Search Documents

By Georgi H, Farquhar J. W, Lorrigan A. N

The potential for major new lenses of Volcanic Hosted Massive Sulphide (VHMS) beneath the existing Rosebery Deposit is extremely high. Recent deep drill hole intersections of massive sulphides, including 22 in true thickness at 24 per cent Zn, may significantly extend the life of the Rosebery Mine. The Rosebery Ore Deposit is located within Australia's most prospective VHMS mining district, the Mount Read Volcanic (MRV) arc of western Tasmania (Figure 1). The MRVs are a 10 - 15 krn wide arcuate belt of lavas, related intrusives and volcaniclastics. Rosebery is a major Cambrian volcanic hosted Zn-Pb-Cu-Ag-Au rich deposit which has been over-printed by Devonian deformation and granitoid alteration resulting in local rcmobilisation of the ore. The Rosebery Mine Sequence is composed of an east dipping and east facing, predominately felsic sequence of rhyo-dacitic volcaniclastics, epiclastics, sediments and shale lenses more than 500 in thick. This sequence is bounded by two, low angle (35 - 40¦), east dipping thrust faults, the Rosebery Fault to the west and the Mount Black Fault to the cast. The Rosebery Mine lithologies are summarised in the following table: Hangingwall (HW) Polymictic, quartz, feldspar-phyric epiclastics. Black Slates Graphitic, pyritic mudstones. Host Rocks Turbiditic mudstones and sandstones. Footwall (FW) Feldspar-phyric, pumiceous, mass-flow breccias. Cambrian, quartz-feldspar, porphyritic sills intrude this sequence at all levels. Thin, Jurassic, dolerite dykes also occur throughout the mine. Widespread quartz, sericite and chlorite alteration occurs in the FW. This alteration is manifested as quartz-augen schists beneath the orebody. The Host Rocks are pervasively altered with silica, sericite, chlorite and pyrite. Intense carbonate alteration occurs within the orebody, whereas chlorite and pyrite alteration is commonly concentrated directly beneath it. Cambrian volcanogenic alteration is over-printed by three major Devonian, granite-derived, assemblages. These are massive to quartz veined tourmaline, pyrrhotite-pyrite and magnetite-chalcopyrite. Though the Devonian granite has not been intersected in deep drill holes or in mine workings, there is good evidence that it exists within a kilometre of the deposit. The Rosebery orebody is structurally complex when compared to many other VHMS deposits. Evidence for Cambrian growth faulting has been found at the North End of the mine (B lens) where displacement of ore lenses occurs without corresponding displacement of the overlying Black Slates. A well defined cleavage exists throughout the mine, dipping at 28 to 50¦E. East dipping shear zones are also obvious in all parts of the mine workings and reverse movement is evident on many of these.

Jan 1, 1993

By J Johansson

The aim of this paper is to discuss how to form work and organisations in the mines of the future. The Kiruna underground iron ore mine in the far north of Sweden is used as an example on how technical development affects organisational issues like skills, work identity and gender. Over a period of 50 years one can see a transformation of work from manual underground work to automation and remote control from surface level. What characterised the old underground workface was the close relation between man and the hard rock and with arduous physical work under dangerous conditions. Today, the face miners are located on the seventh level of an office building close to the mine. There is also an emerging, and in many aspects already evident, knowledge transformation û from the old and obsolete physical and tacit knowledge and skills (for example the ability to æread the rockÆ) to something new, which can be described as abstract æhigh-techÆ knowledge and skills. The modern technology has created a new type of work û new in terms of competencies and knowledge as well as workload and organisation. At the same time the mining company are recruiting more women and promoting the former pure male work as attractive workplaces for both women and men. All this has effects on how individuals and company create and recreate skills, identity and gender. To some extent the technological development predestines these changes, but there are some choices to be done when forming good work and organisations for the mines of the future. The traditional mining workplace culture and behaviours and the old type of masculinity, the æmachoÆ style, will be challenged by the new æhigh-techÆ work and new competency demands. The changes risk meeting restoring responses, which can have negative impact on the performance of the organisation, for example making it inflexible and perhaps ælaggingÆ behind the technological development. These questions need to be handled when planning future mining.

