Search Documents

By Tonegato S, Wood M

The lack of objective data on roof bolting machines, bits, rods and overall system has created the need for an objective assessment of roof bolting. This work outlines a test rig for such objective assessment of component parts of the roof bolting system.

Jan 1, 1986

Accounting for borehole damage in analytical modelling of explosively generated stress waves is important for predicting the finer details of the stress wave patterns observed in the field. The classical Sharpe's [19421 concept of an effective borehole larger than the initial borehole diameter has been widely accepted to explain material damage around a borehole. A new analytical model based on dynamic compaction is advanced to predict far-field stress wave patterns. This model supports field data corresponding to reduced frequency of oscillations and increased damping. The present model recovers the earlier result when compaction around the borehole representing borehole damage is ignored.

Jan 1, 1990

A failure criterion for coal is proposed in which a distinction is made between brittle and "pseudo-ductile" failure. This criterion is then used in the development of new equations for coal pillar strength, including a transition from brittle fracture to pseudo-ductile yielding. In addition, equations are obtained which allow the äritical minimum pillar dimensions to be calculated to avoid "catastrophic" and "ultimate failure". The use of these formulae is then demonstrated by comparing the results with pillar case histories derived from the literature.

Jan 1, 1986

By Sandenbergh RF

The debate on the mechanism of adsorption of gold and silver di-cyanide onto activated carbon could be divided into two schools of thought. On the one hand, it has been proposed that the combined effects of electrostatic and chemical interaction between the activated carbon surface and adsorbing gold di-cyanide anion results in the adsorption of the latter. On the other hand the `ion-pair' adsorption reaction mechanism has been vigorously advocated as the dominant mechanism responsible for the adsorption of gold di-cyanide onto activated carbon. It is maintained that gold is adsorbed onto the carbon surface as the neutral ion-pair [M"+][Au(CN)z ]". Adsorption is viewed as the result of mainly the chemical interaction while electrostatic interactions are neglected. The validity of the `ion-pair' adsorption mechanism may be challenged on a number of counts. However, the alternative mechanism (based on aqueous surface chemistry principles) has not gained general acceptance yet, because it has not been applied widely enough to explain the different adsorption phenomena associated with gold di-cyanide on activated carbon. In the present study the case in favour of an adsorption mechanism based on general aqueous surface chemistry principles is presented. A model framework is developed for the adsorption reaction mechanism of gold di-cyanide onto activated carbon which incorporates the effects of chemical and electrostatic interactions between the dissolved species, the aqueous solution and the carbon surface. This model is then employed to explain a wide variety of reported adsorption phenomena for gold di-cyanide on activated carbon, such as the effects of pH, the adsorption of different metal cyano complexes, ionic strength, and type and concentration of cations in solution. In addition the effects of cyanide and dissolved oxygen concentration were investigated. No ready explanation, in terms of aqueous surface chemistry principles, is yet available for the switch in adsorption behaviour that agrees with ion exchange to ion-pair adsorption with increasing ionic strength.

Jan 1, 1997

By P Scott

Kaltim Prima Coal, an open cut coal mine located in Sangatta, East Kalimantan, Indonesia, operates two deep pits and two shallow pits with a truck and shovel operation. KPC produced 17 Mt of coal in 2002 by removing 120 Mbcm overburden. Geochemical investigations have indicated 20 per cent of total waste rock is potentially acid forming; ie it has the potential to create acid mine drainage (AMD). In the early years of the KPC operation, the presence of AMD had been observed in the mined out areas and in the waste rock dumps as a result of sulfidic waste rock exposure. A strategy for management of AMD from waste rock was implemented involving: sampling, analysis, modelling, selective handling and validation of final dump covers. Samples of the waste rock lithologies are collected from exploration drill holes for geochemical analysis to determine their acid generating potential. The geochemical database is used to develop the waste rock model for the life of mine pit areas. The acid forming and non-acid forming waste rock is delineated for each mining bench area for selective handling and placement within the waste rock dump during the operational stage. Each mining bench is sampled and assessed to validate the model predictions. The final dump cover is sampled to meet strict Quality Assurance requirements to ensure non-acid forming waste material is used in the outer cover of the dump. The geochemical investigation of the waste rock is integrated with mine planning to design and construct the waste rock dump to minimise the risk of generating acid. This process links the exploration stage, operation stage, and rehabilitation stage for each Pit area. The paper briefly reports the waste rock characterisation, waste modelling and strategies used for management of acid drainage by KPC.

