Search Documents

By B. W. Clyburn

"Coals from the Corporation's Lingan and No. 26 mines are classified as high-volatile A bituminous, with a very low inherent ash and containing all essential properties to provide metallurgical coal, with the exception of a high sulphur content. Only through proper cleaning at low specific gravity can the pyritic sulphur fraction of the coal be liberated to an extent where final sulphur meets coking standards. This first section of the paper deals with the operation of a Dutch State Mines heavy-media cyclone circuit to achieve an actual separation in the region of 1.30 specific gravity. A discussion of the parameter of control which must be applied along with an appraisal of the results obtained is included in the paper.Introduction Very high fluidity and unusually low ash are the outstanding characteristics of coal from Devco's mines in the Harbour seam of the Sydney coal field. However, sulphur content, mainly pyritic, ranges from 1 to 2.50Jo. To obtain the low and consistent sulphur level required in metallurgical coking coals, preparation at low specific gravity is required. Metallurgical coke is used as the fuel in an iron blast furnace. Its sulphur content largely determines the quantity of slag required to remove it and therefore influences furnace productivity and unit costs. Typical data on the various coal properties of importance in the production of coke are included in Table 1."

Jan 1, 1985

By Frédéric Flament, Luc Lachance

"The important task of metallurgical accounting that used to be done manually is being more and more automated. Currently available solutions can generate accounting reports without human intervention or almost. However, the practical conditions for fully delivering the promised benefits of those solutions are sometimes overlooked either by end-users or by integrators. The mere fact of filling reports with values satisfying several constraints such as mass conservation constraints does not, by itself, ensure a high quality metallurgical balance. Since managers make decisions based on these reports, it is logical that the metallurgical balance performance be monitored and retrofits be made if necessary. Such retrofits may involve modifications to the measurement strategy or the reduction of the spatial resolution of the material balance model. This requires an estimability and redundancy analysis (ERA) tool to assess the feasibility of the modified model. Since determining by hand the estimability and redundancy of a set of non measured and measured variables is not trivial, even for a medium-sized mineral processing plant, a dedicated ERA tool brings valuable assistance to the metallurgist in charge. The present paper aims first at explaining how a state of the art metallurgical balance is a key enabler for the adoption of a smart process plants paradigm (SPPP) in mineral processing. Then, the fundamentals behind the building of an ERA algorithm are introduced and illustrated by two examples. Finally, the role of an ERA tool in achieving state of the art metallurgical accounting and how it contributes to delivering additional value are discussed.INTRODUCTIONThe Smart Process Plants Paradigm (SPPP)Mineral processors have seen an increase lately in external pressures toward operating performance improvements. Indeed, the globalization of the mining business is a key driver to becoming more productive, more responsive to market changes, to improving corporate governance and reporting standards. Furthermore, mineral processors are also expected by their neighbouring communities to continuously improve their sustainability score. These current pressures differ somewhat from the past ones in leading to a larger than ever number of conflicting constraints that plant managers must concurrently satisfy while maximizing plant profitability. It is in turn not surprising that this context requires actions involving more real-time collaborative actions between more people in more places than ever before."

Jan 1, 2011

By Charles Tkaczuk

Key issues ? Process control is a corporate function implemented locally. ? Security and documentation is mandatory requiring standard practices. ? Publish and communicate activities (do not re-invent the wheel). ? Payback metric system for all projects. ? Partnering with vendors based on experience, expertise and joint R&D. ? Focus on phased process control projects and distribution of costs. ? Integration of services and functions. ? Application of global standards. ? Big picture application thinking.

Apr 1, 2005

By G. S. Hume

THE discovery of natural gas with naphtha in 1924 in the Upper Palaeozoic limestone of Turner Valley, 35 miles southwest of Calgary, has led to continuous developments in this field. Drilling undertaken soon after this discovery demonstrated that the anticlinal structure was in reality a major drag-fold cut off on the east side by a westerly inclined fault of large displacement. The faulted edge of the .limestone at depth determines the eastern limits of the field, which between 1924 and 1936 was shown to have a gas area 14 miles long by about 1 mile wide. Since the strata dip westerly, away from the axis of the fold, drilling becomes progressively deeper to the west and, with the advent of deeper drilling, crude oil was discovered in 1936 on the west flank of the structure but in the same porous reservoir rocks as the gas on the crest and upper parts of the fold. Since 1936, drilling has been undertaken wholly for the production of crude-oil and at present two producing areas have been found within the Turner Valley structure. The larger of these, at the south end of the field, in the vicinity of Highwood river, has a length of about 4 3/4 miles and a proved width of one mile, whereas the smaller, in the north end of the field, south of the north fork of Sheep river, has only a few producing wells.

