Search Documents

Historical exploration of the Ballarat East goldfield defined two primary quartz vein lode types. Tracking the intersection of these lodes with vertical lines of enrichment (or so-called æindicatorsÆ) was the basic practice for historical mining. This strategy proved highly successful in terms of identifying quartz veins associated with mineralisation. However, it provides little understanding of the timing or processes involved in the formation of these veins, or the associated emplacement of gold. Current underground mapping shows the Ballarat East gold deposit can be subdivided into four stages of vein formation. The earliest veins (V1 and V2) strike north-south and formed during bedding flexural slip and limb thrust fault propagation in parasitic chevron folds. V3 veins are subhorizontal and relate to further fold tightening involving a transition from east-west compression to north-south extension that initiated re-shear of bedded slip surfaces and additional strike-slip faults. Sporadic V4 veins overprint the shallow-dipping sections of V2 and V3 veins and are associated with weak north-south compression. The V4 veins mineralogy is distinguished by a high carbonate content and sphalerite-galena sulfide assemblage. Vein sampling indicates a significant increase in gold mineralisation where overprinting by the later deformation/veining has occurred. As a result of these observations, a new model is emerging that identifies the chronology, structural control and spatial distribution of respective quartz vein types. This is a major advance in terms of exploration targeting, resource modelling and mine planning.

Jan 1, 2008

Before commencing design of a coal prepar ation plant, it is essential to have detailed information of the raw coal to be treated to- gether with a clear understanding of the products required. Prediction of raw coal size distribution, particularly the amount of fine material, is difficult and the methods employed should be large scale pilot plant studies or techniques to simulate coal degradation and shale breakdown in water. A detailed knowledge of well proven coal preparation processes and new developments allows processes and process combinations to be compared to'obtain the maximum economic recovery when using lower cost, less efficient processes within acceptable limits. Equipment should be selected bearing in mind its precise application and the location where it is installed. Plant layout should be carefully studied to minimise equipment requirements and to simplify construction. Measurement, control and automation should be an integral part of plant design in order to obtain the optimum performance of the processing equipment.

Jan 1, 1974

Gold mineralisation at the Kerimenge-Lemenge prospects is a classical example of myltiple, overprinting events, associated with intrusive-related hydrothermal systems. Repeated emplacement of high level dacitic porphyry bodies (Edie Porphyry; 2.4 - 3.8 Ma) was accompanied by a phreatomagmatic eruption which formed a diatreme-maar complex. Later hydrothermal fluids utilised permeable fault zones and diatreme contacts. Mineralisation took place during two main events. Stage I consists of early quartz - illite/sericite - carbonate phase with associated pyrite-arsenopyrite mineralisation. This phase is zoned from quartz - sericite-pyrite/arsenopyrite in the south at depth, to dominantly manganocarbonate - illitic clay - arsenopyrite- pyrite_s significant base metals in the north and at shallow levels. The majority of known gold (18.1 Mt @ 2.0 g/t Au) at Kerimenge is associated with Stage I activity. The gold occurs primary within the lattice of the sulphides and is metallurgically refractory. Fluid inclusion studies indicate early boiling and progressive cooling and dilution of hydrothermal fluids during the evolution of the Stage I event. Near paleosurface condensation of gases, which evolved off the boiling system at depth, produced abundant low pH bicarbonate fluids. During the waning phases of Stage I activity, these bicarbonate condensate fluids descended down permeable structures and formed banded manganocarbonate veins. High grade non-refractory gold mineralisation during Stage II event is restricted to favourable structures at relatively shallow levels and in the northern regions of the prospect area. Gold in this event exhibits a distinctive Au - Ag - Te -Cu geochemical signature, and is associated with hessite - tennantite - chalcopyrite mineralisation within quartz veining. Alteration and fluid inclusion studies indicate that this style of mineralisation is a result of the quenching of pulses of hot, late magmatic mineralised fluids by the cold condensate waters.

