Search Documents

By Otto Engel

"A multipurpose program for a hand-held programmable TJ-59 calculator and PC-100C printer facilitates the evaluation of various mineral processing tests and the calculation of mass and metal balances. Its application is demonstrated by some example problems. Detailed user instructions are given for each application.IntroductionThe program listed in Appendix I is written for a programmable Texas Instruments TI-591 PC-100C calculator I printer combination. The program is applicable for the evaluation of:1) screen analyses;2) flotation test s; and3) mass and metal balances.Each application is demonstrated by an example problem and corresponding detailed user instructions. The ""measured"" data in the examples are fictitious and do not represent a real operation.The steps in using the program are the same for each of the three types of application, viz.:1. Enter the number of product fractions and press ""A"".2. Enter the measured weights (0) of each fraction and press ""RIS"" each time. After the last fraction has been entered, the printer automatical1y displays the total weight.3. Press ""B"" to calculate the weight distribution (Y). Once ""B"" is pressed, the printer automatically displays the weight distribution of all fractions.4. If the accumulated weight distribution (EV) is also needed, press ""RIS"". The printer now displays these data. This step is optional and may be bypassed.5. Press ""2nd A"" to prepare for entering of the measured metal assay (M).6. Enter the measured metal assays of each fraction and press ""RIS"" each time. If analytical data exist for more than one metal, each data set has to be entered separately in one sequence.7. Press ""C"" to determine the ""calculated"" head assay (MA) of all fractions.8. Press ""RIS"" to calculate the metal distribution (R). Once ""RI S"" is pressed, the printer automatically displays the metal distribution of all fractions. This operation is optinal and may be bypassed if desired.9. Again press ""RIS"" to obtain the accumulated metal distribution (ER). This operation is optional and may be bypassed.10. Press ""D"" to calculate the gangue distribution in the concentrate (W). One ""D"" is pressed, the printer automatically displays the data for all fractions. This operation is optional and may be bypassed.11. Press ""RIS"" to obtain the accumulated gangue distribution (EW). This operation is optional and ma y be bypassed.12. For more than one metal, press ""E"" to clear the memory for storing the assays of the next. Then press ""2nd A"" and start entering the assays of the next metal as described previously (6 to 11). Steps 5 to 12 may be repeated as many times as desired."

Jan 1, 1982

By D. P. McDonald

"IntroductionTHE PURPOSE of this paper is to present .a summary of the evidence given before the Petroleum and Natural Gas Conservation Board in support of applications to it for permits to export natural gas from Alberta.I will attempt to be objective in my statements, despite the fact that my main interest in the hearings before the Board was to advance the interests of my own clients, the Westcoast Transmission Company, Limited.The hearing of the export applications •commenced before the Board in January, 1950, with the .application of the Westcoast Transmission Company. Joint hearings were commenced in September, 1950, and completed on December 14th, 1951. The Board heard evidence in support of six applications for export, one application to build a gathering system in Alberta, and three interveners, the .latter being the City of Calgary, the local gas companies, .and the coal interests, including both operators of coal mines and the Unions.The evidence comprised better than 8,400 pages, over two million words, and occupied 92 days before the Board.The Interest in Natural GasThe natural gas industry is one of the newer industries. It is not yet twenty years •old. In the United States, the expansion •of pipeline facilities has been phenomenal in the last fifteen years, and particularly in the last three years, when a total of over two billion dollars was invested in pipeline facilities. There are approximately 250,000 miles of gas transmission pipelines in the United States at this time, with additional lines constantly being pressed."

Jan 1, 1952

By W. W. Cummings

Canada's only current tungsten producer started up in 1962 with a small open-pit mine on the Flat River , 180 air miles north of Watson Lake, Yukon Territory. The orebody was in a contact-metamorphic skarn zone and contained about 1.5 million tons of ore grading an estimated 2.47% W03 and 0.5% copper. Near the end of the open pit , a new zone was discovered on the lower limb of the same structure, and the decision to go underground was made in 1972. The new "E Zone" contains over 4 million tons of ore grading an estimated 1.6% W03 and 0.28% Cu , and has been supplying the concentrator at about 175,0 00 tons/ year since late 1974. A continuing program of change and up-grading is necessary in the conversion from a seasonal open-pit mine with limited life to an underground operation with twenty years of reserves. Changes are necessary in plant and services as well as the mine. Also, environmental protection requirements have changed from rudimentary to rigorous over the life of the operation. This paper sums up the changes in the operation since 1971 and outlines the changes yet to come.