Jan 1, 1939

By W. G. Miller, J. D. Scott, D. C. Sego

ABSTRACT An overall study was conducted to evaluate the properties and processes influencing the rate and magnitude of consolidation for oil sands fine tailings produced using different extraction processes. As part of the overall study, a comprehensive description of physical and chemical characteristics of fine tailings generated by caustic and non-caustic processes was carried out. Ultimately, the influence of these fundamental properties on the compressibility, hydraulic conductivity and shear strength properties of the fine tailings was assessed. The characteristics of the fine tailings are presented in terms of index properties, mineralogy, specific surface area, water chemistry, liquid limits, particle size distribution and structure. A difference in water chemistry was concluded to be the cause of substantial differences in particle size distributions and degree of dispersion of the comparable caustic and non-caustic fine tailings. The degree of dispersion was consistent with predictions for dispersed clays established by the sodium adsorption ratio (SAR) values for these materials. A linear variation of increasing dispersion with increasing SAR up to a SAR value of about 40 has been suggested, above which fine tailings are completely dispersed. The observed dispersed or flocculated structures (viewed using a scanning electron microscope) supported the predictions based on SAR values.

Jan 1, 2010

By J Petrolito

"To improve the economic and environmental performance of underground mining operations, it is common practice to return the metallurgical waste material underground as backfill. This is called hydraulic backfill and is used to fill the mined-out areas not exposed to further mining. To provide mechanical support for underground mining a cemented backfill is normally used. Since its introduction, cemented backfill has allowed mining companies to increase their ore extraction and improve working and environmental conditions. However, cemented backfill represents up to 50% to 85% of the mine’s operating cost compared with 5% to 10% for hydraulic backfill.These economic pressures have led mining companies to carry out research into the partial or total replacement of cement using a variety of alternative materials. The materials are generally site-specific materials, readily available, and cost-effective relative to cement. Such investigations have led to reduced cost of many backfill mixes while maintaining, and in some cases improving, the physical properties of cemented backfill. However, in most cases, cement still remains an integral part of any binder combination. This can be attributed to the alternative binders investigated being either non-binding materials or capable of generating only low-strength backfills, except when used in conjunction with cement.This paper provides a historical review of backfilling binder materials and their characteristics. In particular, it reviews the many alternative materials that have been proposed to either partially or fully replace Portland cement as the main binder."

Jan 1, 2005

By D. L. Cluff

Ventilation Air Methane (VAM) is a high volume low concentration methane source. The capture or use of methane from VAM is challenging, which results in the routine discharge of methane into the atmosphere. Mitigating VAM has the benefits of providing an energy source and reducing the atmospheric Greenhouse Gas (GHG) burden. The GHG radiative forcing effect of methane is 17?23 times as potent as carbon dioxide on a 100-year time horizon. Thus, any reduction in atmospheric methane would be beneficial. The calorific value of methane is 55.5 MJ/Kg; therefore, a 100 m3/s flow with VAM concentrations from 0.1?1% can provide 3.8?38 MW of exploitable power. Strategies to mitigate VAM such as: Thermal Flow Reverse Reactors (TFRR), Catalytic Flow Reverse Reactors (CFRR), Lean Burn and Catalytic Gas Turbines, Biothermica Vamox®, Megtec VOCSIDIZER©, and Vamcat? are briefly reviewed. The review of VAM mitigation technologies reveals disadvantages such as the need to maintain a minimum internal heat capable of oxidizing the methane. This requirement uses all of the available methane up to the point of reaction sustainability and up to half at the highest methane concentration in VAM. Some systems may introduce a pressure drop to the ventilation system, which would impinge on the existing ventilation system design. These impediments necessitate the development of a more amenable technology. In the proposed system, gas turbines (GT), coupled to a combustion chamber with an external fuel supply, assist the combustion of the VAM. The combustion-chamber coupled system provides electricity, while the heat contained in the GT exhaust gases increases the temperature of the VAM, encouraging the development of a flame inside a combustion chamber. The flow from the combustion chamber streams through a primary air/fluid heat exchanger capable of producing steam of a high enough quality to generate electricity using conventional steam turbines. The residual heat after primary extraction, directed through other equipment, provides additional heat based products such as industrial scale dry air, chilling by an absorption chiller or hot water. The overall design of the system is scalable for low to high VAM flows or variations in concentrations and is capable of providing the company or community with heating, chilling, hot water, electricity or motive force as needed by the particular site or community. The Multi-generation system uses heat from three sources to provide clean efficient energy while mitigating the atmospheric emissions of methane. These sources are heat from the GT, often considered waste heat, heat from fuel injected into the igniters and heat from the VAM. The opportunity to collect carbon credits may improve the economics. In order to design a system with this capacity, a detailed analysis of the combustion characteristics of three separate flows is required. VAM is the main airflow, having the highest volumetric effect, while the GT exhaust and the additional fuel added to the hot exhaust flow of the gas turbine are lower flows, but have a higher velocity and temperature. The aim of the modeling undertaken in this work is to establish the combustion dynamics, degree of pre-heating required and the geometry essential to the design of combustion based VAM mitigation multi-generation systems.

