postures and movements. To demonstrate the feasibility of this approach, we studied a ladder climbing task using a portable ladder under controlled laboratory conditions. Postures and motions were determined with a commercial motion capture system (e.g., VICON). The results were analyzed to investigate the feasibility of identifying risk factors based on biomechanical simulation. The results show that the proposed approach allows us to determine the biomechanical basis for WMSDs, and to identify postures and movements associated with excessive physical demands on each body joint. When combined with marker-less motion capture which is our ongoing work, the proposed approach has the potential to assess an individual?s motions and to provide personalized feedback for the purpose of reducing biomechanical loads and WMSD risk in real workplaces.

Aug 1, 2013

By B. Chambers, M. Yunovich

"Corrosion monitoring is commonly used in a variety of industries as a means of effective corrosion control programs to extend the life of the asset and ensure safe operation of the facilities. The majority of the monitoring tools have limitations and tradeoffs – e.g., sacrificing the longevity of the probe for higher measurement resolution. Linear polarization resistance (LPR) probes have the advantage of providing the operator with accurate, real-time corrosion rate data; however, the probes can only be deployed in conditions where the measured environment possesses certain minimal conductivity. In many instances, utilization of LPR probes in conditions with intermittent wetting (for example, conditions where the temperature fluctuates above and below the dew point) presents a challenge. To address this limitation, a special-design cooled corrosion probe has been developed, commercialized and integrated into the distributed control system in the plants. In addition to high-accuracy measurement of corrosion rates, the probe allows for monitoring of pitting corrosion. The most innovative feature of the probe is the cooling circuit, which brings the temperature of the sensors below the dew point, forcing precipitation of moisture and thus permitting corrosion measurements. Additionally, the probe was found to be well-suited for monitoring corrosion in crude distillation unit (CDU) overhead space, where condensation of hydrochloric acid may take place at relatively high temperatures, which would require relatively moderate amount of cooling to be imparted to the probe sensors. This paper presents laboratory-based data from a test simulating CDU refinery environment. A case study is presented to demonstrate how the cooling probe can be effectively used in the plants for corrosion monitoring.INTRODUCTIONConventional corrosion-monitoring techniques such as weight-loss coupons to assess corrosion damage are commonly used in plants1. However, the use of coupons is not only labor-intensive, but also does not deliver real-time corrosion data, thus effectively serving as a “backwards-looking” monitoring tool. Linear polarization resistance (LPR) probes have the advantage of providing the operator with accurate, real-time corrosion rate data; however, the probes can only be deployed in conditions where the measured environment possesses certain minimal conductivity."

Jan 1, 2012

By F. Mohamm

"Recent changes in regulations and scientific advances concerning selenium bioaccumulation have placed greater importance on non-biological treatment systems for selenium control. Mining wastewater contains hexavalent selenium (selenate) as the predominant aqueous species and possibly small amounts of tetravalent selenium (selenite). Non-biological removal of selenite is accomplished readily and cost effectively by ferric co-precipitation and adsorption using ferric oxyhydroxides sourced from ferric salts or iron anodes in electrocoagulation cells. Selenate on the other hand is difficult to remove. It is often incorrectly assumed that electrocoagulation is suitable for removing both selenite and selenate. Selenate removal efficiency by electrocoagulation is low and the amount of waste residue produced high. In contrast, BioteQ’s Selen-IX™ process removes selenate very efficiently and produces a much smaller amount of stable residue. The process combines selective ion exchange with electro-reduction of selenate in electrocells that physically resemble electrocoagulation cells but are designed and operated differently. This paper summarizes four years of pilot scale demonstration on a wide range of mine waters and discusses the key benefits and limitations of Selen-IX™. The pros and cons of combining ion exchange with electro-reduction in comparison to direct electro-reduction of selenate are also reviewed.INTRODUCTION Selenium in Mining and Mineral Processing Effluents Similar to sulphate and metals, selenium presence in mining and mineral processing wastewater originates from minerals contained in the mined deposits. Therefore, no organoselenium species are typically present in these kinds of waters and inorganic species including selenite (SeO32-), selenate (SeO42) and elemental selenium account for the majority, if not all, selenium present in these streams. Elemental selenium is not always present in mine water but is often contained in smelter wastewater. To comply with new environmental regulations, a successful water treatment plant must remove selenium from all these forms effectively and economically without generating by-products that are difficult to dispose of or manage. Elemental selenium can be dealt with using filtration or gravity separation in clarifiers often assisted by flocculants and/or coagulants. Mine impacted waters typically contain other forms of suspended solids which are removed from water in this way. Once the solids are removed, the selenium species that remain untreated are the dissolved forms. In mining waters this is mostly selenate with small fraction of selenite. In smelter wastewater, the majority could be selenite. It is well established that tetravalent selenium is readily removed from water by using ferric iron co-precipitation at pH > 4 (NAMC SWG, 2010). Ferric hydroxide/ferrihydrite solids act as the adsorbent for tetravalent selenium when it is in one of the ionic forms of biselenite or selenite. This treatment for tetravalent selenium is highly efficient. Therefore, tetravalent selenium removal is generally not an issue and is often easily incorporated into lime neutralization or unit operations such as electrocoagulation used for removing other metals present in mine impacted waters. Another option of dealing with tetravalent selenium is sulphide precipitation in acidic pH which produces SeS2 and can separate selenite from other metals and/or sludge produced at neutral to alkali pH."