Jan 1, 1977

By T. W. Wlodek, Zygmunt Kowalczyk

In the period from 1946 to 1964, the annual output of co al from Polish mines increased from 4 7.3 to 117.35 million tons. In this paper, the methods of bringing about this increase in productivity through the building of some twelve new collieries (producing some 15 million tons annually) and the modernization, reconstruction and extension of some thirty-six older collieries are discussed.

Jan 1, 1967

By P. Dent

"Rare earth permanent magnets (REPM) have become virtually indispensible in hundreds of applications including aerospace, automotive, electronics, energy, medical and military. An understanding of REPMs is important since they are key drivers of demand for the overall rare earth sector. Rare earth permanent magnets stand out due to their superior magnetic properties of high induction and coercive force. We will discuss the past, current and future of the permanent magnet market and supply chain. We will summarize present and potential new nanocomposite and lower content or non rare earth magnet technologies and customer options which may mitigate rare earth usage.INTRODUCTIONRare earth permanent magnets are ubiquitous and often unseen critical components in many civilian, green energy and military technologies. They have become imbedded in applications such as hybrid electric vehicles, computer hard drives, direct-drive high power wind generators, audio speakers, motors, energy conversion systems, most weapons systems and hundreds of other uses. Several rare earth elements including neodymium, samarium, dysprosium, praseodymium, terbium and gadolinium are essential ingredients in production of the highest performance magnets available in the world today. They have enabled vast miniaturization and the significant increase in power density in hundreds of applications.China has become the dominant source of rare earth elements over the last two decades. Today, nearly 100 percent of the world’s rare earth metals and more than 95 percent of the rare earth oxides come from China. China’s near worldwide monopoly on the production of downstream materials such as rare earth oxides, metals and magnets severely impacts the supply chain in this growing global market. The past decade has seen an unmistakable trend toward increased dominance in raw material production and manufacturing by China, and a steep decline in U.S. production capabilities, most notably in the neodymium iron boron (Nd-Fe-B) market where there is currently no domestic production. This Chinese dominance is further demonstrated with over 65 percent of hard ferrite and roughly half of aluminum nickel cobalt (Alnico) and samarium cobalt (Sm-Co) production in that nation (Figure 1). In addition, China has imposed export quotas and export taxes of up to 25 percent for rare earth elements, arguably in violation of their covenants made with their protocol of accession to the Word Trade Organization. These export quotas have been decreasing steadily over the last several years in spite of rising global demand and were slashed by 72 percent in July 2010 (Bradsher, 2010) causing many recent news stories."

Jan 1, 2012

By N. Erarslan, M. Ghamgosar

With the increased use of mechanized rock excavation, there have been developed internationally a number of methods to assess the abrasivity of rock materials. These methods range from determination of abrasive and hard mineral content using petrographic thin section analysis to weight loss or rate of wear flat development on specified test pieces. The Cerchar abrasivity index (CAI) test has been widely accepted for the assessment of rock abrasiveness and is determined as the abrasion of a steel pin after scratching over the freshly-broken or saw-cut surface of a rock. Two types of testing devices are in use today: (i) the original ‘Cerchar apparatus’, and (ii) the ‘West apparatus’, which was adopted herein. The CAI is calculated from the measured diameter of the resulting wear flat on the steel pin after 10mm scratching. This test has been considered to provide a reliable indication of rock abrasiveness for isotropic rocks. However, a great amount of rocks in natureis anisotropic. Phyllite is an anisotropic and foliated metamorphic rock and various types of phyllite specimens were tested in this research. Although phyllite is a type of rock primarily composed of quartz and the expected CAI value can be high, mechanical cutting of this rock should not be very problematic compared with igneous rocks have same CAI value. As phyllite is a foliated metamorphic rock, most of the specimens split into sheets through the quartz seam by the tip during scratching normal to the axis of quartz seams. Hence, viability assessment of Cerchar abrasivity test and F-Schimazek index values for the anisotropic rocks is investigated in this research.