Jan 1, 2008

By T Kitajima, T Kawaguchi, T Nakamura

Carbothermic reduction of iron oxide is an attractive mechanism to produce metallic iron, since it can directly utilise coal as both reductant and fuel. To improve energy efficiency and productivity of the metallic iron production based on this mechanism, the combustion bed process packed with the composites of iron oxide and coal powder was experimentally evaluated. The process has a potential of high heat efficiency since it can automatically utilise the heat of reduced materials as that necessary to the subsequent reduction of the composite by a large heat exchange rate between the packed particles and gas flowed across the bed. However, it is hard to perfectly prevent the reoxidation of formed metallic iron in the bed. The present paper reports the effect of coal content, pellet size and so forth on the reduction/metallisation degrees of the samples after the reduction experiment. It also discusses the effect of pretreatment of the composite pellets using CaO bearing materials to suppress the reoxidation of formed metallic iron in the bed.

Jan 1, 2000

The title of this paper implies, and the text explicity states, that Sen and Spottiswood (1984) have found a new mineral species related to geocronite and jorganite. I believe that there is inadequate justification for this claim.The X-ray powder diffraction pattern reported by the authors exhibits a close similarity to that of geocronite, as stated by the authors, which suggests a close structural relationship at the very least. It is therefore reasonable to recalculate the results of the microprobe analysis reported by them to atomic proportions on the basis of the geocronite formula. This calculation, whether based on the formula used by Sen and Spottiswood (1984), or on one derived from a crystal-structure analysis (Birnie and Burnham, 1976), namely Pb18 (Sb, AS)11S46, with a total of 86 atoms, gives the results shown in Table 1.

Jan 1, 1985

Instantaneous outbursts have occurred at Metropolitan Colliery from the pick and shovel work of early days to the modern mining techniques of today. Developments have been the introduction of an emission index to measure the proneness of the coal to outbursts, drainage and destressing by large diameter holes, attempts at higher productivity by the introduction of pulsed infusion shotfiring and improvements in ventilation. The future plans and aims for the Colliery include prediction of outbursts, seam gas pre- drainage and longwall mining.

Jan 1, 1980

By J Aitchison, G Clarke

A reappraisal of the stratigraphy, new regional kinematic analysis and thermobarometric data allow a new interpretation of the metamorphic zoning and tectonic structure of the Upper Eocene high-pressure metamorphic core complex of northernNew Caledonia allow a three steps evolution to be proposed: 1. subduction and understacking of previously thinned continental crust elements; 2. subduction blocking due to the crustal thickening; and 3. crustal thinning and extensional detachment during the diapir-like uplift and unroofing of the eclogitic core. Steps 2 and 3 may be partly contemporaneous. Such a model accounts for the thermobarometric and radiochronologic data, and also for the weakness of substratum deformation during the emplacement of the ophiolitic nappe

Jan 1, 1995

The paper is introduced by some general comments on the Electrolytic Zinc Company West Coast Mines operations. An outline of the geology of the Rosebery Mine orebodies preced- es a resume of the mining methods used prior to the current mechanization programme. The reasons for the introduction of longhole stoping techniques are given together with a brief explanation of both sublevel longhole and longhole stoping methods. The application of remotely controlled loaders within these stoping methods is discussed. A description of the remote control mechanisms, used on Atlas Copco 310 and 511 Cavo loaders, is followed by comments on these mechanisms from both a maintenance and production viewpoint. A summary of perform- ance statistics and operator safety records vindicate the selection of remotely controlled loaders for the longhole stoping areas at Rosebery Mine.

Jan 1, 1977

By Smith I. K

A Data Acquisition System with a capacity to monitor 2000 analog instruments has been installed at the mines operated by the Zinc Lorporation, Limited and New broken hill Consolidated Limited (ZC/LVbHC), New South Wales, Australia. Since commissioning in March, 1982, the system has proved its value in providing up-to-date information to both Rock Mechanics and Mining personnel. The paper describes the function of the major software and hardware components of the system, and identifies the advantages that an on-line monitoring system provides in the day-to-day operation of a large underground mine.