Jan 1, 2017

By A. Giacomini, M. Nazem, E. Fathi Salmi

"Numerical simulation of collapse of tunnels in weak rocks is one of the challenging problems in rock mechanics. Collapse can impose technical and financial difficulties during the construction of underground excavations. This phenomenon, particularly in shallow excavations, may lead to propagation of a caved zone toward the surface and formation of chimney subsidence. Chimney subsidence has numerous catastrophic consequences such as the adverse environmental impacts and damage to surface structures in vicinity of excavations. Due to the importance of subsidence in civil engineering, the main goal of this study is to propose an appropriate method for preventing the formation of subsidence in shallow tunnels in weak rocks. The Dolaei road tunnel is investigated as a case study, where a large chimney subsidence has occurred. The geology of the area and the geostructural characteristics of the rock mass surrounding the tunnel are briefly reviewed in this paper. Two-dimensional as well as threedimensional numerical simulations are conducted to study the tunnel stability. Moreover, the effects of staged excavation and pre-supporting method on controlling the ground movements are studied. Outcomes of this study indicate that employing forepoling and staged excavation can be a practical remedy to control the ground movements and prevent the formation of chimney subsidence.INTRODUCTIONPredicting the formation of subsidence, mainly sinkhole subsidence over civil or mining excavations, is a very challenging task. An accurate prediction of subsidence is required for selecting an appropriate control and mitigation system to reduce the level of ground movements and its impact on the surface life (Bétournay et al. 1994; Leca and New 2007). Excavations, particularly in weak grounds, could result in surface subsidence; they modify the in-situ stress conditions as well as the hydrogeology of the area. Construction of unsupported excavations in soft soils and relatively weak rocks usually leads to the formation of a failure zone behind the face. In a very soft ground, the failure zone can extend towards the ground ahead of the tunnel face. Propagation of this zone toward the ground surface results in generation of sinkholes."

Jan 1, 2015

By G. Herget

"A brief visit to European longwall mining operations in potash showed that retreating longwall mining provides a very attractive alternative to room-and pillar mining, especially in areas with bad roof, narrow seams and areas with high ground pressures. Mines de Potasse d'Alsace, France converted all potash operations to longwall mining in 1980. Recovery rates per panel vary between 75o/~ to 85% which compares very favourably with Saskatchewan values. Ground pressure in Saskatchewan are comparable to those of some of the deposits in Europe, but the presence of water in the hanging wall of Saskatchewan orebodies has to be given serious consideration. However, given the mining experience in Saskatchewan and the improved technology f or laboratory and field investigations, a review of present mining practice in Saskatchewan is desirable. IntroductionLongwall mining is practiced widely in coal mining and allows complete mechanization. It is applicable at great mining depth, in thin seams, weak roof and has been applied recently even to coal bed s dipping more than 65 degrees. Ideally this system allows complete extraction of an orebody. However, with high mechanization and emphasis on obtaining high outputs per man shift, extraction ratios rarely reach more than 80010 per panel.France, Spain and the U.S.S.R. have had longwall operations in potash for some time and a brief description is given below. Two of the operations were visited and the Russian operation is described based on German literature"

Jan 1, 1986

By K. D. Genn, A. Mucha

This paper deals with Hilton Mines' approach to the maintenance of wear items such as truck boxes, shovel buckets, tractor pads, crawler sprocket idlers and the drop-ball. Each will be given a brief. description as to application, design, kind of materials involved and type of wear. The maintenance procedure is then outlined in terms of materials used, preliminary preparation, and welding and machining practices. The service history of new and re-paired items and the relative economics of repair vs replacement will then be presented.