Jan 1, 2003

By Rennie J. W

In the first five years of longwall mining at Pacific Colliery, special techniques of goaf sealing, gas drainage, goaf edge ventilation and goaf sampling were developed and used to o crcome the concurrent problems of spontaneous combustion and high methane emissions. The English-inspired back-return face ventilation system was modified to suit Australian mining methods and was first used as part of a 'Y' ventilation system and more recently was used with a 'U' system of ventilation. In conjunction with this ventilation system, the maintenance of a sealed goaf area was an essential element in the control of the spontaneous combustion in the goaf.

Jan 1, 1988

By Kaleta S, McTavish LP, Turner RD

Primary production blasting at Hamers- ley Iron began with seven inch holes at Tom Price in 1966 and has developed since then to large multiple row shots of 381 mm holes at Tom Price and 311 mm at Paraburdoo. Up to 1.3 million tonnes are initiated in a single blast with the average around 300,000 tonnes. Development can be traced through Anfo, AlAnfo, slurries, various boosters, initiation and delay techniques, hole loading and daily operating practices. A standard practice could be developed for the two mines for normal pro- duction blasts; this would not apply to such common variations as low "paddy" shots, pre- splitting, tight corners necessitating single row drilling etc. Because of ground variation three or even four sizes of drill holes may well be economic- al for blasting, even though this would be off set by complications in operation, supervision, store stocking and maintenance, particularly in Drilling.

Jan 1, 1978

By E Ben-Dor, D Bakun-Mazor, Y Ben-Ari

Determining the mechanical properties of rocks is important for various civil engineering fields, including the mining of raw materials for aggregates used in the construction and paving industries. Traditionally, the mechanical properties of rocks are obtained through in situ and laboratory tests during geotechnical surveys. However, these time-consuming surveys involve many resources. In contrast, hyperspectral remote sensing methods make it possible to identify the mineralogical composition and crystallographic structure of the rock; properties that control the mechanical properties of the rocks. In this work, we characterise the mechanical properties of carbonate rocks by using a hyperspectral sensor in laboratory conditions. We collected about 150 cylindrical samples of carbonate rock, with a wide range of strength values from several rock outcrops in Israel. We used a point spectrometer in the range of 0.4–2.5 μm and a spectral image sensor in the range of 3.0–12.0 μm, scanning the samples to obtain the signature of their light reflections and spectral emissivity. We then measured the samples’ density, porosity, water absorption, and uniaxial compressive strength (UCS). We used sophisticated data mining to find statistical relationships between the hyperspectral signatures of the samples and their mechanical properties. We used this data to identify the most dominant wavelengths for predicting mechanical properties. We found that the density, porosity, and water absorption of carbonate rocks could be confidently predicted based on spectroscopy data, while the UCS of the rock could also be predicted, but less significantly. The results of the study pave the way for the development of measuring tools for the mechanical properties of rock, based on non-destructive tests of quarrying materials.

