Search Documents

By D Ziaja, W Jaspers

A brief history of the development of pneumatic flotation cells from early in the 20th century to the present day and a comparison to conventional cells demonstrates the efficiency and simplicity of design and operation of the ænew generationÆ of pneumatic cells. Recent successful testwork on phosphate minerals in the USA and a variety of coal types in Australia confirm the utility and efficiency of the design. The key aspects of this technology are improved recovery and selectivity with lower capital expenditure and operating costs.

Jan 1, 2005

By Blair JR

The tunnel alignments investigated for the Gosford Regional Sewerage Scheme are located in the Terrigal Formation and are covered for most of their length by a thick blanket of soil and weathered rock. The following techniques were found to be most effective in geotechnical investigations for tunnelling in this area: air-photo interpretation, seismic surveys to pinpoint drilling targets, in-situ measurements of strength,deformation modulus and permeability in cored holes, and the construction of rock- mass models. Cross-hole seismic modulus measurements, surface resistivity soundings and electric well-logging techniques were found to have limited applicability due to adverse local conditions.

Jan 1, 1976

By Baafi E. Y

Dragline monitoring systems are normally the best tool used to collect data on the machine performance and operational parameters of a dragline operation. This paper discusses results of a time study using data from a dragline monitoring syste

Jan 1, 1998

In coal room and pillar, and pillar extraction panels, the sidewall conditions were investigated based on underground measurements and numerical simulations. Three-dimensional linear elastic models provided a useful and quick prediction of the amount of sidewall spalling. However, more complex constitutive models were required to simulate more accurately the extent of fracturing and its effect on the stress re-distribution. The input parameters of a Mohr-Coulomb model were determined by back-analysis of underground measurements, and the effect of the depth of the workings and the time dependent occcurrence of coal pillar fracturing were analyzed.

Jan 1, 1992

By Crockford GI

Some twelve months of operation at Mount Lyell, using two large diameter ball mills as a two-stage grinding circuit indicated a short- fall in the grinding capability compared with design criteria. Breakage, particularly at coarser sizes, was less efficient than with the previously used grinding circuit comprising a large number of smaller diameter mills. This paper describes both old and new equipment, puts forward the facts as they are presently known, and lists the attempts made to overcome the problem.

Jan 1, 1978

By Wilson PH

A research programme sponsored through the Australian Mineral Industries Research Association investigated two aspects of mine aerodynamics on model scale. These were aero- dynamic losses in (a) shaft/airway intersections and (b) losses created by mine cages moving in a combined haulage/ventilation shaft. The shaft/airway intersections studied included base and intermediate levels for both upcast and downcast. shafts, with one to four rectangular airways intersecting a circular shaft. Changes in intersection geometry were limited to the installation of 45¦ conical brow cutoffs of varying size and the addition of simple flow control devices. The relative air- flows between the airways and the downstream shaft were varied over a range employed in Australian mining practice. In general, experiments revealed that a small brow cutoff was significantly better than none at all, and a simple device such as a cone can reduce losses and improve flow stability at an intersection. The mine cage studies determined the effect on aerodynamic loss of cage area blockage, height/length ratio, openings in cage walls and surface roughness due to external structural members. The results show that in a combined haul- age/ventilation shaft, when the relative air

Jan 1, 1978

The Olympic Dam smelter utilises Outokumpu Oy, flash smelting technology to produce blister copper direct from high grade copper concentrate.This paper describes the unit processes involved, including filtering/drying, materials handling, smelting, gas/dust handling, waste heat recovery, sulphur fixing, anode refining and casting.

Jan 1, 1993

The South Wall Base Case Design for Mt Whaleback indicated that along portion of the South Wall a cigar shaped synclinal keel, contain- ing 14 800 m', of Dales Gorge Member ore, would be unkeyed and bed- ding undercut. The dry "ore lobe" slope would be 60m high, unbenched and approximately 170 m long. Stability analyses using specific design parameters established that artificial reinforcement could stabilise the slope and be economically justifiable. To implement the slope design reinforcement for such a complex geo- logical structure it was necessary that all functions pertaining to slope excavation be integrated and co-ordinated within the Mine Geotechnical Section. The objective being to minimise slope damage and thereby optimise the effect of design reinforcement. The successful excavation of the ore lobe in 1988, three years after the introduction of artificial reinforcement, was achieved by strictly main- taining the following parameters. 1. Accurate Geological Model 2. Controlled Perimeter Blasting 3. Controlled Excavation Techniques 4. Quality control -Reinforcement Installation 5. Additional Reinforcement.