Jan 1, 2015

By D. W. Li

Due to the ultrasonic testing and mechanical wind speed sensor have high requirement for the environmental of the coal mine, the charge induction wind speed detection method based on wavelet analysis is proposed. The same wavelet disturbance detection method is used at a fixed distance to obtain an induction signal to obtain a pass time, and then calculate the magnitude and speed of the wind. Simulation and verification experiments show that the method has application across a wide range of test speeds (up to 60 m/s). The metal probe causes little pipeline flow field interference. The method is particularly well-suited to dusty environment, and does not cause dust deposition through long-term operation. It can be widely used in coal mines for point wind speed continuous online testing.

Aug 1, 2013

By E. B. Spice

"IntroductionExperience at Eldorado has been gained with a variety of mill feeds. That is, the actual mode of occurrence of the pitchblende varies to such an extent that gravity concentration has at times been decidedly unattractive and at others highly successful. Because of this, the type of ore necessary for economic recovery of pitchblende have become well known. Also, those types which do not lend themselves to gravity concentration have become familiar. In general, it may be said that when the pitchblende occurs free, to a large extent, from sulphides or arsenides of high specific gravity, and when the bulk of the pitchblende is localized rather than disseminated, excellent recoveries, high ratios of concentration, and good grades of concentrates , will result from proper gravity concentration. On the other hand, if the ore contains pitchblende intimately or otherwise mixed with large quantities of arsenides or sulphides, or if the pitchblende is finely disseminated, gravity concentration alone will yield high recoveries only at the expense of very low-grade concentrates and low ratios of concentration.According to Taggart, the ease with which gravity separation may be effected is determined by the value of the following ratio: []It is stated that when the ratio is above 1.75, gravity separation can be expected to be easy. Thus with pure U308 (S.G. over 9) and gangue consisting chiefly of siliceous material, the process can he expected to be entirely successful even when carried on at very fine sizes. Unfortunately, the term pitchblende covers a great diversity of material. Although some of the mineral occurs pure enough to have a specific gravity of about 7, the average is much lower than this and is probably well under 5. Some of the pitchblende particles have a specific gravity so low that gravity concentration fails completely. It may also be said that no degree of grinding will produce free pitchblende of sufficient density from such particles. This, then, represents the most important limitation to the application of gravity separation to pitchblende ores."