Jan 1, 1983

By Richardson F. A

Techniques for flotation optimisation were investigated at Cobar [lines Pty:Ltd., in anticipation of the proposed installation of a computer and on-stream analysis. Successful laboratory and pilot plant tests for flotation performance optimisation using the Simplex Evolutionary Operation Technique (Simplex) lead to a full scale plant test using this method. The index developed for" Simplex response evaluation of flotation performance was based on metallurgical and economic criteria. This index was further modified to minimise the effect of head grade fluctuations. The test program was carried out on one of two parallel copper flotation circuits to allow comparison with normal "manual" operating control, and was conducted for thirty eight shifts. Results from the test section operating under Simplex direction were superior to those obtained using normal "manual" operating techniques and demonstrated the use of the Simplex Evolutionary Operation Technique as a method of reducing reagent consumption in flotation but, at the same time, maintaining satisfactory metallurgical performance. Experience in the use of the technique indicated the need for modifications to the rules of Simplex operations. Modifications were proposed, tested and appeared satisfactory.

Jan 1, 1973

By Weining L

In-situ experiments were performed in a tunnel built in loess soil with the displace- ment components of the tunnel lining and the acceleration components of the tracks measured during the passing of trains. The measured parameters were then studied by the spectral method. As a result, the dynamic forces of trains was simulated numerically and a deter- ministic dynamic nonlinear analysis was carried out by means of finite element method. The results obtained by two different approaches were in fair coincidence. Results of the study indicate, that the low and medium frequency components of the dynamic train loading would be crucial for the dynamic responses of the tunnel lining and surrounding mass, and their effects would increase with the speed of passing trains within a certain range.

Jan 1, 1987

By N Voller, A Ishmurzin, G Hackl, M Wu, A Kharicha, M Chintinne, C M. G Rodrigues, A Ludwig

Slag fuming (SF) is a critical process for recycling zinc-containing slags, but the corrosive nature of molten slag poses challenges to the reactor durability. The freeze-lining (FL) technique offers a solution by forming a protective layer on the reactor wall. It requires intensive cooling using watercooled jackets, which can stabilise the FL while compromising the energy efficiency of the process. This study presents a computational fluid dynamic (CFD)-based model to optimise the SF process by considering FL formation and its impact on heat transfer and reactor wall temperature. A volumeof- fluid (VOF) model is coupled with a mixture continuum (MC) solidification model to capture the intricate multiphase flow dynamics within the SF furnace. Two FL types are considered: FL solidifying on the reactor wall in the slag bath region; and FL solidifying on the reactor wall in the freeboard region. The FL of the first type forms when the slag temperature drops below liquidus temperature. The FL of the second type only forms when a splash-induced slag droplet collides with the freeboard wall and solidifies. A series of splashing events are necessary to coat the freeboard wall. The simulation was run until a global energy balance was reached. This means that the heat losses from the water-cooled jacket, bottom wall, outlet and fuming balance the heat gains from the hot gas injected through the submerged plasma torches. The increase in FL thickness, due to its low thermal conductivity, reduces the heat losses through the reactor walls. The calculated FL thickness and heat fluxes were in good agreement with industrial data, validating the model’s credibility. The simulation results provided valuable insights into the fuming process, including slag bath temperature evolution, slag splashing dynamics, FL formation patterns, local heat fluxes through the reactor wall and overall energy balance. These findings can inform process optimisation strategies to enhance the energy efficiency and sustainability of SF operations. The authors have built a prior version of the model framework and applied it to simulate FL formation in an electric smelting furnace (ESF). The results from both the ESF and the current SF highlight the applicability of such model framework to a range of industrial processes involving FL formation. This model framework can ultimately contribute to more energy-efficient and sustainable industrial operations.