Jan 1, 1989

Different mineral structures can act as mineral reservoirs for the immobilisation of toxic compounds. In the paper different mineral structures will be explained and their potential for incorporation of heavy metals and anions will be shown. The following structures will be explained (P÷llmann, 2007):apatites (incorporation of heavy metals, silicate apatites);ettringites (fixation of oxo-anions);layered double hydroxides (fixation of heavy metals, fixation of anions, fixation of organics, sorption materials); andmanganese oxides. Different possibilities of solid solution and incorporation in crystal structures will be explained and advantages of stable minerals be proved using experiences with real toxic wastes. In the process of thermal treatment the formation of primary mineral reservoirs will be shown. The precursor phases (similar to well known cement minerals) react in contact with water to form secondary mineral reservoirs (cement hydration mineral products). The formation condition of primary and secondary mineral reservoirs and their stabilities and incorporation possibilities will be shown. Examples for incorporation of various elements are given. Application for water clarification will be outlined.

Jan 1, 2008

The major coalfields of Australia are almost unique in the occurrence in some areas of CO partly or almost completely replacing CH4,t1e normal seam gas from metamorphism of coal due to time and depth of burial. This CO2 situation has some benefits but mostly it introduces particular safety problems result- ing from the high density of CO2 relative to air, magnifying problems of gas dilution in ventilation, and the greater affinity which coal has for CO2 than for CH4 increasing proneness to gas-dynamic phenomena. The occurrence of most CO2 seam gas can be directly related to igneous intrusion and to its associated pneumatolytic injections. Whilst intrusions locally increase the rank of coal by their contact metamorphic effect, normal coal metamorphism due to time and depth of burial continues after intrusion and injection together with the ongoing metamorph- ic production of CH . This new CH slowly displaces any CO to leave some present-day intruded coals with seam gas with reduced CO2 or even without any significant CO2 associat- ions. The seam gas maps of the Bowen and Sydney Basins and more detailed maps of specific areas exemplify these situations. Mining progress, plus more searching studies of igneous-coal relationships provide improved understanding of the factors involved.

Jan 1, 1986

By Scherbatsky VB, zon BM, Babushkin NM, Kitaev BI, Shabel&apos

The structure and hydrodynamics of the raceway zone of a blast furnace was studied on a cold model representing a sector containing two tuyeres. The model differed from the usual in that it was prov- ided with continuous flow of the coke layer at pre- determined rates, had provision for changing the tuyere parameters (diameter, protrusion, inclinat- ion) and irrigation of the layer with liquid. A combination probe was developed which per- mitted simultaneous measurement of the pressure field both across the area and through the height of the layer as well as determining the topography of the raceway. The velocity fields in the layer were measured with a specially made impulse thermo- anemometer. The determining criteria of the model were taken as the relationships between the energy of the blast and the particles, the dimensions of the raceway and the cross-section of the tuyere. The model established the effects of the tuy- ere structural parameters, blast parameters and amount of liquid products of smelting on the con- figuration of the raceway, the structure of the layer, pressure and velocity fields in the vicinity of the tuyeres and in the vertical direction through the layer. The properties of the raceway formation and the structure of the layer in motion have been clarified.

Jan 1, 1981

By Quemard D, Troncoso J

The Gordonstone Project with a capital cost in excess of $500 million will become the largest underground coal mine in Australia. The project development decision was taken on 31 July, 1990 and at 31 May, 1991 construction was approximately 35 per cent complete. The first train of processed product coal will be railed to Gladstone during December 1992. The general theme of this paper therefore will address the planning and development processes at Gordonstone particularly the interrelatedness of technical, production, construction and environmental disciplines to ensure success during operations.

Jan 1, 1991

By Amelunxen R, Finch JA

Flotation columns represent an important addition to flotation practice. Columns have largely replaced. conventional machines in molybdenum cleaning in Canada. Columns have been successfully tested on bulk copper/molybdenum cleaning at Gibraltar Mines Ltd. A rougher cleaner/scavenger cleanercombination was shown to be capable of giving higher grades and recoveries compared with three stages of conventional cleaning. A control strategy for the columns has been developed. An interaction between gas hgldup and wash water rate has been exploited to control performance.