Jan 1, 1950

By J. R. Kish, J. Dabrowski

"The susceptibility to intergranular corrosion modes is a major technical issue preventing widespread utilization of higher strength welded AA7xxx extruded beam profiles, in the peak-aged T6 condition, in automotive bumper assemblies. A study was undertaken to evaluate the relative exfoliation corrosion resistance (ASTM G85-A2) as a function of joint design parameters, namely the base alloy composition, heat-treated condition and beam orientation after exposure to a cyclic acidified salt spray test. This paper documents the major findings extracted from this study.INTRODUCTIONBumper systems play a predominant role in the passive safety of an automobile, since they are one of the main structures for absorbing the collision energy in the event of an automobile crash. Heattreatable AA6xxx-series (Al-Mg-Si) and AA7xxx-series (Al-Zn-Mg) Al alloys, with relatively high strength, toughness, energy absorption, weldability and formability, make it possible to design costcompetitive bumper systems to crush in a controlled fashion. In this context, Cu-lean AA7xxx extrusions, such as AA7003 and AA7108, which exhibit higher strength than AA6xxx extrusion, such as AA6082, represent an attractive light weight material from which to fabricate bumper assemblies (Clausen et al., 2000; Pedersen et al., 2008; Chen et al., 2009).Arc welding is a key joining process for AA7xxx alloys within the transportation industry. A major technological issue preventing widespread utilization of arc-welded AA7xxx joints is the susceptibility to severe localized corrosion (Kent, 1970, Reboul et al., 1985; Holroyd et al., 1987). It generally occurs as exfoliation corrosion within a heat affected zone (HAZ) a few millimeters from the weld bead, or a type of stress corrosion cracking (weld-toe cracking), which initiates at the weld toe and propagates into the interfacial region between the weld bead and the HAZ (so called “white zone”). In addition to the micro-galvanic cell activity induced by the intermetallic compound constituent and strengthening particles present, there is strong evidence that macro-galvanic cell activity between the weld bead and base AA7xxx alloy may be playing a controlling role. Electrochemical profiles taken across fusion welded joints, in cross-section, during exposure to saline solutions suggest that a significant potential difference exists across the AA7xxx arc-welded joint (Shumaker et al., 1967; Grauer and Wiedmer, 1980; Tuck, 1985, Onoro and Ranninger, 1993). These studies consistently show that the HAZ and base alloy are more electronegative with respect to the weld bead (arc-welded with AA5xxx filler wire). Despite this initial important work, the majority of the recent corrosion research effort on welded AA7xxx alloys has focused on the performance of friction stir welds (Lumsden et al., 1999; Wadeson et al., 2006; Hatamleh et al., 2009)."

Jan 1, 2012

By Martin Bouchard, Bruno Paillard, Jean-Claude Dubé, André L’Espérance

"A precise analysis of the noise emitted by an aluminum plant has shown that one of the main sources of noise is the noise emitted by an exhaust stack 40 m high and 1.8 m diametre, emitting a pure tone at 320 Hz. Because a classical cost effective solution is not available for this source, active noise control (ANC) solution was investigated.Commonly available ANC systems, how-ever, are not applicable to the chimney considered because the diameter of the stack (f) is too important compared to the wave length(?)of the frequency to control. In fact, until now, active noise control (ANC) has been successfully used to reduce the acoustical energy emitted at the end of ducts in the case of plane wave propagation, i.e. ?/f< 1.7 [1,4].When f> ?/1.7, high order modes propagate in the duct and a single canal active noise control system is not sufficient.This paper presents an ANC system developed to control higher modes in a circular duct. The controller used is based on a multiple-input, multiple-output adaptive filtered X-LMS and allows up to 11 error micro-phones and controls sources. The system has been used in a laboratory on a finite duct of3.5 m long and 0.30 m diameter which corresponds to the same ratio ?/f for the real stack. The efficiency of the system with different numbers and location of control sources and errors sensors has been analyzed. Noise reduction of 15 dB(A) could be obtained with some configurations. Actually, the system is being considered for installation on the real chimney stack."

Jan 1, 1997

By Shugang Li

Coal and coal-bed methane are valuable energy resources. If they can be extracted simultaneously and safely, the triple purposes of mine safety production, new energy resource supply and environmental protection can be fulfilled. After mining, the mining induced fissure distribution feature and methane delivery behavior in overlying strata were closely related to the relieved methane degasification. Using physical simulation and numerical simulation, it was explained that the distribution feature of mining induced fissure was the Elliptic Paraboloid Zone (EPZ) in three-dimensional space. Based on the key stratum theory, the types, parameters, characteristics and dynamic evolution behavior of the mining induced fissure EPZ were analyzed. Applying environmental fluid mechanics and the mass transfer theory, the relieved methane floating-diffusion equation of the EPZ was established, and the corresponding transport process was analyzed. Using the field practice of relieved methane degasification in Tianchi Coal Mine, it explained that the mining induced fissure EPZ was the storage and delivery area of relieved methane. The degasification effect will thus be useful if the drainage system is laid in the EPZ. Such studies can provide the theoretical basis and technical support for the safe simultaneous extraction of coal and methane.