Aug 1, 2013

By M. Fan, M. Mankosa, G. Luttrell

"Column and other non-conventional flotation approaches continue to provide benefits where conventional flotation processes have exhibited limited success. This is particularly evident with respect to flotation of ultrafine and coarse particles. Advancements in air sparging technology have provided the ability to produce finer bubbles than previously possible. The generation of finer bubbles coupled with the froth washing capabilities of a flotation column has demonstrated improvements in ultrafine particle recovery while simultaneously producing a high-grade float product. On the other side of the spectrum, the use of these sparging technologies while applying flotation fundamentals to a fluidized-bed reactor has increased the maximum floatable particle size up to and in excess of 3 mm. Benefits of higher recoveries and reduced reagent consumption have resulted from the use of these technologies. An additional benefit includes a reduction in plant grinding requirements. As such, this paper describes the application of Cavitation-Tube sparger technology and fluidized-bed flotation (HydroFloat). A review of data from industrial and pilot-scale applications is also provided.INTRODUCTIONConventional (mechanical) froth flotation is considered the workhorse of the minerals processing industry. This low-cost process makes it possible to selectively recover minerals by exploiting the difference in surface characteristics (e.g., wettability) of the valuable component and the waste material. Unfortunately, the upper particle size limit for flotation rarely exceeds 0.600 mm, and is typically maintained at less than 0.300 mm for most industrial applications. For many commercial base metal plants, the particle size range for optimum recovery is typically between 0.01 and 0.1 mm (Lynch et al., 1981). This finding is not novel. In fact, the effect of particle size on flotation recovery was studied as early as 1931 by Gaudin et al. who showed that coarse (+0.250 mm) and extremely fine particles (-0.010 mm) are more difficult to recover than particles of an intermediate size. The loss of recovery is due to inherent limitations associated with the flotation process, including bubble-particle adhesion and collision, detachment, buoyancy, and transport."

Jan 1, 2010

By Clifford S. Gibson

A year ago a paper (1) was presented at the Annual Western Meeting of the Institute regarding silicosis in Ontario mines. It described the whole problem as we see it and discussed the means of prevention. The work and aims of the Technical Silicosis Research Committee of the Ontario Mining Association, and of the Committee's field engineer, were fully described also and it is suggested that reference be made to this paper in order to have a better understanding of the observations which are presented now. These observations enlarge upon parts of the dust control measures already discussed and tell of general progress in the past year. They concern fifty properties, the majority of the operating mines, which vary in size from the hopeful prospect to established producers yielding 11,000 tons of ore daily. Most of these are gold mines; a few copper-nickel. The ores range from heavy sulphides to siliceous materials and they are mined by many methods from varying types of deposits. The majority of the latter are steeply dipping and all are found in Precambrian host-rocks. Up to the present, die greatest depth to which mining has penetrated is 6,400 feet.

