Search Documents

The ore body being worked is about one hundred feet in length by seventy feet in width. A face of about fifteen feet is stoped over the whole level at one operation, this height standing without any timber.Double lines of logs, twenty feet in length and from ten inches to one foot in thickness at the small end, are then laid longitudinally, butt to butt, and breaking joint from end to end of the ore body they are at ten feet centres from wall to wall. The starting logs are single for the first ten feet and their ends are hitched into the solid rock. These are called "miners" and are the logs which are picked up as the level underneath is worked up. The double layer gives a better chance of picking up. Logs are now laid from the centre of the ore body at right angles to the miners, the ends being hitched into the walls. A space, seven feet wide, is left open right through the centre of the ore body...

Jan 1, 1904

By Y Zhang

Being analysed systematically, the factors influencing the production of fully-mechanised coal face have been divided into geological, mining technical, and management groups. Artificial neural network-expert systems (ANN-ES) are established to decide the influencing factorsÆ membership grade; genetic algorithm-artificial neural network (GA-ANN) are used to decide the weights; fuzzy comprehensive evaluation method is used to calculate the integration indexes. Finally, the GA-ANN model is established to forecast the production of fullymechanised coal face. It is proved that the model is reliable with higher precision. The production of fully-mechanised coal face is influenced by many factors. However, some influencing factors are neglected by the traditional forecasting methods, the results of which are not precise and hardly be used as a guide for mine production and management. The relation between the production of fully-mechanised coal face and its effecting factors is analysed, and the meta-synthetic AI approaches are used to forecast the production of fully-mechanised coal face.

Jan 1, 2003

By M Noppe, I Glacken

There are many critical nodes along the mine value chain, from orebody to mineral product, and inter-disciplinary input is required to analyse the variability and uncertainty at each node in order to identify and mitigate areas of risk. Mining differs from many other industries in that the variability in the product is dictated largely by the inherent nature of the input material (the orebody). The true characteristics, including the variability of the orebody, are never known exactly and are instead based on estimates derived from sample data. A further difference is that bottom-line gains are largely controlled by world commodity prices, which can vary with time, rather than by local supply and demand issues. Methods for identifying, reporting and responding to this inherently variable raw material are discussed. These include analytical and reporting methods, equipment and software, risk analysis and reality checks (eg reconciliation). Sampling results, mineral resource and ore reserve estimates and economic assumptions are a function of the variability of the orebody. Risk quantification should be expressed as a level of confidence, which takes into account the scale or period over which the risk is being assessed (life-of-mine, annual or shorter production periods) and should convey the likelihood, severity and consequence of occurrence of a given event. The future generation of mining specialists needs to understand the entire mine value chain to better manage risks and maximise mine dollar-value.

Jan 1, 2002

By W F. Bawden, J T. Paynter

This investigation involves laboratory testing and stability analysis of paste fill at the Golden Giant Mine. Site-cast samples are tested in unconfined, confined, and consolidated-undrained triaxial compression. Pore pressures during shear and consolidation characteristics are measured to determine both drained and undrained shear strength parameters and assess the potential for undrained loading. Liquefaction potential is also considered. A limit equilibrium solution is used to obtain factors of safety against failure of the fill during mining of adjacent stopes.

Jan 1, 1998

Samples weighing O·25 g are fused with 1 g potassium hydrogen sulphate, leached with 5 ml. of hydrochloric acid, and then diluted with another 5 ml. of acid. After settling, an aliquot of the clear solution is reduced with stannous chloride, and then a zinc dithiol solution is added to form a coloured tungsten complex which is extracted with petroleum spirit for comparison with standards.Concentrations down to 4 p.p.m. may be analysed at a rate of 100 determinations per man-day of 8 hr.

Jan 1, 1970

By Potter OE

There appears to have been a swing away from the study of mathematics, the physical sciences, foreign languages and the classical humanities subjects by many students in high schools in Victoria. The same trend is believed to be occurring in other states as well. This has the direct result of many students entering tertiary studies inadequately prepared academically. This is particularly true in engineering and commerce. The position as far as postgraduate training in the areas of concern to the minerals industry is critical with almost no Australian nationals undertaking advanced technological studies.

Jan 1, 1981

Twenty years of effort in developing the use of computers in the design and control of mineral treatment circuits has resulted in a sound base for future widespread application of the techniques.. The intent of this paper is to speculate to some extent about future applications of computer related techniques in the mineral extraction industries. The use of simulation methods for the analysis and design of circuits is discussed. In the area of process control, computers have been largely devoted to process monitoring and reporting tasks. The application of computers for the total control and optimization of complete plants is considered. Finally, the role of computer based modelling studies for definitions of optimum treatment flowsheets is suggested.