Jan 1, 1997

There is a well-known saying, variously attributed to the great King Solomon and other sages of antiquity, to the effect that 'there is nothing new under the sun'. The inventive genius of man, as far as it is personified in the metallurgist, has often had the truth of this statement poignantly brought to mind when investigating the priority of ideas in its own particular branch of science. Not infrequently some operation, at first inilocently taken for a novel procedure, has later been found to have had an irrefutable precedent in the more or less remote past.When confronted by a question of this kind the metallurgist can generally much simplify his search if he at once turns his scrutinising gaze towards that ancient home of metallurgy, Germany. Vast departments of the smelting art have originated there, and even when Germany has not been in position to claim priority of invention, it has at least been characterised by a distinction equally as worthy - ie that of the faithful and authoritative exposition of the theoretical grounds on which the invention rests.In the present instance, in endeavouring to trace the history of pyritic smelting, the writer has naturally turned in the abovementioned direction, and not without some result, although the recorded data are, as might have been expected, meagre. A complete history of the art of beneflciating ores by means of fire, in all its many ramifications, still remains to be written. Possibly it may never be written, for the extent of the subject is tremendous. It is even practically impossible to clearly trace the development of one of its most modest sub-branches in satisfactory detail, or to present that branch without going to a considerable extent into related matters of a merely general character. For the purpose of dealing with the subject it will be convenient to divide it into two concurrent heads, and to distinguish, for historical reasons as well as for metallurgical ones, between that branch of the general method of matte smelting, which, until about 1891, has been called 'pyritic smelting', and the more recent offshoot of the latter, which, by distinction, may be called 'pyrite smelting'. The nature of pyritic smelting was clearly defmed by Dr John Percy in 1880, and his interpretation3 may be accepted as well known. To recall the characteristics of the method we may perhaps paraphrase Dr Percy's meaning by describing the process as a special method for the smelting of lean or dry silver or gold ores, which do not contain sufficient lead or copper for these metals to act conveniently as collectors of the precious metals. The operation is conducted in a blast furnace, with an amount of carbonaceous fuel sufficing to produce an exclusively reducing atmosphere, and with the addition of pyrites, in order to form a regulus in which the precious metals shall be concentrated, the pyrites themselves being either argentiferous, auriferous, or cupriferous, or any combination of these three, or wholly barren of metal values. In the common acceptation of the term, it is understood that the use of the reverberatory furnace is excluded.

Jan 1, 1994

By Neto J. A N

Usually there are organisational interfaces between each stage - companies or departments. Each organisation will have different ideas about "optimum" operation. These ideas will be driven by how the performance of each is measured ' and rewarded. Therefore it is important to set up data acquisition processes with respect to maximisation of overall profitability and resource utilisation. In the simplest case - if the miners are paid on tonnes and the concentrator has severe grade penalties on concentrates, then there is the possibility of a conflict of interest over metal Balance.

Jan 1, 1991

By Gillies A. D S, Just G. D

The advancement of computer applications in the coal industry is focusing interest on the presentation of washability data by mathematical functions.The normal method of presenting washability data is in the form of five curves, usually filled by eye or by cubic spline functions. It has been shown that coal washability can be characterised by two basic relations: the instantaneous ash vs relative density relationship and the instantaneous yield vs relative density relationship. In a new approach to the mathematical modelling of the instantaneous ash vs relative density relationship, theapplication of the algorithm to a data set from a mine in central Queensland was successful.

Jan 1, 1991

By G D. Carman

White Rock is a reduced tungsten-tin skarn deposit near Rye Park, New South Wales. This abstract summarises the depositÆs mining and exploration history, and current exploration by Paradigm Metals Ltd targeting an economic resource at the deposit. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

The Wellington Dam catchment has high value water, agriculture and coal and power generating resources. These conflicting land uses are managed through consultation and regulation. The Wellington Dam catchment is unique in that the Collie Coal Basin is located almost to the edge of the dam and has coal mining and power generation as its primary land use. Currently the dam is only used for irrigation due to its high salinity. The State Government has committed to reduce the damÆs salt levels to below 600 mg/L by 2015 so that it can be considered for public drinking water supply. The coal industry in conjunction with the community and State Government has worked together to enhance the water quality within the Wellington Dam to maximise its value and use by using mine dewater for industry, diverting saline Collie River flows, providing environmental (social) flows and enhancing water quality of mine voids to encourage new industry to the Collie Region. Both surface and groundwater in the coal basin are generally fresh, whereas the salinity in the Collie River East Branch generally ranges between 3000 to 20 000 mg/L and 1700 to 10 000 mg/L in the South Branch. Mine dewatering is currently two to three times greater than the recharge to the coal basin. As a result, all mine dewater is sent to power stations in the area, with excess discharged into drainage lines which flow into the South Branch of the Collie River. To maintain environmental and social flows some groundwater is also pumped to the South and East Branches of the Collie River during summer months. Completed mine voids are used for recreation and options for aquaculture are promising. However, handback criteria are yet to be finalised.