Aug 21, 2024

The sedimentery basins of this region developed in the collision zone of the Pacific Ocean plate and the continent. Stresses were transmitted thorough wedge-like lithospheric blocks, such as the Okotsk Sea, East Kamchatka, Aleutian and 2 other smaller blocks. Compression and inversion were more active at the boundaries: P ; P3 ; N1 ; and Z N in places. ? K2 P2 P3 N2 Tension, rifting and the increase in the rate of sedimentation were marked in '-2 , P3, Ni - N2, and also N2 - Q in places. Structural plan changes of the sedimentary basins and possible oil, gas and fluid migration occurred more actively 2 3 1 2 at the boundaries: ; P3 . N? , N1 N1 NZ N2 P2 P3 1 N1 'N 2 N3 Ni 1 1

Jan 1, 1995

By G K. N Subasinghe

"In the design and operation of mineral processing plants, knowledge of the variability of ore properties and that of the expected metallurgical performance within the orebody is of great importance in order to avoid both production constraints due to inadequate design and less than expected metallurgical performance during operation. Of the many properties that determine the performance of downstream separation processes, such as flotation, gravity separation and leaching etc the liberation characteristics are of primary importance.Current methods of evaluating liberation characteristics of ores such as the use of Mineral Liberation Analyzer (MLA) and QEMSCAN techniques are expensive and suffer from the drawback that these tests are performed on comminuted particles at a given grind size and/or samples of product streams. This problem could be overcome by developing predictive models of liberation that can predict the grade distribution of comminuted products at any grind size based on texture of the parent rock. This paper discusses a procedure that has been developed to predict liberation using information obtained from a sample of the parent rock such as drill core, based on Barbery’s liberation models. The required characteristic statistical functions have been evaluated from image analysis techniques using scanning electron microscope (SEM) images of the parent rock and narrowly sized comminuted particles. Such information can then be used in a predictive model to predict or explain the variability of metallurgical performance at various grind sizes used in future operating plants. The model will predict not only the valuable mineral liberation but also gangue liberation, which will be useful to those who are looking to remove liberated gangue from comminution circuits.CITATION:Subasinghe, G K N, and Dunne, R, 2016. Predictive Model of Mineral Liberation for Geometallurgical Applications, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 347–350 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By Rongqing Q, Tiancong Z, Yiyuan L

The influence of pulp density, ferric ion concentration and particle size on the tank bioleaching of two kinds of refractory gold concentrates are discussed. The chemistry and mechanism of the bioleaching process are also presented. The relationship between oxidation of sulphides, liberation of enclosed gold and gold cyanidation are discussed. The consumption of NaCN could be reduced by alkaline treatment of bioleached residues prior to Cyanidation.

Jan 1, 1992

German coal mining suffers from rock temperatures up to 600C which are the same as in South Africa at 3000 - 4000 m of depth. Therefore cooling plants have increased in the last decade and today a cooling power of nearly 200 MW is installed in the total Ruhr District. Cooling a mine is a little bit different from cooling a bottle of beer in a refrigerator in the kitchen because the heat taken from the bottle of beer is delivered to the kitchen some centimetres away; in mining the cooling-problem is more difficult: here the bottle of beer corresponds to the airflow at the coal face and the kitchen to the surface, So it is necessary to transport the heat or the "coldness" a long distance. In the address by Ieuan Morris some systems for transporting heat from the coalface to the evaporator of the cooling machine and further from the condenser of the machine to a return airflow were described. The following is a short idea of the way this problem is treated in Germany.

Jan 1, 1983

By Whiten WJ

Although cone classifiers have received little attention in the modelling of mineral processing units they are one of the oldest non-mechanical classifiers. Their use has enjoyed a revival in recent years because of their low cost of installation and operation. In this paper the development of models for cone classifiers is reviewed and a new model is proposed. The experimental work, data collection and analysis are briefly described, and the new model is presented and discussed. The data used in the model development are made up from three distinct experiments using different units in each case. There are 21 data sets from a 3 m cone treating the tailings in a copper concentrator, 24 data sets from a 0.3 m pilot-scale cone, and 29 data sets from a laboratory glass funnel (0.(Y73 m diameter) used as a cone classifier, giving a total of 74 data sets. The model structure was developed from an analysis of particle settling in classifiers, using specialised model building software. The size of a particle settling in a separator and the forced flow through the apex of the cone were related via hydrodynamic dimensionless groups to the operating conditions of the unit. The model predicts the separation efficiency using the following four parameters: efficiency curve shape factor, cut-point, underflow density (per cent solids) or underflow pulp velocity. The model covers a range of feed flowrates from 1.2 to 5000 1/min.