Aug 1, 2013

By G. Kipouros, M. Dadvand, A. Dadvand

"A novel methodology was developed to obtain a 3D porous layer with a high aspect ratio of porosity on a titanium electrode. The porous structure allowed more active material such as hydrous ruthenium oxide to be accommodated during the fabrication of the supercapacitor, resulting in an exceptionally high capacitance per surface area. The electrode demonstrated a remarkably high capacitance of 4,800 mF/cm2. The porous layer was composed of functionalized nanoparticles of TiO2 organized in a perfect 3D hexagonal close-packed array that resulted in a highly porous 3D structure. The layer was used as a template to electrolessly deposit a thin layer of silver prior to the electrodeposition of active material. KEYWORDS Capacitance, Porous, Ruthenium, Silver, Supercapacitor, Titanium RÉSUMÉ Une méthodologie innovante a été mise au point afin d’obtenir une couche poreuse tridimensionnelle (3D) affichant un rapport d’aspect élevé en termes de porosité sur une électrode en titane. La structure poreuse permet d’utiliser une matière plus active telle que l’oxyde de ruthénium hydraté durant la fabrication du supercondensateur, ce qui se traduit par une capacité exceptionnellement élevée par surface active. L’électrode affichait une capacité remarquablement élevée de 4 800 mF/cm2. La couche poreuse était composée de nanoparticules fonctionnalisées de dioxyde de titane (TiO2) organisées dans un arrangement regroupé parfaitement hexagonal en 3D, qui a engendré une structure en 3D hautement poreuse. Cette couche a servi de modèle pour le dépôt autocatalytique d’une fine couche d’argent avant l’électrodéposition de la matière active. MOTS CLÉS argent, capacité, poreux, ruthénium, supercondensateur, titaneINTRODUCTION There is a growing demand for integrating compact energy storage elements into electronic circuits due to the miniaturization of electronic circuits, sensors, and actuators, and the increasing importance of portable and wear-able devices incorporating more advanced electronic technologies that operate in controlled or uncontrolled environments to gather, process, store, and communicate information (Deng, Ji, Chen, & Banks, 2011; Beidaghi & Wang, 2012; Chen, Ramachandran, Mani, & Saraswathi, 2014). The manufacturing of compact energy storage elements needs to be compatible with the electronic circuit microfabrication processes. Recently, interest in integrating miniaturized supercapacitors into electronic circuits has increased due to their high charge–discharge rate and long operating life; however, ultra-high power miniaturized supercapacitors suffer from low energy density, hence requiring significant enhancement in their energy density for various applications (Deng et al., 2011; Beidaghi & Wang, 2012; Chen et al., 2014)."

Jan 1, 2019

By S P. Giambra

The 50,000-ton-per-day Concentrator and Crushing Plant, complete with its related water supply, tailings disposal and concentrate handling systems, was started up in a five-month period, with the entire plant obtaining its design capacity six months after the first mill became operational. Individual mill lines, with their spiral circuits, achieved design capacities within a week after the first treatment of ore through each mill. Construction and start-up proceeded together in many areas of the plant, and considerable organization and cooperation between the Owner, the Engineer and the Contractors permitted a smooth transition from construction to operation. PLANT DESCRIPTION THE Carol Lake Plant of the Iron Ore Company of Canada l1as been well described in various technical magazines. The purpose of this paper is to present a brief outline of the start-up of the con-centration complex. This start-up was accomplished in a period of five months, with the plant producing one million tons of concentrate and achieving its design-rated tonnage less than six months after the first ore was treated.