Jan 1, 1969

By A. Anderko, V. G. Papangelakis, G. Moldoveanu, G. Azimi, M. Carlos

"OLI Analyzer is a software package that uses the powerful Mixed Solvent Electrolyte (MSE) model to simulate the behavior of multicomponent electrolyte solutions from infinite dilution to the limit of fused salt, and from temperatures below the freezing point up to near critical temperature of the mixture. The software also allows the creation of thermodynamic parameters for new chemical systems unavailable yet in public-domain or commercial software databanks. This communication reviews the basics of the model and provides some examples of modeling hydrometallurgical applications with emphasis on high temperature applications, including calcium sulfate scale formation in autoclaves, high temperature pH inference and iron control. INTRODUCTIONModeling of electrolyte systems has been of particular interest to various industrial processes, such as separation processes (e.g., solution crystallization, extractive distillation, seawater desalination or bio-separations), environmental applications (e.g., gas treatment, wastewater treatment or chemical waste disposal) and hydrometallurgy (e.g., pH control and neutralization, iron control, scaling and fouling of equipment). Using a chemical model, time-effective predictions of various properties of electrolytes can be obtained, which is beneficial not only during process monitoring, but also during process optimization and process scale up. As a result, pilot scale studies can sometimes be eliminated where budgetary constraints exist. Development of such a powerful model requires the use of a speciation-based model, in which solution chemistry is explicitly addressed (as compared with some models that treat electrolytes either as undissociated or fully dissociated systems), despite being computationally challenging. In addition, as a feature of electrolyte systems, speciation equilibria inherently influence the phase equilibria due to complex formation, ion pairing, and acid-base reactions. Therefore, how the electrolyte solutions behave at various conditions may differ significantly due to the non-ideality, which must be carefully addressed to obtain a model that is applicable to a wide range of conditions such as concentration, temperature, pressure and solvent system."

Jan 1, 2012

By R. H. Batey

"The process control and cost of monitoring mining slurries is normally accomplished using a continuous mass flow system, conventionally embodying a volumetric magnetic flow meter and nuclear density meter. DuPont’s Maxville Mine at Starke, Florida, USA was chosen to examine costs associated with performance of a nuclear density meter. Since it is typical of many mid-sized establishments and has a long history in their use. The published accuracy under ideal conditions of a nuclear density meter is ± 1.0%, but in practice considerable ambiguity of cost in annual production implies ± 2% at best. Using such accuracy in a 400mm (16”) pipe carrying zircon slurry at 75,000 tons/day, the cost of ambiguity, together with initial and running costs, amount to nominally $962,000 per year.Such cost leaves much to be desired. This paper describes an unique continuous, direct mass per unit volume Density Meter used for mining slurries in pipe sizes up to 1000mm (40”), which significantly reduces the cost of ambiguity of measurement and running costs. At the same time the disadvantages of nuclear devices are obviated.In an effort to reduce costs, a 400mm non-nuclear Density Meter was installed at the DuPont Maxville mine. A typical on-site accuracy can be shown to be ± 0.285%, whereby the cost of ambiguity, initial and running costs in the example above shows an annual improvement of $78,660, a reduction of over $880,000 per year.Even higher cost savings may be demonstrated with mass flow systems having gas entrainment compensation. Unlike nuclear and other inferential density meters, the signal quality of this non-nuclear Density Meter is totally unaffected by entrained gas found in mining slurries. This non-nuclear density meter is then ideally used with a vortex velocity domain sonic flow meter, and provides for the first time compensation in wet density or dry % solids, as well as wet or dry mass flow of mining slurries with entrained gas, resulting in enormous reductions in cost ambiguity."