Jan 1, 1985

By Boyce WH

Earthquakes are the most frightening and devastating natural phenomena known to mankind. They strike without warning and their consequences can be disastrous in terms of the toll of human life, financial crises related to the damage or destruction of man-made structures and the social and economic effects on a wide spectrum of the affected communities in the aftermath of the event. Such situations can be widely attested to by most areas around the Pacific Rim. Indeed, the threat of earthquakes is always imminent because of the geological-tectonic nature of the region as manifested by past experiences. It is patently obvious that earthquake occurrences are not only a geological hazard but also pose a serious social danger. When one considers the 19 September 1985 Mexico (Michoacan) earthquake (Mitchell at al., 1986), the necessity of continuing research is of paramount importance. An estimation . of earthquake risk encompasses both qualitative and quantitative aspects and demands a multidisciplinary research effort integrating seismology, tectonics, geology, enginering, sociology, economics, insurance and governmental policies (Bolt, 1978; Booth, 1984). These roles in mitigating such a hazard have been aptly discussed by Press (1985). A series of discussion papers based on an intergovernmental conference covering the whole scenario were published by UNESCO (1978). A comprehensive case history was provided through a workshop on the 1886

Jan 1, 1987

Education and Training for the minerals industry has been identified as one of the key priorities by the AusIMM and many closely related groups. The AusIMM Education Taskforce has been engaged, through a visioning exercise, in evaluating what minerals education and training should look like by 2025. A common recurring theme is that for minerals education and training to be efficient and effective into the future, it needs to be comprehensive and inclusive. Some previous attempts to achieve efficiency and effectiveness have had limited success, mainly due to approaching the issues involved from a narrow, singular perspective. This paper outlines that the achievement of the desired outcome may require an approach that parallels the same techniques that are used for multi-dimensional mine planning, treating tertiary minerals education and training in a similar way to the planning involved for a complex orebody. Just as efficient and effective mine planning requires engagement and understanding of many factors, so too does engagement with tertiary minerals education and training. The major factors that need to be considered are outlined in the paper, including: levels of tertiary education and training; Australian Qualifications Framework (AQF), Levels 1 to 13: systems of minerals education and training, such as higher education, (mainly universities), industry/professional associations and licencing requirements, vocational education, (mainly TAFE) and workplace programs; types of minerals or mining methods involved; volume of delivery; stage in the flow sheet, (geology, mining, beneficiation, extraction, refining). For comprehensive mine planning there is the need to develop links or roadways and openings between different levels of a mine. Similarly, to achieve a comprehensive tertiary minerals education and training model, there is a need to develop pathways, recognition and credit transfer between the various levels and components of minerals tertiary education and training.

Jan 1, 2005

By Sturgul J. R

A major electricity generating authority have a proposal to construct a Power Station. An understanding of the operation of the bunker system is of importance to the designers and a computer simulation model of the operation was constructed. The computer language used was GPSS/PC which is a recent form of the language designed for the per- sonal computer. The model simulated trains arriving at the power sta- tion and unloading onto conveyors which carry coal to the power station bunker. Coal was drawn from the bunker at a specified feed rate to the power station. Numerous restrictions were placed on the model, if the bunker level got too high dozers would pull coal out of the bunker onto the stockpile, and if the level got too low the dozers would push coal back into the bunker. The conveyors and dozers were unavailable due to breakdown'at various times and trains would arrive randomly about a mean interarrival time. The system was simulated for 30 years of oper- ation and the model used a basic time unit of 30 minutes so that the system was updated 525,600 times during the simulation. The results of the simu- lation gave the designers a greater understanding of the critical factors in the operation, which may now be engineered to minimise adverse Effects.

Jan 1, 1988

By Corner NG

A sea bed sampling programme by CRA Exploration Pty. Limited over an area of 12000 km offshore from Westland, Southland and Otago, New Zealand, led to the discovery of the Harvester Prospect, an area of some 67 km2 which averaged 189 mg/m3 gold in surface samples. This area was in water depths of 70 to 100 m and contained a high grade core of 33 km2 which averaged 283 mghn3 gold. The gold recovered was fine grained, averaging 124 microns, and indicated a potential resource of approximately 10 t of gold per metre of thickness. Interpretation of existing seismic and geological data suggested that the gold anomaly may be associated with a unit of sediments 10-40 m thick, probably deposited during a lower sea level stand. Two initial attempts at vibrocoring the anomaly produced inconclusive results. In 1989 a much more powerful vibrocorer with scaled up support facilities and a dedicated 24 It turnaround laboratory were employed. The final results clearly showed that the gold was from an uneconomic surface enrichment.