Jan 1, 1939

By Zoltan F. Oszter

The design of belt conveyors is a well-known procedure and related formulae can be found in any handbook dealing with materials handling. Belting and conveying equipment manufacturer's catalogues and design manuals offer a wide range of detailed information which can be applied to most of our conveying problems. The aim of this paper, however, is to investigate the design of a specific type of belt conveyor, namely the long horizontal, or nearly horizontal, type. (The undulating type, with moderate lifts and drops, can also be included in this category.) Most of the long overland conveyors carrying ore from pit to processing plant, or those carrying over-burden to the disposal area, fit this description. A critical appraisal will show that reasonably accurate results can be obtained when tl1e familiar horse-power formulae are applied to this type of conveyor. The progress and new developments in the design of belt conveyors, which have resulted from the extensive research done in the past decade, will also be explored.

Jan 1, 1962

By George F. Bassett

"More will be expected from the mine or metallurgical plant electrical system in the late 70's and 80's in terms of energy conservation, reliability and fire prevention. Increased electrical loads 1•equired by larger arc furnaces, higher-horsepower motors for mine hoists and pollution control fans, and greater use of electrical heating will have to be supplied. Computers and sophisticated instruments will be used more extensively and have less tolerance for electrical fluctuations. More extensive control and monitoring systems will be required to increase production and minimize operating and maintenance costs. Changing energy costs will prompt design engineers to investigate in-plant generation, particularly where sites are remote from existing utilities lines or steam from turbines may be used in the process. Some utilities are requiring industries to increase their power factor to above 90% ; others are requiring stricter control of voltage flicker from arc furnaces and harmonics from rectifiers. There is a trend to AC with solid-state cont1•ols instead of DC for large cranes."

Jan 1, 1976

By David Rahal, Des Erasmus, Ken Major

"Over the past twenty years there has been an increased emphasis on fine grinding in the minerals industry. This spurred the development of a range of new fine grinding equipment in the 1990s. At that time, the Knelson-Deswik mill was developed in South Africa for the pigments industry.Knelson Milling Solutions currently offers a wide range of laboratory, pilot and production scale mills. These mills bridge the gap between traditional low speed vertical mills and the high speed horizontal mills (tip speed < 3 and > 15 m/s respectively). They are designed to run at tip speeds between 10 and 12 m/s and are capable of operating with very dense grinding media. The result is a power intensity that is higher than the low speed mills and overlaps that of the high speed mills. This allows the mill to be customized for a wide range of grinding applications.A case study at Aquarius Platinum’s Kroondal Mine shows that the Knelson-Deswik technology can produce a consistent product size despite feed variations. It also shows that the throughput was proportional to the slurry density at Kroondal. The case study identified increasing the slurry density as a process change that can increase throughput and reduce the specific energy consumption.INTRODUCTIONThe increasing complexity and finer grain sizes of modern ore bodies have increased the importance of effective mineral liberation in obtaining acceptable grades and recoveries (Jankovic, Valery and La Rosa, 2003; Lichter and Davey, 2006; Napier-Munn, Morell, Morrison and Kojovic, 1996). This trend has increased the significance of fine grinding technology because the input energy increases exponentially as the required product size decreases from 100 to 10 microns (Gao and Weller, 1993a).The US Department of Energy recently provided the context for the potential energy savings in the US Mining Industry (BCS, 2007). They reported that grinding consumes approximately 494 TBtu/year. This was over double the consumption of the second highest equipment category, diesel materials handling systems (211 TBtu/yr). The proportion of grinding energy allocated to fine grinding can only be expected to increase as finer ore deposits are mined. It is therefore critical that fine grinding efficiency continue to improve through the selection of appropriate equipment and the development of best practices for existing applications."

Jan 1, 2011

"At a current mining rate of 3,750 tons per day, La Mine Doyon is currently the largest gold mine in Canada. La Mine Doyon is an open pit gold mine located in the Abitibi area of Northwestern Quebec. The project is a joint venture between Soquem, a Quebec Crown Corporation in the resource development field and Lac Minerals Ltd., a publicly-held, resource development company. Lac Minerals is the managing company and operator of the project.Doyon went into production in 1980 on a very limited basis at 600 tons/day, and has seen a step wise increase to the current rate of 3,750 tons/day. Initially, all the ore was processed at Noranda Mines, Horne Division as flux for the copper smelter. The East Malartic Mill in Malartic was then upgraded and began processing Doyon ore. The third step in the progressive increase of throughput was the commissioning of the Doyon mill in November of 1982. Doyon ore is currently being processed at all three locations.During 1983, an exploration ramp was driven to explore the ore below the ultimate pit depth. Current plans indicate the sinking of a shaft and the commencement of underground mining during the next 2 or 3 years.Since its humble beginning, La Mine Doyon has always been a success; ore reserves have been extended to the east and the west and will soon be confirmed at depth, the mining and processing rates have been increased 6 fold, and the recovery has been increased from a designed recovery of 85% to over 95%. The intent of this paper is to trace the history and reasons for these rather dramatic improvements."