Jan 1, 1985

By Hall T. P, Taylor R. N

Fluid flow in a 1:14 scale water model of the shaft and settler of the Kalgoorlie Nickel flash smelter has been investigated by flow visualisation and numerical modelling. Detailed flow fields through the reaction shaft, settling chamber and uptake are presented for flow rates up to 800 Vm and a number of burner configurations. The predicted flow fields were compared with experimental data obtained from streak photographs and video recordings. The effects of cessation of flow through individual burners and changes in shaft dimensions were also Investigated.

Jan 1, 1992

By Nemcik JA, Gale W. J

The magnitude and orientation of the in situ stressfield has been determined as a key factor in controlling the stability of openings for both coal mine development and extraction. Monitoring of roadway and pillar behaviour in conjunction with numerical analysis has identified specific stress control measures that have been successfully applied to improve productivity in underground coal mining operations. The influence of the major horizontal stressfield on the stability of openings has been identified at a wide range of sites including mines in Australia, Britain, the USA, New Zealand and Japan. Stress mapping, stress measurement and stress monitoring techniques have been applied to define the in situ stress regime and, together with the correlation of measurements of rock deformation and rock reinforcement behaviour, has enabled appropriate stress control measures to be developed. Stress control measures for development headings have required the selection of roadway orientation, roadway sequencing, reinforcement density and pillar size. The monitoring of behaviour at a range of trial sites has confirmed significant improvements in development stability. Stress control measures for longwall extraction have required rational selection of longwall orientation and extraction direction. Where a mine layout design incorporating the optimum longwall layout design has not been possible, the use of sacrificial roadways has been successfully applied to protect key roadways from stress concentration effects. Comprehensive in situ

Jan 1, 1992

This paper introduces a classification of gold orebodies, and comments on the importance of cutting high grade values, the choice of an appropriate ore reserve method and the necessity for producing recoverable ore reserves by considering the mining policy. The author stresses the importance of obtaining the appropriate information from the data relevant to a particular deposit as opposed to transfering parameters from one deposit to another.

Jan 1, 1987

By Mckenzie CK, Scott A

The injection of coal as an auxiliary fuel in ironmaking blast furnaces has been introduced on many furnaces worldwide. This paper examines the present practice of coal injection and discusses future directions for the technology. This has been undertaken through the use of a heat and mass balance model which predicts the replacement rates of coke by coal and the effect of coal injection on blast furnace productivity. The results indicate that future pulverised coal injection could replace substantial quantities of metallurgical coke, but that the energy balance economics of individual steel plants will have a dominating influence on the future of the technology.

Jan 1, 1987

The problems arising in the excavation of hard rocks with the use of mechanical tools consist chiefly in a slow advance rate accompanied by an intensive wear due to the toughness and abrasiveness of the rock. In order to allow the further extension of mechanical excavation beyond the limits of the presently available technology, the assistance of waterjet aiming at improving the performance of the equipment while reducing the wear rate of the tools, has been recognised as one of the most interesting technical solutions. The paper illustrates the improvement of the performance of both disk cutters and picks obtained with the waterjet assistance at the Waterjet Laboratory of the University of Cagliari on a medium-hard rock.

Dec 6, 2010

Based on twenty years of experiences of applying computers in mine water engineering in Hungary, a program package was developed for home utilization and for other users abroad as well. This program package has been adapted to the CAD System of Coal Mining of COMECON countries. The main features of the "mine water subsystem" in the CAD System of Coal Mining and short descriptions of the key programs of the package are presented in this paper. Foreword The serious water problems of Hungarian mining pressed and/or stimulated its professionals to apply computers for supporting their problem-solutions. The first trials of these computer applications in mine water engineering were dated from the sixties. Owing to its twenty years of experiences in computer appli- cations in mine water engineering the Central Institute for the Development of Mining in Hungary was requested to work out the "Subsystem of Mine Water" for the Computer Aided Design System ('CAD) of Coal Mines in COMECON countries. This paper gives a brief presentation on the main features of this "subsystem"with reference to significant components.

Jan 1, 1988

The patterns of flow of reaction gases through the flash furnace at the Kalgoorlie Nickel Smelter were simulated in a 1:20 scale model using a flow of water. Particular features of the flow down the reaction shaft, through the settling chamber and into the uptake leading to the waste-heat boiler were examined. Inferences were made concerning the effects of the patterns of flow on the efficiency of the smelting reaction, on the entrainment of dust by the gas stream and on the erosion of the refractory lining of the furnace. In addition, the effects of geometrical modifications to the arrangement of the concentrate burners and to the profile of the settling chamber were explored by making these changes to the model and observing the resulting variations in the patterns of flow.

Jan 1, 1991