Nov 29, 2022

By Frfas C, Parrilla F, Regife J. M

A project to develop the Zinclor electrowinning cell to industrial size is being conducted at Tecnicas Reunidas' Research and Development Centre with Spanish Ministry of Industry support. This project is the final development phase in zinc electrowinning from a chloride medium, the highest ZINCLOR technology development level prior to the industrial scale having already been reached. This paper covers the outcomes and conclusions corresponding to project Phases 1 and 2: Process Selection and Industrial Electrodes (1 m2) design and testing. The most important achievement reached is that there are presently available industrial cathodes and anodes for the Zinclor diaphragm cell giving an optimum response for zinc chloride electrowinning with unit power consumptions between 2.65 and 2.80 kWh/kg Zn, depending on the diaphragm type. Standard electrolysis conditions were: 65 g/L ZnC12, 3 g/L HCl, 160 g/L NaCl, 350 g/t Zn arabig gum as the addition agent, 36¦C, and 400 A/m2 current density. The selection of electrodes, diaphragms and organic additives for the industrial scale tests have been optimised. The complete electrowinning cell development, with electrodes having an active area of I m2, enables the evaluation of Zinclor Technology application for industrial processes.

Jan 1, 1993

Lithocaps are potentially voluminous zones of advanced argillic and associated argillic alteration located above the subvolcanic intrusive environment. They constitute exploration objectives for epithermal and porphyry-type deposits. High-sulphidation epithermal deposits may be sought within lithocaps, whereas low-sulphidation deposits may exist on their edges. Porphyry Cu-Au/Au deposits may be accessible beneath lithocaps if systems are telescoped sufficiently. Oxidation of the basal, pyritic parts of lithocaps may promote supergene sulphide enrichment under appropriate tectonic and climatic conditions.

Jan 1, 1995

By Hashimoto H, Arai Y, Sikong L

For utilization of solid carbonaceous materials produced in processes of cracking heavy oil, such as petroleum pitch, as powder fuel, it is necessary to develop a process for fine grinding of these materials. It is known that grinding' additives are effective for fine grinding of cohesive and heat-sensitive materials such as petroleum pitch, therefore in this study, effective methods for fine grinding of petroleum pitch with some grinding additives were investigated. Experiments were carried out by using comminution kinetics based on mass balance. From the results of the investigation by using a batch ball mill, it was found that sodium stearate, calcium stearate and carbon black were effective additives for the improvement of grinding efficiency. Optimum concentration of the grinding additives was also found to give a required particle size of products. Concerning to the action mechanism of these additives, it is considered that the additives which adhired to, or were absorbed on the surface of petroleum pitch particles not only prevented cohesion of the particles but improved dispersion of the particles as well. From the results of the investigation by using a laboratory screen mill which is a representative built-in classifiered impact crusher, carbon black was found to be an effective additive for the improvement of grinding efficiency and mill performance. It is also considered that the improvement of classification efficiency by carbon black affected the mill performance.

Jan 1, 1987

The iron ore mining operations carried out by Goldsworthy Mining Limited at Golds- worthy, Shay Gap and Sunrise Hill, in the Pilbara region of the North-West of Western Australia, are unusual insofar as the ore reserves occur in a number of widely separated and relatively small deposits, requiring deep mining below the water table, and even below sea level at the Goldsworthy pit. This paper has been prepared to describe some of the problems associated with these deep open cut mines, and the technology employed to overcome them, in order to provide an efficient and economical operation. The problems discussed are: 1. Development of the Dewatering System for the Goldsworthy Mine. 2. The Stability of Pit Slopes at the Goldsworthy and Shay Gap Mines. 3. Development of Diesel Electric Trucks for Lonq Uphill Hauls.