Jan 1, 1984

By M. Holmes, R. Molnar, E. Norton, K. Baxter, J. Riordan

The Boleo Copper-Cobalt-Zinc-Manganese Project of Baja Mining Corp. is situated adjacent to Santa Rosalia on the Baja Peninsula of Mexico. The El Boleo ore is a mixed oxide-sulfide deposit with major values in copper, cobalt, zinc and manganese. The metallurgical process designed to treat the El Boleo orebody involves a sulfuric acid leach in seawater using oxidative and then reductive leaching to maximize metal extraction. The leach solution is separated from the barren solids via counter current washing through a series of high rate thickeners. Copper is recovered using conventional SX-EW processing as cathode. Zinc and cobalt are extracted from the copper SX raffinate after iron and aluminum precipitation. The CSIRO DSX solvent system (Versatic® 10 and LIX® 63 mixture) are used in this extraction. Manganese remains in the DSX raffinate and is recovered by soda ash addition as a high quality manganese carbonate precipitate. Zinc and cobalt are acid stripped from the loaded DSX solvent. Zinc is then re-extracted away from cobalt using Cyanex® 272 extractant and stripped into a highly concentrated strip liquor (+100 g/L Zn) and directed to either a spray dryer or a granulator for production of zinc sulfate monohydrate. The zinc solvent extraction raffinate, containing cobalt, advances to another SX circuit using Cyanex® 272, for the recovery of cobalt as cobalt cathode. In this paper, the detailed results from bench and integrated pilot plant testing for zinc recovery from the El Boleo ore will be described. The results of this testing are currently being used to engineer the commercial plant at El Boleo.

Jan 1, 2008

By M. Dotto, T. G. Joseph, M. Curley

"Equipment selection is a key decision in mine planning. Equipment size affects decisions from pit size to the total operation cost. Particularly when replacing haulage fleets for long-life surface mining operations, mining operations focus solely on haulage productivity. Road width and specifically ramp width are significantly affected by an increase in hauler size in terms of overall strip ratio through required highwall set-backs or sterilizing of lower ore access due to required overlying ramp fill structures. In addition, in light of ever increasing regulatory and reporting emissions requirements, bigger equipment may not translate into lower emissions per tonne moved. This study analyzes hauler-scale impacts on aspects not currently incorporated into conventional mine planning, including expansion of roads to accommodate larger equipment, road layer thickness variation depending on hauler size, and fuel consumption and emissions. Results indicate that such relationships have a large impact on cost. Therefore, an expanded consideration of the capacities of increasing equipment size in mine planning is highly recommended. ¦ KEYWORDS Equipment selection, Grade resistance (GR), Haul road, Haul truck, Mine planning, Payload, Rolling resistance (RR), Total resistance (TR) RÉSUMÉ La sélection du matériel est une décision importante dans l’aménagement des mines. La taille de l’équipement a une incidence sur la prise de décisions, depuis la taille de la fosse jusqu’aux coûts totaux des activités. L’exploitation minière se concentre uniquement sur la productivité des moyens de transport, particulièrement lorsqu’il s’agit de remplacer les parcs de camions de transport dans les exploitations à ciel ouvert à longue durée de vie. La largeur des routes, et spécifiquement la largeur des descenderies sont considérablement affectées par une augmentation de la taille des camions de transport en termes du coefficient global de recouvrement qui dépend de la taille requise des parois (si les descenderies sont agrandies, les parois devront être creusées de haut en bas afin d’agrandir la taille du fond de la fosse). Il faut aussi pouvoir procéder à l’excavation des gradins les plus profonds de la mine et ainsi préserver l’accès à cette zone, ce qui pourrait devenir difficile si la quantité de stériles utilisés pour la structure des descenderies augmente et s’ils occupent une trop grande partie du fond de la fosse. En outre, au vu des exigences de plus en plus strictes en matière de réglementation et de déclaration des émissions, un équipement plus volumineux ne sera pas nécessairement synonyme d’une réduction des émissions par tonne déplacée. Cette étude analyse l’incidence de la taille des camions de transport sur des aspects actuellement non intégrés dans l’aménagement classique des mines, notamment la création de routes permettant le passage d’un équipement plus volumineux, la variation de l’épaisseur de la couche d’asphalte des routes en fonction de la taille des camions de transport, ainsi que la consommation de carburant et les émissions. Les résultats indiquent que ces relations ont des répercussions importantes sur les coûts. Ainsi, on recommande d’accorder une attention accrue aux capacités d’augmentation de la taille de l’équipement dans l’aménagement des mines. ¦ MOTS CLÉS aménagement des mines, camion de transport, charge utile, résistance au roulement, résistance due aux rampes, résistance totale, route de transport, sélection du materielINTRODUCTION Over the past five decades, the mining industry has progressively attempted to increase production rates through the use of larger haulage equipment. Each new generation of mine is designed to operate with the most recent and often bigger equipment iteration, while older mines are re-evaluated to keep pace with upgraded mixed fleets. Whereas production gains are often realized with larger equipment, there are additional aspects to consider when evaluating the feasibility of mo"