Jan 1, 1963

By Guillermo Turner-Saad

"Best practice in the economic evaluation of mining projects and operations is based on the integration of geological, mining, metallurgical, environmental, marketing, economic and corporate information and strategies. Fundamentally, the economic evaluation takes into account mining, blending, stockpiling, processing, smelting, refining and marketing ore resources with grades estimated by geostatistical methodologies.Nevertheless, a realistic economic evaluation consists of a concurrent and integrated optimization process that maximizes the concentrates or products of liberated and selected ore minerals from mineral deposits. The optimum solution is obtained through a trade-off among mining, blending, stockpiling and processing ore reserves with distinct mineralogy and texture characteristics. The concurrent optimization determines both the practical mining sequence of ore reserves and the dynamic and robust mineral processing flowsheet design over the expected life of mining projects and operations.A combined risk-adverse and concurrent optimization process takes into account the spatial uncertainty of the mineralogy and texture characteristics of ore reserves. Additionally, a variety of mineral processing linear, non-linear, additive and non-additive parameters modeled spatially. The spatial uncertainty of these ore reserves characteristics and parameters has a direct impact in the expected mining sequence, mineral processing flowsheet design, concentrates or products quantity and quality, and economic value of mining projects and operations.Geometallurgical domain constrained stochastic geostatistical methodologies and multivariate mathematical models are applied for spatial uncertainty modeling of ore reserves characteristics and parameters. These mathematical models correlate the mineral processing liberation and selectivity responses of the mineralogy and textures within each geometallurgical domain. These models, in turn, are defined based on results of mineral processing and environmental testwork of unbiased and representative samples chosen for their variability. These samples are selected within mutually exclusive spatial geometallurgical uncertainty domains with similar mineralogical and textural characteristics in mineral deposits.Geometallurgical domains are defined by applying and combining multivariate statistical analysis and implicit modeling methodologies. These involve determining and constraining mineral processing liberation and selectivity properties explicitly contained in the extensive and integrated exploration drillhole database."

Jan 1, 2010

By Robert A. Bosschart, Harold O. Seigel

"Most electromagnetic methods presently used in mining exploration are of the moving source type; i.e., the primary field source is moved simultaneously and in a fixed configuration with the receiver. Of the fixed-source methods, which employ a stationary primary field and a moving receiver, the Turam method is the most effective and has marked advantages over alternative electromagnetic methods. The results are little affected by topographic relief, and a high degree of resolution can be obtained because of the constant relation between source field and investigation area. Another inherent advantage of the Turam configuration is that it provides more favourable dimensional relations. Thus, the primary field attenuates at a much lower rate than in moving-source configurations and, secondly, the method is size sensitive; i.e., conductor size affects the strength of the response, which is not the case with moving-source methods. These factors result in a considerably better potential depth penetration."

Jan 1, 1966

By H. Aminian

Gold powders have many important industrial applications. In this paper the available processes for the preparation of gold nano and micron sized powders are described. The attention has been given to hydrometallurgy route and the recent works and achievements in controlling the powder morphology are highlighted.

Jan 1, 2011

By M. Potesser

Higher prices for natural gas or oil have motivated the copper industry to reexamine the modes of oxygen and oxy-fuel burner usage at operating plants. With rising energy costs and the growing importance of environmental protection, burner usage and burner operations have become the focus of several investigations and optimization efforts. One possible approach to lower energy usage is through combustion using tonnage oxygen. When such oxygen is used, the flame temperature increases and operational efficiency is improved. As well, with the correct technology, due to the presence of lower levels of harmful substances such as NOx in the off gas, there is improved environmental performance. As regards copper production, furnaces are employed for both concentrate smelting or for melting and casting operations. The use of tonnage oxygen in concentrate burners for smelting provides for a higher thermal efficiency. For furnaces employed for melting, air-operated burners may in fact have an initial advantage because a long radiant flame is typically generated, thus providing for a higher degree of heat transmission. This paper describes the new experimental burner chamber of Messer Austria GmbH which provides for testing of the combustion of natural gas with oxygen or oxygen-enriched air and the use of special water cooling ducts that simulates a metal charge during melting, The operational effectiveness of the burner is determined from temperature and off-gas analysis data. The paper also discusses future trends in burner technologies including a new patented burner. Cu2007 - Volume III (Book 2) The Carlos Diaz Symposium ou Pyrometallurgy Edited by A.E.M. Warner, C.J. Newman, A. Vahed, D.B. George, P.J. Mackey, A. Warczok Toronto, Canada,

Jan 1, 2007

By M. Aushouri, S. H. Mansouri, N. Aminizadeh

A thermo-chemical model of the Peirce-Smith copper converter in blowing the copper stage has been developed to predict the molten temperature. The key assumption of the model was that white metal and gas phases in the converter were in thermal and chemical equilibrium. In this model, the chemical reaction of white metal and oxygen was accomplished completely. So long as sulfur existed in the bath, the generation of Cu2O was frozen. The reaction rate was considered to be constant and controlled by the reacted sulfur. The converter temperature was calculated by heat balances over time. The model was validated by a detailed comparison with measured industrial data. A good agreement was obtained. The converter temperature depended on process parameters such as oxygen efficiency, molten emissivity and oxygen enrichment.