Jan 1, 2013

By James F. Archibald

Research has been conducted for the Workplace Safety and Insurance Board of Ontario (WSIB) to characterize thin, spray-on lining materials (TSLs), as well as combinations of TSLs and conventional spray supports, and to assess their capacity for inhibiting damage created by mining-induced rockbursts. This study has been performed to assess the capabilities of such support systems for preventing rock and support material damage that often results due to rockbursting. A variety of TSLs and other spray support media were subjected to the effects of simulated rockbursting, through use of explosive detonation trials, to evaluate their damage mitigation capacity. Results have validated that TSLs and variant layer combinations may be as effective as or better than conventional support materials for mitigating rockburst or like damage in highly stressed mine environments. In civil engineering construction, and typically in underground tunneling operations where concrete linings are applied, liner deterioration is a continuing and pervasive problem that often requires expensive and time-consuming rehabilitation effort. The ability of TSLs to provide effective concrete structural reinforcement while providing sustainable resistance against underground or restricted environmental hazards, as with fires or dynamic failure events, may permit wider use of TSLs than is currently foreseen by the mining industry. Significant benefits for use of TSL materials in concrete liner rehabilitation and for concrete material protection have been assessed.

May 1, 2006

By M. D. Lawton, P. Steen

"Drilling results from the established levels at AngloRouyn Mines Limited had indicated inadequate tonnages to meet the planning schedule. It was decided to develop the main zone of the orebody below the bottom working level of the mine. The orebody dips north at an average of 50 degrees and plunges to the west at about 10 degrees. Due to the need for rapid development of this area, a decision was made to use trackless equipment.This paper describes the method used and highlights the use of small 5-ton diesel trucks as carriers for the 2-cu.yd LHD machine. The method achieved advances of about 1,000 feet per month, at a dip of 12 degrees over a length of close to 2,000 feet, using as few as 20 men per day."

Jan 1, 1971

By N. Katsikaros, N. S. ‘ Yap, B. Adaszynski

"Cyanide is a well proven, effective lixiviant that has been utilised for centuries in gold extraction processes. Despite being used in close to 90% of gold processing plants, cyanide leaching is still being scrutinised due to its toxic nature. With governments tightening the regulations on cyanide management, and recently erected sites situated closer to community and environment, leach waste and tailings treatment has become increasingly important. Gekko Systems has worked with engineering companies and directly with gold producers to provide technical services and supply complete modular cyanide destruction (detox) systems for plants leaching both run-of-mine ore and high sulphide gravity and flotation concentrates. Although similar in principle, the different materials presented unique challenges in design and implementation. Similar to designing any section of a processing plant, the development of the cyanide destruction plant design began with laboratory test work to simulate the full scale operation. This paper focusses on the laboratory test work and how other critical factors such as geographical location, logistics, and local community play a role in the process design and construction. Two design and supply cases are discussed in this paper; one treating intensive cyanidation concentrate leach tails and one treating whole ore CIL tails. Although these plants both use the SO2/O2 process, each presented different challenges in laboratory testing and plant design, resulting in variations in final implementation including reagent choice, oxygen supply, and process control.INTRODUCTIONSince 1887, cyanide has played a large part in the beneficiation of gold from gold bearing ores. Cyanide is used to solubilise gold into solution, and is typically added in excess to maintain the leaching process. Some or all the excess cyanide can often be recovered and reused in the process however chemical destruction of cyanide is often necessary to manage cyanide levels in the tailings storage facility (TSF)."

Jan 1, 2016

By L. Voisin, K. Yamaguchi, D. G. Mendoza, K. Ltagaki

The behavior of arsenic and antimony in the Cu-0 system was thermodynamically investigated to understand their elimination during a blister-making stage in copper smelting. Firstly, the phase relations in a miscibility gap composed of the liquid slag and copper phases in the Cu-0-As and Cu-0-Sb systems at 1523 K were established by a quenching technique. It was found that arsenic and antimony distributed preferentially into the slag phase in the miscibility gap. Secondly, the activities of arsenic and antimony in the miscibility gap of these systems were determined at 1523 K by using a double Knudsen cell - mass spectrometer method. It was clarified that the activity of arsenic in the copper and slag phases showed the negative deviation from ideality while that of antimony in the copper phase a slightly positive deviation. These data obtained in this study suggest a possibility to eliminate arsenic and antimony by means of over-blowing in a converter after discharging the slag.

Jan 1, 2007