Jan 1, 1979

By E Drueppel, M Mistry, J Pateiro

As mining undoubtedly influences the natural environment future challenges of copper ore mining are minimisation of land use in area and duration, proper land rehabilitation as well as tailings management. One possible solution to avoid these negative impacts could be the application of underground mining with backfilling tailings compounds. This approach would definitely increase the production cost. Against this background the project analyses the influence of an æecologically satisfyingÆ copper ore mining on world market prize and demand as well as on the environment. In the project 261 copper ore mines accounting for 98 per cent of world copper production have been examined. After modelling a backfill plant, analyses of applied backfill techniques were conducted. Afterwards a method of cost estimation was developed and then the backfill plant model was applied in three case studies. The results were transferred into scenarios. The work closes with a short discussion and gives an outlook to forthcoming research. The results presented in this work have been generated within the Collaborative Research Center (CRC) 525 entitled æResource-orientated view of metallic raw material flowsÆ. This interdisciplinary project was established at Aachen University of Technology (Germany) in 1997 and is funded by the Deutsche Forschungsgemeinschaft (DFG). The long-term goal of this research program is the identification of options for the resource-sensitive supply and processing of metallic raw materials. In order to address the sustainable development challenges facing the metals and minerals industry an integrated resource management system is to be developed and tested for important metallic raw materials. Case studies for aluminium and copper are being conducted by the CRC 525 in order to provide useful and efficient tools for decision makers over the entire life cycle of these materials.

Jan 1, 2003

By S Januszewski and, G Dirom, D Christensen

Four field test plots were constructed in 1998 on a sloped waste rock surface at the Myra Falls Operations of Boliden Westmin (Canada) Limited to evaluate hydraulic performance of alternate cover system designs. The field test plot cover systems were designed to control oxygen ingress and water infiltration to the underlying waste rock while providing a medium for a grass and legume vegetation cover. The test plots consisted of a bare waste rock surface (control plot), and three additional plots consisting of native compacted till placed directly on the waste rock surface, overlain by non-compacted till. Two of the test plots included a compacted till layer ameliorated with flyash and bentonite, respectively, to improve moisture retention and reduce permeability. The third test plot consisted of a compacted layer of native till overlain by non-compacted till. A performance monitoring system was installed in each test plot to evaluate net percolation and oxygen ingress to the underlying waste rock. In addition, each test plot has profiles of matric suction, water content, and temperature sensors installed at up-slope and down slope locations. A review of four years of monitoring data shows that the compacted till/bentonite cover system has been most successful in limiting the infiltration of meteoric waters and oxygen ingress to the underlying waste rock material. The compacted till/flyash and compacted till cover systems have produced similar net percolation results and neither have functioned well in maintaining an oxygen ingress layer throughout the year. The amelioration of bentonite with till to produce a compacted barrier layer shows promise in reducing water and oxygen ingress at the MFO site, while the incorporation of flyash with the till did not result in a significant increase in performance. The field performance data clearly demonstrates the need for developing field trials prior to full-scale construction, as opposed to relying solely on an un-calibrated numerical modelling to design the full-scale cover system.

Jan 1, 2003

The underground coal mining industry in Australia has, in the last 30 years, undergone a revolution in production methods, techniques and results probably unparalleled elsewhere in the world. It can lay claim not only to leading the fight against pneumoconiosis and setting high safety standards generally, but has at the same time recorded comparatively high rates of increase in output per man shift. The latter has been achieved as a result of progressively matching the latest in production and underground transportation equipment with significant changes in seam development and extraction techniques and the introduction of stress-relieving extraction methods unique to the world scene. However, the seam recovery factor is still too low. Apart from the overall objectives of maximising production and commercial returns with the greatest safety, there must be a concentration towards maximising seam recovery, particularly in high seams. The search will continue for systems which are more completely continuous mining operations than the present stop-go operations, with longwall having long term potential in this regard, but as yet not sufficiently developed to engender confidence for its more general use. Techniques developed in the last 10 years make the development and extraction of deeper seams, perhaps to 2500 feet or more, feasible with continuous miners as well as longwall. The future will see a greater use of continuous shifts at mines, larger mines with more sophisticated management organisation, extensible belts at the face, better systems of immediate roof support at the face, remote operation of face equipment, greater use of roof bolts and the longer roof cables. With commercial confidence in coal mining now virtually assured to at least the turn of the century, the stage is set for heavy capital development in the industry which will undoubtedly include major research into the whole area of mining methods and equipment. We must ensure that our contribution to such research equitably matches other coal producing countries.