Jan 1, 2019

By S. Banisi, J. Marois, A. R. Laplante

"This paper compares the behaviour of gold and ore in the grinding circuit of Hemlo Gold Ltd. Particular attention is given to grinding kinetics, classification behaviour, and liberation. For grinding kinetics, laboratory grinding of gold flakes and silica, 840-1200 um in size (14/20 mesh), was also performed to provide a standard for comparison and to study in a controlled environment the mechanisms of breakage, folding, smearing and impacting.Grinding kinetics were characterized at laboratory scale with breakage and selection functions. The breakage function showed that 75% of gold disappearing from the 840-1200 um class reported to the 600-840 um; this figure is much higher than for silica ( 46%) or most other minerals, and implies that comparatively fewer fine fragments are produced from the breakage of gold flakes, on account of gold's malleability. The selection function of silica was four times that of gold. At plant scale, the ratio of the selection function of ore and gold increased from 6 for at 50-100 um to 20 at 500-1000 um.Observation of original flakes and their fragments with the scanning electron microscope showed that the main mechanism of ""grinding"" from the 840-1200 um to the 600-840 um class was folding rather than actual breakage. This was confirmed by a measure of individual flake weight. The postulated breakage cycle is that relatively globular flakes become increasingly serrated through grinding; they can then regain their original shape through folding and reflattening into cylindrical and spherical shapes, as the majority does; however, some fragments will at this point undergo actual breakage. Photographic evidence is presented to support the proposed mechanisms.Smearing of gold unto silica was observed when silica was ground after a gold, and embedding of silica into gold flakes when gold was ground after a silica. Both mechanisms occur whenever gold and harder minerals are jointly ground, and result in ""unliberation"" of gold. It is postulated that smearing of gold onto other minerals plays an important role in explaining how gravity recovery can increase overall gold metallurgy, especially when used ahead of flotation.Classification of gold in the primary hydrocyclones takes place at a much finer cut-size than ore, 20 vs. 57 um. This and the slower grinding kinetics result in high gold circulating loads in the primary loop, 6700%, and a gold content in the primary cyclone underflow (PCUF) is twenty four times that of the ore. The gold size distribution for primary cyclone overflow is much finer than that of the ore, although they are essentially similar in the PCUF.Liberation, or more accurately ""gravity recoverability"", was assessed with a 7.5 cm (3"") Knelson concentrator. It varied between the thirties for the primary mill discharge and two cyclone overflows, to highs of 89 to 92% for the PCUF and secondary mill discharge, 89 and 92%, respectfully."

Jan 1, 1991

By Harry Perry

By 1980, the free world's need for economic sources of energy is expected to double. As a result, there will be a tremendous potential for all energy sources working together to supply the demand. For coal to continue its dominant role as a low-cost energy source, means must be found for it to meet the challenge of nuclear power and to overcome obstacles placed on its use by air and water pollution regulations. As the more limited reserves of gas and oil diminish, economic ways are also required for converting coal to synthetic liquid and gaseous fuels, and to chemicals, thus resulting in optimum utility of the most abundant low-cost fuel resource. The means for accomplishing these ends can only come about by a vigorous research and development program. Successful efforts by industry and government working together, both in America and abroad, will assure the continued use of coal to meet the world's energy demands. This paper discusses the emerging patterns of energy sources throughout the world and the role that research and development on coal will play in supplying future energy requirements.