Jan 1, 2006

Knelson concentrators are commonly used to recover fine liberated gold in gold processing plants. The decision to employ a gravity gold circuit consisting of centrifugal devices such as Knelsons is primarily taken on the results of GRG tests, among other considerations. While the GRG test is considered a material characterisation test, which is useful in the design stages, its use in evaluating the performance of an existing unit is questionable. The problem is exacerbated by the fact that it is time consuming and costly. This paper examines the validity of the GRG test for performance evaluation and discusses alternative test work that can be performed to evaluate the performance characteristics of an operating machine. Principles that are useful in selecting optimal operating parameters, such as optimal fluidising water flow rate for a given ore/machine combination, are also discussed and illustrated with laboratory and plant data.

Jan 1, 2007

By A G. Pavlides, B L. Weekes

The Sepon Copper Project is located in the Savannakhet Province of Laos PDR and is operated by Lane Xang Minerals Ltd (LXML). An Ausenco - Bateman Engineering joint venture, the Khanong Development Group (KDG) managed engineering, procurement and construction of the project. The plant was fully commissioned in March 2005, two weeks ahead of schedule. The plant is designed to produce 60 000 tpa of cathode copper. The process flow sheet includes a pressure oxidation (POX) circuit that leaches pyrite flotation concentrate to generate ferric ions and sulfuric acid for use in atmospheric leaching of a predominantly chalcocite ore. The process is unique in that the chemistry in the autoclave is forced to produce a basic ferric sulfate precipitate for downstream recovery of ferric iron. This paper describes the design, construction and commissioning of the pressure oxidation circuit. The challenges imposed on construction and commissioning due to the remote location of the site, landlocked status and underdeveloped infrastructure in Laos are highlighted.

Jan 1, 2005

By Chapman G. J

Mining operations require detailed and precise methods and procedures for the optimum selection of ore from waste. A fundamental procedure applied to achieve this selection is accurate sampling. The key parameter to accurate sampling is an understanding of the degree of heterogeneity of the key element contained within a sampling mass. This paper will describe the methods applied for the calculation of the fundamental sampling error and the techniques used to achieve a representative sample in the Fimiston Open Pit, Kalgoorlie.The utilisation of Pierre Gy's sampling theory has optimised the blast hole sample quality and quantity for submission to the assay laboratory. This has resulted in reduced cost and optimised assay reliability in statistical terms. Similarly the analysis of exploration drill holes for resource definition has optimised drilling procedures in terms of the drilling method, sample length and sample quantity.

Jan 1, 1993

By Bhattacharyya AK

A two-dimensional finite element modelling technique is applied to predict the subsidence movements on a sloping ground surface above a completely mined panel. The modelling is carried out for the surface both directly and using a combination of an equivalent horizontal surface and a rays projection method and the result compared. The rays projection method provides the subsidence components on a sloping surface from the corresponding ones on an assumed equivalent horizontal surface through the point of mean elevation of the relevant part of the sloping surface. This method is used next to compare the subsidences, horizontal displacements and horizontal strains from the mining of a given panel at the surface for different inclinations. The results show that the magnitudes of the subsidence components are greater on the dip side of the slope from the point of the mean elevation, than the corresponding ones on the rise side and the asymmetry increases with the inclination of the surface. The findings are also compared with those of other research Workers.

Jan 1, 1992

This paper describes the principle of cut-and-break rock excavation, in which rock is first undercut, and the undercut material is subsequently broken free by a wedging action. The current work on cut-and-break using the large rock cutting test rig at the Centre for Mining Technology and Equipment (CMTE) is outlined, and suggestions are made as to the potential advantages of cut-and-break roadheading, particularly in excavating short tunnels in hard rock in an urban environment.