Jan 1, 1990

Previous methods for the assessment of the explosive potential of gas mixtures have required the plotting of apeexplosibility diagram. These became cumbersome if a large -number of assessments of various sampling locations over a period of time wererequired. This may make the approach of a dangerous situation more difficult to predict. With the aid of a programmable calculator, a new method for the rapid assessment of the explosibility of coal mine sample gases has been developed. This method does not require that an explosibility diagram be drawn to indicate the explosive status of a gas mixture. Simple Cartesian co-ordinates representing the explosive potential of,mixtures are obtained, which may readily be plotted to show changes with time.

Jan 1, 1981

The large, high grade 3000 and 3500 copper orebodies at Mount Isa lie greater than 1200 m below the surface, and partly beneath the silver-lead-zinc mining operations at the Isa Mine.Since discovery over 30 years ago, the primary data acquisition programs have been integrated with long-term copper production strategies. These potentially sizeable and distinctly separate accumulations of copper mineralisation are the only sources capable of supplementing a decline in output from the 1100 orebody in the 1990s. Within a decade these deeper copper orebodies will become the major source of copper ore.

Jan 1, 1993

By Matsuo T, Uga Y

The tunnelling work to construct a sewage trunk line designed by the Sewage Bureau of Kobe City along north side slope of Rokko mountain range incorporated an all ground condition type (broad spectrum) TBM with slurry transport system with jet pump manufactured by Kawasaki Heavy Industries, Ltd. Boring dia. of the tunnel measured to 2.0 m. The construction planning and implemen- tation were done by Ohbayashi Corporation, the general contractor. The heading way was 3342.4 m in overall length.; construction work ran from April '84 to June '85. The max. daily progress marked 31.9 m and the max. monthly progress 493.1 m according to the relevant record. The machine proceeded with the work under geological conditions featured with conglomerate, rhyolite, tuff breccia and slate, whereby soft soil zone mostly of clay was encountered in a limited area. In the latter case, however, steel segments were substituted for supporting steel ribs. The tunnel was routed beneath a meandering road with the result that more than 40% of overall length show a curvature of 50 to 200 m radius.

Jan 1, 1987

By Zervoudis J

Limitations of current touch-up solders for galvanised steel include coating thickness control problems and poor corrosion and abrasion resistance as well as health and environmental concerns due to toxic constituents such as lead. This paper reports on progress in ILZRO-sponsored research to develop an improved touch-up solder. Encouraging results were achieved in torch soldering trials with experimental zinc-tin-based alloys. Mouldability and coating thickness control were achieved over a practical working temperature range in which the solders consisted of a viscous mixture of solid primary zinc phase particles in a liquid zinc-tin eutectic matrix. The mouldability was dependent on the microstructure of the solder sticks, and optimum structures could be obtained through control of casting solidification rates and by the addition of small amounts of copper. Hardness, abrasion resistance, adhesion and corrosion tests on experimental Zn- (40 - 50 per cent) Sn-I per cent Cu also showed improved performance over lead-tin-zinc solders and compared the effects of tin content within this range. Atmospheric corrosion testing and optimisation of alloy composition and methods of solder stick production are continuing.

Jan 1, 1993

Stawell Gold Mines Pty Ltd operates two underground decline mines within the township of Stawell. An active exploration program and commitment by owners to improving the ore reserves has led to an improved mine life and reduced operating costs since the purchase of the operation by Mining Project Investors and Pittston Mineral Ventures in late-1992. Over the past six years of operation a cumulative 1 150 000 ounces of gold have been added to the mineral inventory. An improved geological understanding of the orebody has evolved over time increasing the ore reserves and allowing the development of long-term plans for the mines future. This has enabled important capital decisions to be made providing the impetus for improved productivity and thereby reduced operating costs. Co-operative mine planning and mine geology utilising best practice geological systems have enabled the effective extraction of a structurally complex and mineralogically varied deposit within a rural Victorian township. Detailed metallurgical research has improved the function of an aged and poorly designed circuit to boost the mill capacity whilst also improving the metallurgical recovery. The combination of metallurgical expertise and an understanding of the geological setting enable an effective control of metallurgical recovery.