Jan 1, 2007

By S. K. Shaha, W. Kasprzak, D. L. Chen, J. Friedman, F. Czerwinski

The role of solutionizing conditions within the T6 heat treatment of the cast Al-Si-Cu-Mg alloy with micro-additions of Zr-Ti-V was assessed in terms of their influence on microstructure and mechanical properties. As a solution treatment, a single step process at 485 and 510oC and a two-step process at 510 and 525oC for varying time intervals from 0.5 to 9 h, were examined. In all cases, solution treatment was followed by isothermal aging at 150oC for 100 h. The microstructural analysis showed that the solution treatment changed the eutectic silicon morphology from needle-like, present after casting, to spherical shape in the T6 state and that the extent of changes was strongly influenced by temperature and time. The Cu- and Mg-rich phases completely dissolved during solution treatment while the Fe-containing phase, Al8Si6Mg3Fe, remained partially in the microstructure. The Ti, V and Zr containing phases, Al13Si2Ti3Zr and Al3Si26FeTiV10, present in as-cast state, were partially dissolved during solution treatment, reducing their size by 10 - 48%. The studied alloy reached the maximum ultimate tensile strength of 335 MPa and yield stress of 303 MPa for two-step solutionizing with a total time of 4.5 h. It is concluded that the two-step solution treatment resulted in higher tensile properties than the single-step process.

Jan 1, 2015

By J-P. Rossetti, A. Guerin, M. Jaboyedoff, L. Baillet, A. Mariscal, J. D'Amato, D. Hantz

"The processes leading to the fall of rock compartments from rock walls are poorly known as well as their velocity. It ensues that quantitative prediction of the failure time for a rock compartment which is presently stable, is not possible by a purely geomechanical approach. However a quantitative probabilistic prediction of rockfalls at the scale of a rock wall is possible if the spatial-temporal rockfall frequency can be determined or estimated (Hantz, 2011). For a better knowledge of failure processes and frequency, rockfalls have been detected in several rock walls, using annual terrestrial laser scanning, allowing comparison of the frequencies in different geological conditions. For one of these rock walls, the spatial detection have been completed by a precise dating of the events, using a quasi-continuous photographic survey (one photo every 10 mn), allowing the study of the influence of meteorological factors.The precise dating of rockfalls has been carried out for the Saint-Eynard cliff which towers above a residential area of the town of Grenoble (French Alps). The South-East facing cliff consists in bedded limestone gently dipping North-West and located at an elevation between 850 m and 1100 m. The surveyed zone is about 750 m large and 250 m high. Between 01/02/2013 and 26/11/2013, 65 rockfalls ranging between 0.01 m3 and 20 m3, have been detected by diachronic comparison of laser scanner data and dated by comparison of photographic images. The temperature at the elevation of the cliff has been calculated from the temperature measured (every 5 mn) at a meteorological station located at an elevation of 245 m and 2.5 km away from the cliff, using a temperature gradient of 0.003°C/m (D’Amato et al., 2014). The precipitation were measured 900 m away from the cliff at an elevation of 469 m. Different meteorological conditions have been defined: (a) “freeze” qualifies days with negative mean temperature (but with a thaw period, except for two days); (b) “thaw” qualifies days with positive mean temperature, but following a freeze day; (c) “rain” qualifies days with precipitation.Table 1 shows the rockfall temporal frequency for the different meteorological conditions. It appears that the frequency is about 6 times higher the freeze days, 2.5 higher the thaw days and 3 times higher the rain days than days without freeze, thaw or rain."

Jan 1, 2015