Jan 1, 1993

Permian ultramafic and associated rocks form a belt in East Nelson and contain widespread, but minor, chromite and copper mineralisation and some mining was carried out last century. Since mining ceased, about 1910, little mapping of the belt has been carried out although its origin has been debated vigorously. Recently it has been inferred to form part of a ophiolite sequence, which has been tectonically disrupted to form a melange, and several 'plate -tectonic' models have been proposed. Mapping in the central part of the belt has shown that mTlanges are to the east of the ophiolite sequence. Faulting is widespread so that in anyone section part of the sequence may be absent. Some of the faulting is difficult to recognise and probably took place during or soon after the sequence accumulated. Other faulting is clearly of Cenozoic age and includes major NNE striking faults, with large horizontal displacement, and approximately east-west striking faults with almost entirely vertical movement. The writer agrees that 'plate tectonics' could provide an acceptable explanation for the origin of the ophiolite sequence but the models so far proposed do not take into account the nature and field relationships of the rock units present. Copper Mineralisation is largely controlled by the younger faults, particularly those striking about north-east, and is largely confined to the western part of the ultramafic rocks particularly where slivers of the volcanics of the adjacent Lee River Group are enclosed. Mineralisation, along NNE striking shear zones, has recently been found in the volcanics some distance from the ultramafic rocks. The chromite mineralization is in the form of primary layering in the basal part of the ultramafic belt although in places it has been concentrated into lenses probably during serpentinisation.

Jan 1, 1977

By Jackson S

An investigation into different aspects of importance in the understanding of explosibility of hybrid mixtures of coal dust, air and gases potentially found within mine workings through a comprehensive laboratory program of explosibility tests was conducted. Plotting of test results revealed that conditions of potential explosibility could be described using two dimensional flammability limit surfaces- for coal dust/oxygen; methane/oxygen; and coal dust/methane mixtures. From these plots, the three dimensional flammability envelopes defining the explosibility of the coal dust/methane/oxygen mixtures can be defined and illustrated for a coal sample. The surfaces of the three dimensional envelope describe limits which separate inert mixtures of coal dust and methane at varying oxygen levels from those concentrations which are ignitable under defined conditions. It is considered appropriate to generalise that the geometric shapes of these limit regions are applicable to all type classifications of coal dust. There are practical applications of these results to the underground environment.The action of free radical initiators in the propagation of a methane gas explosion was examined for its applicability to the flammability of coal dust/gas/air mixtures. The oxides of nitrogen or NO x radicals have influence upon the lean limits of flammability of hybrid mixtures and this is illustrated by use of three dimensional coordinate geometry. Gases can be introduced to the underground environment through the exhaust gases of diesel equipment. It is concluded that radical species can substantially increase the flammability of gas and dust flames and as a consequence raise risk of mine atmosphere explosibility.

Jan 1, 1998

There was a time, in the memory of some here tonight, when the annual meeting of The Institute was a nostalgic occasion. Often, in the 1920s, there was comment on the decline of Australian mining and on the lack of new mineral discoveries. When some of our Presidents prayed then for a new Bendigo, and instead were given a Mount Isa, they were justifiably disappointed because of the vastly different capital requirements.In 1967 the mining picture is very different. The recent mining developments in Australia are certainly as important as several Bendigos and several Kalgoorlies. The mining industry in Australia has never been more dynamic than today (Table 1). And if we ask why it is so dynamic, the answer lies in the role which overseas capital is playing in the industry. The contribution of overseas capital should concern us not only because we are members of the mining and metallurgical profession, but also because we have a duty to make our profession contribute as much as possible to the well-being of Australians. It is not sufficient to argue that overseas capital is good for the mining industry; we must also examine whether it is good for the economy and the nation. In this context the current criticism of the inflow of overseas capital into Australian mining is useful, for it gives us an opportunity to see what has resulted from the inflow.In discussing this question I do not suggest that we emulate Captain Hancock, that legendary Moonta mine manager who, according to Oswald Pryor's cartoon, used to say to his miners: "When I say a thing is, it is, even if it isn't". The question can only be discussed on a factual basis; and I would submit that many of the important facts relating to overseas capital in our mining industry are often overlooked or ignored. I would further submit, on the basis of these facts, that Australia's present day mining industry has been largely built on overseas capital and that the overall benefits of that capital to Australia have been enormous.