Jan 1, 2000

By D M. Aranha, A R. Cabral

Theories on the origin of the Itabira iron formation (itabirite) in Quadrilßtero Ferrffero (QF), as elsewhere in the world, are restricted by the apparent lack of adjoining volcanic units, severe syndeformational metamorphism and deep weathering. Besides the three types of iron formations at QF (siliceous, dolomitic and amphibolitic; Dorr, 1969) we include a fourth type initially described as ocherous, goethitic, limonitic or even yellow iron formation. Considering its high magnetite content, it has been described as yellow magnetite itabirite (Pires, 1979). It was reported as formed by the alteration of the dolomitic itabirite (Dorr, 1969) although the anomalous Al2O3 contents are high for normal weathered itabirite. The yellowish magnetitic itabirite occurs at the bottom of the Itabira Iron formation, along the contact with the Batatal schists, and at the top units of the Itabira, within the Gandarela Formation. Within the magnetitic itabirite at the Tamanduß iron ore mine there are metric zones, concordant to the bedding of pillow-like structures, exhibiting a porous core, surrounded by an intermediate, more granular zone with numerous, minute rounded cavities grading to an external, fine-grained zone with much less minute cavities. In the external portions of some pillows a breadcrust type structure, derived by quenching with the water can be observed. In some other zones, such as the Barreiro hill, an outer, vesicular, whitish yellow, 5 - 10 mm thick, band grades to an aphanitic, isotropic band. The vesicles are slightly flattened against the band surfaces. The existence of fragmental layers showing flowage and fragment alignment, kaolinitic laminas and vesicles filled with kaolinite at Barreiro Hill and Capitpo do Mato Mine represent mesoscopic structures, indicators of a possible volcanic origin. Chemical compositions of the magnetitic itabirite from a wide area in QF revealed a relatively high Al2O3 content, consistent with a volcanic origin.

Jan 1, 2005

By Buizen M

An investigation into the mechanics of sub-surface deformation caused by caving of the extracted area behind retreating longwall faces has been completed by the Subsidence Engineering Section of the New South Wales (NSW) Department of Minerals and Energy. Changes in strata bulk permeability were also measured by standard packer tests undertaken before and after mining. The strata movement was measured by a multi-wire borehole instrumentation system consisting of mechanical anchors installed at different horizons in a borehole extending from the surface to the coal seam. The mechanical anchors were collected to suspended weights on the surface by stainless steel multi-strand wires. The movement of these weights was monitored as the longwall face approached and retreated past the borehole. The anchors did not move significantly until the face went past the borehole. For subcritical extraction geometry with the extraction width to mining depth ratio of 124, the caving zone extended to roughly 9 times the extracted seam thickness above the seam roof. Tensile strains within the overburden tended to be much more closely related to stratigraphy than to the proximity to the extracted seam roof. Larger tensile strains were associated with layers of sandstone, siltstone and conglomerate, whereas layers of mudstones, claystones and coal underwent much smaller strains indicating subsidence in blocks. A beller correlation was observed between pre-mining Rock Quality Designation and permeability than between rock type and permeability. This correlation was less evident in the post-mining core logs. There was an overall increase in bulk permeability after mining.

Jan 1, 1990

A number of small copper deposits occur in the Pernatty Lagoon-Mt. Gunson area. Textural and mineralogical differences distinguished the lagoon sulphide deposits, which occur in a water filled basin of permeable bedrock immediately under the lagoon floor, from the largely oxidized deposits which occur in the low hills adjacent to the lagoon deposits.Groundwaters are carrying copper, and to a lesser extent zinc, downstream to the lagoon. Several species of sulphate-reducing bacteria are widespread in the groundwaters and lagoon muds.It is suggested that copper sulphides were first deposited at the same time as, or soon after, the host Proterozoic sediments, and that during the present cycle of erosion the lagoon deposits may have been enriched, or largely formed, by bacterial precipitation of copper sulphides from laterally migrating cupriferous groundwaters.

Jan 1, 1971

By Zhao JC, Chen JJJ

A water/air model was developed to simulate the refining of molten aluminium by the sparging of gas through an impeller. The optimal gas dispersion depends upon selecting the correct gas rate for a given impeller rotational velocity to prevent flooding or channelling. Correlations illustrating this flooding behaviour exist for standard impellers within standard tank geometries. However the validity of these correlations has not been substantiated for gas dispersion in high temperature molten metals with non-standard tank and impeller dimensions.

Jan 1, 1995