Jan 1, 1993

By Richmond GD

The Hellyer concentrator of Aberfoyle Limited commenced production in 1989 processing a fine grained, massive sulphide ore containing Zn, Pb, Ag, Cu and Au as values. Four concentrates are produced - copper/silver, lead, zinc and bulk (Pb/Zn) - with overall payable recoveries (1991) of 80 per cent Zn, 55 per cent Pb, 50 per cent Ag, 30 per cent Cu and ten per cent Au. Metallurgical development work commenced immediately after plant commissioning, and continues. The flotation response and liberation analysis on a size basis highlighted reagent balance problems associated with tower mill regrinding of sphalerite, poor conditioning of flotation pulps, poor selectivity for fine galena, and insufficient liberation. These were the main causes of values lost to tailings, values reporting to the 'wrong' concentrates and of impurities in the concentrates. Modifications to tower mill regrind circuit operation, and the use of improved conditioning techniques have greatly improved concentrator performance, particularly in the finer (-5 micron) size fractions. Studies of concentrator and laboratory flotation by size and liberation analysis are the basis of diagnostic metallurgy. The techniques used to evaluate the improved concentrator performance are discussed.

Jan 1, 1993

Pilot plant work has played a major role in the process development and design phase of the Iscor Heavy Minerals project. The pilot plant campaigns have been aimed at three process areas, namely primary beneficiation (wet gravity circuits), heavy mineral separation and ilmenite smelting. A process development structure was put in place, and the various pilot plants designed and built. A number of pilot campaigns were conducted during the project phase since 1995, and most of the key objectives were achieved. Various other valuable ælessonsÆ were learnt, and were incorporated in the full-scale plant designs, or used to change operating philosophies, equipment choices et cetera. The cost and durations of the pilot runs were significant, and an analysis indicated that the major risk and technology area of smelting has contributed more than 70 per cent of the total cost.

Jan 1, 2001

By Lo YC, Pate WT

In recent years there has been a great deal of interest in ways to optimise the performance of mineral processing plants. This paper describes a methodology developed for optimisation of autogenous and semiautogenous mills. The methodology involves plant sampling, batch testing, modelling, computer simulation, control strategy evaluation and implementation. The models have been tested in plant operations to verify the research findings and predictions. Two example applications of this approach to plant optimisation are presented. Benefits reported in these two examples are in the range of four - eight per cent increase in size reduction efficiency.

Jan 1, 1993

By H M. A Ilyas, M Yahyaei, S Amari, M Darestani

Tailings are generally deposited on or near to the mine sites, occupying the site area, and being an economic burden for mining companies. Tailings can cause several environmental impacts, such as leaking toxic substances and contaminating underground water, emitting greenhouse gases, and damaging natural bodies and wildlife. Geopolymerisation of mine waste effectively transforms mine waste into more valuable, environmentally friendly products. Geopolymers are inorganic aluminosilicate materials that are widely applied in the construction industry (Araya, Kraslawski and Cisternas, 2020). The high performance and the low-CO2 emission of geopolymers make this type of material potentially more desirable than ordinary cement, given that manufacturing one ton of traditional cement generates approximately 0.8 tons of CO2. This process is seen as a promising method for repurposing tailings and reducing the environmental impact of mining waste. However, the environmental impact of geopolymer production is not sufficiently comprehended (Mazzinghy et al, 2022). Moreover, geopolymerisation of mine waste can offer several economic benefits, including reduced waste management costs (Amari et al, 2019; He et al, 2022), reduced raw material costs, and potentially lower production costs. However, there are several challenges that need to be addressed to ensure the economic feasibility of the process. This study aims to demonstrate the potential environmental impacts of geopolymer concrete produced using mine wastes and industrial by-products such as blast furnace slag (BFS). For this, a comparative cradle-to-gate life cycle assessment (LCA) methodology was conducted on different geopolymer mix designs, and the greenhouse gas (GHG) emissions results were compared to the ordinary cement. LCA can be used to evaluate the environmental impact of geopolymerisation of mine wastes in various ways. One important impact category is GHG gas emissions, which contribute to climate change and is the focus of this study. Another aim of this study is to evaluate the economic feasibility of the geopolymerisation of mine wastes via economic analysis (EA) to identify the key economic factors and trade-offs associated with repurposing mine wastes through geopolymerisation.

Aug 2, 2023