Jan 1, 1967

By Biswas AK, Hayes P

During the reduction of iron oxide pellets in the blast furnace it has been found that catastrophic swelling (up to 300% volume increase) can occur. Although the burden preparation conditions can be designed to avoid this phenomenon the exact reason and mechanism of the swelling has yet to be clearly identified. Swelling of the burden is undesirable since it reduces the interparticulate voidage in the blast furnace thus reducing gas flow through the stack resulting in low production rates of iron. The present study differs significantly from previous experiments in that reduction is carried out on single crystals of wustite thus the problems of control of gas composition and specimen preparation are minimised. The microstructures formed on reduction have been examined by optical and scanning microscopy. Pure wustite and wustite doped with various levels of CaO have been examined after reduction in controlled CO-CO 2 gas mixtures at 968¦C. The catastrophic swelling on reduction coincides with the formation of an unusually open iron structure in which the iron appears as whiskers or needles as previously reported. The spacing and thickness of the needles are shown to vary with impurity content and gas composition. Metallographic examination has shown in addition, however, that the whiskers do not necessarily constitute the only product form of the iron produced and in CaO containing wustites with less than - 2% CaO there is a transition from needle growth to porous growth of iron. Thus the % swelling of the oxide particles is dependent on the initial size of the oxide grains. Samples of FeO - 10% CaO exhibited a previously unreported product inorphology associated with the nucleation of 2CaO.Fe203.

Jan 1, 1980

MOUNT STEWART is situated half a mile south of Leadville railway station, which is distant 240 miles by rail from Sydney via Mudgee. It forms a low ridge from which rock waste and alluvium slope gradually to the black-soil flats of the Coolaburragundy River. The Mt. Stewart mine comprises:(a) The Mt. Stewart workings in M.L. 44, parish Talbragar, Co. Bligh.(b) The Grosvenor workings in M.Ls. 44 and 45, parish Talbragar, Co. Bligh.(c) The Extended workings in M.L. 44, parish Talbragar, Co. Bligh.The workings contain 1375 ft.. of vertical shafts, 1105 ft. of underlay shafts, 800 ft. of rises and winzes, 8520 ft. of drives and crosscuts, and 18,000 ft. of stapes.The mine was first opened in 1888 as a silver-lead mine, and a waterjacketed furnace was erected during 18B2. The furnace was installed with two internally-fired tubular boilers of 35 h.p. and 25 h.p. respectively, and two Baker's rotary pressure blowers. The results of the smelting campaign indicate that, during 14 months, a total of 15,000 tons of ore were treated, yielding silver and lead. In addition to this, a quantity of matte was sold containing about 8000 oz. of silver. As a result of the treatment...

Jan 1, 1925

Mine planning is difficult. Even for small operations, it involves reasoning with complex variables and the practical difficulties of mining. It is also about predicting and planning the future in an unpredictable physical and economic environment. Yet we rely on a handful of individuals and their spreadsheets to tell us how to do it û planning the business and activities of mining to hopefully produce results that will please stakeholders. Does it work? Not as well as it could. Planning affects everyone in the organisation. Company executives are demanding more reliability and stability in cost and revenue forecasts from their operations. Management want to explore ways of being more cost effective. Miners and contractors want more useful plans and realistic targets. And the planners have to describe the method that will translate business objectives into implementable plans. Even with the use of computer technology a lot of effort is expended to produce plans that are largely qualified by the level of knowledge and experience of individuals. Better use of information and the application of Intelligent Technologies can improve the quality and reliability of mine plans and schedules. By capturing the knowledge within the organisation and speeding up the planning process, Intelligent Technologies allow more options to be considered more rigorously. But it is not just about technology. It is about how technology is implemented and embodied in the way the business is managed for performance. When this happens, the real benefits of better planning start to flow.

Jan 1, 2003

By M Roper, M Lovitt

WMC Resources Olympic Dam Operation located in South Australia, is a poly metallic underground sublevel open stoping (SLOS) mining operation with a current annual production rate in excess of 9.0 Mt. Stope size, geometries, geotechnical considerations, drilling and blasting are critical components in stope performance. These factors are further influenced by stringent ventilation requirements due to the presence of airborne radioactive contaminants from uranium mineralisation. Stope planning is complex and mass blasting methodologies have been trialled at Olympic Dam with the view to reducing the frequency of stope blasts, improving stope stability, productivity and ultimately improving overall stope performance. A key aspect in the ability to undertake underground mass blasts of this scale is the application of i-konTM electronic initiation technology by Orica. In the past two years in excess of three million tonnes has been initiated utilising this electronic technology, with an average blast of 250 000 t ranging to the largest to date being 580 000 t. By providing flexibility in blast designs, the use of electronic detonators has allowed mass firings over multiple sublevels. This has resulted in a significant reduction in stope extraction steps compared to conventional pyrotechnic firings. The benefits of this reduction in the number of stope blasts are wide ranging from improved stability of interim stope voids between blasts, reduced blasthole damage, improved blast vibration management and reduction of complex changes to ventilation systems for blasting.

Jan 1, 2004