Jan 1, 1967

By H. Agnerian

"A survey of 925 mineral property transactions worldwide was carried out between 1987 and 2004. These mineral properties with reported Mineral Resources include 457 gold properties, 322 base metal properties, and five platinum group element (PGE) properties. Based on constant Canadian dollars, the results of the survey indicate that:• In general, unit metal values in the ground (e.g. $/oz Au or $/lb Cu) have kept pace with the changes in the respective metal prices during the period of the survey.• A general decrease in unit gold values in the ground has occurred from about $57/oz Au in 1987 to about $11/oz Au in 2002 for Canadian mineral properties, with the exception of a peak of $58/oz Au in 1996.• A similar trend for mineral properties has occurred in the United States, but with lower unit values, in the range from $1/oz Au to $10/oz Au during the last three years of the survey. • Unit metal values in the ground for gold properties in Canada were higher than for those in the rest of the world.• Unit metal values in the ground for copper properties in Canada were in the mid-range compared with other countries in the rest of the world; the United States and Australia were higher and Latin America, Asia, Africa, and Europe were lower than in Canada.• Unit metal values in the ground for zinc properties in Canada were also in the mid-range compared with other countries in the rest of the world; Latin America and Europe were higher and the United States, Australia, and Asia were lower than in Canada.• Unit metal values for nickel properties in Canada were highest compared with other countries in the rest of the world, followed by the United States, Australia, Africa, and Asia.• Gold values in the ground in Canada have ranged from 6% to 14% (with an average of approximately 10%) of the gold price.• The unit values of base metals in the ground have been in the order of 2% of the quoted metal price, during the period of the survey."

Jan 1, 2006

By H. P. Kang, Y. J. Feng

The hard roof in underground coal mines is generally considered as a main cause that induces disasters in working faces and entries, such as rock burst and windblast. Hydraulic fracturing technology is an effective approach to weaken hard roof to reduce ground pressure and control rock burst. The state and achievements associated with hydraulic fracturing technology applied in Chinese coal mines are summarized in this paper. Theories related to hydraulic fracturing are of the essence in fracture design to determine the fracture initiation and propagation pressure and predict the geometry and the characteristics of hydraulically induced fractures. Initially, theory of elasticity was employed to determine the breakdown pressure for a vertical borehole where the rock medium is assumed to be elastic. However, porosity and pore fluid have an influence on the borehole breakdown pressure, and then the poroelasticity theory was applied. Arbitrary deviated boreholes in practice are rather common and the maximum tensile stress criterion was employed to determine borehole breakdown pressure. The effect of natural crack in the rock medium on the initiation pressure has been taken into consideration through fracture mechanics. Meanwhile, considerable achievements have been made on hydraulic fracturing tools and equipment, and a set of mature hydraulic fracturing technologies for hard roof control are available. Some comprehensive investigations on the hydraulic fracturing for hard roof weakening are presented, and successful field applications in the Jincheng and Luan coal mining districts are introduced. Finally, the unsolved problems related to hydraulic fracturing are also put forward.

Jan 1, 2015

By A. H. C. A. Zimmerman

WE have just heard what must be regarded as a thoughtful, constructive and somewhat painful analysis of the financial function of our industry. While thinking about this, it is interesting to reflect on the conditions which have stunted the growth of the financial side of our affairs. Mining must be regarded as a wealthy business. •while immeasurable grub takes and development budgets have been lost, there can be little argument that a productive ore-body nearly always produces the type of wealth that breeds some extravagance. I recognize that this statement can be attacked from many sides, but an historical comparison with a commercial enterprise involving similar investment will demonstrate what I mean. However, these old times are be-ginning to disappear for a variety of reasons. High amongst these are: ( l) Increased costs of exploration. (2) Remoteness of many new finds. (3) Fixed or declining metal prices (particularly when expressed in constant dollars). ( 4) Constant demands for higher wages.

Jan 1, 1962