Jan 1, 1975

By Adshead ND, Blake KL, Rotherham JF, Rotherham M, De Jong G

Magnetite deposits with distinctive ¦ actinolite ¦ apatite -bearing gangue and spatially-extensive sodic-calcic wall rock alteration occur in both Proterozoic metamorphic terrains and Mesozoic-Tertiary magmatic arcs. Examples from both settings constitute significant sources of iron ore (e.g. Kiruna, Sweden; El Romeral, Chile) and some host major Cu-Au deposits that have a local association with K-silicate alteration (e.g. Cloncurry district, NW Queensland; Copiapo district, Chile). A growing body of evidence points to a hydrothermal origin for these systems involving high temperature, low S oxidized fluids. The Cloncurry magnetite-Cu-Au deposits are products of the local structurally channelized influx of a specialized high salinity ore fluid into larger-scale alteration systems developed during pluton emplacement at greater depths than those associated with subvolcanic (porphyry) Cu-Au deposits. The geological characteristics of deposits in magmatic arcs are consistent with a similar mode of origin albeit in rather different tectonic settings.

Jan 1, 1995

By P W. Cleary, M D. Sinnott

Cross-belt cutters are commonly used for sampling coal. They are generally cheaper than falling-stream cutters, particularly when a cutter must be retrofitted. The major mechanisms thought most likely to lead to sample bias are being investigated by discrete element modelling (DEM) in a project funded through the Australian Coal Association Research Program. This paper describes a benchmark run and the current direction of research.

Jan 1, 2008

In Australia 'there are hidden deposits of gold, copper, tin, lead and zinc which can be found by drilling at reasonable expense in view of the imp9rtance of the objectives. Exploration of the prospects in mind would mean about a million feet of drilling. The purpose of this paper is to outline, in a technical way, some of the geological thinking that has been given to this matter. To do this, it is necessary to unify the wider ranging thoughts into some sort of coherent perspective and also into some sort of logical sequence. This will be done by treating first the geological subject material which is in fact, at the foundation of the exploratory scheme. With this base, the argument will be continued through a sequence of prospect thinking and brought to a conclusion in regard to the practical employment of geology in the drilling planning. In this knitting together of ideas, the discussion will be given substance by welding into the argument the reasoning that has been applied to the Cobar prospect. The New Occidental Gold-Mines are operating three mines at Cobar, and the writer is indebted to the Company for allowing the reference to be made. It is intended, as opportunity permits, to furnish further examples in later publications.FOUNDATION OF EXPLORATIONThe deposits under consideration are derived from igneous rocks, chiefly granite or porphyry. In and following the emplacement of the intrusives, the rocks have been...

Jan 1, 1946

By Grey D, Turner R, Capsanis J

Coal fines are recognised to have a major impact on the cost and efficiency of the recovery of saleable coal. Fines affect the productivity of the whole mining cycle because of the low yields obtained in washing this material as well as affecting the moisture content and handling characteristics of the final product.In 1990, Coal and Allied Hunter Valley Mine initiated an internal study into coal fines based on the assumption that a reduction in fine coal in ROM material will lead to increase yields in the preparation plant. The initial results of this study indicated that the level of fines in the ROM coal can be reduced by more than 40 per cent by simple changes in blast design and implementation.

Jan 1, 1992

By Lockyer PC, Reed MR Bartlett PM

Difficult ground conditions have plagued the underground operations at Mount Windarra since mining started in 1974.The ore at Mount Windarra consists of seven vertically dipping, sub vertically plunging ore shoots. The ore zone in which the shoots lie is characterised by moderate to heavy cleavage and the presence of serpentanite. The ore is known to extend to 1100 metres below surface.Long hole open stoping under cover of backfill has been used as the primary mining method at the mine, but its poor performance brought the mine near to closure in 1984. The mine had been closed from 1979 to 1980.

Jan 1, 1985